Sapling STR 2000 Series Programming Manual

STR 2000 Series Transceiver Programming Manual

TABLE OF CONTENTS

PROGRAMMING THE DATE

Programming the Date……..…………………………………………………………… Page 2

TECHNICAL MODE

Technical Mode......…………………………………………………………………….. Pages 2 - 3

PROGRAMMABLE RELAY MODE

Programming the Relay………………………………………………………………... Pages 3 - 4

INTERFACING

Auxiliary Input Control.……………………………………………………………….. Pages 4 - 6

DISPLAY MODE

Clock Information……………………………………………………………………… Pages 6 - 7

SELF- TEST MODE

Self-Testing Mode……………………………………………………………………... Pages 7 - 8

DIAGNOSTIC MODE

Diagnostics to the Slave Clocks………………………………………………………… Page 9

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 1

STR 2000 Series Transceiver Programming Manual

Once programming mode has been entered, the number
“01” will appear in the far left position (see diagram).
This prompt allows you to set the year. Use the “Set
Minute” button to scroll from “00-99” on the display
and set the year.

Press the “Set Hour” button to advance to option 2. A
“02” will appear on the left side of the LED display.
This prompt allows you to set the month. Use the
“Set Minute” button to scroll between “01-12”.

Left Digit Right Digit

Press the “Set Hour” button to advance to option 3. A
“03” will appear on the left side of the LED display.
This prompt allows you to set the day. Use the “Set
Minute” button to scroll between “01-31”.

Pressing the “Set Hour” button will advance to option 04.
A “04” will appear on the left of the LED display. This

option shows the user if daylight savings time is en­abled (Left Digit 1 Enabled, 0 Disabled) and if the
date is in the summer months (Right Digit 1 Summer,
0 Winter) .

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 2

STR 2000 Series Transceiver Programming Manual

Press the “Set Hour” button to advance to option 10. A
“10” will appear on the left side of the LED display.
This prompt allows you to enter into technical mode.
If technical mode is desired, press the “Set Minute” to
“08” to enter technical mode. The scrolling will scroll
through “00-99”. Any other character will go directly
to option “20”.

Press the “Set Hour” button to enter technical mode which
starts with option 11. An “11” will appear on the left side
of the LED display, if the option was chosen in option 10.
This prompt allows you to set the data transmission.
Press the “Set Minute” button to scroll between “01-12”.

01 - Data is transmitted every second 07 - Data is transmitted every 2 minutes
02 - Data is transmitted every 5 seconds 08 - Data is transmitted every 5 minutes
03 - Data is transmitted every 10 seconds 09 - Data is transmitted every 10 minutes
04 - Data is transmitted every 15 seconds 10 - Data is transmitted every 15 minutes
05 - Data is transmitted every 30 seconds 11 - Data is transmitted every 30 minutes
06 - Data is transmitted every minute 12 - Data is transmitted every hour

Press the “Set Hour” button to enter option 12. A “12”
will appear on the left side of the LED display. This

option allows the user to enable or disable Daylight
Savings Time. Press the “Set Minute” button to scroll

between “E - D”. “E” will enable this option. “D” will
disable this option.

Press the “Set Hour” button to enter option 20. A “20”
will appear on the left side of the LED display. This

option allows you to enter a programmable relay
output mode. Press the “Set Minute” button to scroll

through “E - D”. Prompting “D” will go directly to
option 30. Prompting “E” will enter the programmable
relay output mode.

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

STR 2000 Series Transceiver Programming Manual

Press the “Set Hour” button to enter option 21. A “21”
will appear on the left side of the LED display. This

option allows you to set the hour that the user wishes
the relay to close at. Press the “Set Minute” button to

scroll through “01-23”.

Press the “Set Hour” button to enter option 22. A “22”
will appear on the left side of the LED display. This

option allows the user to set the minute(s) they want
the relay to close at. Press the “Set Minute” button to

scroll between “00-59”.

Press the “Set Hour” button to enter option 23. A “23”
will appear on the left side of the LED display. This

option allows the user to set the second(s) they want
the relay to close at. Press the “Set Minute” button to

scroll between “00-59”.

Press the “Set Hour” button to enter option 24. A “24”
will appear on the left side of the LED display. This

option allows the user to set the duration of the relay
closure. Press the “Set Minute” button to scroll be-

tween “00-99” (seconds).

Page 4

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

STR 2000 Series Transceiver Programming Manual

Press the “Set Hour” button to enter option

30. A “30” will appear on the left side of the LED dis­play. This option allows the user to allow an auxil-
iary input control. Press the “Set Minute” button to
scroll between “E - D”. Setting the option to “D” will
disable the option and go directly to option 40. Setting
the option to “E” will enable the user to enter an input
control mode.

Pressing the “Set Hour” button will go to option 31. A
“31” will appear on the left side of the LED display.
This option allows the user select the input. Pressing
the “Set Minute” button will allow the user to scroll
between “01-07 and 10”.

01 - Internet Connection 05 - Dukane Digital
02 - 59 Minute Correction 06 - Rauland Dig. Out
03 - 58 Minute Correction 07 - Wireless Input
04 - National Time/Rauland 10 - Once A Day Pulse

Pressing the “Set Hour” button when option 31 is set to
“01”, will enter option 32. A “32” will appear on the
left side of the LED display. This option allows the

user to set the positive offset of the user’s location
when the Internet Connection is selected. Press the

“Set Minute” button to scroll through “00-23”.

Pressing the “Set Hour” button when option 31 is set to
“01”, will enter option 33. A “33” will appear on the
left side of the LED display. This option allows the

user to set the negative offset of the user’s location
when the Internet Connection is selected. Press the

“Set Minute” button to scroll through “00-23”.

Page 5

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

STR 2000 Series Transceiver Programming Manual

Pressing the “Set Hour” button when option 31 is set to
“10”, will enter option 34. A “34” will appear on the
left side of the LED display. This option allows the

user to set the hour they want the time to go to when
Once A Day Pulse is selected. Press the “Set Minute”

button to scroll through “00-23”.

Pressing the “Set Hour” button will enter option 35. A
“35” will appear on the left side of the LED display.

This option allows the user to set the minute they
want the time to go to when Once A Day Pulse is
selected. Press the “Set Minute” button to scroll

through “00-59”.

Pressing the “Set Hour” button will enter option 34. A
“34” will appear on the left side of the LED display.

This option allows the user to set the seconds they
want the time to go to when Once A Day Pulse is
selected. Press the “Set Minute” button to scroll

through “00-59”.

Press the “Set Hour” button to enter option 40. A “40”
will appear on the left side of the LED display. This

option displays the last time the clock received an
input signal (in hours). The display will be between

00 - 99. This option is read only. It cannot be modi­fied.

Page 6

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

STR 2000 Series Transceiver Programming Manual

Press the “Set Hour” button to enter option 41. A “41”
will appear on the left side of the LED display. This

option displays the current temperature of the clock
itself. The temperature will display in °C. This option

is a read-only option.

Press the “Set Hour” button to enter option 44. A “44”
will appear on the left side of the LED display. This

option displays whether the transceiver is receiving
an Internet Connection. A “01” will appear on the

right side if the master is receiving an Internet Connec­tion. A “00” will appear on the right side if it is not
receiving an Internet Connection. This option is a read­only option.

Press the “Set Hour” button to enter option 50. A “50”
will appear on the left side of the LED display. This
option enters the self testing feature. Press the “Set
Minute” button to scroll between 00-99. To enter the
Self Test mode, press the “Set Minute” button till a
“15” is displayed to the right. Any other character will
go directly to option 60. After it is set to “15”, press the
“Set Hour” button to enter the Self Test mode.

Press the “Set Hour” button to enter option 51. A “51”
will appear on the left side of the LED display. This
option tests the Real Time Clock. When the “Set
Minute” button is pressed, the display will count up
from 57 to 00. If the Real Time Clock is working prop­erly, the transceiver will advance to option 52. If it
does not, it will stay at option 51.

Page 7

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

STR 2000 Series Transceiver Programming Manual

Press the “Set Hour” button to enter option 52. A “52”
will appear on the left side of the LED display. This
option tests the output relay. When the “Set Minute”
button is pressed, the relay will close. When the “Set
Hour” button is pushed, the relay will open and advance
to the next option.

Press the “Set Hour” button to enter option 53. A “53”
will appear on the left side of the LED display. This
option tests the segments of the LED display. When
the “Set Minute” button is pressed, the segments will
test one segment at a time. To advance to the next op­tion, press the “Set Hour” button.

Press the “Set Hour” button to enter option 54. A “54”
will appear on the left side of the LED display. This

option tests the transceiver to see if it recognizes an
input. If there is no input, the digits to the right will

read “00”. If there is an input, the digits to the right will
read “01”.

Press the “Set Hour” button to enter option 55. A “55”
will appear on the left side of the LED display. On the
right side of the display, the left digit will be alternating
every 200ms between “0” and “1”. The right digit will
stay at “0”. This option tests the RS485 and RS232
input and output. To test the RS485, short the input
and the output. When this occurs, the right digit will
synchronize with the left digit. To test, the RS232,
short the input and the output. When this occurs, the
right digit will synchronize with the left digit.

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Left Digit Right Digit

Page 8

STR 2000 Series Transceiver Programming Manual

Press the “Set Hour” button to enter option 60. A “60”
will appear on the left side of the LED display. This

option allows the user to enter diagnostic mode.

Press the “Set Minute” button scroll between “E - D”.
Setting the option to “E” will enable the option and will
enter diagnostic mode. Setting the option to “D” will
disable the option, then pressing the “Set Hour” button
will bring the display back to the set time.

Press the “Set Hour” button to enter option 43. A “43”
will appear on the left side of the LED display. This

option allows the user to send the diagnostic to the
slave clocks. Pressing the “Set Minute” button will

scroll from “01-05”.

01 - Protocol Verification
02 - Comprehensive Test
03 - Manufacturer’s Default
04 - Combination of 02 & 03 (button must be pressed on SAM)
05 - Combination of 02 & 03 (no need to press button on SAM)
09 - Overrides the Previous Diagnostic and Goes Back to the Time

Pressing the “Set Hour” button will advance to option 62.
A “62” will appear on the left of the LED display. This

option allows the user to set how long (in minutes)
that the information display from the diagnostic will
stay on the clock. Pressing the “Set Minute” button will

scroll from “00-99”. Pressing the “Set Hour” button will
go back to the displayed time.

Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 9