SANYO VPC-J4EX Service Manual 00-47
4. USB STORAGE INFORMATION REGISTRATION
USB storage data is important for when the camera is connected to a computer via a USB connection.
If there are any errors in the USB storage data, or if it has not
been saved, the USB specification conditions will not be satisfied, so always check and save the USB storage data.
Preparation:
POWER switch: ON
Adjustment method:
1. Connect the camera to a computer. (Refer to 3-5. Connecting the camera to the computer on the page 13.)
2. Double-click on the DscCalDi.exe.
3. Click on the Get button in the USB storage window and
check the USB storage data.
VID: SANYO
PID: J4
Serial:
Rev. : 1.00
4. Check the “Serial” in the above USB storage data. If the
displayed value is different from the serial number printed
on the base of the camera, enter the number on the base
of the camera. Then click the Set button.
5. Next, check VID, PID and Rev. entries in the USB storage
data. If any of them are different from the values in 3. above,
make the changes and then click the corresponding Set
button.
Calibration
AWB
Focus
UV Matrix
Cal Mode
Cal Data
USB storage
VID
Get
PID
Set
OK
OK
Upload
Firmware
Image
Initialize
EVF
LCD Type
LCD
R Bright
RGB Offset
Tint
VCO
H AFC Test
Serial
Set
Set
Rev.
B Bright
Gain
Phase
Set
Set
VCOMDC
VCOMPP
Setting
Language
Video Mode
Factory Code
– 17 –
5. TROUBLESHOOTING GUIDE
POWER LOSS INOPERTIVE
SET THE MAIN
SWITCH TO PLAY
MODE
IC301-56
(SCAN IN0)
PULSE INPUT
NO
IC302-7 4.7 V
(BOOST 4.7 V)
YES
IC301-33
(VDD)
HIGH
IC301-9
(RESET)
HIGH
IC301-13
(BAT OFF)
HIGH
IC301-8
OSCILLATION
YES
IC301-11
OSCILLATION
YES
YES
NO
LOW
LOW
LOW
NO
NO
CHECK S3001
CHECK ST1, IC955,
CHECK IC302
CHECK IC302, RB302
CHECK RB302
CHECK X3001
CHECK X3002
Q9552
TAKING INOPERATIVE
PUSH SHUTTER
BUTTON
IC301-51, 52
(SCAN IN 4, 5)
PULSE INPUT
YES
CN301-34, 35
(P ON, P(A) ON)
HIGH
SERIAL
COMMUNICATION
OK
CHECK CP1 DMA
BLOCK
NO
THE UNIT SWITCH
LOW
NG
CP1 DMA BLOCK
CHECK
CHECK
IC301, ST1
CHECK IC301,
CHECK IC301
NO PICTURE
CLK (108 MHz)
INPUT TO
IC111-11 (CLK IN 1)
OK
CLK (48 MHz)
INPUT TO
IC111-16 (CLK IN 2)
OK
IC301-37, 38
(ASIC_SO, ASIC_SI)
OK
CHECK CP1, CA1
MAIN CLOCK FOR SYSTEM OPERATION
NG
NO OPERATION IF ABSENT
CHECK X1101 OSCILLATOR AND IC111
NG
CHECK IC111 etc.
INCORRECT HANDSHAKING
NG
BETWEEN 8-BIT CPU AND ASIC
CHECK EACH INTERFACE
– 18 –
6. PARTS LIST
Parts list of optional AC adaptor :
VAR-G7C/G7E/G7EX/G7U
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
645 057 1510 CORD,POWER-1.9MK, VAR-G7U ONLY
645 002 6805 CORD,POWER-1.875MK,
VAR-G7EX ONLY
645 036 7434 CORD,POWER-1.2MK, VAR-G7E ONLY
645 065 3506 CORD,POWER-1.29MK, VAR-G7C ONLY
OR 645 068 1332 CORD,POWER-1.29MK, VAR-G7C ONLY
(VAR-G7C/U)
N.S.P.
Parts list of digital camera:
VPC-J4/J4EX/J4EXBK/J4EXOR
ACCESSORIES
1 636 076 5344 STRAP-SX713/J
2 645 067 0497 DISC,CD-ROM SSP 717 U (N.S.P)
3 645 063 5816 BATTERY, RECHARGE, LI-ION
4 645 066 1877 BATTERY CHARGER
5 645 057 1503 CORD,POWER-1.2MK,EXCEPT VPC-J4
5 645 057 1510 CORD,POWER-1.9MK,VPC-J4 ONLY
6 645 065 4831 CABLE,DSC A/V SX713
7 645 065 4848 CABLE,DSC USB,SX791
8 645 058 8082 CARD,MEMORY 16MB
OR 645 061 3357 CARD,MEMORY 16MB
OR 645 065 9423 CARD,MEMORY 16MB
9112 636 077 6579 INSTRUCTION MANUAL
CAMERA (English)
(VAR-G7E)
(VAR-G7EX)
VAR-G7
Power cord
The AC adaptor VAR-G7C/E/EX/U consists of the
adaptor (VAR-G7) and the AC power cord.
12
4
3
6
8
LOCATION PARTS NO. DESCRIPTION
N.S.P.
5
7
PACKING MATERIALS
7001 636 077 6234 CARTON CASE INNER-717/EX,
7001 636 079 7833 CARTON CASE INNER-717/EX2,
7001 636 079 7840 CARTON CASE INNER-717/EX3,
7001 636 077 6241 CARTON CASE INNER-717/U,
7002 636 078 4659 CUSHION SHEET-SX792/KRNK
7003 636 077 2854 REINFORCEMENT PAD,A-713EX
7004 636 077 6265 REINFORCEMENT PAD,B-713EX TOP
19
VPC-J4EX ONLY
VPC-J4EXBK ONLY
VPC-J4EXOR ONLY
VPC-J4 ONLY
BOTTOM
CABINET & CHASSIS PARTS 1
41
18
21
31
29
17
30
22
28
103
27
19
20
32
23
33
106
34
24
35
36
25
40
37
39
105
38
26
102
16
12
13
104
14
6
10
105
15
3
7
8
10
9
11
5
103
1
101
2
4
SX717/J Parts List-1
102
N.S.P.: Not available as service parts.
20
Loading...