Satechi Lite Headphones User Manual

BT LITE Headphones

USER MANUAL

Introduction

Congratulations on your purchase of the
Satechi BT Lite Headphones. The BT Lite
Headphones is a Bluetooth multimedia
audio device capable of connecting to your
Bluetooth enabled phone, tablet, or
computer wirelessly. Once connected you
can stream music from your device to your
headphones.

Parts & Functions

1. Headband

2. Headband Adjustment

3. Previous Track

4. USB Charging Port

5. Multi Function Button

6. Next Track

7. Microphone

8. Earpiece

9. Power Switch

10. Volume Down

11. Volume Up

1

2

3

4

5

11

10

9

6

Charging the headphones

The BT Lite Headphones have a built-in
rechargeable battery. The battery must be fully
charged before using it for the first time. Make
sure to turn the headphones off before
charging.

1. Plug the charger into the outlet

2. The indicator light will appear solid red
when charging

3. A full charge takes approximately 2-3
hours

4. The indicator light will appear solid blue
when charging is completed

Powering on/off

Turn the headphones on by sliding the Power
Switch (9) until a beep sounds and the
indicator light flashes blue.
Turn the headphones off by sliding the Power
Switch (9) until a beep sounds and the
indicator light flashes blue twice.

8

7

Pairing your phone via Bluetooth

1. Ensure the headphones are on and within a
few feet from your phone.

2. Press and hold the Multi-Function button (5)
until the indicator light remains solid blue.

3. Ensure that your phone’s Bluetooth function
is turned on, then select the headphones from
your phone’s Bluetooth list.

4. Enter the passcode “0000”
***If pairing is successful, the indicator light will
flash blue 10x rapidly before flashing every 3
seconds.
***If pairing is unsuccessful, the indicator light
will remain on.
***If pairing takes more than 60 seconds, the
indicator light will go out and pairing will need
to be done again.

Disconnecting the headphones

To disconnect the headphones from your
phone, do one of the following:

- Turn the headphones off.

- Disconnect the headphones from the
Bluetooth list on your phone.

- Move the headphones 33ft away from your
phone.

3 4 5

1

Reconnecting the headphones

To reconnect the paired headphones with your
phone, do one of the following:

- Turn the headphones on and set up the
connection with the Bluetooth list in your
phone.

- Press the Multi-Function button (5) once (your
phone must have already been paired with the
headphones for automatic connection)

Answering a call

When a ringtone sounds, press the Multi­Function button (5) once to answer.

Ending a call

Press the Multi-Function button (5) to end a
call or end the call from your phone.

Answering/rejecting a call while
listening to music

If an incoming call is made while listening to
music with the headphones, press the
Multi-Function button (5) to answer the call or
press and hold the Multi-Function button (5) for
about 2 seconds to reject the call.

2

Placing a call on hold

During a phone call, press and hold the
Multi-Function button (5) for 2 seconds to
place the call on hold. To resume the call, press
and hold the Multi-Function button (5) again for
2 seconds (feature is subject to phone’s
capability)

Redialing previous number

Press and hold the Multi-Function button (5) for
2 seconds until a long beep sounds.

Playing music

Press the Multi-Function button (5) to play or
pause music. Press the Next Track button (6) to
skip to the next track and the Previous Track
button (3) to skip to the previous track.

Volume Control

Press and hold the Volume Up button (11) to
increase the volume, then release. Press and
hold the Volume Down button (10) to decrease
the volume, then release.