Sartorius YDI01C-WP Installation Instructions Manual
Installation Instructions
Sartorius
YDI01C-WP (Option A6|A7)
Installing a Digital Interface in Place of an A/D Converter in
Combics Indicators, Models CIS1..|CIS2..|CIS3.. | CISL1..|CISL2..|CISL3..
98647-003-78
The YDI01C-WP digital interface built into
the Combics indicator enables connection
of any of the following:
– Digital weighing platform
(e.g. IS weighing platform) using the
YCC02-R12F6 connecting cable (Option
M41: 12-contact round female connector;
length: 6 m; open cable ends), or
– Digital weighing instrument (e.g., LA, LP,
ME, EA, EB, CP balance/scale) using the
YCC02-D25F6 connecting cable (Option
M42: 25-pin D-Sub male connector;
length: 6 m; open cable ends), or
– Digital weighing instrument (e.g. QA,
QC, FB, FC scale) using the YCC02-R12M6
connecting cable (Option M43: 12-pin
round male connector; length: 6 m;
open cable ends).
Note: To have devices communicate with the Combics indicator as platforms and scales through the SBI protocol, configure the operating menu
as follows:
Baud rate: 9600 Handshake mode: Hardware, 1 character after CTS
Parity: Odd Number of data bits: 7
Stop bits: 1
Printing: Automatic without stability
Identification: With ID code (22 characters)
To have devices communicate with the Combics indicator as platforms and
scales over the xBPI protocol, configure the operating menu as follows:
Setting: xBPI protocol
Interface: RS-232 or RS-485
! Refer to the relevant operating instructions for descriptions of the
operating menus.
The menu setting in the Combics indicator depends on the particular
platform to be connected:
Setting: SBI or xBPI protocol
Interface: RS-232 or RS-485
Example: For Combics 1 and 2, this setting is configured in the Setup
menu; for Combics 3, in the menu under Device parameters
WP1
RS-232 or RS-485
SBI: Standard o IS-485
SBI: Trade ADC-485
o IS-232
ADC-232
! Always make sure the equip-
ment is disconnected from
power before performing any
installation, maintenance or
repair work.
! Work that affects IP protec-
tion must be carried out with
extreme care.
! Any installation work that
does not conform to the
instructions in this manual
will void all claims under the
manufacturer’s warranty.
! Do not operate the YDI01C-
WP in hazardous areas.
§ Place the Combics indicator
on a soft surface and remove
the four cap nuts from the
front panel.
§ Remove the front panel
Installing the YDI01C-WP PCB
§ Remove the A/D converter
PCB
– Unplug the male connector
– Remove the 3 screws
– Remove the A/D converter
PCB
§ Plug in the YDI01C-WP PCB
– Use the 2 screws to fasten
the PCB
– Plug in the male connector
Printed in Germany on paper that has been bleached without any use of chlorine · W1A000 · KT
Publication No.: WYD6122-e06032
§ Install the power
supply cable and
connect it as
described below
(see arrows)
1. To the YDI01C-WP
PCB
2. To the power supply
PCB
3. To the DC/DC
converter PCB
Configuration
Install connectors on the open cable ends and set the jumpers
according to the desired operating mode
LV1
Pin Signal
1 Power supply: +15 to 25 V (Line)
2 TXD (RS 232)
3 RXD (RS-232)
4
Supply ground (GND)
LV2
Pin Signal
1 GND
2 RXD-TXD-N (RS-485)
3 RXD-TXD-P (RS-485)
4 GND
Device selection:
Jumper 1
Device Position
CIS.1 1.1
CIS.2 1.1
CIS.3 1.1
Interface selection:
Jumper 2
Operating mode Position
RS-485 2.1
RS-232 2.2
Operating mode selection
in RS-485 mode:
Jumper 3
RS-485 mode Position
W/o terminating resistor 3.1
With terminating resistor 3.2
§ Place the front panel on the indicator
§ Place the Combics indicator on a soft
surface and attach the four cap nuts for
the front panel.
1
2
7
3
6
4
5
Overview of the YDI01C-WP PCB
1) Configuration jumper: 1
2) Connecting cable for the DC/DC converter
3) Male connector for connecting the power supply PCB
(cable enclosed)
4) LV1
5) LV2
6) Configuration jumper: 3
7) Configuration jumper: 2
1
2
3
Loading...