Sanyo SMO12567V Specifications

Ordering number : ENN6905

SMO12567

VCO Module

SMO12567V

Data Communication

VCO(Voltage Controlled Oscillator) Module

Use

•

VCO(Voltage Controlled Oscillator) module for VSAT / FWA.

Package Dimensions

unit : mm

1306

[SMO12567V]

Features

•

VCO possible to finely adjust its oscillation frequency.

•

Even smaller / thinner package.

•

Low phase noise.

•

Built-in attenuator enables good load stability.

•

High reliability due to hermetic seal.

2.2

20.22

15.24

7.62

Specifications

Absolute Maximum Ratings at T a=25°C

Parameter Symbol Ratings Unit Operating Voltage V Control Voltage V Operating T emperature T opg −30 to +75 °C Storage T emperature T stg −40 to +80 °C

D C

2-M2 L=3.5

Voltage control pin terminal 0.5

Indentation Point

7.5

6.0

6.5

12.6

Output pin terminal 0.5

Supply voltage pin terminal 0.5

15 V

Electrical Characteristics at T a=25°C

Parameter Symbol Conditions

Oscillating Frequency fo VD=5V, VC=5V 12560±0.5 MHz Output Power Po VD=5V, VC=5V, f=fo 6.0 9.0 dBm Operating Current I Modulation Sensitivity fm VD=5V, VC=5±1V 1.00 1.50 MHz / V Output Power Stability ∆Pr VD=5V, VC=5±4.5V Voltage Stability ∆fV VD=5±0.1V, VC=5V Temperature Stability ∆f

Load Stability ∆fL

Phase Noise Np

*1 Reference temperature : +25°C *2 Otherwise specified DUT (Load VSWR : 1.0) is used in measurement. *3 All values above are for reference. Contact your local SANYO sales representative for your requiring specifications.

VD=5V, VC=5V, f=fo 40.0 60.0 mA

VD=5V, VC=5V, --30° C to +75°C

VD=5V, VC=5V, VSWR : 1.5 VD=5V, VC=5V, VSWR : 3.0 VD=5V, VC=5V, off-carrier : 10kHz --85 --80 VD=5V, VC=5V, off-carrier : 100kHz --102 --100

min typ max

Neither oscillation stop nor jump observed

Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications.

SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.

Ratings

Within ±1.0 Within ±0.50 Within ±3.0 Within ±1.0

MHz MHz

MHz

dBc / Hz

Unit

SANYO Electric Co.,Ltd. Semiconductor Company

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN

31901 GI IM

No.6905-1/2

SMO12567

--20

--40

--60

--80

--100

Phase Noise Characteristic

SSB Phase Noise[dBc / Hz]

--120

--140

Off-set Frequency[Hz]

12.570

12.568

12.566

12.564

12.562

12.560

12.558

12.556

Oscillation Frequency[GHz]

12.554

12.552

12.550

IT02801 IT02802

Modulation Characteristics

24681001000 10000 100000 1000000

Control V oltage[V]

2.0

1.8

1.6

1.4

1.2

1.0

0.8

0.6

0.4

0.2 0

Modulation Sensitivity[MHz / V]

Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment.

SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design.

In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law.

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.

Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use.

Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.

This catalog provides information as of March, 2001. Specifications and information herein are subject to change without notice.

No.6905-2/2