Page 1
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
INSTRUCTION MANUAL
COLOR CCD CAMERA
B/W CCD CAMERA
This Instruction Manual applies to the following six models.
SURFACE TYPE
VDC-C1074VA (Color High Resolution)
VDC-C1024V (Color Standard)
VDC-M1024V (Black & White)
CONTENTS
••••
INFORMATION TO USER. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About this manual
• Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
IN-CEILING TYPE
VDC-C2074VA (Color High Resolution)
VDC-C2024V (Color Standard)
VDC-M2024V (Black & White)
INCLUDED ACCESSORY
••••
Hexagonal Wrench . . . . . . . . . . . . . . . . . . 1 pc.
Page 2
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
INFORMATION TO USER
Safety Guard
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THIS UNIT.
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
UNLESS CLOSED AND SEALED.
For customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Pour la clientèle Canadienne
Cet appareil numerique de la Classe B est conforme a la norme
NMB-003 du Canada.
This installation should be made by a qualified service person and
should conform to all local codes.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
–
Increase the separation between the equipment and receiver.
–
Connect the equipment into an outlet on a circuit different
–
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
–
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by Sanyo may
void the user’s authority to operate this camera.
English
1
Page 3
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
PRECAUTIONS
In case of problem
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
Do not open or modify
Do not open the cabinet, as it may be dangerous and cause
damage to the unit. For internal settings and repairs, consult your
dealer (or a Sanyo Authorized Service Centre).
Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a
fire, short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre). Be careful to protect the camera from rain, sea
water, etc.
Be careful when handling the unit
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, or audio speakers the magnetic field they generate will
distort the image.
Protect from humidity and dust
To prevent damage to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damage.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may rise to high levels.
Install where the temperature range will stay between –10°C and
50°C. (no condensation)
Cleaning
Dirt can be removed from the housing by wiping it with a soft cloth. To
remove stains, wipe with a soft cloth moistened with a soft detergent
solution and wrung dry, then wipe dry with a dry soft cloth.
Do not use benzine, thinners or other chemical products on the
housing, as they may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes in
contact with the housing for a long period of time, as that may
cause damage or paint peeling.
Mounting Surface
The mounting surface material must be strong enough to secure
the camera.
Plaster- board without a backing plate is not recommended.
2
English
Page 4
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
INSTALLATION
Dome assembly installation
Housing
assembly
(H)
Viewing
Window
(A)
Dome
assembly
(B)
Security
Screws (4)
Surface Type
Electrical Box
Foam Gasket
Housing
assembly
Mounting Screws (4)
Camera/VRB
assembly
72 mm φ
(D)
Video Out
Cable
(F)
Housing
assembly
In-ceiling Type
Input Power
Wires
(G)
Mounting Screws (4)
Electrical
Box
(E)
(C)
Foam
Gasket
Main unit installation
•
Preparation
Make four or more holes in the ceiling or wall for the screws that
are to be used to secure the main unit. If embedding the input
power wire and video out cable, make a hole for these cables to be
passed through also.
•
Main unit installation
Use the accessory Allen key to remove the four screws (B) that
1
are securing the dome assembly (A).
Insert the foam gasket (C) in between the housing and the
2
installation surface.
Pass the input power wire (E) and video out cable (D) through
3
the hole made for that purpose.
Align the housing assembly (F) with the screw holes that have
4
been prepared, and then secure it by tightening the four or
more screws (G) (4 mm diameter screws recommended).
Determine the lens position in accordance with the location of
5
the objects to be viewed, and then tighten it in that position.
(Refer to page 4 for lens adjustment details.)
Align the viewing window (H) with the lens position.
6
Return the dome assembly (A) to its original position and secure it.
7
*
(E) Input power wires: Dual voltage system (12 V DC or 24 V AC 60 Hz)
English
3
Page 5
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
ADJUSTMENT
These adjustments are for
color cameras.
45
36
27
18
ON
OFF
LEVEL
12345678
LINE LOCK
VIDEO OUT
LINELOCK
GND
DC IN
PUSH LOCK
• The switch positions in the above
figure are the factory presets for the
color standard model.
(For color high resolution model, the
factory setting position of MIRIS (3)
is ON.)
• B/W cameras have the same variable
resister (V. R.) for Line lock and Level
as the color cameras.
ADJUSTMENTS
FLICKERLESS ON (1/100 sec.)
FLICKERLESS OFF (1/60 sec.)
BACKLIGHT COMPENSATION OFF
BACKLIGHT COMPENSATION ON
MECHANICAL IRIS
ELECTRONIC IRIS
120 IRE USER SETTING
100 IRE SETTING
AGC 26 dB MAXIMUM
AGC 20 dB MAXIMUM
AUTO TRACKING WHITE BALANCE
AUTO WHITE BALANCE
PUSH LOCK
INDOOR (3200°K)
OUTDOOR (6500°K)
4200°K
4700°K
1234 5 678
ON
OFF
ON
OFF
DIP SWITCH
ON
OFF
ON
OFF
ON
OFF
OFF OFF OFF
OFF ON OFF
OFF ON ON
ON OFF OFF
ON ON ON
ON OFF ON
ON ON OFF
LINE LOCK Use the V. R. to adjust if the TV monitor
synchronization is unsteady.
LEVEL Use the V. R. to adjust if the backlight compensation
is set to on but compensation is still not correct.
• PUSH LOCK MODE: If the push lock switch is pressed, White Balance will be adjusted automatically.
4
English
Page 6
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
ADJUSTMENT
Lens adjustment
Gimbal Bracket
Horizontal & Vertical
Adjustment Screw
(I)
(I) Horizontal & Vertical Adjustment Screw
(J) Tilt Adjustment Screw
(K) Pan Adjustment Screw
English
Angular Limit
INPUT POWER
Camera Rotation
5
Gimbal Bracket
Tilt
Camera Lens -
Perpendicular Direction
(M) (L)
Horizontal &
Vertical
Adjustment
Tilt Adjustment Screws
Adjustment Screws
for Camera Rotation
(J)
(K)
(L) Zoom ring
To adjust the zoom, loosen the zoom ring knob and then turn the
ring to the T side (to enlarge objects) or to the W side (to reduce
objects). Then tighten the knob.
(M) Focus ring
To adjust the focus, loosen the focus ring knob, turn the focus ring
to the ∞ side or to the N side to make the adjustment, and then
tighten the knob.
Page 7
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
SPECIFICATIONS
TV format :
Scanning method :
Capturing element :
Effective picture element :
Synchronization method :
Horizontal resolution :
Video signal output :
S/N ratio :
Minimum object
illumination (50IRE)
White balance (color only):
Backlight compensation
(BLC) function
Backlight compensation
iris level adjustment:
Flickerless function: :
Gain control: :
Built-in lens: :
Manual angle of field
adjustment function
Drip prevention structure :
Compatible with NTSC TV format
525 TV lines, 60 fields/sec., 2:1 interlaced
Interline transmission method, 1/3 inch CCD
fixed capturing element
379 K (VDC-C2074VA, VDC-C1074VA)
250 K (VDC-C2024V, VDC-C1024V,
VDC-M2024V, VDC-M1024V)
Internal sync or line lock
460 TV lines (VDC-C2074VA, VDC-C1074VA)
380 TV lines (VDC-M2024V, VDC-M1024V)
330 TV lines (VDC-C2024V, VDC-C1024V)
1.0 Vp-p/75 Ω (BNC termination)
50 dB (VDC-M2024V, VDC-M1024V
48 dB (VDC-C2074VA, VDC-C1074VA,
VDC-C2024V, VDC-C1024V)
:
0.2 Lux (VDC-M2024V, VDC-M1024V)
2.0 Lux (VDC-C2024V, VDC-C1024V)
3.0 Lux (VDC-C2074VA, VDC-C1074VA)
Indoor/outdoor/push lock selectable manually
:
ON/OFF selectable manually, center focus
separate photometry method
B/W cameras: ON fixed
:
Manual V. R.
ON/OFF selectable manually
B/W cameras: None
Selectable manually
Variable focal lens F2.0 – 2.8, f= 4 – 8 mm
:
Horizontal (pan) → 360°, Vertical (tilt) → 80°
Simplified
Operating environment :
Storage environment :
Power voltage/
Power consumption
(Approx.)
Weight (Approx.) :
Dimensions :
Temperature –10° C – +50°C
Humidity 90% RH or less
Temperature –20° C – +60°C
Humidity 70% RH or less
:
12 V DC or 24 V AC/60 Hz
2.5 W (VDC-M2024V, VDC-M1024V)
3.5 W (VDC-C2024V, VDC-C1024V)
4.2 W (VDC-C2074VA, VDC-C1074VA)
1.45 kg (VDC-M1024V)
1.5 kg (VDC- C1024V, VDC- C1074VA)
1.15 Kg (VDC- M2024V)
1.2 kg (VDC- C2024V, VDC- C2074VA)
Surface type
153.5 (W) x 103.3 (H) mm, Dome 102 mm φ
6.04 (W) x 4.07 (H) inch, Dome 4.02 inch φ
In-ceiling type
153.5 (W) x 121.8 (H) mm, Dome 102 mm φ
6.04 (W) x 4.80 (H) inch, Dome 4.02 inch φ
6
English
Page 8
L5QA2/US,US2, L5QB2/US, US2, L7QA2/US, US2 GB 2002, 4, 24
COLOR VIDEO CAMERA LIMITED WARRANTY
SANYO INDUSTRIAL VIDEO
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The
names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:30 AM – 5:00 PM Pacific Time
For accessories and/or parts, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:30 AM – 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY
APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO
SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will
repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.
LABOR PARTS IMAGE DEVICE
3 YEARS 3 YEARS 3 YEARS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered,
defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from
unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect
power line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE
LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS
OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING
OUT OF OR IN CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR’S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH
DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.
Model No. _________________________________________________________________________ Serial No. _________________________________________________________________________
Date of Purchase___________________________________________________________________ Purchase Price ____________________________________________________________________
OBLIGATIONS
EXCLUSIONS
ATTENTION
(Located on back or bottom side of unit.)
Where Purchased __________________________________________________________________
1AC6P1P2547-L5QA2/US, US2, L5QB2/US, US2, L7QA2/US, US2 (0402KP-CZ)
21605 Plummer Street,
Chatsworth, California 91311
Printed in Korea
Loading...