Sartorius PMA 7501-000G,PMA 7501-000GL Installation Instructions Manual
98648-015-03
Installation Instructions
Sartorius PMA.World | PMA.Net
Model PMA 7501-000G | PMA 7501-000GL
Electronic Paint-mixing Scales
2
General View of the Equipment
PMA7501-000G | PMA7501-000GL
(PMA.World | PMA.Net )
1 Display and control unit
2 Q key (On/Standby)
3 R key: Upwards
4 S key: Downwards
5 U key: Zero/Tare
6 I key (TOGGLE)
With the PMA.World Scale Series |
PMA.Net, you can toggle to two decimal
places – from 0.05 g to 999.95 g – or
toggle between – “g” and “p” – parts per
pound, depending on the menu settings
7 K factor key (FORMULATION) for
paint-mixing applications
8 c key (Clear) and [REC] key for
paint-mixing applications
9 L key [ENTER] and [MEM] key for
paint-mixing applications
10 Graphic display
11 Weighing pan
12 Interfaces (D-Sub plug, 9-contact,
Series PMA.World), Ethernet interface
(RJ45, Series PMA.Net)
13 Connection to AC power
14 Column
15 Joint
The following symbols are used in
these instructions:
§ Indicates required steps
$ Indicates steps required only under
certain conditions
> Describes what happens after you have
performed a particular step
– Indicates an item in a list
! Indicates a hazard
1
2
3
4
5
6
7
8
9
16
15
14
13
12
10
11
3
Contents
2 General View of the Equipment
PMA7501-000G | -000GL
3 Contents
3 Intended Use
4 Warning and Safety Information
5 Getting Started
7 Operating the
PMA7501-000G | -000GL
9 Applications
12 Calibration/Adjustment
13 Menu Settings
18 Troubleshooting
19 Care and Maintenance
20 Information and Instructions
on Disposal and Repairs
21 Pin Assignment
21 Specifications
22 Accessories
22 C Marking
The PMA7501-000G | -000GL (Series:
PMA.World | PMA.Net) scales feature
a graphic display, and have has been specially designed for use in the
paint-mixing sector.
The PMA.Net is equipped with an
Ethernet interface and can either be
directly connected to the network
interface of a PC, or via a 10BaseT/
100BaseTX LAN.
This scale can be operated either using
the keypad on the display and control
unit (in “stand alone“ mode) or using the
application software (e.g., paint manufacturers’ paint-mixing applications)
installed on your PC. Communication is
carried out via the data interface.
If required, Sartorius can supply you with
DOS- or WINDOWS-based device drivers
to generate application
programs.
Note:
Read the PMA7501-000G | -000GL
installation and operating instructions
carefully before connecting the
weighing platform and putting it into
operation.
- According to Certificate No. 781 553419
issued by TÜV NORD CERT GmbH
(German Inspection and Safety Authorities), PMA7501-... electric scales and their
respective power supplies, models STNG 6
and TNG 6 (only with the power supply
of H03 provided by Sartorius, or a similar
type)may be used in areas exposed to the
risk of fire, provided that the room is not
impacted by larger amounts of accumulated dust and fiber, and thus a fire risk.
Paint-mixing rooms are free of such
accumulated dust and fiber, and the
equipment can be operated there.
Intended Use
4
Warnings and Safety Precautions
This scale meets the guidelines and standards governing electronic equipment,
electromagnetic compatibility and the
stipulated safety standards. Improper use
or handling can result in property damage and/or personal injury. To prevent
damage to the equipment, read these
operating instructions
thoroughly before using your scale. Keep
these instructions in a safe place.
– Do not expose the scale to extreme tem-
peratures, aggressive chemical vapors,
moisture, shocks and vibrations
– The display values can be impacted when
subjected to extreme electromagnetic
influence. When the negative influence
has subsided, the scale will again be fully
operational.
– The equipment must be used indoors
– The scale may not be operated in
hazardous/ EX Zone areas
– To ensure safety, disconnect the equip-
ment from power before connecting or
disconnecting the cables or electronic
peripheral devices
– If you use cables purchased from
another manufacturer, check the pin
assignments in the cable against those
specified by Sartorius before connecting
the cable to Sartorius equipment, and
disconnect any wires that are assigned
differently. The operator shall be solely
responsible for any damage or injuries
that occur when using cables not
supplied by Sartorius.
– When connecting the scale to the power
supply, the laws valid in your country
must be observed. If you should have any
questions, please contact your supplier or
Sartorius Customer Service for information on the legal regulations applicable in
your country. The scale must be installed
by a certified technician to avoid forfeiture of all claims under the manufacturer’s
warranty.
– If you see any indication that the scale
cannot be operated safely (for example,
due to damage), turn it off and lock it in
a secure place or otherwise prevent use of
the equipment for the time being. Adhere
to the accident prevention regulations
and inform the operators, accordingly.
– Always make sure the equipment is
disconnected from AC power before
performing any installation, cleaning,
maintenance or repair work on the scale.
To avoid forfeiture of all claims under the
manufacturer’s warranty, all repair and
maintenance work must be performed by
authorized Sartorius service technicians.
– All other cables connecting the weighing
equipment and peripheral devices, as well
as the wiring inside the devices, are cased
in PVC materials. Chemicals that corrode
these materials must be kept away from
these cables.
– Never use a hammer to close the lid of a
paint can while it is still on the weighing
pan. Otherwise, you will damage the
weighing system.
Getting Started
§ Remove the scale from its packaging.
§ After unpacking the scale, check it immediately
for any visible damage as a result of rough handling
during shipment.
Equipment Supplied
– Scale
– Weighing pan
– AC adapter or power supply
–2+ protective plugs (in the column)
Setting Up the Scale
Choose a suitable place to set up the scale.
Avoid exposure to drafts, heat, moisture and vibration. Make sure to read the instructions carefully
before connecting the scale to AC power.
!Observe the safety instructions and warnings in this
manual.
§ Place the weighing pan on the scale.
5
°C
6
Connection to AC Power
The equipment is powered through the AC adapter
supplied
§ Insert the right-angle plug into the IEC jack (13) on
the scale
§ Plug the AC adapter into an electrical AC power outlet
!Observe the safety instructions and warnings in this
manual
The equipment is powered through the AC adapter
supplied. Check that the voltage rating of the AC
adapter matches that of your local line voltage (mains
supply). If it does not match your local voltage rating
or if the plug design differs from your local standard,
contact your Sartorius office or dealer. Use only genuine Sartorius AC adapters! The use of AC adapters
from other manufacturers, even if these units have a
registered approval rating from a national testing laboratory, requires the approval of a certified technician.
Connecting the Data Cable
§ The series PMA.Net are equipped with an Ethernet
interface (12) and can either be directly connected to
the network interface of a PC, or via a
10BaseT/100BaseTX LAN.
§ Connect the Ethernet cable
§ The series PMA.World are equipped with a (D-Sub
plug, 9-contact) interface (12).
§ Connect the data cable and tighten the screws.
Operating the PMA7501-000G | -000GL
Weighing with One Decimal Place
Place an empty paint can on the weighing pan.
Press the U key (5). The display shows “0.0 g.”
Pour in the first component, and read off the weight as
soon as the stability symbol appears; in this case, “g.”
Pour in additional components until the desired weight
of your formula is reached.
Remove the filled paint can from the weighing pan.
Never use a hammer to close the lid of a paint can
while it is still on the weighing pan.
Otherwise, you will damage the weighing system.
7
Turn on the scale using the
Q key (2).
After the scale has been
turned on, it will automatically run a self-test.
At the end of this test, 0.0 g
is displayed.
If a different readout is
displayed, zero or tare the
scale using the U key (5).
Weighing with Two Decimal Places
Note:
To weigh using two decimal places, you must first
adapt the settings (refer to the chapter on “Menu
Settings)
Press the I key (6). The display shows “0.00 g.”
Place an empty paint can on the weighing pan (11).
Press the U key (Zero/Tare) (5). The display shows
“0.00 g.”
Pour in the first component: 205.50 g.
Read off the weight as soon as the stability symbol
appears; in this case, “g.”
Pour in additional components until the desired weight
of your formula is reached.
Remove the filled paint can from the weighing pan.
Important Note:
If you zero the display by pressing the tare key,
and then press the I key (6) to toggle to the second
decimal place with a resolution of 0.05 g, you can
continue weighing up to 999.95 g.
For weights exceeding 999.95 g, only one decimal place
will be displayed.
Never use a hammer to close the lid of a paint can
while it is still on the weighing pan.
Otherwise, you will damage the weighing system
8
Loading...