SAFETY PRECAUTIONS
SERVICE WARNING
Only qualified service technicians who are familiar with safety checks and guidelines should perform service work. Before replacing parts. disconnect power source to protect electrostatically sensitive parts. Do not attempt to modify any circuit unless so recommended by the manufacturer When servicing the receiver use an isolation transformer between the line cord and power receptacle.
SERVICING THE HIGH VOLTAGE AND CRT
Use EXTREME CAUTION when servicing the high voltage circuits. To discharge static high voltage, connect a 10K ohms resistor in series with a test lead between the receiver and CRT anode lead. DO NOT lift the CRT by the neck. Always wear shatterproof goggles when handling the CRT to protect eves in case of implosion.
X-BAY RADIATION AND HIGH VOLTAGE LIMITS
Be aware of the instructions and procedures covering X-ray radiation. In solid-state receivers and monitors, the CRT is the only potential source of X-rays, Keep an accurate high voltage meter available at all times. Check meter calibration periodically. Whenever servicing a receiver, check the high voltage at various brightness levels to be sure it is regulating properly. Keep high voltage at rated value, NO HIGHER. Excessive high voltage may cause X-ray radiation or failure of associated components. DO NOT depend on protection circuits to keep voltage at rated value. When troubleshooting a receiver with excessive high voltage, avoid close contact with the CRT. DO NOT operate the receiver longer than necessary. To locate the cause of excessive high voltage use a variable AC transformer to regulate voltage. In present receivers, many electrical and mechanical components have safety related characteristics which are not detectable by visual inspection. Such components are identified by a # on both the schematic and the parts list. For SAFETY, use only equivalent replacement parts when replacing these components.
GENERAL GUIDELINES
Perform a final SAFETY CHECK before returning receiver to customer. Check repaired area for poorly soldered connections, and check entire circuit board for solder splashes. Check inner board wiring for pinched wires or wires contacting any high wattage resistors. Check that all control knobs, shields, covers, grounds, and mounting hardware have been replaced. Be sure to replace all insulators and restore proper lead dress
| TEST JIG HOOKUP | |||||
|---|---|---|---|---|---|
| Function |
Chek-A-Color
Adapter No. |
PC Board
Plug No. |
Pin | Color | |
| CRT | B239 | K4X | 1 | Red | |
| Yoke | D4137 | 3 | Blue | ||
| Yoke Settin | g YP1 | 4 | Yellow | ||
| Comments | Focus Tap | 5 | Green | ||
SAFETY CHECKS -- FIRE AND SHOCK HAZARD
Cold Leakage Checks for Receivers with Isolated Ground
Unplug the AC cord, connect a jumper across the plug prongs, and turn the power switch on (if applicable). Use an ohmmeter to measure the resistance between the jumped AC plug and any exposed metal cabinet parts such as antenna screw heads, control shafts, or handle brackets. Exposed metal parts with a return path should measure between 1M obme and 5.2M ohms. Parts without a return path must measure infinity.
Hot Leakage Current Check
Plug the AC cord directly into an AC outlet. DO NOT use an isolation transformer Use a 1500 ohms 10W resistor in parallel with a 150F capacitor to connect between any exposed metal parts on the receiver and a good earth ground. (See figure below.) Use an AC voltmeter with at least 5000 ohms per volt sensitivity to measure the voltage across the resistor. Check all exposed metal parts and measure voltage at each point. Voltage measurements should not exceed .75VAC, 500uA. Any value exceeding this limit constitutes a potential shock hazard and must be corrected. If the AC plug is not polarized, reverse the AC plug and repeat exposed metal part voltage measurement at each point.
HIGH VOLTAGE SHUTDOWN TEST Apply 120VAC, turn the receiver on, and set all customer
controls for normal operation. Measure the voltage at TP7. Voltage should measure between 16 5V and 21 0V. If voltage exceeds this range the shut down circuit must be repaired. Momentarily connect a jumper between TP7 and the cathode of D421. The receiver should lose raster and sound. If receiver does not lose raster and sound, the shutdown circuit should be repaired. To resume normal operation, remove AC power, wait 30 seconds, and then turn the receiver on.
The listing of any available replacement part herein in no case constitutes a recommendation, warranty, or guarantee by Howard W. Sams & Company as to the quality and suitability of such replacement part. The numbers of the listed parts have been compiled from information furnished to Howard W. Sams & Company by the manufacturers of the specific type of replacement part listed.
Reproduction or use, without express permission, of editorial or pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to the use of the information contained herein.
©1999 by Howard W. Sams & Company A Bell Atlantic Company 2647 Waterfront Parkway East Drive, Suite 100 Indianapolis, IN 46214-2041
Printed in the United States of America 54321 Page 1 SET 4115
PHOTOFACT Technical Service Data
GridTrace Location Main Board ..... 3 High Voltage Shutdown Test IC Functions Important Parts Information .................................... Miscellaneous Adjustments ..... 1 Parts List ..... 4 Placement Chart Safety Precautions .................................... Schematic Component Location ..... 3 Schematic Notes .................................... Schematics Audio .................................... Power Supply ..... 2 System Control ..... 2 Television ..... 2 Test Equipment .................................... Test Jig Hookup ..... 1 Troubleshooting ..... 1 Tuner Information ....................................
For Supplier Address,
See PHOTOFACTAnnual Index
4115
Ĕ
G5G-2758G0)
SIS (
CHAS
AVM-2758G
MODEL
SANYO
SANYO Model AVM-2758G (Chassis G5G-2758G0)
Complete coverage for servicing a television receiver...
- Schematics
- Component locations
- Parts list Troubleshooting auide
Coverage includes this additional model and chassis.
MODE AVM-27585
CHASSIS G5G-2758S0
HOWARD W. SAMS & COMPANY MARCH 1999 SET 4115
99PF01469
TROUBLESHOOTING
POWER SUPPLY
Check F601. If F601 is open, check D602 thru D605, C601, C604, C605, C606, and IC601. Apply 120VAC and check for 5.0V at the emitter of Q622. If the voltage is incorrect or missing, check LF601, D621, D623, and Q622. Turn receiver on and check for 130V at pin 4 of IC601. If voltage is missing, check IC601, Q621, Q623, RL601, R601, and D602 thru D605. If 130V is present, refer to "Horizontal" section of this Troubleshooting guide.
HIGH VOLTAGE SHUTDOWN
NOTE: Care should be taken in defeating the high voltage shutdown circuit as this may cause excessive X-Ray radiation and damage to the CRT and T402. Monitor the high voltage and troubleshoot.
The high voltage from T402 is monitored and rectified by D482. Should the high voltage increase, the voltage at the cathode of D422 will also increase and trigger D422 and D421. This will cause the deflection portion of IC101 to shut down the horizontal drive signal at pin 23 of IC101, causing the receiver to lose sound and raster. To troubleshoot, remove R482 and supply 90VAC with an adjustable AC transformer. Increase voltage as necessary to isolate and repair the malfunction. Return R482 to the circuit.
Voltages Taken in Shutdown
| IC10 | 01 |
|---|---|
| Pin 23 | 0V |
| Pin 24 | 0V |
| Din 25 | 71 |
HORIZONTAL
Determine if the TV is in shutdown, refer to the "High Voltage Shutdown" section of this Troubleshooting guide. If TV is not in shutdown, inject a horizontal signal at base of Q402. If horizontal deflection is now present, check Q401, T401, and pins 19 and 23 thru 27 of IC101. If horizontal deflection is still missing, check Q402, D481, D483, D484, D486, D491, D1011, IC481, Q491, Q466, and T402. The high voltage rectifier is part of T402 and if defective will affect the performance of the horizontal circuits. Width or foldover problems may be caused by C411, C412, C416, C417, and L413 being defective.
VERTICAL
Inject a vertical signal at pin 5 of IC501. If vertical deflection is present, check pin 17 of IC101. If there is still no vertical deflection, check IC501 and the deflection yoke. Vertical linearity or foldover problems may be caused by sweep shaping and bias circuits, check C502, C503, C504, and C516.
IF AGC
Inject a video IF signal at the IF input and check for video on the CRT. If video is present, check the tuner and tuner control circuits. If video is missing on the CRT, check for a video waveform at pin 45 of IC101. If video waveform is present, refer to the "Video" section of this Troubleshooting guide. Apply AGC bias to pin 12 of IC101 and check for a video waveform at pin 45 of IC101. If video waveform is present, check pins 6, 12, and 45 of IC101. If there is no video waveform check IC101
VIDEO/CHROMA
Inject a video signal at pin 45 of IC101 and check for video on CRT. If video is present refer to the "IF AGC" section of this Troubleshooting guide. If there is no video on CRT, check for video waveform at pin 38 of IC101, if video waveform is missing, check pins 47 and 42 of IC101 and Q202. If the waveform is present at pin 38 of IC101, check for chroma waveforms at pins 28, 29, and 30 of IC101. If the proper waveforms are missing, check IC101. If the proper waveforms are present, refer to the "Raster" section of this Troubleshooting guide. Check for 3.58MHz at pin 15 of IC101.
RASTER
Check the CRT and CRT voltages. If red is missing, check pin 28 of IC101 and Q705. If green is missing, check pin 29 of IC101 and Q703. If blue is missing, check pin 30 of IC101 and Q701. If the raster has a keystone shape, check the deflection yoke. If the raster has height or width problems, refer to the "Vertical," "Horizontal," and "Power Supply" sections of this Troubleshooting guide.
AUDIO
Tune in an active station transmitting a stereo signal and check for an MTS waveform at pin 7 of IC3401. If the MTS waveform is missing, check pins 7, 49, 50, and 52 of IC101. If the waveforms is present, check for audio waveforms at pin 4 of IC001 and pin 4 of IC021. If audio waveforms are missing, check IC3401. If audio waveforms are present, check IC001, and IC021.
POWER FAILURE DETECTOR
This receiver uses a power failure detector at pin 3 of IC801, which checks for an abnormal failure of power supply circuits. If an unexpected failure is caused by any one of three conditions, the receiver will shut itself off in about 2.5 seconds to prevent damage.
The three conditions are:
- 1. Failure within the power supply.
- 2. A short circuit on the load side of the power supply.
- 3. Stoppage of horizontal oscillation caused by shutdown circuits.
The power will shut itself off within 2.5 seconds if any of these conditions remain uncorrected. To see if this circuit has been activated, check pin 3 of IC481 for a voltage of 9.0V. To reset, remove power for 10 seconds or more.
MISCELLANEOUS ADJUSTMENTS
HIGH VOLTAGE CHECK
Tune in a picture. Set brightness, color, picture, and screen control to minimum. Connect a high voltage probe to CRT anode. High voltage should measure 17.5kV to 22kV.
PURITY AND CONVERGENCE
No adjustment is recommended, the CRT has a bonded yoke.
ENTERING SERVICE MODE
Disconnect the AC power cord. While pressing the menu button on the front of the set, connect the AC power cord. Use the channel up and down buttons to select the service number. Use volume up and down buttons to change the value.
EXIT SERVICE MODE
To exit service mode, press the menu button
HORIZONTAL POSITION
Tune in a crosshatch pattern. Enter the service mode and select service number 01. Set the value for the best horizontal centering.
RF AGC DELAY
Tune in a picture. Enter the service mode and select service number 03. Set the value to a point where no snow (noise) appears in picture. Check all channels for proper operation.
VERTICAL SIZE
Tune in a crosshatch pattern. Enter the service mode and select service number 07. Set the value to achieve proper vertical size and best vertical linearity.
VERTICAL CENTERING
Tune in a crosshatch pattern. Check that the pattern is centered. If too low, install resistor R513 (470 ohms, 1W). If too high, install resistor R512 (470 ohms, 1W).
GRAY SCALE
Tune in an active channel. Enter the service mode. Set the value of service numbers 08, 09, and 10 to 0. Set the value of service numbers 11 and 12 to 55. Set screen control, color, brightness, and picture to minimum. Adjust screen control, if necessary, to obtain a barely visible horizontal line. Select service number 41. Adjust the bias levels for a white line. Select service number 40 and adjust the drive values for normal black and white picture at all brightness levels.
SUB BRIGHTNESS
Tune in a color bar pattern. Set picture and brightness to normal. Connect positive lead of a digital voltmeter to TP51 and the negative lead to TP50. Enter the service mode and select service number 25. Adjust value for 520mV ±10mV.
SUB COLOR
Tune in a picture. Set color at center of its range level. Enter the service mode and select service number 26. Set the value to achieve normal color level.
SUB TINT
Tune in a picture. Set tint at center of its range level. Enter the service mode and select service number 27. Set the value to achieve normal flesh tones.
SUB SHARPNESS
Tune in a picture. Set brightness to minimum. Set picture to maximum. Enter the service mode and select service number 28. Set the value to achieve normal contrast range.
OSD HORIZONTAL POSITION
Tune in a local channel. Enter the service mode and select service number 31. Set the value to center the menu on the screen.
VIDEO INPUT LEVEL
Connect a video signal of 1.0Vp-p to the video input jack. Set receiver to video mode. Connect scope to the base of Q202, adjust VR1023 for 2.0Vp-p ± 0.2Vp-p on the scope. Set the receiver to TV mode, and press the reset button twice on the remote control. Check brightness and contrast on all channels and readjust if needed.
SOUND
Tune in a local channel. Confirm that the voltage at pin 50 of IC101 3.85V ± 0.2V, otherwise adjust T131 for 3.85V ± 0.2V.
STEREO ADJUSTMENTS
All adjustments were made using an MTS/TV-stereo generator connected to the antenna terminal. Set customer controls for normal listening levels. Select stereo mode.
Input Level
Set generator to 1kHz audio frequency and L-R modulating signal. Connect an oscilloscope to pin 7 of IC3401. Enter service mode and select service number 32. Set the data value for 0.7Vp-p waveform.
Stereo VCO
Connect a jumper between the base of Q135 and ground. Connect a frequency counter to pin 40 of IC3401 and ground. Enter the service mode and select service number 33. Set the data value for 15.734kHz +100Hz
SAP VCO
Connect a jumper between the base of Q135 and ground. Connect a 1M ohm resistor between pin 12 of IC3401 and ground. Connect a frequency counter to pin 40 of IC3401 and ground. Enter the service mode and select service number 37. Set the data value for 78.67kHz ±500Hz.
Filter
Enter the service mode and select service number 34. Set the data value to 32.
Separation
Set generator to pilot, 300Hz audio frequency, and left modulating signal. Connect an oscilloscope to pin 25 of IC3401 and ground. Enter the service mode and select service number 35. Set the data value for minimum amplitude of the waveform. Set generator to 8kHz audio frequency. Select service number 36 and set the data value for minimum amplitude of the waveform.
MISCELLANEOUS ADJUSTMENTS continued
IC802 REPLACEMENT
Perform the following adjustments after replacing IC802. Enter the service mode, select service number 01, and set value to 13. Select service number 11, and set value to 64. Select service number 12 and set value to 64. Select service number 13 and set value to 1. Select
service number 14 and set value to 1. Select service number 21 and setvalue to 7. Select service number 26 and set value to 8. Select service number 27 and set value to 18. Select service number 29 and set value to 36. Select service number 30 and set value to 2. Select service number 31 and set value to 40. Exit service mode.
| SE | USTMENT CHART | ||||
|---|---|---|---|---|---|
|
Service
No. |
Adjustment |
Value
Range |
initial
Value |
On-Set
Value |
Notes |
| 01 | HP | 0 - 31 | 13 | 17 | H-Position (H-Centering) |
| 02 | IAS | 0, 1 | 0 | 0 | IF AGC Switch, 0 = TV (Normal), 1 = AV (IF Gain Minimum) |
| 03 | RAD | 0 - 63 | 50 | 38 | RF AGC Delay |
| 04 | PT | 0 - 127 | 64 | 34 | PLL Tuning |
| 05 | ADA | 0 - 63 | 31 | 29 | APC Detect |
| 06 | CD | 0, 1 | 0 | 0 | C-Diff |
| 07 | VS | 0 - 63 | 32 | 30 | Vertical Size |
| 08 | RB | 0 - 127 | 0 | 35 | Red Bias |
| 09 | GB | 0 - 127 | 0 | 0 | Green Bias |
| 10 | BB | 0 - 127 | 0 | ĺ | Blue Bias |
| 11 | RD | 0 - 127 | 64 | 69 | Red Drive |
| 12 | BD | 0 - 127 | 64 | 53 | Blue Drive |
| 13 | TDS | 0, 1 | 1 | 1 | Trap & D (B.P.F.) Switch, 0 = Off, 1 = On |
| 14 | AF | 0, 1 | 0 | 1 | Auto Flesh, 0 = Off, 1 = On |
| 15 | BS | 0, 1 | 0 | 0 | Black Stretch, 0 = On, 1 = Off |
| 16 | VL | 0 - 7 | 4 | 4 | Video Level |
| 17 | FL | 0 - 31 | 15 | 19 | FM Level |
| 18 | NIS | 0, 1 | 1 | 1 | Black Noise Inverter, 0 = On, 1 = Off |
| 19 | ABL | 0, 1 | 1 | 1 | ABL Defeat, 0 = On, 1 = Off |
| 20 | WP | 0, 1 | 1 | 1 | White Peak, 0 = On, 1 = Off |
| 21 | GD | 0 - 15 | 8 | 7 | Green Drive Reduction |
| 22 | VC | 0 - 7 | 0 | 0 | Vert. Comp |
| 23 | VD | 0 - 63 | 32 | 32 | Vert. DC |
| 24 | AG | 0 - 3 | 3 | 0 | AFC Gain |
| 25 | SB | 0 - 63 | 32 | 27 | Sub Brightness |
| 26 | SCO | 0 - 31 | 12 | 8 | Sub Color |
| 27 | STI | 0 - 31 | 11 | 18 | Sub Tint |
| 28 | SSH | 0 - 15 | 8 | 8 | Sub Sharpness |
| 29 | OPT | 0 - 255 | 0 | 36 | Option, data 1 should be to "36", in binary 8 bit 00100100 |
| 30 | OP2 | 0 - 255 | 0 | 2 | Option, data 2 should be to "2", in binary 8 bit 00000010 |
| 31 | HR | 0 - 63 | 47 | 40 | OSD H-Position |
| 32 | INP | 0 - 63 | 32 | 15 | Input Level |
| 33 | STE | 0 - 63 | 32 | 27 | Stereo VCO |
| 34 | FIL | 0 - 63 | 63 | 32 | Filter |
| 35 | LSP | 0 - 63 | 32 | 10 | Low Separation |
| 36 | HSP | 0 - 63 | 32 | 10 | High Separation |
| 37 | SPV | 0 - 63 | 32 | 32 | SAP VCO |
| 38 | PCO | 0 - 63 | 32 | 32 | PIP Color |
| 39 | PTI | 0 - 63 | 32 | 32 | PIP Tint |
| 40 | DRV | 0 - 127 | 55 | 69 | Red Drive, press 1 to decrease value and 3 to increase value |
| DRV | 0 - 127 | 55 | 53 | Blue Drive, press 7 to decrease value and 9 to increase value | |
| 41 | - | 0 - 127 | 0 | - | Red Bias, press 1 to decrease value and 3 to increase value |
| - | - | 0 - 127 | Õ | _ | Green Bias, press 4 to decrease value and 6 to increase value |
| - | 0 - 127 | 0 | - | Blue Bias, press 7 to decrease value and 9 to increase value | |
| ÷ 12, | Ŭ | side shas, press / to decrease value and ) to merease value |
TUNER INFORMATION
| Pin | VHF Low Band | VHF High Band | UHF Band |
|---|---|---|---|
| AGC | 5.3V | 4.7V | 4.6V |
| LOCK (NC) | 1.9V | 4.3V | 5.7V |
| ENABLE | .1V | .1V | .1V |
| CLOCK | .1V | .1V | .1V |
| DATA | 0V | 0V | 0V |
| MB | 9.0V | 9.0V | 9.0V |
| PB | 5.0V | 5.0V | 5.0V |
| TU (NC) | 0V | 0V | 0V |
| TB | 34.3V | 34.3V | 34.3V |
| IF | 0V | 0V | 0V |
TUNER TERMINAL GUIDE
SCHEMATIC NOTES
For SAFETY use only equivalent replacement part, see parts list. Circuitry not used in some versions.
- --- Circuitry used in some versions.
- ∔ Ground
- m Chassis ground
- △ Taken from common tie point
3 Schematic CIRCUITRACE ® Voltage source tie point.
A— Cabling: Heavy lines reduce use of multiple lines.
Waveforms and voltages are taken from ground, unless noted otherwise.
Waveforms taken with triggered scope and colorbar signal. Waveform voltage is peak to peak. Timebase is per division. Waveforms shown at 10 divisions. Supply voltages maintained as seen at input.
Voltages measured with digital meter and a 1000µV RF signal, with colorbar pattern, applied to antenna terminal.
Controls adjusted for normal operation. Capacitors are 50 volts or less, 5% or greater unless noted.
Electrolytic capacitors are 50 volts or less, 20% or greater unless noted.
Resistors are 1/2W or less, 5% or greater unless noted. Value in () used in some versions. Measurements with switching as shown, unless noted.
Measurements with switching as shown, unless noted. Rated voltage shown on zener diodes.
PLACEMENT CHART
IC FUNCTIONS
SANYO
·
TELEVISION SCHEMATIC continued
С
SET 4115 Page 2
D
· Т · 26 · Т · 27 · Т · · 28 · Г
F
+
ADDITIONAL SCHEMATIC
A PHOTOFACT STANDARD NOTATION SCHEMATIC WITH CIRCUITRACE® © Howard W. Same & Co. 1999
. 25
TEST EQUIPMENT
Test equipment listed by participating manufacturer illustrates typical or equivalent equipment used by Sams engineers to obtain measurements. This equipment is compatible with most types used by field service technicians.
| Equipment | Sencore No. | Equipment | Sencore No. |
|---|---|---|---|
| Oscilloscope | SC3100 | Isolation Transformer | PR570 |
| Generators | Capacitance Analyzer | LC102 | |
| RGB | CM2125 | CRT Analyzer | CR7000 |
| Multiburst Signal | VG91 | AC Leakage Tester | PR570 |
| Color Bar | VG91 | Inductance Analyzer | LC102 |
| TV Stereo | VG91 | Flyback Yoke Tester | TVA92 |
| Digital VOM | SC3100 | Field Strength Meter | SL753 |
| Frequency Meter | SC3100 | Transistor Tester | TF46 |
| Hi-Voltage Probe | HP200 | Horizontal Analyzer | HA-2500 |
| Accessory Probes | TP212 | Video Analyzer | VG91, TVA92 |
MODELS
SANYC
Α
AUDIO SCHEMATIC
в
SCHEMATIC COMPONENT LOCATION GUIDE
| I | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| A1901 | A-17 | C487 | D-13 | C3408 | B-32 | IC101 | B-3 | R101 | B-24 | R484 | D-11 | R816 | A-18 | R1909 A-18 |
| C001 | D-34 | C489 | D-11 | C3409 | B-31 | 1C101 | B-6 | R104 | B-23 | R485 | D-10 | R820 | E-18 | R3401 B-34 |
| C002 | D-35 | C491 | E-11 | C3410 | A-30 | 1C101 | D-2 | R106 | B-23 | R486 | D-11 | R821 | E-20 | R3402 R-32 |
| C002 | D 25 | C102 | C2411 | D 21 | 10101 | D-2 | D122 | D-25 | D 400 | D-11 | Duan | E-20 | R3402 B-32 | |
| 0005 | D-33 | C493 | D-9 | 0.5411 | D-31 | 1C481 | D-II | R133 | A-0 | R488 | D-10 | R822 | E-19 | R3403 B-33 |
| C006 | D-35 | C496 | D-11 | C3412 | B-31 | IC501 | D-4 | R136 | A-7 | R489 | D-11 | R823 | E-18 | R3404 B-33 |
| C007 | D-36 | C497 | D-13 | C3413 | B-33 | IC601 | C-26 | R137 | A-7 | R490 | E-11 | R826 | E-20 | R3405 B-30 |
| C008 | D-35 | C498 | D-12 | C3414 | B-30 | IC801 | B-20 | R141 | C-2 | R491 | D-9 | R827 | E-19 | R3406 B-30 |
| C017 | B-35 | C502 | D.5 | C3416 | D 22 | 10001 | D 19 | D140 | C 2 | B402 | D 10 | D020 | E 10 | R3400 D-30 |
| 0001 | D-33 | 0502 | D-5 | 03410 | D-33 | 10.002 | D-10 | K142 | C-2 | R492 | D-10 | K028 | E-19 | R3407 B-33 |
| C021 | D-33 | C503 | D-4 | C3417 | B-33 | IC3401 | A-32 | R143 | B-1 | R493 | D-9 | R831 | C-19 | R3408 B-33 |
| C022 | D-34 | C504 | D-4 | C3418 | B-34 | K1001 | B-36 | R151 | B-3 | R494 | D-9 | R833 | C-18 | R3440 A-29 |
| C023 | E-35 | C505 | D-1 | C3419 | B-33 | K1001 | C-29 | R159 | B-4 | R497 | A-16 | R835 | B-19 | R3507 D-21 |
| C026 | D-35 | C506 | D-3 | C3423 | B-32 | K1001 | C-3 | P161 | B 2 | P/08 | D 12 | Devo | DI 601 A 26 | |
| C027 | E 26 | C500 | D-5 | C2424 | D-32 | C-5 | RI01 | D-2 | R490 | D-12 | R042 | C-22 | RLOUI A-20 | |
| C027 | E-30 | 0309 | D-1 | C3424 | B-31 | L104 | B-3 | RI62 | B-2 | R499 | D-12 | R843 | C-22 | RL601 D-26 |
| C037 | C-35 | CSII | D-6 | C3426 | A-32 | L166 | B-5 | R163 | B-4 | R503 | D-3 | R844 | C-22 | SP901 D-36 |
| C041 | D-13 | C516 | D-4 | C3427 | A-33 | L203 | E-13 | R164 | B-5 | R504 | D-4 | R846 | C-21 | SP902 D-36 |
| C042 | E-34 | C601 | A-25 | C3428 | B-31 | L346 | B-7 | R166 | B-4 | R 506 | D-4 | R847 | C-21 | SW1901 B-17 |
| C101 | B-24 | C604 | A-26 | C3429 | A_33 | 1401 | P167 | B 1 | P507 | D 4 | DOVO | C 21 | SW1002 B 17 | |
| C102 | P 24 | C605 | D 16 | C2421 | A 22 |
D-4
D-6 |
R107 | D-1 | R507 | D-4 | R040 | C-21 | 3W1902 B-17 | |
| C105 | D-24 | 0005 | D-20 | C3431 | A-33 | L402 | E-3 | R108 | B-1 | R208 | D-4 | R849 | C-21 | SW1903 B-17 |
| C104 | B-23 | C606 | B- 27 | C3432 | D-31 | L413 | D-6 | R201 | B-7 | R509 | D-4 | R851 | D-21 | SW1904 B-17 |
| C106 | C-1 | C607 | C-26 | C3433 | C-31 | L801 | D-27 | R202 | B-7 | R511 | D-6 | R852 | B-19 | SW1905 B-17 |
| C131 | A-6 | C622 | D-26 | C3439 | B-32 | L821 | B-18 | R207 | B-6 | R512 | D-7 | R853 | C-18 | SW1906 C-17 |
| C133 | B-6 | C623 | D-28 | C3440 | A_30 | 1851 | D.21 | B212 | B_11 | P512 | EA | D854 | C 10 | T016 D 26 |
| C126 | A 4 | C702 | D 14 | 0101 | D-21 | D251 | 0.11 | D 517 | E-0 | N034 | C-19 | TO10 B-33 | ||
| 0100 | A-0 | 0703 | D-14 | DIOL | B-23 | 1901 | B-26 | K251 | C-II | K317 | D-5 | R820 | A-21 | 1036 C-35 |
| C138 | A-5 | C705 | D-14 | D102 | B-24 | L902 | D-6 | R252 | C-11 | R518 | D-4 | R857 | A-21 | T131 A-5 |
| C142 | B-4 | C707 | B-14 | D351 | E-1 | L1901 | B-18 | R271 | B-11 | R601 | A-26 | R858 | A-21 | T151 B-3 |
| C143 | B-2 | C708 | E-16 | D421 | D-3 | LF601 | A-25 | R272 | D-10 | R602 | B-25 | R862 | C-19 | T401 E-4 |
| C147 | D-13 | C721 | D-14 | D422 | E-3 | P$601 | A-26 | R273 | D-10 | R604 | C-26 | D963 | C-10 | T402 D 7 |
| CISI | P.2 | C801 | D 29 | D420 | E 2 | 0042 | E 24 | D276 | D-10 | C-20 | Roos | C-19 | 1402 D-7 | |
| D-3 | 0001 | D-28 | D428 | E-2 | Q043 | E-34 | R2/6 | D-10 | R605 | C-26 | R864 | C-19 | T1001 C-11 | |
| C161 | B-2 | C803 | B-12 | D429 | E-2 | Q135 | A-6 | R281 | E-1 | R606 | C-26 | R867 | D-21 | VR1023 C-5 |
| C166 | B-5 | C804 | B-12 | D466 | E-12 | Q202 | B-6 | R283 | E-1 | R607 | C-26 | R881 | D-19 | W601 A-25 |
| C201 | E-13 | C806 | D-27 | D481 | C-9 | 0342 | B-8 | R287 | A-13 | R608 | B-26 | R882 | D-19 | X141 B-1 |
| C202 | B-9 | C808 | D-20 | D482 | F-2 | 0343 | D-21 | P288 | C-14 | R600 | B-27 | D992 | E-21 | V152 A 5 |
| C208 | B 10 | C811 | A 20 | D402 | C 12 | 0271 | D-21 | R200 | D 14 | D610 | 0.27 | R003 | E-21 | AISS A-S |
| 0200 | D-10 | Con | A-20 | D403 | C-12 | 03/1 | D-17 | R289 | B-14 | ROID | C-20 | R884 | E-20 | X161 B-5 |
| C209 | B-/ | C822 | B-19 | D484 | D-11 | Q372 | D-18 | R343 | B- 7 | R621 | C-26 | R886 | E-21 | X251 B-10 |
| C211 | A-8 | C829 | C-19 | D486 | D-11 | Q401 | E-3 | R344 | D-21 | R622 | C-26 | R887 | C-21 | X401 D-2 |
| C212 | B-12 | C831 | E-19 | D487 | D-10 | Q402 | E-5 | R347 | B-8 | R623 | D-27 | R1001 | C-11 | X801 B-19 |
| C252 | B-11 | C832 | E-19 | D491 | D-12 | 0466 | E-12 | R348 | B-8 | R624 | D-26 | R1002 | D-29 | |
| C253 | B-11 | C841 | B-11 | D493 | D-12 | 0/01 | E-11 | D240 | D Q | P625 | D 26 | B1002 | C 20 | |
| 0255 | E 12 | 0942 | D-11 | D493 | D-12 | 0(91 | E-11 | K349 | D-0 | R025 | D-20 | RIOUS | C-29 | |
| C250 | E-13 | C842 | B-11 | D496 | B-18 | Q621 | D-26 | R351 | D-I | R626 | D-27 | R1004 | C-3 | |
| C272 | D-10 | C843 | B-10 | D501 | D-5 | Q622 | D-26 | R352 | D-1 | R627 | D-26 | R1006 | D-29 | |
| C331 | E-12 | C853 | C-18 | D602 | A-27 | Q623 | D-26 | R353 | E-1 | R628 | D-26 | R1007 | D-29 | |
| C332 | E-12 | C854 | C-19 | D603 | B-27 | 0701 | B-15 | R371 | E-18 | R629 | D-26 | R1008 | D-30 | |
| C343 | D-22 | C856 | D-21 | D604 | Δ_27 | 0703 | C-15 | B372 | E-18 | P701 | B 14 | P1011 | C 20 | |
| C244 | D 11 | C057 | D 21 | DCOS | D 07 | 0705 | C-15 | R372 | L-10 | R701 | D-14 | RIUII | C-29 | |
| 0244 | D-/ | D-21 | D005 | D-2/ | Q705 | A-13 | K3/3 | _D-2 | R/02 | B-14 | R1012 | C-30 | ||
| C346 | B-8 | C858 | C-20 | D621 | C-26 | Q721 | D-14 | R376 | D-19 | R703 | C-15 | R1013 | C-30 | |
| C351 | D-1 | C862 | C-20 | D622 | D-26 | Q831 | A-19 | R377 | E-18 | R704 | C-14 | R1015 | C-13 | |
| C352 | D-1 | C866 | D-19 | D623 | D-27 | .0881 | E-19 | R400 | C-12 | R705 | C-14 | R1016 | C-3 | |
| C371 | D-2 | C1002 | C-11 | D721 | E-14 | 0882 | E-19 | R401 | C-12 | R706 | D-15 | R1017 | C-3 | |
| C401 | B-12 | C1003 | C-13 | D722 | E-14 | 0001 | P 16 | B402 | D 12 | B707 | D-13 | D1010 | C-5 | |
| C402 | C 12 | 01005 | D 20 | D001 | D-14 | 01001 | D-10 | R402 | D-12 | K/0/ | A-14 | RIUIS | 0-3 | |
| C403 | C-12 | C1006 | D-29 | D801 | B-19 | QIOOI | D-30 | R403 | B-13 | R708 | A-14 | R1020 | D-31 | |
| C404 | E-3 | C1007 | C-29 | D802 | B-19 | Q1002 | C-30 | R404 | E-3 | R709 | B-15 | R1022 | D-31 | |
| C405 | B-12 | C1008 | C-3 | D803 | B-18 | Q1003 | C-3 | R406 | E-4 | R711 | A-15 | R1023 | C-30 | |
| C406 | E-4 | C1020 | D-31 | D831 | A-19 | 01021 | C-5 | R407 | F -4 | R712 | C-15 | R1026 | D-31 | |
| C407 | E-4 | C1022 | F_12 | D83/ | C-19 | 01022 | C 5 | D 400 | D712 | D 12 | D1027 | 0-31 | ||
| 0409 | E-4 | 01022 | E-13 | D034 | C-10 | 01022 | C-5 | R409 | E-3 | R/13 | B-15 | RI027 | C-31 | |
| C408 | E-4 | C1023 | E-13 | D836 | C-18 | ROOT | D-34 | R413 | E-7 | R715 | B-15 | R1031 | C-4 | |
| C411 | E-6 | C1031 | C-4 | D843 | C-19 | R002 | D-34 | R418 | D-6 | R716 | C-15 | R1032 | C-4 | |
| C412 | E-6 | C1033 | B-6 | D1001 | C-30 | R003 | D-36 | R421 | E-2 | R717 | A-15 | R1033 | C-4 | |
| C416 | E-6 | C1901 | C-17 | D1003 | C-3 | R017 | B-35 | R422 | F-3 | R722 | F-14 | R1034 | C-6 | |
| C417 | E 6 | C1002 | R.17 | D1011 | CII | DO1 | D 24 | D 422 | D-3 | D702 | D-14 | D1007 | 0.0 | |
| 0417 | D-0 | 02400 | D-17 | Dioli | 0.10 | R021 | D-34 | R423 | D-2 | K/23 | D-14 | K1037 | C-5 | |
| C421 | D-2 | C3400 | E-12 | D1012 | C-12 | R022 | D-34 | R426 | D-3 | R724 | D-14 | R1901 | B-18 | |
| C422 | D-7 | C3401 | E-12 | D1901 | C-17 | R023 | D-36 | R428 | E-2 | R803 | A-12 | R1902 | B-18 | |
| C426 | D-2 | C3402 | B-32 | F601 | A-25 | R035 | E-21 | R466 | E-11 | R804 | A-13 | R1903 | B-17 | |
| C468 | E-11 | C3403 | A-31 | IC001 | C-35 | R037 | C-35 | R469 | E-11 | R807 | D-19 | R1004 | B-17 | |
| C482 | C3404 | B-24 | 10021 | D 25 | R041 | D 25 | D / 01 | D000 | D-17 | D1007 | D-17 | |||
| C402 | 0.10 | 02404 | D-34 | 10101 | D-35 | D041 | D-33 | R401 | C-9 | Rous | D-19 | K1905 | B-17 | |
| 0483 | C-28 | 03400 | D-34 | A-6 | K042 | E-35 | K482 | E-2 | K813 | A-19 | R1906 | B-17 | ||
| C484 | E-2 | C3407 | B-29 | IC101 | B-10 | | R043 | E-34 | R483 | C-11 | R814 | A-19 | R1907 | B-17 | |
| 1 | I | I | I | l . | 1 |
Important Parts Information
- The parts listed here are those not usually available from a well-stocked supply cabinet or bin.
- Where items may be replaced with equivalent parts, several alternates are shown from participating vendors.
- On the parts lists. safetv items are marked with a # to remind you that only exact replacements are recommended for these items
- When ordering parts, state the model number, part number, and description.
Obtaining Parts
Many of these parts are available from your local Sams authorized distributor or the manufacturer of the equipment. Call Sams for the name of your nearest distributor:
800-428-7267
Or consult the Sams Annual Index for the address of the original equipment manufacturer
Participating Vendors
Information on test equipment and replacement parts is listed in these pages for the following participating vendors Consult the Sams Annual Index for their current address.
- Custom Components Corporation (Chek-A-Color)
- Sencore Inc.
NTE Electronics, Inc. (NTE)
Thomson Consumer Electronics. Inc. (SK, TCE)
Terrell & Nobis (TNI Electronics)
MAIN BOARD - TOP VIEW. GRIDTRACE LOCATION GUIDE A101 C605 1-8 D621 F-4 01022 K- 7 R622 G-5 | TP51 M-15 A 1001 A-2 C606 K-9 D622 F-5 Q102 K-1 R624 G-6 VR1023 C001 K-1 C607 г-5 H-7 E-16 D623 R017 R625 G-7 X141 C001 C622 H-6 D801 н-/ H-8 L-2 R021 R626 G-6 X153 C006 M-2 C623 H_7 D802 M-10 R021 R628 G-7 X161 C-6 C007 M-2 C806 B-14 D802 L-10 R043 K-2 R803 B-6 X251 D-8 C017 M-2 C800 D803 C-14 R101 X401 1-3 DOUT B-6 D-6 C021 J-1 C822 D834 C-16 R104 I-3 I-3 R 807 C-18 X 801 B-15 C021 C829 B-18 D836 D-14 R106 H-14 R 808 C-18 M-3 C831 C-18 D843 B-17 R150 B-5 R800 C027 M-3 C832 D1001 L-6 D822 L-4 C853 A-15 D1001 L-8 R167 C-15 R827 C-18 C041 M-1 C856 A-16 D1011 M-9 R201 B-6 R828 C041 C1002 M-9 D1012 M-9 R202 Б-0 В-7 R833 I-10 C101 G-1 C1003 D1901 A-3 R212 R843 C104 C1006 F601 I-4 R 349 C-10 R844 C106 C1007 1001 L-2 R342 G-12 R044 C1008 L-9 1C001 R400 R848 D-7 C136 C1000 IC101 D-5 R400 G-14 R849 D-6 C1020 K-7 1C481 K-10 R402 F-7 R851 E-5 C1023 K-8 IC501 H-10 R404 R881 F-2 B-5 C1031 K-8 1C601 G-13 R406 R882 E-2 C201 C1033 F-5 IC801 B-17 R400 R002 E-2 C208 C1901 B-19 IC802 R409 E-8 R884 E-2 C-8 C1902 A-3 IC3401 C-3 | R413 G-19 R1001 M-9 C-7 | C3401 K1001 M-6 R418 R1020 K-5 D-6 C3401 M-12 B-3 KB R421 M-13 R1022 K-6 E-6 C3404 KD R422 R1023 E-7 C3406 B-3 KS C-8 R423 R1026 B-8 C3407 B-3 KSP R423 N-13 R1027 C-13 C3409 C-2 KTP H-1 R420 L-10 R1021 L-8 C3411 B-2 KX R469 R1034 K-7 D 8 | C3411 L 164 C-5 L-14 R1901 C401 E-6 C3413 B-2 L166 R482 R1902 C401 D-7 C3413 L203 B-8 R483 K-14 R1903 A-5 C405 C3416 B-2 L346 R484 M.14 R1904 C405 G-15 C3417 B-1 I 401 R486 J-11 R1005 H-16 C407 G-15 C3418 B-1 1 402 H-16 R488 N-11 R1906 A-0 C408 G-16 C3410 L402 G-18 R489 M-11 R1907 I-18 C3424 L801 C-17 R409 D-1 R1909 I-19 C3424 D-2 L821 R491 R3401 B-3 G-17 C3432 D-2 L851 B-16 R492 N-14 R3402 C417 G-16 C3433 D-2 L1901 R493 M-15 R3402 C421 F-8 C3439 D-3 L F601 I-5 R493 M-14 R3404 M-19 D101 G-3 PS601 I-6 R497 M-14 R3405 B-2 G-2 0043 L-3 R498 C482 L-14 D351 E-7 0135 D-4 R499 H-8 R3407 C482 I-15 D421 Q202 B-6 R503 G-9 R3408 B-1 C484 N-13 D422 N-12 0342 C-10 R 504 H-11 R3507 C487 L-14 D428 0343 RL601 G-5 C489 M-12 D429 N-13 0371 E-8 R507 H-11 SW1901 A-4 C491 L-12 D429 0372 E-8 R508 H-11 SW1902 A-5 C493 D481 L-14 0401 G-14 R 509 H-11 SW1903 A-7 C496 D482 M-13 0402 I-16 R511 SW1904 C497 D483 J-14 0466 L-10 R517 G-10 SW1905 C498 J-10 D484 L-13 0491 L-13 | R518 H-10 SW1906 A-11 C502 G-9 D486 N-11 0621 H-7 R601 I-6 T016 M-4 C502 H-11 I-0 I-8 D487 M-14 0622 G-6 R602 T036 L-4 C504 H-12 D491 M-10 Q623 R604 E-15 T131 C-4 C505 E-6 D493 H-8 0831 B-14 R605 T151 C506 H-9 D496 L-10 0881 B-19 R606 G-15 T401 C509 E-6 D501 H-9 0 882 C-18 R607 T402 I-14 D602 H-7 01001 R608 D-18 T1001 M-9 H-10 D603 J-8 Q1002 R609 TE7 C601 I-4 D604 Q1003 L-9 TP7 E-14 N-13 I-4 D605 C604 J-8 01021 K-8 R621 H-4 TP50 N-15
MAIN BOARD - TOP VIEW
SET 4115 Page 3
MAIN BOARD - BOTTOM VIEW, GRIDTRACE LOCATION GUIDE L-16 C857 L-17 C858 L-18 C862 G-17 C866 C-15 C3400 D-15 C3403 D-14 C3408 A-4 | R143 B-5 | R159 C-5 | R162 C-5 | R163 D-14 | R372 B-15 | R373 E-12 | R863 D-12 | R864 E-12 | R867 A-7 A-/ C-5 B-4 C002 C008 C022 B-15 | R3/3 D-14 | R376 B-14 | R370 R886 Б-4 С-4 С-4 C-5 R163 C-17 R164 D-17 R166 C-18 R168 C-18 R207 Б-14 С-14 R403 R887 C133 C138 C143 B-15 R403 R1002 L-14 K-13 R420 R1002 D-14 C3410 C-14 R623 H-13 R1003 M-12 C166 C3423 D-18 R251 R627 H-13 R1004 L-14 C-15 C-14 C-11 C-7 C-10 C-14 D-18 R251 D-18 R252 D-18 R271 D-18 R272 D-18 R273 C-18 R264 L-16 R281 M-18 R283 L-18 R287 M-17 R288 C202 C3425 E-14 E-14 R813 R1000 L-14 C202 C3420 E-14 B-12 R813 R1007 C3427 R816 R1011 C3/31 R010 D-18 R1011 C344 C3440 B-12 R821 B-3 C346 D002 R826 R1015 C352 R002 R831 R1015 C352 F-12 D-13 R003 R831 R835 R842 C-4 B-3 R1017 C404 R022 M-17 R288 B-4 R289 L-18 R343 L-17 R344 C-16 R347 E-16 R348 E-16 R351 D-15 R352 D-15 R371 C426 D-13 C-2 C-14 C-14 R023 R842 R846 C-3 C-3 B-3 B-5 B-5 C803 R041 R852 C803 R041 D-7 R853 R1033 K-12 C804 B-12 B-12 R133 C-10 R854 R3440 C-18 C841 R135 C-10 R856 B-5 B-4 C841 B-12 B-13 R130 C-10 R850 C-12 R857 C-12 R858 E-12 R858 C842 B-13 R137 B-13 R141 B-13 | R141 B-5 | R142 C854
MODEL AVM-2758G (CHASSIS G5G-2758G0
MAIN BOARD - BOTTOM VIEW
PARTS LIST
SEMICONDUCTORS continued
(Select the replacement that gives the best results.)
| Item No. | Туре No. | Mfr. Part No. | NTE Part No. | TCE Part No. |
|---|---|---|---|---|
| D622 | DS442X | 407 005 4505 | NTE519 | SK 3100 |
| 1N4148 | 407 008 2406 | NTE519 | SK3100 | |
| 1 SS 133 | 407 012 4406 | NTE519 | SK3100 | |
| 1 S 2076 | 407 013 4207 | NTE177 | SK9091 | |
| 1$2473 | 407 013 7109 | NTE177 | SK9091 | |
| D623 | MTZJ5.1A | 407 063 8606 | - | - |
| RD5.1EB3 | 407 056 8200 | NTE5010A | SK5A1 | |
| D721, 22 | D$442X | 407 005 4505 | NTE519 | SK3100 |
| 1N4148 | 407 008 2406 | NTE519 | SK3100 | |
| 1 SS 133 | 407 012 4406 | NTE519 | SK3100 | |
| 1 S 2076 | 407 013 4207 | NTE177 | SK9091 | |
| 1S2473 | 407 013 7109 | NTE177 | SK9091 | |
| D801, 02, 03 | DS442X | 407 005 4505 | NTE519 | SK3100 |
| 1N4148 | 407 008 2406 | NTE519 | SK3100 | |
| 1SS133 | 407 012 4406 | NTE519 | SK3100 | |
| 1S2076 | 407 013 4207 | NTE177 | SK9091 | |
| 1S2473 | 407 013 7109 | NTE177 | SK9091 | |
| D831 | RD4.3EB2 | 407 056 4707 | NTE5008A | SK4A3 |
| MTZJ3.6B | 407 065 1308 | - | - | |
| D834 | RD18EB1 | 407 054 8301 | NTE5027A | SK18A |
| MTZJ18A | 407 099 7505 | - | - | |
| D836, 43 | DS442X | 407 005 4505 | NTE519 | SK3100 |
| 1N4148 | 407 008 2406 | NTE519 | SK3100 | |
| 1SS133 | 407 012 4406 | NTE519 | SK3100 | |
| 1S2076 | 407 013 4207 | NTE177 | SK9091 | |
| 1 S 2473 | 407 013 7109 | NTE177 | SK9091 | |
| # D1001 | PC817 | - | NTE3098 | SK9763 |
| PC827C | 407 145 3703 | - | - | |
| TLP521-2-BL | 407 176 6209 | - | - | |
| PC827D | 407 176 6100 | - | - | |
| # D1003 | PC917XS | 407 205 1601 | - | - |
| D1011 | ES1 | 407-007-6606 | NTE552 | SK9000 |
| RMPG06G | 407-124-5506 | NTE552 | SK9000 | |
| D1012 | MTZJ12C | 407 063 8408 | - | - |
| D1901 | MTZJ5.1A | 407 063 8606 | - | - |
| IC001, 021 | TDA7231A | 409 343 0409 | - | - |
| # IC101 | LA76170 | 409 412 7407 | - | - |
| IC481 | BA178M09T | 409 367 2809 | NTE1966 | - |
| MC78M09CT | 409 370 0007 | - | - | |
| UPC78M09AHF | 409 366 7904 | - | - | |
| # IC501 | LA7841 | 409 340 1904 | - | - |
| # IC601 | STR30130 | 409 243 0806 | NTE1777 | SK9870 |
| IC801 | M37272M6-300SP | - | - | - |
| M37272M8-SP | 410 299 0207 | - | - | |
| IC802 | 24LC01B/P | 409 333 3700 | - | - |
| ST24C02B6 | 409 376 1503 | - | - | |
| IC3401 | UPC1851CU | 409 392 2805 | - | - |
| # For SAFETY u | se only equivalent replacem | ent part. |
| SEMICO | NDUCTORS | ||||
|---|---|---|---|---|---|
| (Select the replacement | nt that gives the best results.) | ||||
| Item No. | Type No. | Mfr. Part No. | NTE Part No. | TCE Part No. | |
| D101 | RD36EB1 | 407 056 2307 | NTE5037A | SK36A | |
| MTZJ36A | 407 100 0204 | - | - | ||
| D102 | RD5.1EB2 | 407 056 8002 | NTE5010A | SK5A1 | |
| MTZJ5.1A | 407 063 8606 | - | - | ||
| MTZJ5.1B | 407 099 5204 | - | - | ||
| RD5.1EB3 | 407 056 8200 | NTE5010A | SK5A1 | ||
| D351 | RD12EB2 | 407 054 3207 | NTE5021T1 | SK9971 | |
| MTZJ12B | 407 099 6607 | - | - | ||
| MTZJI2C | 407 063 8408 | - | - | ||
| RDI2EB3 | 407 054 3306 | NIE502IA | SKIZA | ||
| # | D421, 22 | HZIIB2L | 407 158 1307 | NTE5020A | SKIIA |
| D428 | KDISEBI | 407 054 5706 | NTESU23A | 5K 14A | |
| D 400 | 407 099 6904 |
-
NTE510 |
-
SK2100 |
||
| D429 | DS442X | 407 005 4505 | NIE519 | SK3100 | |
| 100122 | 407 008 2406 | NIE519 | SK3100 | ||
| 188133 | 407 012 4406 | NIESI9 | SK3100 | ||
| 152070 | 407 013 4207 | SK9091 | |||
| D466 |
152473
PD10EP2 |
407 013 7109 | SK9091 | ||
| D400 | MT7110P | 407 004 0008 | NIEJUIJA | SKIUA | |
| D481 | 407 099 0102 |
-
NTE552 |
- | ||
| D401 |
EKA18-04
FS1 |
407-007-6606 | NTE552 | SK9000 | |
| RMPG06G | 407-124-5506 | NTE552 | SKOOOO | ||
| D482 | TVR1G | 407 011 4407 | NTE552 | SK9000 | |
| D483 | FRA18-04 | 407-124-6404 | NTE552 | SK9000 | |
| D +05 | ES1 | 407-007-6606 | NTE552 | SK9000 | |
| RMPG06G | 407-124-5506 | NTE552 | SK9000 | ||
| D484, 86 | EU2 | 407 007 7603 | NTE552 | SK9000 | |
| ERB44-04 | 407 006 4108 | NTE552 | SK9000 | ||
| D487, 91 | ERA15-02 | 407 005 8602 | NTE552 | SK9000 | |
| MPG06D | 407 088 6502 | NTE552 | SK9000 | ||
| S5277B | 407 011 3004 | NTE552 | SK9000 | ||
| 1N4002ID | 408 009 9404 | NTE116 | SK3311 | ||
| D493 | RD7.5EB3 | 407 057 6502 | NTE5015A | SK7A5 | |
| MTZJ7.5C | 407 063 9306 | - | - | ||
| D496 | DS442X | 407 005 4505 | NTE519 | SK3100 | |
| 1N4148 | 407 008 2406 | NTE519 | SK3100 | ||
| 1SS133 | 407 012 4406 | NTE519 | SK3100 | ||
| 1S2076 | 407 013 4207 | NTE177 | SK9091 | ||
| 1$2473 | 407 013 7109 | NTE177 | SK9091 | ||
| D501 | ERA15-02 | 407 005 8602 | NTE552 | SK9000 | |
| MPG06D | 407 088 6502 | NTE552 | SK9000 | ||
| S5277B | 407 011 3004 | NTE552 | SK9000 | ||
| 1N4002ID | 408 009 9404 | NTE116 | SK3311 | ||
| # | D602 Thru | a | |||
| # | D605 | EM2B | 407 005 7605 | NTE125 | SK3081 |
| GPISG | 407 008 8606 | NTE125 | SK3081 | ||
| D (al | IS1887A | 407 013 3200 | NTE552 | SK9000 | |
| # | D621 | EKA15-02 | 407 005 8602 | NTE552 | SK9000 |
| MPG06D | 407 088 6502 | NTE552 | SK9000 | ||
| $5277B | 407 011 3004 | NTE552 | SK9000 | ||
| IN4002ID | 408 009 9404 | NTE116 | SK3311 | ||
| # | For SAFETV up a | nly aquivalant vanla coment - | and the second | ||
| # | FUT SAFELI USE 0 | my equivalent replacement p | ai L |
PARTS LIST continued
SEMICONDUCTORS continued
(Select the replacement that gives the best results.)
| Item No. | Type No. | Mfr. Part No. | NTE Part No. | TCE Part No. | |
|---|---|---|---|---|---|
| Q043, 135, 202 | 2SC1815-GR | 405 012 2002 | NTE85 | SK3124A | |
| 2SC1740S-Q | 405 011 8401 | NTE85 | SK3122 | ||
| 2SC1740S-R | 405 011 8500 | NTE85 | SK3122 | ||
| 2SC1740S-S | 405 011 8609 | NTE85 | SK3122 | ||
| 2SC1815-0 | 405 012 2101 | NTE85 | SK3124A | ||
| 2SC1815-Y | 405 012 2309 | NTE85 | SK3124A | ||
| 2SC945A-PA | 405 020 7501 | NTE85 | SK3124A | ||
| 2SC945A-QA | 405 020 7709 | NTE85 | SK3124A | ||
| 2SC945A-RA | 405 020 7907 | NTE85 | SK3124A | ||
| Q342, 43 | 2SC1815-GR | 405 012 2002 | NTE85 | SK3124A | |
| 2SC1740S-Q | 405 011 8401 | NTE85 | SK3122 | ||
| 2SC1740S-R | 405 011 8500 | NTE85 | SK3122 | ||
| 2SC1740S-S | 405 011 8609 | NTE85 | SK3122 | ||
| 2SC1815-O | 405 012 2101 | NTE85 | SK3124A | ||
| 2SC1815-Y | 405 012 2309 | NTE85 | SK3124A | ||
| 2SC945A-PA | 405 020 7501 | NTE85 | SK3124A | ||
| 2SC945A-QA | 405 020 7709 | NTE85 | SK3124A | ||
| 2SC945A-RA | 405 020 7907 | NTE85 | SK3124A | ||
| Q371, 72 | 2SA1015-Y(SAN) | 405 001 7605 | NTE290A | SK9132 | |
| 2SA1015-GR(SAN) | 406 000 6804 | NTE290A | SK9132 | ||
| 2SA1015-O(SAN) | 405 001 7407 | NTE290A | SK9132 | ||
| 2SA564A-Q(CU) | 405 004 3109 | NTE290A | SK3932 | ||
| 2SA564A-R(CU) | 405 004 3208 | NTE290A | SK3932 | ||
| 2$A933$-Q | 405 006 1707 | NTE290A | SK9132 | ||
| 0.101 | 2SA933S-R | 405 006 1806 | NTE290A | SK9132 | |
| Q401 | 2SC2271-D | 405 029 7106 | NTE399 | SK9352 | |
| 2SC2271-D-CTV | 405 013 6207 | NTE399 | SK9352 | ||
| 2SC2271-E | 405 029 7205 | NTE399 | SK9352 | ||
| ш | 0.400 | 2SC2271-E-CTV | 405 013 6306 | NTE399 | SK9352 |
| # | Q402 | 25D18/9-C1V-YB | 405 082 2407 | NTE2331 | SK10088 |
| Q400, 91 | 25D400-E-MP | 405 023 5009 | NTE382 | SK3849 | |
| 0621 22 | 25D400-F-MP | 405 012 2002 | NTE95 | SK3849 | |
| Q021, 22 | 25017405 0 | 405 012 2002 | NTE85 | SK3124A | |
| 25C17405-Q | 405 011 8500 | NTE95 | SK3122 | ||
| 25C17405-K | 405 011 8500 | INTEOS |
SK3122
SK2122 |
||
| 2SC1815-0 | 405 012 2101 | NTE85 |
SK3122
SK2124A |
||
| 2SC1815-V | 405 012 2309 | NTE85 | SK3124A | ||
| 2SC945A-PA | 405 020 7501 | NTE85 | SK3124A | ||
| 250945A-0A | 405 020 7709 | NTE85 | SK3124A | ||
| 2SC945A-RA | 405 020 7907 | NTE85 | SK3124A | ||
| 0623 | 2SA1015-GR(SAN) | 406 000 6804 | NTE2904 | SK9132 | |
| 2SA1015-O(SAN) | 405 001 7407 | NTE290A | SK9132 | ||
| 2SA1015-Y(SAN) | 405 001 7605 | NTE290A | SK9132 | ||
| 2SA564A-O(CU) | 405 004 3109 | NTE290A | SK3932 | ||
| 2SA564A-R(CU) | 405 004 3208 | NTE290A | SK3932 | ||
| 2SA933S-O | 405 006 1707 | NTE290A | SK9132 | ||
| 2SA933S-R | 405 006 1806 | NTE290A | SK9132 | ||
| Q701, 03, 05 | 2SC2621-E-RA | 405 041 6705 | NTE157 | SK3747 | |
| 2SC3620(LB-SAN-1) | 406 000 3605 | NTE157 | SK3747 | ||
| 2SC2621-C-RA | 405 066 4304 | NTE157 | SK3747 | ||
| 2SC2621-D-RA | 405 041 6507 | NTE157 | SK3747 | ||
| 2SC2688(1)-K | 405 066 9903 | NTE157 | SK3747 | ||
| 2SC2688(1)-L | 405 067 0008 | NTE157 | SK3747 | ||
| 2SC2688(1)-M | 405 067 0107 | NTE157 | SK3747 | ||
| (Select the replacement that gives the best results.) | ||||||
|---|---|---|---|---|---|---|
| Item No. | Туре No. | Mfr. Part No. | NTE Part No. | TCE Part N | ||
| Q721 | 2SA1015-Y(SAN) | 405 001 7605 | NTE290A | SK9132 | ||
| 2SA1015-GR(SAN) | 406 000 6804 | NTE290A | SK9132 | |||
| 2SA1015-O(SAN) | 405 001 7407 | NTE290A | SK9132 | |||
| 2SA564A-Q(CU) | 405 004 3109 | NTE290A | SK3932 | |||
| 2SA564A-R(CU) | 405 004 3208 | NTE290A | SK3932 | |||
| 2SA933S-Q | 405 006 1707 | NTE290A | SK9132 | |||
| 2SA933S-R | 405 006 1806 | NTE290A | SK9132 | |||
| Q831 | 2SA1015-Y(SAN) | 405 001 7605 | NTE290A | SK9132 | ||
| 2SA1015-GR(SAN) | 406 000 6804 | NTE290A | SK9132 | |||
| 2SA1015-O(SAN) | 405 001 7407 | NTE290A | SK9132 | |||
| 2SA564A-Q(CU) | 405 004 3109 | NTE290A | SK3932 | |||
| 2SA564A-R(CU) | 405 004 3208 | NTE290A | SK3932 | |||
| 2SA933S-Q | 405 006 1707 | NTE290A | SK9132 | |||
| 2SA933S-R | 405 006 1806 | NTE290A | SK9132 | |||
| Q881, 82 | 2SC1815-GR | 405 012 2002 | NTE85 | SK3124A | ||
| ` | 2SC1740S-Q | 405 011 8401 | NTE85 | SK3122 | ||
| 2SC1740S-R | 405 011 8500 | NTE85 | SK3122 | |||
| 2SC1740S-S | 405 011 8609 | NTE85 | SK3122 | |||
| 2SC1815-O | 405 012 2101 | NTE85 | SK3124A | |||
| 2SC1815-Y | 405 012 2309 | NTE85 | SK3124A | |||
| 2SC945A-PA | 405 020 7501 | NTE85 | SK3124A | |||
| 2SC945A-QA | 405 020 7709 | NTE85 | SK3124A | |||
| 2SC945A-RA | 405 020 7907 | NTE85 | SK3124A | |||
| Q1001, 02, 03 | 2SC1815-GR | 405 012 2002 | NTE85 | SK3124A | ||
| 2SC1740S-Q | 405 011 8401 | NTE85 | SK3122 | |||
| 2SC1740S-R | 405 011 8500 | NTE85 | SK3122 | |||
| 2SC1740S-S | 405 011 8609 | NTE85 | SK3122 | |||
| 2SC1815-0 | 405 012 2101 | NTE85 | SK3124A | |||
| 2SC1815-Y | 405 012 2309 | NTE85 | SK3124A | |||
| 2SC945A-PA | 405 020 7501 | NTE85 | SK3124A | |||
| 2SC945A-QA | 405 020 7709 | NTE85 | SK3124A | |||
| 2SC945A-RA | 405 020 7907 | NTE85 | SK3124A | |||
| Q1021, 22 | 2SC1815-GR | 405 012 2002 | NTE85 | SK3124A | ||
| 2SC1740S-Q | 405 011 8401 | NTE85 | SK3122 | |||
| 2SC1740S-R | 405 011 8500 | NTE85 | SK3122 | |||
| 2SC1740S-S | 405 011 8609 | NTE85 | SK3122 | |||
| 2SC1815-Y | 405 012 2309 | NTE85 | SK3124A | |||
| 2SC945A-PA | 405 020 7501 | NTE85 | SK3124A | |||
| 2SC945A-OA | 405 020 7709 | NTE85 | SK31244 | |||
PARTS LIST continued
| Item No. | Function/Rating | Mfr. Part No. | NTE Part No | |
|---|---|---|---|---|
| # | PS601 | 8 Cold PTC | 408 006 7304 | - |
| # | R101 | 2.2 5% 1/4W | 401 015 6603 | QW2D2 |
| # | R104 | 180 5% 1/4W | 401 015 1608 | QW118 |
| # | R401, 02 | 3900 5% 2W | 401 068 0207 | 2W239 |
| # | R407 | 6800 5% 2W | 401 069 3702 | 2W268 |
| # | R413 | 4.7 10% 7W Wirewound | 402 076 0005 | - |
| # | R418 | 2700 5% 1/2W | 401 009 1607 | HW227 |
| # | R421 | 1.65K 1% 1/6W | 401 252 6505 | - |
| # | R422 | 10K 1% 1/6W | 401 052 6802 | - |
| # | R423 | 3300 1% 1/6W | 401 053 2605 | - |
| # | R469 | 27 5% 1W | 401 060 6405 | 1W027 |
| # | R481 | 47 5% 1/2W Nonflammable | 401 010 2600 | HW047 |
| # | R482 | 10 5% 1/4W Nonflammable | 401 011 9004 | QW010 |
| # | R483 | 1 5% 1/2W Nonflammable | 401 006 7701 | HW1D0 |
| # | R484 | 1.5 5% 1W | 401 057 9907 | 1W1D5 |
| # | R486 | 27 5% 2W | 401 066 9103 | 2W027 |
| # | R488 | 2.2 5% 1W | 401 059 9608 | 1W2D2 |
| # | R489 | 4.7 5% 2W | 401 068 1600 | 2W047 |
| R492 | 33K 1% 1/6W | 401 115 8504 | - | |
| # | R497 | 1 5% 2W | 401 064 3806 | 2W1D0 |
| # | R507 | .82 5% 1W | 401 057 7507 | 1WD82 |
| # | R511 | 330 5% 1W | 401 061 2505 | 1W133 |
| # | R601 | 1.8 10% 8W Wirewound | 402 071 3001 | - |
| 1.8 10% 7W Wirewound | 402 072 3109 | - | ||
| # | R606 | 47 5% 1/2W Nonflammable | 401 010 2600 | HW047 |
| # | R607 | 12 5% 2W | 401 065 1801 | 2W012 |
| # | R608 | 190 5% 10W Wirewound | 402 078 6302 | - |
| # | R609 | 220 5% 10W Wirewound | 402 074 7600 | 10W122 |
| # | R610 | 12 5% 2W | 401 065 1801 | 2W012 |
| # | R621 | 820 10% 6W Wirewound | 402 078 6203 | - |
| # | R622 | 270 5% 2W | 401 067 0000 | 2W127 |
| # | R624 | 330 5% 1W | 401 061 2505 | 1W133 |
| # | R625 | 5600 5% 1/6W | 401 027 2600 | - |
| # | R711, 12, 13 | 12K 5% 1W | 401 065 4604 | 1W312 |
| # | R1020 | 3.3M 10% 1/2W | 402 000 0705 | HW533 |
| R3406 | 16.5 1% 1/16W | 401 256 8008 | - | |
| VR1023 | 1000 Video Input | 645 006 5415 | - | |
| 1000 Video Input | 610 232 7861 | - | ||
| 1000 Video Input | 645 022 9503 | - |
| Item No. | Rating | Mfr. Part No. |
|---|---|---|
| # C411 | .012 3% 1.5kV | 404 066 4109 |
| # C412 | .0015 10% 3kV | 403 254 9506 |
| .0015 10% 3kV | 403 232 2604 | |
| # C416 | .2 5% 200V | 403 082 8019 |
| #_C417 | .33 5% 200V | 403 082 9818 |
| C493 | 2.2μF 20% 100V NP | 404 056 5307 |
| # C601 | .068 10% 250VAC | 404 072 7903 |
| .068 10% 275VAC | 404 073 7506 | |
| # C604, 05 | .001 10% 500V | 403 075 7111 |
| # C708 | .001 +80% -20% 2kV | 403 175 3419 |
| .001 +80% -20% 2kV | 403 077 2807 | |
| # C1020 | .0022 20% 125VAC | 404 008 6802 |
| C3406 | 4.7μF 20% 25V NP | 403 166 1605 |
| C3412 | 3.3µF 10% 10V Tantalum | 403 090 6004 |
| C3414 | 10µF 10% 10V Tantalum | 403 090 3607 |
| Item | Mfr. Part No. |
|---|---|
| Badge (SANYO) | 610 236 9274 |
| Button Unit | 610 257 8614 |
| Cabinet Front Assembly | 610 272 8095 |
| Cabinet Rear | 610 271 5676 |
| Remote Control Lens | 610 265 3786 |
| Demote T erre (200) |
PARTS LIST continued
| Item No. | Function/Rating | Mfr. Part No. |
|---|---|---|
| L164 | 15µH | 645 003 971 |
| 15µH | 645 016 265 | |
| L166 | 33µH | 645 003 981 |
| 33µH | 645 016 298 | |
| L203 | 5.6µH | 645 008 289 |
| 5.6µH | 645 016 310 | |
| L346 | 10µH | 610 031 387 |
| 10µH | 645 016 253 | |
| L401 | 3.3µН | 645 017 767 |
| L402 | Ferrite Bead | 610 031 999 |
| # L413 | Linearity | 645 025 441 |
| L801, 21, 51 | 5.6µН | 645 008 289 |
| 5.6µH | 645 016 310 | |
| # L901 | Degaussing | 645 030 190 |
| # L902 | Yoke Horiz 1.12mH | - |
| Vert 17.7mH | ||
| L1901 | 5.6µH | 645 008 289 |
| 5.6µН | 645 016 310 | |
| # LF601 | Line Filter | 610 031 593 |
| Line Filter | 610 223 12 | |
| Line Filter | 645 017 61 | |
| # T016 | Audio Output | 645 009 003 |
| # T036 | Audio Output | 645 009 003 |
| T131 | FM Detect | 645 027 60 |
| T151 | VCO, 45.75MHz | 645 027 60 |
| #_ T401 | Horizontal Driver | 610 000 113 |
| Horizontal Driver | 610 223 16 | |
| # T402 (1) | Horizontal Output | 645 018 95 |
| # T1001 | Pulse | 645 011 60 |
| Pulse | 645 011 80 | |
| Pulse | 610 229 90 |
| MISCELLANEOUS | ||||
|---|---|---|---|---|
| Item No. | Description | Mfr. Part No. | Notes | |
| # | A101 | Tuner | 645 027 5203 | UHF/VHF, 1AV4F1BAM019 |
| # | A101H | Block | 645 011 9682 | Antenna |
| A1901 | Receiver | 645 027 4213 | Remote | |
| # | F601 | Fuse | 423 018 8101 | 4Amp, 125V, Fast Acting |
| Fuse | 423 007 1601 | 4Amp, 125V, Fast Acting | ||
| Fuse | 423 007 1809 | 4Amp, 125V, Fast Acting | ||
| F601A | Fuse Holder | 645 000 5077 | For F601 (2 Used) | |
| Fuse Holder | 645 016 0479 | For F601 (2 Used) | ||
| F601B | Fuse Holder | 645 000 5077 | For F601 (2 Used) | |
| Fuse Holder | 645 016 0479 | For F601 (2 Used) | ||
| K1001 | Jack | 645 001 6097 | Assembly | |
| K701A | Socket | 645 025 6103 | CRT | |
| O901 | CRT | 414 009 7005 | A68ADT25X03 | |
| RL601 | Relay | 645 000 4155 | Power | |
| Relay | 645 011 2713 | Power | ||
| Relay | 645 024 7828 | Power | ||
| Relay | 645 015 8629 | Power | ||
| SP901.02 | Speaker | 610 055 6614 | 3" Round, 8 Ohms, 2W | |
| SW1901 | Switch | 645 004 3062 | Power | |
| SW1902 | Switch | 645 004 3062 | Volume Up | |
| SW1903 | Switch | 645 004 3062 | Volume Down | |
| SW1904 | Switch | 645 004 3062 | Channel Up | |
| SW1905 | Switch | 645 004 3062 | Channel Down | |
| SW1906 | Switch | 645 004 3062 | Menu | |
| W601 | Line Cord | 645 014 2444 | AC. Polarized | |
| Line Cord | 645 023 1698 | AC Polarized | ||
| X141 | Filter | 421 006 3206 | SAW | |
| X153 | Filter | 610 015 2946 | 4.5MHz | |
| X161 | Trap | 610 015 3059 | 4.5MHz | |
| X251 | Crystal | 610 204 4195 | 3.58MHz | |
| Crystal | 610 245 9746 | 3.58MHz | ||
| Crystal | 610 012 0655 | 3.58MHz | ||
| X401 | Crystal | 645 020 9147 | 507 5kHz | |
| X801 | Crystal | 645 000 6692 | 8MHz | |
| Crystal | 645 021 5483 | 8MHz | ||
| PC Board | 610 270 9407 | CRT | ||
| PC Board | 610 270 2407 | Main | ||
| Transmitter | 645 026 8182 | Remote | ||
| Transmitter | 645 026 8000 | Remote | ||
MODEL AVM-2758G (CHASSIS G5G-2758G)
SANYO
SET 4115 Page 4
Loading...