Sanyo SAP–K92A,SAP–K122A,SAP–K252A,SAP–C182A,SAP–C252A,SAP–C92A,SAP–C122A,SAP–K182A Technical & Service Manual

TECHNICAL & SERVICE MANUAL

SAP–K92A + SAP–C92A
SAP–K122A + SAP–C122A
SAP–K182A + SAP–C182A
SAP–K252A + SAP–C252A

FILE NO.

REFERENCE NO. SM700569

Indoor Unit

Outdoor Unit

SPLIT SYSTEM AIR CONDITIONER

SAP–K92A
SAP–K122A

SAP–C92A
SAP–C122A

Indoor Model No. Product Code No. Destination

SAP–K92A–S 1 852 083 68
SAP–K122A–S 1 852 083 69

Outdoor Model No. Product Code No. Destination

SAP–C92A–S 1 852 084 09
SAP–C122A–S 1 852 084 10
SAP–C182A–S 1 852 084 11

SAP–K182A–S 1 852 083 70

SAP–C182A
SAP–C252A

SAP–K182A
SAP–K252A

SAP–C252A–S 1 852 084 13SAP–K252A–S 1 852 083 72

Australia Australia

i

Important!
Please Read Before Starting

This air conditioning system meets strict safety and
operating standards. As the installer or service person,
it is an important part of your job to install or service the
system so it operates safely and efficiently.

For safe installation and trouble-free operation, you
must:

●Carefully read this instruction booklet before
beginning.

●Follow each installation or repair step exactly as
shown.

●Observe all local, state, and national electrical codes.

●Pay close attention to all warning and caution notices

given in this manual.

This symbol refers to a hazard or
unsafe practice which can result
in severe personal injury or
death.

This symbol refers to a hazard or
unsafe practice which can result
in personal injury or product or
property damage.

If Necessary, Get Help

These instructions are all you need for most installation
sites and maintenance conditions. If you require help
for a special problem, contact our sales/service outlet
or your certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for
improper installation or maintenance service, including
failure to follow the instructions in this document.

Special Precautions

When Wiring

ELECTRICAL SHOCK CAN CAUSE
SEVERE PERSONAL INJURY OR
DEATH. ONLY A QUALIFIED,
EXPERIENCED ELECTRICIAN SHOULD
ATTEMPT TO WIRE THIS SYSTEM.

• Do not supply power to the unit until all wiring and
tubing are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this
system. Carefully refer to the wiring diagram and
these instructions when wiring. Improper connections
and inadequate grounding can cause accidental
injury or death.

• Ground the unit following local electrical codes.

• Connect all wiring tightly. Loose wiring may cause
overheating at connection points and a possible fire
hazard.

WARNING

CAUTION

WARNING

When Transporting

Be careful when picking up and moving the indoor and
outdoor units. Get a partner to help, and bend your
knees when lifting to reduce strain on your back. Sharp
edges or thin aluminum fins on the air conditioner can
cut your fingers.

When Installing…

…In a Ceiling or Wall

Make sure the ceiling/wall is strong enough to hold the
units weight. It may be necessary to construct a strong
wood or metal frame to provide added support.

…In a Room

Properly insulate any tubing run inside a room to
prevent “sweating” that can cause dripping and water
damage to walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to
provide a solid, level foundation for the outdoor unit.
This prevents water damage and abnormal vibration.

…In an Area with High Winds

Securely anchor the outdoor unit down with bolts and a
metal frame. Provide a suitable air baffle.

…In a Snowy Area (for Heat Pump-type Systems)

Install the outdoor unit on a raised platform that is
higher than drifting snow. Provide snow vents.

When Connecting Refrigerant Tubing

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces
of the flare and union tubes before connecting them,
then tighten the nut with a torque wrench for a leak­free connection.

• Check carefully for leaks before starting the test run.

When Servicing

• Turn the power off at the main power box (mains)
before opening the unit to check or repair electrical
parts and wiring.

• Keep your fingers and clothing away from any
moving parts.

• Clean up the site after you finish, remembering to
check that no metal scraps or bits of wiring have
been left inside the unit being serviced.

Others

• Ventilate any enclosed areas when installing or
testing the refrigeration system. Escaped refrigerant
gas, on contact with fire or heat, can produce
dangerously toxic gas.

• Confirm upon completing installation that no
refrigerant gas is leaking. If escaped gas comes in
contact with a stove, gas water heater, electric room
heater or other heat source, it can produce
dangerously toxic gas.

CAUTION

Table of Contents

Page

1. OPERATING RANGE .............................................................................................................................. 1

2. SPECIFICATIONS

2-1. Unit Specifications.......................................................................................................................... 2

2-2. Major Component Specifications.................................................................................................... 6

2-3. Other Component Specifications.................................................................................................... 14

3. DIMENSIONAL DATA.............................................................................................................................. 16

4. REFRIGERANT FLOW DIAGRAM ......................................................................................................... 20

5. PERFORMANCE DATA

5-1. Performance charts ....................................................................................................................... 22

5-2. Air Throw Distance Chart .............................................................................................................. 24

5-3. Cooling Capacity ........................................................................................................................... 26

6. ELECTRICAL DATA

6-1. Electrical Characteristics................................................................................................................ 30

6-2. Electric Wiring Diagrams................................................................................................................ 32

7. INSTALLATION INSTRUCTIONS

7-1. Installation Site Selection ............................................................................................................... 36

7-2. Remote Control Unit Installation Position....................................................................................... 38

7-3. Recommended Wire Length and Diameter ................................................................................... 39

8. FUNCTION

8-1. Room Temperature Control ........................................................................................................... 40

8-2. Dry Operation ................................................................................................................................ 41

8-3. Freeze Prevention ......................................................................................................................... 41

8-4. Outdoor Fan Speed Control .......................................................................................................... 42

9. TROUBLESHOOTING

9-1. Check before and after troubleshooting ........................................................................................ 43

9-2. Air conditioner does not operate .................................................................................................... 44

9-3. Some part of air conditioner does not operate ..............................................................................48

9-4. Air conditioner operates, but abnormalities are observed ............................................................. 50

10. CHECKING ELECTRICAL COMPONENTS

10-1. Measurement of Insulation Resistance .......................................................................................... 51

10-2. Checking Continuity of Fuse on PCB Ass'y.................................................................................... 52

10-3. Checking Motor Capacitor ............................................................................................................. 52

11. MAINTENANCE

11-1. Changing Address of Remote Control Unit in Indoor Unit ............................................................. 53

.................................................................................................................................................. 54

APPENDIX

ii

1

1. OPERATING RANGE

Temperature Indoor Air Intake Temp. Outdoor Air Intake Temp.

Cooling

Maximum 32°C D.B. / 23°C W.B. 43°C D.B.

Minimum 19°C D.B. / 14°C W.B. 19°C D.B.

2

2. SPECIFICATIONS

2-1. Unit Specifications

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Power Source 220 – 240 V Single phase 50 Hz
Voltage rating V 220 / 230 / 240

Cooling

Capacity

kW 2.55 / 2.55 / 2.50

BTU/h 8,700 / 8,700 / 8,500
Air circulation (High) m3/h 430
Moisture removal (High) Liters/h 0.80
Available voltage range V 198 to 264
Running amperes A 3.9 / 3.8 / 3.9
Power input W 840 / 860 / 930
Power factor % 98 / 98 / 99
C.O.P. W/W 3.04 / 2.97 / 2.69
Compressor locked rotor amperes A 19 / 20 / 21
Controls / Temperature control Microprocessor / I.C. thermostat
Control unit Wireless remote control unit
Timer 1-hour OFF / 12-hour ON or OFF
Fan speeds Indoor / Outdoor 3 and Auto / 1 (Hi)

Airflow direction (Indoor)

Horizontal Manual

Vertical Auto
Air filter Washable, Anti-Mold
Compressor Rotary (Hermetic)
Refrigerant / Amount charged at shipment g R22 / 850
Refrigerant control Capillary tube

Operation sound

Indoor – Hi / Me / Lo dB-A 39 / 37 / 33

Outdoor – Hi dB-A 44
Refrigerant tubing connections Flare type
Max. allowable tubing length at shipment m 7.5

Refrigerant tube

Narrow tube mm (in.) 6.35 (1/4)
diameter

Wide tube mm (in.) 9.52 (3/8)
Refrigerant tube kit / Accessories Optional / Hanging wall bracket

Indoor Unit Outdoor Unit

Unit dimensions Height mm 250 530

Width mm 790 680

Depth mm 174 225
Package dimensions Height mm 242 580

Width mm 850 812

Depth mm 312 315

Weight Net

kg 7.0 29.0

Shipping

kg 10.0 31.0

Shipping volume m3 0.06 0.15

Dimensions & Weight Features Electrical Rating Performance

Indoor Unit SAP–K92A
Outdoor Unit SAP–C92A

3

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Power Source 220 – 240 V Single phase 50 Hz
Voltage rating V 220 / 230 / 240

Cooling

Capacity

kW 3.40 / 3.40 / 3.40

BTU/h 11,600 / 11,600 / 11,600
Air circulation (High) m3/h 470
Moisture removal (High) Liters/h 1.1
Available voltage range V 198 to 264
Running amperes A 5.8 / 5.8 / 5.9
Power input W 1,240 / 1,250 / 1,290
Power factor % 97 / 94 / 91
C.O.P. W/W 2.74 / 2.72 / 2.64
Compressor locked rotor amperes A 32 / 33 / 35
Controls / Temperature control Microprocessor / I.C. thermostat
Control unit Wireless remote control unit
Timer 1-hour OFF / 12-hour ON or OFF
Fan speeds Indoor / Outdoor 3 and Auto / Auto (Hi, Lo)

Airflow direction (Indoor )

Horizontal Manual

Vertical Auto
Air filter Washable, Anti-Mold
Compressor Rotary (Hermetic)
Refrigerant / Amount charged at shipment g R22 / 875
Refrigerant control Capillary tube

Operation sound

Indoor – Hi / Me / Lo dB-A 40 / 37 / 34

Outdoor – Hi dB-A 46
Refrigerant tubing connections Flare type
Max. allowable tubing length at shipment m 7.5

Refrigerant tube

Narrow tube mm (in.) 6.35 (1/4)
diameter

Wide tube mm (in.) 12.7 (1/2)
Refrigerant tube kit / Accessories Optional / Hanging wall bracket

Indoor Unit Outdoor Unit

Unit dimensions Height mm 250 530

Width mm 790 680

Depth mm 174 225
Package dimensions Height mm 242 580

Width mm 850 812

Depth mm 312 315

Weight Net

kg 7.0 32.0

Shipping

kg 10.0 34.0

Shipping volume m3 0.06 0.15

Dimensions & Weight Features Electrical Rating Performance

Indoor Unit SAP–K122A
Outdoor Unit SAP–C122A

4

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Power Source 220 – 240 V Single phase 50 Hz
Voltage rating V 220 / 230 / 240

Cooling

Capacity

kW 5.15 / 5.15 / 5.00

BTU/h 17,600 / 17,600 / 17,100
Air circulation (High) m3/h 760
Moisture removal (High) Liters/h 2.7
Available voltage range V 198 to 264
Running amperes A 9.5 / 9.5 / 10.1
Power input W 2,000 / 2,030 / 2,130
Power factor % 96 / 93 / 88
C.O.P. W/W 2.58 / 2.54 / 2.35
Compressor locked rotor amperes A 50 / 53 / 55
Controls / Temperature control Microprocessor / I.C. thermostat
Control unit Wireless remote control unit
Timer 1-hour OFF / 12-hour ON or OFF
Fan speeds Indoor / Outdoor 3 and Auto / Auto (Hi, Lo)

Airflow direction (Indoor )

Horizontal Manual

Vertical Auto
Air filter Washable, Anti-Mold
Compressor Rotary (Hermetic)
Refrigerant / Amount charged at shipment g R22 / 1,350
Refrigerant control Capillary tube

Operation sound

Indoor – Hi / Me / Lo dB-A 41 / 38 / 36

Outdoor – Hi dB-A 53
Refrigerant tubing connections Flare type
Max. allowable tubing length at shipment m 7.5

Refrigerant tube

Narrow tube mm (in.) 6.35 (1/4)
diameter

Wide tube mm (in.) 12.7 (1/2)
Refrigerant tube kit / Accessories Optional / Hanging wall bracket

Indoor Unit Outdoor Unit

Unit dimensions Height mm 285 630

Width mm 995 810

Depth mm 196 275
Package dimensions Height mm 276 704

Width mm 1,070 953

Depth mm 363 396

Weight Net

kg 12.0 49.0

Shipping

kg 15.0 53.5

Shipping volume m3 0.11 0.25

Dimensions & Weight Features Electrical Rating Performance

Indoor Unit SAP–K182A
Outdoor Unit SAP–C182A

5

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Power Source 220 – 240 V Single phase 50 Hz
Voltage rating V 220 / 230 / 240

Cooling

Capacity

kW 7.00 / 7.00 / 7.00

BTU/h 23,900 / 23,900 / 23,900
Air circulation (High) m3/h 840
Moisture removal (High) Liters/h 3.3
Available voltage range V 198 to 264
Running amperes A 13.1 / 13.1 / 13.4
Power input W 2,730 / 2,730 / 2,800
Power factor % 95 / 91 / 87
C.O.P. W/W 2.56 / 2.56 / 2.50
Compressor locked rotor amperes A 67 / 70 / 73
Controls / Temperature control Microprocessor / I.C. thermostat
Control unit Wireless remote control unit
Timer 1-hour OFF / 12-hour ON or OFF
Fan speeds Indoor / Outdoor 3 and Auto / Auto (Hi, Lo)

Airflow direction (Indoor )

Horizontal Manual

Vertical Auto
Air filter Washable, Anti-Mold
Compressor Rotary (Hermetic)
Refrigerant / Amount charged at shipment g R22 / 1,700
Refrigerant control Capillary tube

Operation sound

Indoor – Hi / Me / Lo dB-A 43 / 41 / 39

Outdoor – Hi dB-A 55
Refrigerant tubing connections Flare type
Max. allowable tubing length at shipment m 10

Refrigerant tube

Narrow tube mm (in.) 6.35 (1/4)
diameter

Wide tube mm (in.) 15.88 (5/8)
Refrigerant tube kit / Accessories Optional / Hanging wall bracket

Indoor Unit Outdoor Unit

Unit dimensions Height mm 285 630

Width mm 995 810

Depth mm 196 275
Package dimensions Height mm 276 704

Width mm 1,070 953

Depth mm 363 396

Weight Net

kg 12.0 59.0

Shipping

kg 15.0 62.0

Shipping volume m3 0.11 0.25

Dimensions & Weight Features Electrical Rating Performance

Indoor Unit SAP–K252A
Outdoor Unit SAP–C252A

6

2-2. Major Component Specifications

2-2-1. Indoor Unit

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Part No. CB-K92GJ
Controls Microprocessor
Control circuit fuse 250 V – 3.15 A

Remote Control Unit RCS-3S4E-G

Type Cross–flow
Number ... Dia. and length mm 1 ... ø97 / L578
Fan motor model ... Number IBH-884-020 ... 1
No. of poles ... rpm (240 V, High) 2 ... 1,290
Nominal output W 20
Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 201

WHT – VLT : 261

Safety Type Thermal fuse
devices Operating temp. Open °C 130

Close —

Run capacitor µF 1.5

VAC 440
Type Stepping motor
Model MP24GA3
Rating DC 12 V
Coil resistance (Ambient temp. 25°C) Ω A pair of each terminal: 380 ± 7%
Coil Aluminum plate fin / Copper tube
Rows 2
Fin pitch mm 1.4
Face area m

2

0.110

Heat

Exch. Coil

Flap Motor

Fan & Fan Motor

Controller

PCB

Indoor Unit SAP–K92A

7

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Part No. CB-K122GJ
Controls Microprocessor
Control circuit fuse 250 V – 3.15 A

Remote Control Unit RCS-3S4E-G

Type Cross–flow
Number ... Dia. and length mm 1 ... ø97 / L578
Fan motor model ... Number IBH-884-020 ... 1
No. of poles ... rpm (240 V, High) 2 ... 1,350
Nominal output W 20
Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 201

WHT – VLT : 261

Safety Type Thermal fuse
devices Operating temp. Open °C 130

Close —

Run capacitor µF 1.5

VAC 440
Type Stepping motor
Model MP24GA3
Rating DC 12 V
Coil resistance (Ambient temp. 25°C) Ω A pair of each terminal: 380 ± 7%
Coil Aluminum plate fin / Copper tube
Rows 2
Fin pitch mm 1.4
Face area m

2

0.110

Heat

Exch. Coil

Flap Motor

Fan & Fan Motor

Controller

PCB

Indoor Unit SAP–K122A

8

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Part No. CB-K182GJ
Controls Microprocessor
Control circuit fuse 250 V – 3.15 A

Remote Control Unit RCS-3S4E-G

Type Cross–flow
Number ... Dia. and length mm 1 ... ø88 / L746
Fan motor model ... Number UF2-31A5P-S ... 1
No. of poles ... rpm (240 V, High) 2 ... 1,440
Nominal output W 30
Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 133.7

WHT – PNK : 168.4

Safety Type Internal protector
devices Operating temp. Open °C 130 ± 8

Close Automatic reclosing

Run capacitor µF 2.0

VAC 440
Type Stepping motor
Model MP24GA2
Rating DC 12 V
Coil resistance (Ambient temp. 25°C) Ω Each terminals (1–2, 1–3, 1–4, 1–5) : 400 ± 7%
Coil Aluminum plate fin / Copper tube
Rows 2
Fin pitch mm 1.3
Face area m

2

0.156

Heat

Exch. Coil

Flap Motor

Fan & Fan Motor

Controller

PCB

Indoor Unit SAP–K182A

9

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Part No. CB-K252G
Controls Microprocessor
Control circuit fuse 250 V – 3.15 A

Remote Control Unit RCS-3S4E-G

Type Cross–flow
Number ... Dia. and length mm 1 ... ø88 / L746
Fan motor model ... Number UF2-31A5P-S ... 1
No. of poles ... rpm (240 V, High) 2 ... 1,440
Nominal output W 30
Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 133.7

WHT – PNK : 168.4

Safety Type Internal protector
devices Operating temp. Open °C 130 ± 8

Close Automatic reclosing

Run capacitor µF 2.0

VAC 440
Type Stepping motor
Model MP24GA2
Rating DC 12 V
Coil resistance (Ambient temp. 25°C) Ω Each terminals (1–2, 1–3, 1–4, 1–5) : 400 ± 7%
Coil Aluminum plate fin / Copper tube
Rows 2
Fin pitch mm 1.3
Face area m

2

0.156

Heat

Exch. Coil

Flap Motor

Fan & Fan Motor

Controller

PCB

Indoor Unit SAP–K252A

10

2-2-2. Outdoor Unit

Type Rotary (Hermetic)
Compressor model C–R81H5Q 80682645–S
Nominal output W 800
Compressor oil ... Amount cc 4GSD–T or SAY-56T ... 500
Coil resistance (Ambient temp. 25°C) Ω C – R : 3.38

C – S : 7.49

Type External (OLR A) External (OLR T)
Safety Overload relay MRA99109–9201 CS–7C115
devices Operating temp. Open °C 150 ± 5 115 ± 3

Close °C 69 ± 11 95 ± 5

Operating amp.(Ambient temp. 25°C) Trip in 6 to 16 sec. at 16 A —
Run capacitor µF 22.5

VAC 400
Type Propeller
Number ... Dia. mm 1 ... ø 370
Fan motor model ... Number UE6-21AH5PB-S ... 1
No. of poles ... rpm (240 V, High) 6 ... 780
Nominal output W 20

Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 338.3

WHT – PNK : 389.7

Safety Type Thermal fuse
devices Operating temp. Open °C 145 ± 2

Close —

Run capacitor µF 1.5

VAC 440
Coil Aluminum plate fin / Copper tube
Rows 1
Fin pitch mm 1.3
Face area m

2

0.333

External Finish Acrylic baked-on enamel finish

Heat

Exch. Coil

Compressor

Fan & Fan Motor

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Outdoor Unit SAP–C92A

11

Type Rotary (Hermetic)
Compressor model C–R112H5X 80616745–S
Nominal output W 1,100
Compressor oil ... Amount cc 4GSD–T or SAY-56T ... 550
Coil resistance (Ambient temp. 25°C) Ω C – R : 1.96

C – S : 5.38

Type External (OLR A)

Safety

Overload relay MRA99122–9201

devices Operating temp. Open °C 150 ± 5

Close °C 69 ± 11

Operating amp.(Ambient temp. 25°C) Trip in 6 to 16 sec. at 25 A

Run capacitor µF 25.0

VAC 400
Type Propeller
Number ... Dia. mm 1 ... ø 370
Fan motor model ... Number UE6S–21AC5P–S ... 1
No. of poles ... rpm (240 V, High) 6 ... 780
Nominal output W 20

Coil resistance (Ambient temp. 20°C) Ω BRN – WHT : 341.2

WHT – YEL : 212.7

YEL – PNK : 190.0

Safety

Type Thermal fuse

devices Operating temp. Open °C 145 ± 2

Close —

Run capacitor µF 1.5

VAC 440
Coil Aluminum plate fin / Copper tube
Rows 2
Fin pitch mm 1.2
Face area m

2

0.329

External Finish Acrylic baked-on enamel finish

Heat

Exch. Coil

Compressor

Fan & Fan Motor

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Outdoor Unit SAP–C122A

12

Type Rotary (Hermetic)
Compressor model 2JS350D5BC02 8520452625100
Nominal output W 1,700
Compressor oil ... Amount cc 4GSD–T or SAY-56T ... 1,130
Coil resistance (Ambient temp. 25°C) Ω C – R : 0.981

C – S : 2.845

Type Internal protector

Safety

Overload relay —

devices Operating temp. Open °C Automatic opening

Close °C Automatic reclosing

Operating amp.(Ambient temp. 25°C) —

Run capacitor µF 45.0

VAC 400
Type Propeller
Number ... Dia. mm 1 ... ø 420
Fan motor model ... Number KFG6S–51A5P–S ... 1
No. of poles ... rpm (240 V, High) 6 ... 880
Nominal output W 50

Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 67.09

WHT – YEL : 68.12

YEL – PNK : 15.66

Safety

Type Thermal protector

devices Operating temp. Open °C 130 ± 8

Close Automatic reclosing

Run capacitor µF 4.0

VAC 440
Coil Aluminum plate fin / Copper tube
Rows 1
Fin pitch mm 1.3
Face area m

2

0.506

External Finish Acrylic baked-on enamel finish

Heat

Exch. Coil

Compressor

Fan & Fan Motor

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Outdoor Unit SAP–C182A

13

Type Rotary (Hermetic)
Compressor model C-R221H5S 80687145
Nominal output W 2,200
Compressor oil ... Amount cc 4GSD–T or SAY-56T ... 1,350
Coil resistance (Ambient temp. 25°C) Ω C – R : 0.777

C – S : 2.408

Type Internal protector External (OLR T)

Safety

Overload relay — OL–D24

devices Operating temp. Open °C Automatic opening 150 ± 5

Close °C Automatic reclosing 63 ± 11

Operating amp.(Ambient temp. 25°C) — Trip in 6 to 16 sec. at 59 A

Run capacitor µF 40.0

VAC 400
Type Propeller
Number ... Dia. mm 1 ... ø 420
Fan motor model ... Number KFG4S–51C5PA–S ... 1
No. of poles ... rpm (240 V, High) 4 ... 1,000
Nominal output W 50

Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 55.1

WHT – YEL : 37.2

YEL – PNK : 15.5

Safety

Type Thermal protector

devices Operating temp. Open °C 130 ± 8

Close Automatic reclosing

Run capacitor µF 5.0

VAC 440
Coil Aluminum plate fin / Copper tube
Rows 2
Fin pitch mm 1.2
Face area m

2

0.499

External Finish Acrylic baked-on enamel finish

Heat

Exch. Coil

Compressor

Fan & Fan Motor

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Outdoor Unit SAP–C252A

2-3. Other Component Specifications

14

<Except SAP-C92>

Thermostat (Fan Speed Control 23S) MQT5S

Switching temp. °C

high ➞ LOW 28.5°C ± 1.5
low ➞ HIGH 31.5°C ± 2

Contact rating AC 220V, 3A

Power Relay (PR) EL1U

Coil rating AC 200–240V, 50/60Hz
Contact rating AC 277V, 30A

Outdoor Unit SAP–C92A

SAP–C122A

Thermistor (Room sensor) DTN-TKS128B

Resistance kΩ 25°C 5.0 ± 3%

Thermistor (Coil sensor) DTN-TKS131B

Resistance kΩ 0°C 15.0 ± 2%

Transformer (TR) ATR-J105

Rating Primary AC 230V, 50/60Hz

Secondary 19V, 0.526A
Capacity 10VA

Coil resistance Ω (at 21°C) Primary (WHT – WHT): 205 ± 10%

Secondary (BRN – BRN): 2.0 ± 10%

Thermal cut-off temp. 150°C

Indoor Unit SAP–K92A

SAP–K122A

15

Thermostat (Fan Speed Control 23S) MQT5S

Switching temp. °C

high ➞ LOW 28.5°C ± 1.5
low ➞ HIGH 31.5°C ± 2

Contact rating AC 220V, 3A

Power Relay (PR) EL1U

Coil rating AC 200–240V, 50/60Hz
Contact rating AC 277V, 30A

Outdoor Unit SAP–C182A

SAP–C252A

Thermistor (Room sensor) DTN-TKS142B

Resistance kΩ 25°C 5.0 ± 3%

Thermistor (Coil sensor) DTN-TKS131B

Resistance kΩ 0°C 15.0 ± 2%

Transformer (TR) ATR-J105

Rating Primary AC 230V, 50/60Hz

Secondary 19V, 0.526A
Capacity 10VA

Coil resistance Ω (at 21°C) Primary (WHT – WHT): 205 ± 10%

Secondary (BRN – BRN): 2.0 ± 10%

Thermal cut-off temp. 150°C

Indoor Unit SAP–K182A

SAP–K252A