Sapling SALG Series, SAL Series Installation Manual

Installation Manual V5.5

SAL/SALG Series Wireless Clock

Current as of July 2016

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

SAL/SALG Series Wireless Clocks

Table of Contents

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Table of Contents 2 Important Safety Instructions 3 Identify Your Clock 4 Synchronization System Setup 5 - 7

Wall Mount Installation -

- Round Standard ABS Clock - Battery Powered 8 - 10

- Locally Powered 11 - 13

- Round SlimLine Clock - Battery Powered 14 - 16

- Locally Powered 17 - 20

- Round Aluminum/Wood Clock - Battery Powered 21 - 24

- Locally Powered 25 - 29

- Square Clock - Battery Powered 30 - 33

- Locally Powered 34 - 37

Flag Mount Installation -

- Round Standard ABS Clock - Battery Powered 38 - 43

F - Locally Powered 44-49

Troubleshooting 117 - 118 Diagnostic #1 - Signal Information 119 Diagnostic #2 - Signal Quality 120 Diagnostic #3 - Manufacturing Default 120 - 121 Diagnostic #4 - Battery Voltage 121 Warranty 122 FCC Statement 123

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be properly installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not powered, the secondary clocks will not synchronize.

- Round SlimLine/Aluminum Clock - Battery Powered 50 - 56

- Locally Powered 57 - 63

- Square Clock - Battery Powered 64 - 70

- Locally Powered 71 - 77

Double Mount Installation -

- Round Standard ABS Clock - Battery Powered 78 - 82

D - Locally Powered 83 - 87

- Round SlimLine/Aluminum Clock - Battery Powered 88 - 93

- Locally Powered 94 - 99

- Square Clock - Battery Powered 100 - 106

- Locally Powered 107 - 113 Legacy Movement - Battery Powered 114 Frequently Asked Questions 115 - 116

Manuals may change without prior notice

2

Important Safety Instructions

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

DANGER

! !

SHOCK HAZARD

,

• Keep the electricity to this device turned OFF until the clock installation is complete.

• Do not expose the clock movement to water, or install the clock in a location where it may be exposed to water.

H

|

NOTICE

• Do not install the clock outdoors. Damage to the clock if placed outdoors voids the warranty.

• Do not hang objects from the clock or clock mounting parts. The clocks are not designed to support the weight of other objects.

• The clock face and housing may be cleaned with a damp cloth or disinfectant. Test other cleaning products on a small part of the clock housing before attempting to use on the rest of the clock. Avoid bleach and chemicals known to dissolve plastics.

WARNING

FIRE HAZARD

• Always follow your national and regional electrical codes or ordinances.

• The AC power circuit for the clock must be attached to a circuit breaker that can be reset by the user.

PHYSICAL INJURY HAZARD

• If you are standing on an object while installing your clock, make sure that the object can support your weight, and will not sway or move as you stand on it.

• Take precautions to avoid injury by potential safety hazards near the point of installation including (but not limited to) heavy machinery, sharp objects, hot surfaces, or exposed cables carrying an electric current.

• Follow all mounting instructions exactly as stated in this manual. Failure to do so may result in the device falling off the point of installation.

• Packaging materials and mounting items include plastic bags and small pieces, which pose a suffocation hazard to young children.

3

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Identify Your Clock

A label containing the part number of your clock is attached to the clock movement.

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

If your part number begins with SAL-2 or SALG-2, you own a STANDARD ABS clock

If your part number begins with SAL-4 or SALG-4, you own a SLIMLINE ABS or SQUARE clock

If your part number begins with SAL-5 or SALG-5 you own an ALUMINUM clock

If your part number begins with SAL-6 or SALG-6 you own a WOOD clock

Example part numbers:

SAL-2BS-16R-1 (STANDARD ABS clock, 900 MHz)

SAL-4BS-12S-4 (SQUARE clock, 900 MHz)

SALG-4BS-12R-4 (SLIMLINE ABS clock, 2.4 GHz)

SAL-5AS-09R-1 (ALUMINUM clock, 900 MHz)

SALG-6DS-12R-2 (WOOD clock, 2.4 GHz)

Please note that STANDARD ABS clocks may use either the movement shown on the left or the one shown on the right. Instructions and diagrams have been provided for both variants.

All SlimLine, Square, Aluminum, and Wood clocks use the movement shown on the left.

4

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Synchronization System Setup

VERY IMPO RTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Instructions in this section refer to the Transmit/Receive button located on the clock movement. Review the illustration on the right if you have trouble ﬁnding it.

Normal/Economy Mode:

Battery-powered SAL/SALG series clocks can operate in one of two different modes.

Green

Red

Standard ABS

• Normal mode causes the SAL/SALG to receive and transmit every two hours. Using this mode, the clock will have a 5 year battery life, assuming that the clock has good reception and is using Duracell ProCell

Transmit/Receive

Diagnostic

batteries. Clocks are shipped to customers in this mode. If the SAL/SALG is being added to an existing

Diagnostic

Transmit/Receive

system, it must be set to normal mode.

• Economy mode causes the SAL/SALG to receive and transmit every four hours. Using this mode, the clock will have an 8 year battery life, assuming that the

Green

Red

clock has good reception and is using Duracell ProCell batteries.

The two modes may be toggled by pressing and releasing the Diagnostic Button seven times. If Normal mode is selected, the red LED will shine for one minute and the second hand will go to the 25-second position. If Economy mode is selected, the green LED will shine for one minute and the second hand will go to the 40-second position.

Manual Wireless Receiver Settings:

• If you power-cycle the clock (turn it off and turn it on again by removing the power connector or batteries), the receiver will be powered for ten minutes.

• If you press the Transmit/Receive button twice, the receiver will search for the time signal for ten minutes. During this time the hour and minute hands will function normally, but the second hand will move to the twenty second position until the signal is received. If a signal is received, the clock will synchronize the hands to match the time. If ten minutes have passed and a signal has not been received, the second hand will return to where it was when the button was pressed, then continue operating.

• If you press the Transmit/Receive button once, the transmitter will transmit the time signal for ten minutes. However, this will only occur if the clock has received a signal with time data during the past twelve hours. During this time, the second hand will move to the forty second position. After the ten minutes have passed, the second hand will return to where it was when the button was pressed, then continue operating.

All Other Clocks

5

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Synchronization System Setup (ctd.)

Positioning Transceivers:

The main transceiver should be installed in a central location where there is a minimum number of walls between the transmitter and clocks. After the main transceiver has been installed, begin installing the secondary clocks nearest to the main transceiver, followed by whichever clocks are nearest to the secondary clocks, and so on. Each secondary clock within range of the transceiver should receive data and begin correcting itself within ﬁve minutes of being powered on. Be aware of walls or other obstructions made of thick concrete or sheet metal, as these may block the signal entirely.

Manually setting a connection between two or more SALs:

1. Identify two clocks. The one which is receiving a signal from the Master Clock is your Transmitter clock, the one which is not receiving a signal is your Receiver clock.

2. Press the Transmit/Receive button on the Transmitter clock once. The second hand will move to the 40 second position and the clock will stop running. The Transmitter clock is now in transmission mode.

3. Press the Transmit/Receive button on the Receiver clock twice. The second hand will move to the 20 second position until the Receiver clock receives time from the Transmitter clock. You may perform this step with more than one Receiver clock at the same time.

4. As you move further away from the main transceiver, use one of your now-synchronized Receiver clocks as your new Transmitter, and continue the process.

System Setup Options

There are three ways to operate a system of Sapling’s SAL/SALG Series Wireless clocks. The user may choose one or a combination of the options listed below:

1. No clocks are used for transmission. This option should only be taken if the user already has a main high-powered transceiver and as many repeaters as needed to cover the premises.

2. Battery powered clocks are used as transceivers/repeaters. This option assumes that there is at least one high powered transceiver in range of enough of the clocks that the clocks can repeat the signal to all other clocks in the system.

3. Locally powered clocks are used as transceivers/repeaters. This option assumes that there is at least one high powered transceiver in range of enough of the clocks that the clocks can repeat the signal to all other clocks in the system.

Before performing any of these options, the user must install and power the master clock and main transceiver ﬁrst.

6

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Synchronization System Setup (ctd.)

System Option 1

No clocks are being used for transmission. This option should only be taken if the user already has a main high-powered transceiver and as many repeaters as needed to cover the premises. There are two methods for setting up a system that uses this option:

Method A: Transceivers or repeaters are synchronized wirelessly to the main transceiver.

1. Place the main transceiver in a central location, like a hallway, where the signal will not be blocked.

2. Pick the location for a secondary transceiver or repeater.

3. Place the secondary transceiver or repeater in a location where it can receive the signal from the main transceiver.

4. Power up the main and secondary transceivers. Within ﬁve minutes, the secondary transceiver should be showing the time of the main transceiver. If the secondary transceiver is failing to synchronize, install it closer to the main transceiver.

5. Repeat steps 1-4 with all additional transceivers or repeaters. Note that other transceivers or repeaters can receive signals from a properly synchronized secondary transceiver/repeater, not just the main transceiver/repeater.

System Option 2

Battery powered clocks are used as transceivers/repeaters. This option assumes that there is at least one high powered transceiver in range of enough of the clocks and that the clocks can repeat the signal to all other clocks in the system.

Either follow the previous instructions listed under “Manually setting a connection between two or more SALs”, or perform the following steps:

1. Install the batteries in the clocks while close to the main transceiver.

2. After each clock has received a signal from the transceiver and adjusted to the main transceiver time, place the battery cover back on.

3. Take each clock, while the clock is running, to the planned point of installation and mount the clock on the wall.

(NOTE: This method does not conﬁrm that the clocks are in range of each other)

System Option 3

Locally powered clocks are used as transceivers/repeaters. This option assumes that there is at least one high powered transceiver in range of enough of the clocks that the clocks can repeat the signal to all other clocks in the system.

In this state, locally powered SAL/SALG clocks will enable their receivers at all times, and will transmit time data once each minute.

7

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Round Standard ABS Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round Standard ABS analog clock

Included in Wiring Kit (A-WK-12-1)

Mounting Bracket

#10x1.5 Self-tapping screw

Wall anchor

#4x5/16 Screw

Quantity

1

2

1

Picture

Bracket Securing Nut

PLEASE NOTE: A user will also have to provide two D-Cell batteries, a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

1

8

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Standard ABS Clock

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Use the mounting bracket, a pencil, and a level to trace two holes on the wall, then use the 1/4 inch drill to drill holes at the locations of the two marks.

1 2

3) Remove the back cover from the battery pack by pulling the two latches away to either side and sliding the cover out.

2) Place the two wall anchors into the holes, then screw the two #10 self-tapping screws through the bracket and into the wall anchors.

4) First remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

3

For instructions regarding the original battery pack and movement design, refer to the section of this manual labeled “Legacy Movement - Battery Powered”.

1

4

2

9

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Standard ABS Clock

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

5

6) Slide the long, protruding part of the mounting bracket into the clock case keyhole.

6

7) Align the peg on the top portion of the mounting bracket with the hole on top of the clock case. Slide the peg through the hole. Use the bracket securing nut to secure the peg in place.

7

10

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Round Standard ABS Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round Standard ABS analog clock

Included in Wiring Kit (A-WK-12-1V)

Mounting Bracket

Power/grounding wires and connector

Bracket securing nut

Quantity

1

Picture

#10x1.5 Self-tapping screw

Wall anchor

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

2

1

11

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Standard ABS Clock

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Install the single gang box in the wall. Leave at least 17 inches between the bottom of the gang box and ceiling. Conﬁrm that the bottom of the gang box is level with the ﬂoor.

1 2

17” Minimum

43.2 cm

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

3) Attach the communication, power, and grounding wires from your kit to the communication and power wires in the gang box. See the Wiring Guide included later in this manual for additional details.

3

4) Position the top of the mounting bracket so that it is between 1 and 9 inches above the top of the gang box. Use the mounting bracket, a pencil, and a level to trace two holes on the wall, then use the 1/4 inch drill to drill holes at the locations of the two marks.

4

12

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Standard ABS Clock

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Place the two wall anchors into the holes, then screw the two #10 self-tapping screws through the bracket and into the wall anchors.

5

7) Slide the long, protruding part of the mounting bracket into the clock case keyhole.

6) First remove the gearbox pin, then attach the power connector to the port on the movement.

1

6

2

8) Align the peg on the top portion of the mounting bracket with the hole on top of the clock case. Slide the peg through the hole. Use the bracket securing nut to secure the peg in place.

2

7

8

13

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Round SlimLine Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round SlimLine analog clock

Included in Wiring Kit (A-SLM-MK-S-1)

Mounting Piece

#6-19x7/16 screw

Strain Relief

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

Quantity

1

2 (not used)

1 (not used)

2 (not used)

Picture

#6-19x3 /8 screw

Included in Wiring Kit (A-WK-MTG-1)

#10x1.5 Self-tapping screw

Wall anchor

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables. You may also need a 1/4 inch drill if you decide not to attach the clock directly to the gang box.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

1 (not used)

2

14

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round SlimLine Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Place the mounting piece on the wall. Leave at least 4 inches between the top of the gang box and ceiling. Conﬁrm that the bottom of the mounting piece is level with the ﬂoor.

4” Minimum

1

2) Use a pencil to mark the positions of the top two holes, then use the 1/4 inch drill bit to drill holes at the locations of the two marks.

2

3) Insert the wall anchors into the two holes, then place the two self tapping screws through the mounting piece and into the wall anchors.

3

4) Remove the back cover from the battery pack by pulling the two latches away to either side and sliding the cover out.

4

15

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round SlimLine Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) First remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

5

2

7) Attach the clock to the mounting piece by sliding the clock back onto it. You should hear a snapping noise as the latch engages.

6) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

6

8) If you need to take the clock off the wall after the installation has been completed, use a ﬂat-blade screwdriver or eyeglasses screwdriver to lower the mounting piece latch, then slide the clock off the mounting piece.

7

8

16

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Round SlimLine Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round SlimLine analog clock

Included in Wiring Kit (A-SLM-MK-S-1)

Mounting Piece

#6-19x7/16 screw

Strain Relief

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

Included in Wiring Kit (A-WK-MTG-1V)

Quantity

1

2

1

2

1 (not used)

Picture

Power/grounding wires and connector

#8x1.5 Self-tapping screw

Wall anchor

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables. You may also need a 1/4 inch drill if you decide not to attach the clock directly to the gang box.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

1

2

17

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round SlimLine Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) If you are installing a new gang box in the wall, leave at least 4 inches between the top of the gang box and ceiling. Conﬁrm that the bottom of the gang box is level with the ﬂoor.

If you are using an existing gang box, the top of the gang box must be a minimum of four inches away from the ceiling.

Ceiling

1

Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Attach the power wires from your kit to the power wires in the gang box.

• Attach the Hot wire to the connector’s black wire.

• Attach the Common wire to the connector’s white wire.

• Attach the Ground wire to the connector’s green wire.

3 4

4) If you do not wish to attach the mounting piece to the gang box, proceed to step 5A. Otherwise, go to step 6.

18

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round SlimLine Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5A) If you do not wish to attach the mounting piece to a gang box, place the mounting piece on the wall. Leave at least 4 inches between the middle of the mounting piece and ceiling. Conﬁrm that the bottom of the mounting piece is level with the ﬂoor.

5A

4” Minimum

5B) Use a pencil to mark the positions of the top two holes, then use the 1/4 inch drill bit to drill holes at the locations of the two marks.

5B

5C) Insert the wall anchors into the two holes, then place the two self tapping screws through the mounting piece and into the wall anchors. Skip step 6 and go directly to step 7.

5C

6) Place the mounting piece on the wall above the gang box so that the bottom centered hole on the piece overlaps the top hole on the gang box. Insert a #6-32x1 screw through the bottom centered hole and into the top hole of the gang box.

6

19

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round SlimLine Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

7) First remove the gearbox pin, then attach the power connector to the port on the movement.

1

7

2

9) Attach the clock to the mounting piece by sliding the clock back onto it. You should hear a snapping noise as the latch engages.

8) Lay any excess wiring across the strain relief base, then attach the strain relief to the clock with the two #6-19x7/16 screws. The strain relief should be tight enough to prevent the wire from sliding.

8

10) If you need to take the clock off the wall after the installation has been completed, use a ﬂat-blade screwdriver or eyeglasses screwdriver to press down on and release the mounting piece latch, then slide the clock off the mounting piece.

9

10

20

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Round Aluminum or Wood Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

Quantity

SAL or SALG round SlimLine analog clock with aluminum/ wood rim

Included in Mounting Kit (A-SLM-MK-AW-1)

Mounting Piece

Release lever

#6-19x7/16 screw

Strain Relief

2 (not used)

1 (not used)

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

2 (not used)

Picture

1

#6-19x3 /8 screw

Included in Wiring Kit (A-WK-12-1V)

#8x1.5 Self-tapping screw

Wall anchor

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

1 (not used)

2

21

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Place the ﬂat side of the mounting piece on the wall. Leave at least 4 inches between the top of the mounting piece and ceiling. Conﬁrm that the bottom of the mounting piece is level with the ﬂoor.

4” Minimum

1

2) Use a pencil to mark the positions of the two holes, then use the 1/4 inch drill bit to drill holes at the locations of the two marks.

2

3) Insert the release lever into the hole atop the mounting piece latch.

3

4) Insert the wall anchors into the two holes, then place the two self tapping screws through the mounting piece and into the wall anchors.

4

22

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Remove the back cover from the battery pack by pulling the two latches away to either side and sliding the cover out.

5

6) First remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

6

2

7) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

7

8) Attach the clock to the mounting piece by sliding the clock back onto it. You should hear a snapping noise as the latch engages.

8

23

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) Use the pencil to mark the location of the hole at the top of the release lever, and remove the clock again (see step 11). Remove the mounting piece and make a hole at the location you just marked with the 1/8 inch drill bit.

9

10) Reattach the mounting piece and clock. Place one of the self-tapping screws through the hole in the top of the release lever and into the wall.

10

11) If you need to take the clock off the wall after the installation has been completed, remove the screw from the release lever, press the release lever down, then slide the clock off the mounting piece.

11

12) If you need to take the clock off the wall after the installation has been completed AND you accidentally broke off the release lever or forgot to attach it during installation, take a thin ﬂathead screwdriver, thin ruler, or eyeglass screwdriver and insert the end between the clock and the wall. Press down on the latch until you are able to slide the clock off the mounting piece.

12

24

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Round Aluminum or Wood Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

Quantity

SAM round SlimLine analog clock with aluminum/wood rim

Included in Mounting Kit (A-SLM-MK-AW)

Mounting Piece

Release lever

#6-19x7/16 screw

Strain Relief

Included in Wiring Kit (A-WK-MTG-1V)

Power/grounding wires and connector

Picture

1

2

1

#8x1.5 Self-tapping screw

Wall anchor

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

2

1 (not used)

25

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) If you are installing a new gang box in the wall, leave at least 4 inches between the top of the gang box and ceiling. Conﬁrm that the bottom of the gang box is level with the ﬂoor.

If you are using an existing gang box, the top of the gang box must be a minimum of four inches away from the ceiling.

Ceiling

1

Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Attach the power wires from your kit to the power wires in the gang box.

• Attach the Hot wire to the connector’s black wire.

• Attach the Common wire to the connector’s white wire.

• Attach the Ground wire to the connector’s green wire.

3

4) Insert the release lever into the hole atop the mounting piece latch.

4

26

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) If you do not wish to attach the mounting piece to the gang box, proceed to step 6A. Otherwise, go to step 7.

5

6A) If you do not wish to attach the mounting piece to a gang box, place the mounting piece on the wall. Leave at least 4 inches between the middle of the mounting piece and ceiling. Conﬁrm that the bottom of the mounting piece is level with the ﬂoor.

4” Minimum

6A

6B) Use a pencil to mark the positions of the top two holes, then use the 1/4 inch drill bit to drill holes at the locations of the two marks.

6B

6C) Insert the wall anchors into the two holes, then place the two self tapping screws through the mounting piece and into the wall anchors. Skip step 7 and go directly to step 8.

6C

27

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

7) Place the mounting piece on the wall above the gang box so that the bottom centered hole on the piece overlaps the top hole on the gang box. Insert a #6-32x1 screw through the bottom centered hole and into the top hole of the gang box.

7

8) Temporarily attach the clock to the mounting piece (see step 11), use the pencil to mark the location of the hole at the top of the release lever, and remove the clock again (see step 13). Remove the mounting piece and make a hole at the location you just marked with the 1/8 inch drill bit. When ﬁnished, reattach the mounting piece.

8

9) First remove the gearbox pin, then attach the power connector to the port on the movement.

1

9

2

10) Lay any excess wiring across the strain relief base, then attach the strain relief to the clock with the two #6-19x7/16 screws. The strain relief should be tight enough to prevent the wire from sliding.

10

28

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Round Aluminum or Wood Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

11) Attach the clock to the mounting piece by sliding the clock back onto it. You should hear a snapping noise as the latch engages.

11

12) Place one of the self-tapping screws through the hole in the top of the release lever.

12

13) If you need to take the clock off the wall after the installation has been completed, remove the screw from the release lever, press the release lever down, then slide the clock off the mounting piece.

13

14) If you need to take the clock off the wall after the installation has been completed AND you accidentally broke off the release lever or forgot to attach it during installation, take a thin ﬂathead screwdriver, thin ruler, or eyeglass screwdriver and insert the end between the clock and the wall. Press down on the latch until you are able to slide the clock off the mounting piece.

14

29

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Square Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG square analog clock

Mounting Piece (already attached to

clock housing)

Included in Wiring Kit (A-WK-MTG-1)

#8x1.5 Self-tapping screw

Wall anchor

Included in Gang Box Kit (A-GB-MK-1)

Quantity

1

2

Picture

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

2 (not used)

1 (not used)

30

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Detach the housing from the back of the clock. Do this by inserting a ﬂat-blade screwdriver about 1/8 inch into each of the slot holes until the housing detaches from the clocks. You may hear a snapping noise as the latches disengage.

1

2) Release the mounting piece from the back of the housing by sliding it towards the center of the housing, then pulling it back and away from the housing.

1

Mounting piece

Housing

2

3) Place the mounting piece on the wall. Leave at least 4 inches between the top of the mounting piece and ceiling. Take care to make sure that the bottom of the mounting piece is level with the ﬂoor.

3

4” Minimum

4) Use a pencil to mark the two holes shown in the diagram below. Then use the 1/4 inch drill bit to drill holes at the marked positions.

4

31

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Insert the wall anchors into the holes, then place the self-tapping screws through the mounting piece and into the wall anchors.

5

6) Remove the back cover from the battery pack by pulling the two latches away to either side and sliding the cover out.

6

7) First remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

7

8) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

8

2

32

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) Slide the clock housing onto the mounting piece. If the housing does not slide on properly, tighten the screws that attach the mounting piece to the wall.

9

10) If you wish to prevent the clock from sliding off the mounting piece, use the small silver screw on the hole below the lower of the two #6-32x1 screws. Once the small screw is in place, test it by attempting to slide the housing up. The housing should not move.

10

11) Slide the clock back into the housing. You should hear a snapping noise as the latches reengage.

11

12) If you feel the need to take the clock off the wall after the installation has been completed, use a ﬂat-blade screwdriver to detach the housing from the back of the clock, then use a Phillip’s-head screwdriver to detach the mounting piece from the housing and gang box.

12

33

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Wall Mount Installation - Square Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG square analog clock

Mounting Piece (already attached to

clock housing)

Included in Wiring Kit (A-WK-12-1V)

Power/grounding wires

And connector

#8x1.5 Self-tapping screw

Quantity

1

(not used)

2

Picture

Wall anchor

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a single gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

2 (not used)

2

1

34

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) If you are installing a new gang box in the wall, leave at least 4 inches between the top of the gang box and ceiling. Conﬁrm that the bottom of the gang box is level with the ﬂoor.

If you are using an existing gang box, the top of the gang box must be a minimum of four inches away from the ceiling.

Ceiling

1

Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Detach the housing from the back of the clock. Do this by inserting a ﬂat-blade screwdriver about 1/8 inch into each of the slot holes until the housing detaches. You may hear a snapping noise as the latches disengage.

3

4) Release the mounting piece from the back of the housing by sliding it towards the center of the housing, then pulling it back and away from the housing.

1

4

Mounting piece

2

Housing

35

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Thread the power wires from your kit through the hole at the top of the housing followed by the mounting piece, then attach them to the wires in the gang box.

• Attach the Hot wire to the connector’s black wire.

• Attach the Common wire to the connector’s white wire.

• Attach the Ground wire to the connector’s green wire.

5

6) Attach the mounting piece to the gang box using both of the #6-32x1 screws and a Phillips-head screwdriver.

6

7) Slide the clock housing onto the mounting piece. If the housing does not slide on properly, tighten the screws that attach the mounting piece to the gang box.

7

8) If you wish to prevent the clock from sliding off the mounting piece, use the small, silver 6-19x3/8 screw on the bottom centered hole. Once the screw is in place, test it by attempting to slide the housing up. The housing should not move.

8

36

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Wall Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) First remove the gearbox pin, then attach the power connector to the port on the movement.

1

9

2

11) Slide the clock back into the housing. You should hear a snapping noise as the latches reengage.

10) Loosen the strain relief by unscrewing the two screws. Slip any excess wiring through it, then tighten the strain relief by reinserting and tightening the screws.

10

12) If you feel the need to take the clock off the wall after the installation has been completed, use a ﬂat-blade screwdriver to detach the housing from the back of the clock, then use a Phillip’s-head screwdriver to detach the mounting piece from the housing and gang box.

11

12

37

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round Standard ABS Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round Standard ABS analog clock

Included in Wiring Kit (A-WK-12-1)

Mounting Bracket

#10x1.5 Self-tapping screw

Wall anchor

#4x5/16 Screw

Quantity

1

1 (not used)

2 (not used)

1 (not used)

Picture

Bracket Securing Nut

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

1 (not used)

Continued on next page

38

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round Standard ABS Clock - Battery Powered

Included in Adapter Kit (A-MOUNT-12S-2) or (A-MOUNT-16S-2)

Description

Round Clock Adapter

Included in Pole Kit (SAB-4BD-00S-0)

Dual-mount pole, including mounting plate

#10-32x3/8 green screw

#8-32x7/16 screw

Quantity

1

8

Picture

M3.5-1.0x10 screw (black)

Internal-tooth washer

#6-32x1 screw

Adapter tab screws

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors that can support 50 lbs and a maximum screw size of 10x1.5”, four #8 screws for the wall anchors, four #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

4

8

4

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

39

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

1

2) Place the mounting plate on the wall or ceiling. If you are installing a gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

2

3) Conﬁrm that the mounting plate is level with the ﬂoor. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners of the plate.

3

4) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

4

40

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Insert the #8 screws through the mounting plate and into the anchors.

5

5B) If you are installing the clock atop an gang box, use the green screw to attach a grounding wire to the mounting plate.

5B

6) Use a screwdriver to remove one of the end caps. The end cap and screw that was used to secure it will not be needed again during this installation.

7) Insert the four #8-32x7/16 screws through the internal-tooth washers, then through the adapter, and ﬁnally into the pole. Use a screwdriver to tighten the screws so that the adapter does not move.

76

41

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Battery Powered

8) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

8

1

2

9) Remove the back cover from the battery pack by pulling the two latches away to either side and sliding the cover out.

WALL

9

CEILING

10) First remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

10

2

For instructions regarding the original battery pack and movement design, refer to the section of this manual labeled “Legacy Movement - Battery Powered”.

42

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

11) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

11

12) Slide each clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place. Insert the adapter tab screws to complete the installation.

12

13) If you feel the need to detach the clock from the housing after the installation has been completed, remove the outer adapter screws, press down on the latches, and gently pull on the rim of the clock until the clock detaches.

13

43

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round Standard ABS Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round Standard ABS analog clock

Included in Wiring Kit (A-WK-12-1V)

Mounting Bracket

Power/grounding wires and connector

Bracket securing nut

Quantity

1

1 (not used)

Picture

#10x1.5 Self-tapping screw

Wall anchor

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

2 (not used)

Continued on next page

44

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round Standard ABS Clock - Locally Powered

Included in Adapter Kit (A-MOUNT-12S-2) or (A-MOUNT-16S-2)

Description

Round Clock Adapter

Included in Pole Kit (SAB-4BD-00S-0)

Dual-mount pole, including mounting plate

#10-32x3/8 green screw

#8-32x7/16 screw

Quantity

1

8

Picture

M3.5-1.0x10 screw (black)

Internal-tooth washer

#6 -32x1 screw

Adapter tab screws

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors that can support 50 lbs and a maximum screw size of 10x1.5”, four #8 screws for the wall anchors, four #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

4

8

4

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

45

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

Ceiling

1

11” Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

3

4) Attach the mounting plate to the gang box using only two of the four long silver #6-32x1 screws. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners.

4

46

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

5

7) Thread any wiring through the mounting plate, and attach a grounding wire to the mounting plate using one of the larger centered holes and the #10-32x3/8 screw.

6) Reattach the mounting plate, this time using all four long, silver #8 screws, then insert the four #6-32x1 screws through the mounting plate and into the anchors.

6

8) Use a screwdriver to remove one of the end caps. The end cap and screw that was used to secure it will not be needed again during this installation.

7

8

47

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) Insert the four #8-32x7/16 screws through the internal-tooth washers, then through the adapter, and ﬁnally into the pole. Use a screwdriver to tighten the screws so that the adapter does not move.

9

10) Thread at least ﬁfteen inches (38.1cm) of wiring from the gang box through the bottom of the pole until each wire exits through the hole in the adapter.

10

Adapter hole

11) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

11

1

2

WALL

CEILING

48

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

12) Attach the power wires from your kit to the wires you threaded through the pole.

• Attach the Hot wire to the connector’s black wire.

• Attach the Common wire to the connector’s white wire.

• Attach the Ground wire to the connector’s green wire.

Consult the diagram on the left for additional help.

Gang

12

Box

Common

Power

Ground

Green

Black

White

CLOCK 1

Black

Green

White

13) First remove the gearbox pin, then attach the power connector to the port on the movement.

1

13

2

14) Slide the clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place. Insert the adapter tab screws to complete the installation.

14

15) If you feel the need to detach the clock from the housing after the installation has been completed, remove the outer adapter screws, press down on the latches, and gently pull on the rim of the clock until the clock detaches.

15

49

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round SlimLine

Quantity

1

analog clock

Included in Pole Kit (SAB-4BD-00S-0 or SAB-1BD-00S-0)

Dual-mount pole, including mounting plate.

#10-32x3/8 green screw

#8-32x7/16 screw

M3.5-1.0x10 screw (black)

1

8

4

Picture

Internal-tooth washer

#6 -32x1 screw

Included in Adapter Kit (A-SLM-Mount-12S-0)

Round Clock Adapter 1

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

8

4

Continued on next page

50

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

Included in Mounting Kit (A-SLM-MK-S-1) or (A-SLM-MK-AW)

Description

Mounting Piece

Release lever

#6-19x7/16 screw

Strain relief

Included in Wiring Kit (A-WK-MTG-1)

#10x1.5 Self-tapping screw

Quantity

1 (not used)

0 or 1 (not used)

2

1

2

Picture

Wall anchor

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user must also provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, two additional #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

SlimLine and Aluminum Clocks use the same installation procedures for ﬂag mount housings.

2

2 (not used)

1 (not used)

51

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

1

2) Place the mounting plate on the wall or ceiling. If you are installing a gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

2

11” Minimum

3) Conﬁrm that the mounting plate is level with the ﬂoor. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners of the plate.

3

4) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

4

52

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Insert the #8 screws through the mounting plate and into the anchors.

5

5B) If you are installing the clock atop an gang box, use the green screw to attach a grounding wire to the mounting plate.

5B

6) Use a screwdriver to remove one of the end caps. The end cap and screw that was used to secure it will not be needed again during this installation.

6

7) Insert the four #8-32x7/16 screws through the internal-tooth washers, then through the adapter, and ﬁnally into the pole. Use a screwdriver to tighten the screws so that the adapter does not move.

7

53

The Sapling Company, Inc.

1

1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

8) Thread at least ﬁfteen inches (38.1cm) of wiring from the gang box through the bottom of the pole until each wire exits through the hole in the adapter.

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

8

Adapter hole

9) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

9

1

2

WALL

1

CEILING

54

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

10) Remove the back covers from the battery pack by pulling the two latches away to either side and sliding the cover out.

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

10

11) First remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

11

2

12) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

12

55

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

13) Slide the clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place.

WALL

13 14

CEILING

14) If you feel the need to detach the clock from the housing after the installation has been completed, use a ﬂat-blade screwdriver on the four slots around the outside of the housing. You may hear a snapping noise as the internal latches disengage.

56

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round SlimLine

Quantity

1

analog clock

Included in Pole Kit (SAB-4BD-00S-0 or SAB-1BD-00S-0)

Dual-mount pole, including mounting plate.

#10-32x3/8 green screw

#8-32x7/16 screw

M3.5-1.0x10 screw (black)

Internal-tooth washer

1

8

4

8

Picture

#6-32x1 screw

Included in Adapter Kit (A-SLM-Mount-12S-0)

Round Clock Adapter 1

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

4

Continued on next page

57

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

Description

Quantity

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

2 (not used)

1 (not used)

Included in Mounting Kit (A-SLM-MK-S-1) or (A-SLM-MK-AW)

Mounting Piece

Release lever

#6-19x7/16 screw

Strain relief

1

(not used)

0 or 1 (not used)

2

1

Picture

Included in Wiring Kit (A-WK-12-1V)

Power/grounding wires

And connector

#8x1.5 Self-tapping screw

Wall anchor

PLEASE NOTE: A user must also provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, two additional #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a replacement kit.

SlimLine and Aluminum Clocks use the same installation procedures for ﬂag mount housings.

1

(not used)

2

2 (not used)

58

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall. The box should be installed level and plumb with the wall and ceiling.

Ceiling

1

11” Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

3

4) Attach the mounting plate to the gang box using only two of the four long, silver #6-32x1 screws. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners.

4

59

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

5

7) Thread any wiring through the mounting plate, and attach a grounding wire to the mounting plate using one of the larger centered holes and the #10-32x3/8 screw.

6) Reattach the mounting plate, this time using all four long, silver #6-32x1 screws, then insert the four #8 screws through the mounting plate and into the anchors.

6

8) Use a screwdriver to remove one of the end caps. The end cap and screw that was used to secure it will not be needed again during this installation.

7

8

60

The Sapling Company, Inc.

1

1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) Insert the four #8-32x7/16 screws through the internal-tooth washers, then through the adapter, and ﬁnally into the pole. Use a screwdriver to tighten the screws so that the adapter does not move.

9

10) Thread at least ﬁfteen inches (38.1cm) of wiring from the gang box through the bottom of the pole until each wire exits through the hole in the adapter.

10

Adapter hole

11) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

11

1

2

1

WALL

CEILING

61

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

12) Attach the power wires from your kit to the wires you threaded through the pole.

• Attach the Hot wire to the connector’s black wire.

• Attach the Common wire to the connector’s white wire.

• Attach the Ground wire to the connector’s green wire.

Consult the diagram on the left for additional help.

12

Gang Box

Common

Power

Ground

Green

Black

White

CLOCK 1

Black

Green

White

13) First remove the gearbox pin, then attach a power connector to the port on the side of the movement.

1

13

2

14) Lay any excess wiring across the strain relief base, then attach the strain relief to the clock with the two #6-19x7/16 screws. The strain relief should be tight enough to prevent the wire from sliding.

14

62

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

15) Slide the clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place.

WALL

15 16

CEILING

16) If you feel the need to detach the clock from the housing after the installation has been completed, use a ﬂat-blade screwdriver on the four slots around the outside of the housing. You may hear a snapping noise as the internal latches disengage.

63

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Square Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG square analog clock

Quantity

1

Included in Pole Kit (SAB-4GD-00S-0 or SAB-1GD-00S-0 )

Dual-mount pole, including mounting plate.

#8-32x7/16 screw

M3.5-1.0x10 screw (black)

Internal-tooth washer

1

8 (4 used)

4 (not used)

8 (4 used)

Picture

#10-32x3/8 green screw

#6 -32x1 screw

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

1

4

Continued on next page

64

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Battery Powered

Included in Wiring Kit (A-WK-MTG-1)

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Description

#10x1.5 Self-tapping screw

Wall anchor

Quantity

2

Picture

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, two additional #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

2 (not used)

1 (not used)

65

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

1

2) Place the mounting plate on the wall or ceiling. If you are installing a gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

2

11” Minimum

3) Conﬁrm that the mounting plate is level with the ﬂoor. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners of the plate.

3

4) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

4

66

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Insert the #8 screws through the mounting plate and into the anchors.

5

5b) If you are installing the clock atop an gang box, use the green screw to attach a grounding wire to the mounting plate.

5B

6) Detach the housing from the back of each clock. Do this by inserting a ﬂat-blade screwdriver about 1/8 inch into each of the slot holes until the piece detaches. You may hear a snapping noise as the latches disengage.

6

7) Release the mounting piece from the back of the housing by sliding it towards the center of the housing, then pulling it back and away from the housing. You will not need the mounting pieces later; either store them or throw them away at your discretion. DO NOT THROW AWAY

THE HOUSINGS.

1

7

Mounting piece

2

Housing

67

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Battery Powered

8) Attach the clock housing to the pole using four black #8-32x7/16 screws and four internal-tooth washers.

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

8

9) Attach the base of the pole to the mounting plate, so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

9

1

2

WALL

CEILING

68

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

10) Remove the back covers from the battery pack by pulling the two latches away to either side and sliding the cover out.

10

12) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

11) Remove the gearbox pin, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

11

2

12

69

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

13) Rotate the clock so that it is right-side up. Slide the clock back into its housing. You should hear a snapping noise as the latches reengage.

WALL

13 14

CEILING

14) If you feel the need to detach the clock from the housing after the installation has been completed, use a ﬂat-blade screwdriver on the four slots around the outside of the housing. You may hear a snapping noise as the internal latches disengage.

70

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Flag Mount Installation - Square Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG square analog clock

Quantity

1

Included in Pole Kit (SAB-4GD-00S-0 or SAB-1GD-00S-0 )

Dual-mount pole, including mounting plate.

#8-32x7/16 screw

M3.5-1.0x10 screw (black)

Internal-tooth washer

1

8 (4 used)

4 (not used)

8 (4 used)

Picture

#10-32x3/8 green screw

#6 -32x1 screw

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

1

2

Continued on next page

71

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Locally Powered

Included in Package

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Description

Power/grounding wires

Quantity

1

Picture

And connector

(not used)

#8x1.5 Self-tapping screw

Wall anchor

2

2 (not used)

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, two additional #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

2 (not used)

1 (not used)

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

72

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall. The box should be installed level and plumb with the wall and ceiling.

Ceiling

1

11” Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

3 4

4) Attach the mounting plate to the gang box using only two of the four long, silver #6-32x1 screws. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners.

73

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

5

7) Thread any wiring through the mounting plate, and attach a grounding wire to the mounting plate using one of the larger centered holes and the #10-32x3/8 screw.

6) Reattach the mounting plate, this time using all four long, silver #6-32x1 screws, then insert the four #8 screws through the mounting plate and into the anchors.

6

8) Detach the housing from the back of each clock. Do this by inserting a ﬂat-blade screwdriver about 1/8 inch into each of the slot holes until the piece detaches. You may hear a snapping noise as the latches disengage.

7

8

74

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) Release the mounting piece from the back of the housing by sliding it towards the center of the housing, then pulling it back and away from the housing. You will not need the mounting pieces later; either store them or throw them away at your discretion. DO NOT THROW AWAY

THE HOUSINGS.

1

9

Mounting piece

2

Housing

10) Attach the clock housing to the pole using four black #8-32x7/16 screws and four internal-tooth washers.

10

11) Thread at least ﬁfteen inches (38.1cm) of wiring from the gang box through the bottom of the pole until each wire exits through the hole in the adapter.

11

Adapter hole

75

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Locally Powered

12) Attach the base of the pole to the mounting plate, so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

12

1

2

13) Attach the power wires from your kit to the wires you threaded through the pole.

• Attach the Hot wire to the connector’s black wire.

• Attach the Common wire to the connector’s white wire.

• Attach the Ground wire to the connector’s green wire.

Consult the diagram on the left for additional help.

1

CEILINGWALL

Gang Box

13

Ground

Green

Black

White

CLOCK 1

Black

Green

White

Common

Power

76

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Flag Mount Installation - Square Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

14) First remove the gearbox pin, then attach the power connector to the port on the movement.

1

14

2

16) Rotate the clock so that it is right-side up. Slide the clock back into its housing. You should hear a snapping noise as the latches reengage.

15) Loosen the strain relief by unscrewing the two screws. Slip any excess wiring through them, then tighten the strain relief by reinserting and tightening the screws.

15

17) If you feel the need to detach the clock from the housing after the installation has been completed, use a ﬂat-blade screwdriver on the four slots around the outside of the housing. You may hear a snapping noise as the internal latches disengage.

WALL

16 17

CEILING

77

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Round Standard ABS Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round analog clock

Quantity

2

Included in Double Mount Kit (SAB-4BD-12R-0 or SAB-4BD-16R-0) (SAB-4BD-12R-0M or SAB-4BD-16R-0M)

Dual-mount pole, including mounting plate and adapters

#10-32x3/8 green screw

1

Included in Wiring Kit (A-WK-12-1)

Mounting Bracket

2 (not used)

Picture

#10x1.5 Self-tapping screw

Wall anchor

#4x5/16 Screw

Bracket Securing Nut

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors that can support 50 lbs and a maximum screw size of 10x1.5”, four #8 screws for the wall anchors, four #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

4 (not used)

2

2 (not used)

78

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

1

2) Place the mounting plate on the wall or ceiling. If you are installing a gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

2

3) Conﬁrm that the mounting plate is level with the ﬂoor. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners of the plate.

3

4) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

4

79

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Insert the #8 screws through the mounting plate and into the anchors.

5

5b) If you are installing the clock atop an gang box, use the green screw to attach a grounding wire to the mounting plate.

5B

6) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

1

2

WALL

2

6

1

CEILING

80

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Battery Powered

7) Remove the back cover from each battery pack by pulling the two latches away to either side and sliding the cover out.

For instructions regarding the original battery pack and movement design, refer to the section of this manual labeled “Legacy Movement - Battery Powered”.

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

7

8) First remove the gearbox pins, then insert the batteries into each clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

2

8

81

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9) lace the covers back onto each battery pack. You should hear a snapping noise as the latches engage.

9

10) Remove the outer adapter screws, then slide each clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place. Insert the screws again to complete the installation.

10

11) If you feel the need to detach the clock from the housing after the installation has been completed, remove the outer adapter screws, press down on the latches, and gently pull on the rim of the clock until the clock detaches.

11

82

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Round Standard ABS Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round analog clock

Quantity

2

Included in Double Mount Kit (SAB-4BD-12R-0 or SAB-4BD-16R-0) (SAB-4BD-12R-0M or SAB-4BD-16R-0M)

Dual-mount pole, including mounting plate and adapters

#10-32x3/8 green screw

1

Included in Wiring Kit (A-WK-12-1V)

Mounting Bracket

1 (not used)

Picture

Power/grounding wires and connector

Bracket securing nut

#10x1.5 Self-tapping screw

Wall anchor

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors that can support 50 lbs and a maximum screw size of 10x1.5”, four #8 screws for the wall anchors, four #6-32x1 screws for attaching the mounting plate to the gang box, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

1

1 (not used)

2

83

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

Ceiling

1

11” Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

3

4) Attach the mounting plate to the gang box using only two of the four long silver #6-32x1 screws. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners.

4

84

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

5

7) Thread any wiring through the mounting plate, and attach a grounding wire to the mounting plate using one of the larger centered holes and the #10-32x3/8 screw.

6) Reattach the mounting plate, this time using all four long, silver #8 screws, then insert the four #6-32x1 screws through the mounting plate and into the anchors.

6

8) Thread at least ﬁfteen inches (38.1cm) of wiring from the gang box through the bottom of the pole until each wire exits through the hole in the adapter.

7

8

Adapter hole

85

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Locally Powered

9) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9

1

2

WALL

10) Attach the power connectors to the wires you threaded through the pole.

• Attach the Hot wire to each connector’s black wire.

• Attach the Common wire to each connector’s white wire.

• Attach the Ground wire to each connector’s green wire.

Consult the diagram on the left for additional help.

1

CEILING

Common

Gang Box

Ground

Green

Black

White

Yellow

CLOCK 1CLOCK 2

10

BlackBlack

GreenGreen

WhiteWhite

Power

86

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round Standard ABS Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

11) First remove the gearbox pins, then attach the power connector to the port on each movement.

1

11 12

2

12) Remove the outer adapter screws, then slide each clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place. Insert the screws again to complete the installation.

13) If you feel the need to detach the clock from the housing after the installation has been completed, remove the outer adapter screws, press down on the latches, and gently pull on the rim of the clock until the clock detaches.

13

87

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round SlimLine

Quantity

2

analog clock

Included in Double Mount Kit (SAH-4BD-12R-0 or SAH-4BD-16R-0)

(SAH-1BD-12R-0 or SAH-1BD-16R-0)

Dual-mount pole, including mounting plate.

#10-32x3/8 green screw

#8-32x7/16 screw

1

8

Picture

M3.5-1.0x10 screw (black)

Internal-tooth washer

#6 -32x1 screw

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

4

8

4

Continued on next page

88

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

Included in Mounting Kits (A-SLM-MK-S-1) or (A-SLM-MK-AW)

Description

Mounting Piece

Release lever

#6-19x7/16 screw

Strain relief

Included in Wiring Kit (A-WK-MTG-1)

#10x1.5 Self-tapping screw

Quantity

2 (not used)

0 or 2 (not used)

4

2

Picture

Wall anchor

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

SlimLine and Aluminum Clocks use the same installation procedures for double mount housings.

2

4 (not used)

2 (not used)

89

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

1

2) Place the mounting plate on the wall or ceiling. If you are installing a gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall.

2

3) Conﬁrm that the mounting plate is level with the ﬂoor. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners of the plate.

3

4) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

4

90

The Sapling Company, Inc.

1

1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Insert the #8 screws through the mounting plate and into the anchors.

5

5B) If you are installing the clock atop an gang box, use the green screw to attach a grounding wire to the mounting plate.

5B

6) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

6

1

2

1

WALL

CEILING

91

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

7) Remove the back covers from the battery pack by pulling the two latches away to either side and sliding the cover out.

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

7

8) First remove the gearbox pins, then insert the batteries into the clock. If the clock is within range of a powered transmitter, the hands should begin to move within a minute.

1

8

2

9) Place the cover back onto the battery pack. You should hear a snapping noise as the latches engage.

9

92

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Battery Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

10) Slide each clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place.

10 11

11) If you feel the need to detach the clock from the housing after the installation has been completed, use a ﬂat-blade screwdriver on the four slots around the outside of the housing. You may hear a snapping noise as the internal latches disengage.

93

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG round SlimLine

Quantity

2

analog clock

Included in Double Mount Kit (SAH-4BD-12R-0 or SAH-4BD-16R-0)

(SAH-1BD-12R-0 or SAH-1BD-16R-0)

Dual-mount pole, including mounting plate.

#10-32x3/8 green screw

#8-32x7/16 screw

1

8

Picture

M3.5-1.0x10 screw (black)

Internal-tooth washer

#6 -32x1 screw

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

4

8

4

Continued on next page

94

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

Included in Mounting Kits (A-SLM-MK-S-1) or (A-SLM-MK-AW)

Description

Mounting Piece

Release lever

#6-19x7/16 screw

Strain relief

Included in Wiring Kit (A-WK-12-1V)

Power/grounding wires

And connector

Quantity

2 (not used)

0 or 2 (not used)

4

2

Picture

#8x1.5 Self-tapping screw

Wall anchor

Included in Gang Box Kit (A-GB-MK-1)

#6 -32x1 screw

#6-19x3 /8 screw

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a drill with a 1/4 inch drill bit, a pencil, a double gang box, four wall anchors (must support 50 lbs, #8 screw size, 1.5”(3.8cm) screw length), four #8 screws for the wall anchors, any equipment needed to install the gang box, and any additional wiring needed to extend the power or ground cables.

SlimLine and Aluminum Clocks use the same installation procedures for double mount housings.

(not used)

4

4 (not used)

2 (not used)

95

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

1) Install the double gang box in the wall or ceiling. If you are installing the gang box in the wall, leave at least eleven inches between the top of the gang box and the ceiling. If you are installing the gang box in the ceiling, leave at least eleven inches between the gang box and the wall. The box should be installed level and plumb with the wall and ceiling.

Ceiling

1

11” Minimum

2) Run power wiring to the gang box.

For 24V power use the ORANGE and YELLOW wires For 110V power use the BLACK and WHITE wires

CHECK YOUR WIRING

The voltage between the white and black wires should measure 105-126 volts AC in the 115 volt model, 207-253 volts AC in the 230 volt model, or 21.5-26.5 volts AC in the 24 volt model.

If you are using the 24 volt model, make sure that the wiring leading to the clock is from an ISOLATED transformer.

2

3) Detach the mounting plate from the mounting pole by unscrewing the two screws. Set the screws and pole aside for later.

3

4) Attach the mounting plate to the gang box using only two of the four long, silver #6-32x1 screws. With the mounting plate as a guide, use the pencil to trace the locations of the four larger holes at the outer corners.

4

96

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

5) Remove the mounting plate and drill the four holes that were just traced. Insert the four wall anchors into the holes.

5

7) Thread any wiring through the mounting plate, and attach a grounding wire to the mounting plate using one of the larger centered holes and the #10-32x3/8 screw.

6) Reattach the mounting plate, this time using all four long, silver #6-32x1 screws, then insert the four #8 screws through the mounting plate and into the anchors.

6

8) Thread at least ﬁfteen inches (38.1cm) of wiring from the gang box through the bottom of the pole until each wire exits through the hole in the adapter.

7

8

Adapter hole

97

The Sapling Company, Inc.

1

1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

9) Attach the base of the pole to the mounting plate so that the lip is on the top of the base, and the holes for the screws are on the bottom of the base. Hang the base on the mounting plate, attach the wires from the bottom of the pole to the wires in the gang box, then screw the other side of the base onto the mounting plate using the two black screws you set aside before.

2

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

9

1

2

WALL

10) Attach the power connectors to the wires you threaded through the pole.

• Attach the Hot wire to each connector’s black wire.

• Attach the Common wire to each connector’s white wire.

• Attach the Ground wire to each connector’s green wire.

Consult the diagram on the left for additional help.

1

CEILING

Gang Box

Common

Power

10

Ground

Green

Black

White

Yellow

CLOCK 1CLOCK 2

BlackBlack

GreenGreen

WhiteWhite

98

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

Double Mount Installation - Round SlimLine/Aluminum Clock - Locally Powered

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

11) First remove the gearbox pins, then attach a power connector to the ports on the side of each movement.

1

11 12

2

13) Slide each clock onto the adapter in the rotation that you wish it to be viewed. You should hear a snapping noise as the four clips on the adapter secure the clock in place.

12) Lay any excess wiring across the strain relief base, then attach the strain relief to the clock with the two #6-19x7/16 screws. The strain relief should be tight enough to prevent the wire from sliding.

14) If you feel the need to detach the clock from the housing after the installation has been completed, use a ﬂat-blade screwdriver on the four slots around the outside of the housing. You may hear a snapping noise as the internal latches disengage.

13 14

99

The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 USA

P. (+1) 215.322.6063 F. (+1) 215.322.8498 www.sapling-inc.com

Double Mount Installation - Square Clock - Battery Powered

VERY IMPORTANT:

INSTALL, POWER, AND SET YOUR MASTER CLOCK OR REPEATER BEFORE POWERING THE SECONDARY WIRELESS CLOCKS

A Sapling Master Clock and any Repeaters must be installed, powered, and set up BEFORE you attempt to set up a wireless clock system. If the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Included in Package

Description

SAL or SALG square analog clock

Mounting Piece-already attached

Quantity

2

(not used)

to clock housing

Included in Pole Kit (SAB-4GD-00S-0 or SAB-1GD-00S-0)

Dual-mount pole, including mounting plate.

#10-32x3/8 green screw

#8-32x7/16 screw

1

8

Picture

M3.5-1.0x10 screw (black)

Internal-tooth washer

#6 -32x1 screw

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

4

8

4

Continued on next page

100

Sapling SALG Series, SAL Series Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual