http://www.sapido.com.tw/ User Manual v1.0.0
http://www.sapido.com.tw/ User Manual v1.0.0
2
FCC Statement
Federal Communication Commission Interference Statement This equipment has been
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
1. The device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions:
2. This device may not cause harmful interference, and this device must accept any
interference received, including interference that may cause undesired operation.
3. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 centimeters between
the radiator and your body.
4. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
5. Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance20cm
between the radiator & your body.
http://www.sapido.com.tw/ User Manual v1.0.0
3
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
National Restrictions
Frequency range - 2400.0 - 2483.5 MHz
Country Country Reason/remark
Bulgaria none
General authorization required for outdoor use
and public service.
France
Outdoor use limited to 10
mW e.i.r.p. within the
band 2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4
GHz band has been ongoing in recent years to
allow current relaxed regulation. Full
implementation planned 2012.
Italy none
If used outside of own premises, general
authorization is required.
Luxembourg none
General authorization required for network and
service supply (not for spectrum).
Norway Implemented
This subsection does not apply for the
geographical area within a radius of 20 km from
the centre of Ny-Ålesund.
Russian
Federation
none Only for indoor applications.
Note: Please don’t use the product outdoors in France
CE Statement of Conform i ty
Our product has been tested in typical configuration by Ecom Sertech Corp and was found to
comply with the essential requirement of "Council Directive on the Approximation of the Laws of the
Member Sates relating to Electromagnetic Compatibility" (89/336/EEC; 92/31/EEC; 93/68/EEC).
The Declaration of Conformity can be found at the Sapido regional website. www.sapidotech.de
CE Information of Disposal
The electric and electronic equipment or unit which is labeled with crossed-out wheeled bin may not
be disposed of with household waste. This mark is based on European Directive 2002/96/EC (for
Waste Electric and Electronic Equipment=WEEE).
Please take it to the designated collection facilities. We will ensure the proper recycling, reuse and
other forms of recovery of WEEE. WEEE has the potential effects on the environment and human
health as a result of the presence of hazardous substances. You can contribute to eliminate these
effects by your cooperation.
http://www.sapido.com.tw/ User Manual v1.0.0
4
TABLE OF CONTENTS
1 GETTING TO KNOW THE SWITCH 5
1.1 Introduction 5
1.2 Key Features 5
1.3 The Front Panel 6
1.3.1 LEDs status 6
1.4 The Rear Panel 7
1.4.1 Power Connector 7
1.4.2 Network Ports 7
1.4.3 Cabling 7
1.4.4 QoS Switch 7
2 USEFUL TIPS 9
2.1 Prior to Installation 9
2.2 Half- and Full-Duplex 9
2.3 Auto-Negotiation 9
3 PRODUCT SPECIFICATIONS 11
http://www.sapido.com.tw/ User Manual v1.0.0
5
1 Getting to know the Switch
1.1 Introduction
The Fast Ethernet Switch is equipped with 5 100Mbps copper ports and each port
provides a max speed of 200Mbps and a Full-Duplex, Collision Free Bandwidth. It’s a
multi-speed, versatile network device that combines Fast Ethernet, and Ethernet ports
in a single device. This device meets RoHS compliance. It saves power with Green
Ethernet technology.
1.2 Key Features
Supports Auto-Negotiation on each TP port
Supports 2047byte maximum packet length
Supports Green Ethernet
Link-On and Cable Length Power Saving： The switch provides detection of
cable length and adjustment of power required for the detected cable length.
This feature provides high performance with minimum power consumption
Link-Down Power Saving：The switch implements link-down power saving on
a per-port basis, greatly cutting power consumption when the network cable is
disconnected greatly cutting power consumption when the network cable is
disconnected
IEEE 802.3az Energy Efficient Ethernet (EEE) supported： Energy Efficient
Ethernet (EEE) ability for 100Base-TX in full duplex operation, and supports
10Base-Te for 10Base-T in full/half duplex, which can reduce power
consumption during periods of low link utilization
Provides Store-and-Forward switching scheme
Supports Auto-MDI/MDI-X function
Supports IEEE 802.3x Flow-Control for Full-Duplex operation
Back-Pressure function supports for Half-Duplex operation
2K-entry lookup MAC address table
Loop detection：If a loop is detected, the switch will drive the external LEDs and
buzzer alarm
Supports QoS（Quality of Service）function
http://www.sapido.com.tw/ User Manual v1.0.0
6
1.3 The Front Panel
1.3.1 LEDs status
Information about the Switch’s activity is displayed through its LEDs, shown as below.
LED Function Color Status Description
Green
On
Power is being applied to this
product
Power x1
Power indication
Red
Blinking Loop detected
On Connected at 10/100Mbps
Blinking 10/100Mbps Tx/Rx activity
Port x 5
Ethernet port
activity and loop
status
Green
Blinking Loop detected
http://www.sapido.com.tw/ User Manual v1.0.0
7
1.4 The Rear Panel
1.4.1 Power Connector
The power connector is designed to be used with the power adapter included in the
product package.
1.4.2 Network Ports
The Switch is equipped with five RJ-45 ports that support network speeds of
10/100Mbps.
1.4.3 Cabling
100Mbps - To transmit at 100Mbps requires Cat. 5 cabling.
10Mbps - When transmitting at 10Mbps, Cat. 3, 4 or 5 TP cabling with RJ-45 sockets
can be used.
Port Type Cable Type Connector
100BASE-TX Cat.5 TP RJ-45
10BASE-T Cat. 3, 4 or 5 TP RJ-45
Note: Cat. 5 TP cable recommended whenever installing new cabling.
1.4.4 QoS Switch
The Switch button can setup two mode of QoS function. You must restart the power
after switch the button
Normal model
QoS Mode
Switch
DC
Input
http://www.sapido.com.tw/ User Manual v1.0.0
8
Port 1 －＞ Normal Priority ( Red )
Port 2 －＞ Normal Priority ( Yellow )
Port 3 －＞ Normal Priority ( Yellow )
Port 4 －＞ Normal Priority ( Green )
Port 5 －＞ Normal Priority ( Green )
Auto control mode
Port 1 －＞ Most High Priority ( Red )
Port 2 －＞ More High Priority ( Yellow )
Port 3 －＞ More High Priority ( Yellow )
Port 4 －＞ High Priority ( Green )
Port 5 －＞ High Priority ( Green )
http://www.sapido.com.tw/ User Manual v1.0.0
9
2 Useful Tips
2.1 Prior to Installation
Before installing the switch and connecting network devices, it is important to plan the
network's layout. Things you should consider include:
．Dedicated Bandwidth: File servers and other high-traffic hardware will have better
and improved performance if they have their own dedicated 10Mbps, or 100Mbps
bandwidth.
．Full-Duplex: Determine which devices support Full-Duplex connections.
．Fast Ethernet: Make sure rules for cable lengths and categories are followed.
．Auto-Negotiation: Devices with different speeds may be easily swapped when the
other end of the cable is fixed to a port with Auto-Negotiation.
2.2 Half- and Full-Duplex
The switch supports both Half- and Full-Duplex modes for 10BASE-T and
100BASE-TX.
．In Half-Duplex mode: Data cannot be transmitted and received at the same time.
Attached devices must finish transmitting data before they can receive data.
．In Full-Duplex mode: Data can be transmitted and received at the same time.
However:
．Full-Duplex transmission is only possible between two devices with a dedicated link
(e.g., Switch-Switch, Switch-PC)
．Both devices must have Full-Duplex capability
．Both devices must be set to Full-Duplex (e.g. Auto-Negotiation – Auto-Negotiation,
Non-Auto-Negotiation to Non-Auto-Negotiation)
The 10/100Mbps ports on the switch detect and set the line's operating mode by using
their Auto-Negotiation function.
2.3 Auto-Negotiation
Every 10/100Mbps port on the switch has a built-in "Auto-Negotiation" function. This
technology allows each port to automatically sense and set the best possible speed as
soon as a connection with another network device is established (usually at Power
“On” or Reset).
Evaluating Auto-Negotiation Capability:
if attached device is: The switch will automatically set its TP ports to operate at:
100Mbps
no Auto-Negotiation
100Mbps (100BASE-TX, Half-Duplex)
100Mbps
with Auto-Negotiation
200Mbps (100BASE-TX, Full-Duplex)
http://www.sapido.com.tw/ User Manual v1.0.0
10
10Mbps
no Auto-Negotiation
10Mbps (10BASE-T, Half-Duplex)
10Mbps
with Auto-Negotiation
20Mbps (10BASE-T, Full-Duplex)
Note: If the attached device is set to a fixed mode (ex: Forced Full-Duplex) it will not
operate as an Auto-Negotiation device.
http://www.sapido.com.tw/ User Manual v1.0.0
11
3 PRODUCT SPECIFICATIONS
Item Specification
Key Components
Chipset
Realtek RTL8305N (5-port MAC with 5-port PHY)
Ethernet Interfaces
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3x Flow Control
Ethernet Port
5 x 10Base-T/100Base-TX Ethernet ports
Supports Auto-MDI/MIDX and Auto-Negotiation
Supports 10Base-T: Category 3、4 or 5 TP
Supports 100Base-TX : Category 5 TP
Transfer Mode
Store-and-Forward
MAC Address Table
2K-entry lookup table with 4-way associative hash algorithm
Bandwidth
10BASE-T: 10/20Mbps (half/full duplex)
100BASE-TX: 100/200Mbps (half/full duplex)
Forwarding/Filtering
Rate
14881 packets/second per port @ 10Mbps maximum
148810 packets/second per port @ 100Mbps maximum
Switch Fabric
1Gbps
Jumbo Frame
Supports maximum 2047bytes packet length
Green Ethernet
Link-On and Cable Length Power Saving
Link-Down Power Saving
IEEE 802.3az Energy Efficient Ethernet (EEE)
Miscellaneous
LED Indicators
Power x 1
Port Link/Act/Loop x 5
Operation Requirement
Operating Temp. 0 to 40C (32 to 104 F)
Storage Temp. -20 to 70C (-4 to 158 F)
Operating Humidity 10% to 85% Non-Condensing
Storage Humidity 5% to 90% Non-Condensing
Power Supply
Power Adapter DC5V/0.4A
Dimensions
118(L) x 70(W) x 25(H) mm
Loading...