satmap Standard Power Bundle User Manual

Standard Power Bundle

User Guide

A selection of power and charging options available for use with the Active 10.
Includes a 2700mAh Lithium Polymer (LiPol) rechargeable battery optimized to
last longer over a wide range of temperatures and conditions. Ideal for users
who want a long battery life and the lowest possible running costs. Charge
options include mains charging, in-car charging and USB charging.

2700mAh LiPol Battery: Maximum Reserve Power

Normal Power Mode: 8 – 12 hrs
Advanced Power Saving Mode: 16 – 24 hrs
Hibernate Mode: 100 – 120 hrs

A

B

C

D

2700mAh Lithium Polymer Battery

Wall Charger with Multi-Country Adapter

Car Charger

USB Cable

The Standard Power Bundle consists of the following components:

B

A

C

D

Lock

E

F F

F F

G

I

H

J

K

Unlock

1

2 3

u

u

u

u

u

u

The battery compartment of the Active 10 can be found by removing the
Battery Back. Lift the metal D-ring on the back of the unit, rotate it a quarter
turn counter-clockwise to an unlocked position & lift the back off.

Next, remove the battery caddy (which holds AA batteries). Insert a small
at-headed screwdriver into the 4 gaps in each corner to loosen the
catches. Once the caddy is loose, gently pull out the white wire connector

from the battery socket in the top left corner .

Take the white wire connector of the LiPol battery and slot it into the top

left battery socket , ensuring the black wire is on the left. Do not use
excessive force.

For the best tting, make sure the label of the Lipol battery is facing
upwards. The wires should protrude from the right of the battery and t into
the top right gap within the foam seal. Fix the battery into position in the

back of the unit.

Ret the Battery Back onto the back of the unit. Locate the tab at the base
and slide it into the unit rst, making sure you do not trap the wires.

To secure the Battery Back into place, rotate the metal D-ring a quarter turn
clockwise to a locked position . (You may need to press down gently

to turn it).

F

E

G

H

K

I

J

Inserting the LiPol Battery:

3 Ways to Charge your LiPol:

The LiPol needs to be charged while in the Active 10. For optimum

performance it is important that you only use Satmap products to charge

the LiPol:

USB charging (via a computer using a USB Cable)

Mains charging (using the USB Cable and Wall Charger)

In-car charging (via the USB Cable and Car Charger)

1

2

3

LiPol Safety:

Only use specic charger.

Do not short circuit.
Do not disassemble.
Do not expose to high temperatures.
Do not incinerate.
Dispose of properly.

Phone (UK): [phone]
Phone (US): 1-888-226-5430

Email: [e-mail]

satmap.com

Disclaimer: Satmap is not liable for damages and injuries caused by

improper use or tting of the Standard Power Bundle. Satmap does not
disclaim any statutory rights relating to faulty or misdescribed goods that
cannot be disclaimed under applicable law. Subject to technical changes
and errors. Translations into languages other than English are provided
for information only. In the event of any confusion, the English text is the
controlling language. Please note: product specications are liable to
change without notice.

STDPB-UG-EN-1110

Important Information on Charging Your Unit:

u The unit takes approximately 8 – 10 hours to charge with a 2700mAh

LiPol battery.

u As soon as your unit starts charging, it will switch itself on.

u The battery indicator in the top right of the screen will show a lightning

symbol. Once this symbol appears, you should switch off the unit to
conserve energy. (This will only switch the screen off).

u To check whether your unit has been fully charged you will need to unplug

the unit. (The lightning symbol will not disappear when the unit is fully
charged because the charge protection circuit is always running, thereby
using up a small amount of charge).

u A fully-charged unit will show a solid green battery indicator, which will

gradually break down into four, three, two and nally one bar as the
charge decreases.

u When a single bar remains, it is coded red. After some further time, there

is an on-screen warning that the unit will power off in 30 seconds and a
countdown is shown.

u Ensure you have the ‘Screen Alert Every Minute’ set to ‘Off’: MAIN MENU

→ Settings → Power Control → Alert When Screen Off → Off. This allows

you to achieve a full battery, as all power goes into the battery and not
into running the unit.

u The battery has its own charge protection current so it will not overcharge

if you leave it running.