Sanyo SO-WIN-KF3AC, QXXAVC922-P User Manual

Owner’s Manual

Network Set-up and Operation For Windows

Wired and Wireless Setting

Projector Set-up and Operation

Network Capture

Network Viewer

Moderator Function

This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed strictly.

Compliance

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. – Consult the dealer or an experienced radio/TV technician for help. Model Number : QXXAVC922---P Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 Telephone No. : (818)998-7322 This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) the device may not cause interference, and (2) the device must accept any interference, including interference that may cause undesired operation of this device.

CAUTION: Properly shielded a grounded cables and connectors must be used for connection to host

computer and /or peripherals in order to meet FCC emission limits.

VGA cable with ferrite core must be used for RF interference suppression.

For Canadian Users

This Class B digital apparatus complies with Canadian ICES-003. Cet apparei numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Exposure Warning

- This transmitter must be co-located or operated in conjunction with any other antenna or transmitter.

- This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and

meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment must be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).

The CE Mark is a Directive conformity mark of the European Community (EC).

The Alert Mark is a Directive conformity mark of the European Community.

English

Česky

[Czech]

Dansk

[Danish]

Deutsch

[German]

Eesti

[Estonian]

Español

[Spanish]

Ελληνική

[Greek]

Français [French]

Italiano [Italian] Latviski

[Latvian]

Lietuvių

[Lithuanian]

Nederlands

[Dutch]

Malti

[Maltese]

Magyar

[Hungarian]

Polski

[Polish]

Português

[Portuguese]

Slovensko

[Slovenian]

Slovensk y

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

Islenska

[Icelandic]

Norsk

[Norwe gian]

Hereby, SANYO Ele ctric Co., Ltd., declares that this WLAN Module (QX XAVC922---P) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

SANYO Electric Co., Ltd. tímto p rohlašuje, že tento WLAN Module (QXXAVC922-- -P) je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Un der teg nede SANYO Ele ctr ic Co. , Ltd. erk lær er her ved, at føl gende ud sty r W LAN Mo dul e (QXXAVC922-- -P) overholder de væsentlige k rav og øvrige relevante krav i direktiv 1999/5/EF.

Hie rmit erkl ärt SANYO Electri c Co. , Ltd ., d ass s ich das Gerät WLAN Modu le (Q XXAVC92 2--- P) in Üb ereinst immu ng mit den grund legen den Anf ord erung en und den üb rigen ei nsch lägig en Bestimmungen der R ichtlinie 1999/5/EG befindet.

Käes olevaga kinnitab SANYO Elec tric Co., Ltd. seadme WLAN Module (QXXAVC922- --P) vastavus t dir ekti ivi 1999/ 5/EÜ põhin õuete le j a nim etatud direktiiv ist tulen evate le teis tele asjakoh astel e sätetele.

Por medio de la presente SANYO Electric Co., Ltd. declara que el WLAN Module (QXXAVC922-- -P) cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ΜΕ ΤΗ Ν ΠΑ ΡΟΥ ΣΑ SAN YO Ele ctri c C o., Lt d. ΔΗΛΩ ΝΕΙ ΟΤ Ι WL AN Mo dul e ( QXX AVC9 22- -- P) ΣΥΜ ΜΟΡΦΩ ΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ ΔΕΙΣ ΑΠΑΙΤ ΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕ Σ ΣΧΕΤ ΙΚΕΣ ΔΙΑΤΑΞΕ ΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Par la présente SANYO El ectric Co., Ltd. déclare que l’appareil WLAN Module (QXXAVC922---P) est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Con la pre sente SANYO Elec tric Co., Ltd. dichiara che quest o WL AN Mo dule (QXXAVC922- --P) è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiv a 1999/5/CE.

Ar šo SANYO Electric Co., Ltd ., deklarē, ka WLAN Module (QXXAVC922---P) atbilst Direktīvas 1999/5/ EK būtiskajām prasībām un citiem ar to saistīt ajiem noteikumiem.

Šiuo SANYO Electric Co., Ltd.de klaruoja, k ad šis WLAN Module (QXXAVC922- --P) atitinka esminius reikalav imus ir kitas 1999/5/EB Direk tyvos nuostatas.

Hi erbij ver kla art SAN YO E lec tri c Co ., Ltd. da t het toe ste l WLA N M odul e ( QXX AVC922- --P ) in overeens temming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/ EG.

Hawnhekk, SANYO Electric Co., Ltd., jiddikjar a li dan WLAN Module (QXXAVC922- --P) j ikkonforma mal-ħtiġijiet ess enzjali u ma provvedimenti oħrajn relevanti li hemm f id-Dirrettiva 1999/5/EC.

Alulírott, SANYO Electric Co., Ltd . nyilatkozom, hogy a WLAN Module (QXXAVC922---P) megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC iránye lv egyéb elõírásainak.

Nini ejszym SANYO Electric Co., Ltd. oświadcza, że WLAN Modu le (QX XAVC922-- -P) jest zgodny z zasadniczymi wymogami oraz p ozostałymi stosownymi postanowieniami Dyrekt ywy 1999/5/EC.

SAN YO E lec tric Co. , Ltd. decl ara que este (QX XAVC922- -- P) e stá conform e co m os requ isit os essenciais e outras disposições da Direc tiva 1999/5/CE.

SANYO Elec tric Co., Ltd. izjavlja, da je ta (QXXAVC922-- -P) v skladu z bistvenimi zahtevami in ost alimi relevantnimi določili direktive 1999/5/ES.

SANYO Electric Co., Ltd. t ýmto vyhlasuje, že (QXXAVC922-- -P) spĺň a zákl adné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

SANYO Elec tric Co., Ltd. vakuuttaa täten et tä (QXXAVC922--- P) tyyppinen laite on direktiivin 1999/5/ EY oleellisten vaatimusten ja sitä koskevien direk tiivin muiden ehtojen mukainen.

Härmed intygar SANYO Electric Co., Ltd. att denna (QXXAVC922---P) står I överensstämmelse med de väsentliga egensk apskrav och övriga relevanta bestämm elser som framgår av direktiv 1999/5/EG.

Hér með lýsir SANYO Electric Co., Ltd. yfir því að (QXXAVC922---P) er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

SA NYO Ele ctr ic Co. , Ltd . e rkl ære r h erv ed at uts tyr et (QX XAVC 922- -- P) er i sam sva r m ed de grunnleggende k rav og øvrige relevante krav i direktiv 1999/5/EF.

Safety instructions

CAUTION IN USING THE PROJECTOR VIA NETWORKS

● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents.

● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents.

CAUTION IN USING NETWORK FUNCTION

● SANYO Electric Co., Ltd. assumes no responsibility for the loss or damage of data, or damage of the computer caused by using this projector. Making back-up copies of valuable data in your computer is recommended.

Caution about Radio Wave

This unit operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical equipment (such as pacemaker), as well as amateur radio stations.

Please read “Safety Instructions” section and make sure the following cautions.

1. Be sure that there are no other devices in the area that may use the same frequency band as Projector.

2. If any other devices are causing radio interferences, change the communication frequency channel or move to other location.

Trademarks and Copyright

Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Netscape Navigator and Netscape Communicator are registered trademarks or trademarks of Netscape Communications Corporation in the United States and other countries. Pentium is a registered trademark of Intel Corp. in the United States. Each name of corporation or product in this Owner’s Manual is either a registered trademark or a trademark of its respective corporation.

Notes

- The contents of this manual are subject to change without notice.

- You may not copy the printed materials accompanying with the software.

- We shall not be responsible for any damages caused by reliance on this manual.

Expression/Abbreviation

The OS of the computer and the Web browser described in this manual is Windows XP Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruction procedures may differ from the actual operation depending on your computer environment.

Use of this manual

This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective booklet.

Compliance .........................................................................................................................................................2

Safety instructions ............................................................................................................................................4

Table of contents ...............................................................................................................................................5

Operating environment and configuration .............................................................................................7

Required operating environment for computers .............................................................................. 7

Network specifications of the projector ................................................................................................8

1. About LAN functions ....................................................9

LAN functions and the features ................................................................................................................10

Image projecting system via LAN ............................................................................................................10

An example of the connection .................................................................................................................11

LAN connection modes ...............................................................................................................................12

2. Setup procedures .........................................................15

Installing the software .................................................................................................................................17

3. Names and functions of the operation screen ...........21

Network connection standby display ....................................................................................................22

Network Capture 5 window .......................................................................................................................23

4. Wired LAN configurations ...........................................25

Connecting to the LAN line........................................................................................................................26

Network environment settings.................................................................................................................26

Confirming the operation ...........................................................................................................................28

Network PIN code ..........................................................................................................................................30

Network information ....................................................................................................................................30

Wired factory default....................................................................................................................................30

Wired LAN factory default settings .........................................................................................................31

5. Wireless LAN configurations .......................................33

Setting the network environment ...........................................................................................................34

Setting procedures........................................................................................................................................34

Configuring security with the projector ................................................................................................36

Easy wireless setting .....................................................................................................................................39

Network PIN code ..........................................................................................................................................40

Network information ....................................................................................................................................40

Wireless factory default ...............................................................................................................................40

WIRELESS indicator display ........................................................................................................................41

Wireless LAN factory default settings ....................................................................................................42

6. Basic setting and operation .........................................43

Starting up the Browser ..............................................................................................................................44

How to use the setting page .....................................................................................................................46

Initial setting ....................................................................................................................................................48

Network configuration ................................................................................................................................51

Configuring wireless LAN setting and security setting....................................................................53

E-mail setting ..................................................................................................................................................55

SNMP setting ...................................................................................................................................................59

7. Controlling the projector ............................................63

Power control and status check ............................................................................................................... 64

Controls .............................................................................................................................................................66

PC adjustment ................................................................................................................................................70

Setting up the projector ..............................................................................................................................71

Timer setting ...................................................................................................................................................74

Projector information ...................................................................................................................................77

Multi-control ...................................................................................................................................................79

8. Network capture functions .........................................85

About Network Capture function ............................................................................................................86

Using the Real Time Capture .....................................................................................................................89

Using the Network Communication .......................................................................................................94

How to use the Network communication ...........................................................................................98

Network Communication operation and change of state ..............................................................101

Executing the forcing mode ......................................................................................................................102

Moderator function ......................................................................................................................................103

Preparation for using the moderator function ...................................................................................104

Using the moderator function ..................................................................................................................105

Moderator's password setting up ............................................................................................................106

Unregister moderator status .....................................................................................................................106

Error information ...........................................................................................................................................107

9. Network Viewer functions ...........................................109

Creating the available data [Network Viewer 5] .................................................................................110

Creating a program file [Program Editor] ..............................................................................................115

Using the Network Viewer function ........................................................................................................120

10. Appendix .....................................................................127

Use of telnet ....................................................................................................................................................128

Web browser setting .................................................................................................................................... 130

Firewall setting ...............................................................................................................................................135

Troubleshooting.............................................................................................................................................136

Terminology.....................................................................................................................................................142

Operating environment and configuration

Required operating environment for computers

When operating the projector via the networks, computers should meet the operating environment below.

Microsoft Windows 2000 or

CPU

Microsoft Windows XP or Microsoft Windows Vista (32bit version)

Pentium 3 ; 1GHz or higher (more than 2GHz is recommended) for Windows 2000 or Windows XP Pentium 4 ; 3GHz or higher for Windows Vista

Memory

Free HDD Space 100MB

Screen Resolution

Communication Protocol TCP/IP

Network

Correspond

Browser Application

Wireless LAN Correspond to IEEE802.11b/g

Wired LAN

256MB or more for Windows 2000 or Windows XP 1GB or more for Windows Vista

Required to support any of VGA (640 x 480), SVGA (800 x 600), XGA (1024 x 768), The color number should be either 16 bit (65536 colors) or 24/32 bit (16.77 million colors).

Correspond to 100BASE-TX (100Mbpd) /10BASE-T (10Mbps)

Microsoft Internet Explorer Ver.4.0 or later Netscape Communications Netscape Communicator Ver.6.0 or later

Network specifications of the projector

LAN Terminal

Data communication speed 100Base-TX (100Mbps)/10Base-T (10Mbps)

Protocol TCP/IP

Wireless LAN

Interface IEEE802.11b/g

Compliance

Communication Mode

Data Transfer Speed

Wireless Frequency (Channel) 2412MHz–2462MHz (CH1–CH11)

Modulation Form

Protocol TCP/IP

Security

Service area

Countries and Standards

AdHoc, Infrastructure

1/2/5.5/11Mbps (IEEE802.11b) 6/9/12/18/24/36/48/54Mbps (IEEE802.11g)

IEEE802.11g OFDM 54/4Mbps 64QAM, 36/24Mbps 16QAM, 18/12Mbps QRSK, 9/6Mbps BPSK IEEE802.11b DSSS 11/5Mbps CCK, 2Mbps DQPSK, 1Mbps DBPSK

WEP 64Bit (Open/Shared) /WEP 128Bit (Open/Shared), WPA-PSK(TKIP), WPA2-PSK(AES), SSID, ESSID

about 30 m (without disturbance) Differs according to the operating environment.

JAPAN: VCCI ClassB,TELEC (Wireless)

USA: FCC Part15 Subpart C (Wireless) FCC Part15 Subpart C, Class B

Canada: IC RSS-210 (Wireless), IC ICES-003 ClassB

Europe: R&TTE, EMC, LVD

1. About LAN functions

This chapter describes the features, the mechanism, and connection procedures of the LAN.

Chapter

Chapter 1 About L AN functions

LAN functions and the features

This product is loaded with a LAN network function which enables you to project an image on the computer through a projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector under various network environments to meet the wide-ranging needs of the operation.

• Accept both Wired and Wireless LAN environment. When the projector is operated via Wireless LAN,

there is no need for wire connection.

• Remove the burden of LAN settings. Easy LAN setting function is provided.

• One computer image can be projected up to 5 projectors simultaneously.

• Network capture function to project the computer's screen image through the projector.

• Remote function which allows you to operate the projector from a distance.

• Monitoring function for the projector operation.

• E-mail function which reports the operating status to your maintenance management.

• Network viewer function which remotely operates the image data on the server to project through

the projector.

• Moderator function with which the moderator can project the image on the participants’ computer

screen at the meetings or the classes.

• Multi control function which can operate multiple projectors (up to 100) simultaneously.

Image projecting system via LAN

The images are projected through an image capturing system which helps to project the faithful computer images. With this system, you can use the product under various application environments despite the differences of application software.

Flow of Image Transfer

1. Download the computer image with the dedicated software faithfully to the real image.

2. The downloaded data will be compressed to the digital signal and transferred to the projector via the

LAN (Wired or Wireless). (One computer can operate up to 5 projectors simultaneously.)

3. Digital signal will be reproduced into RGB image signal and will be projected by the projector.

✳ The image will be transferred to each projector. The time lag can occur between each projection.

CAUTION: This product does not correspond to the application with DirectX, MSOffice assistant, and video replay such as DVD.

0.0

0.5

1.0

1.5

2.0

0.0

0.5

1.0

1.5

2.0

0.0

0.5

1.0

1.5

2.0

An example of the connection

The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector .

Access pointComputer (1)

Computer (2)

Chapter 1 About L AN functions

LAN connection modes

Connection modes differ depending on the LAN and computer environments. Connect appropriately for each environment.

■ Wireless LAN, Infrastructure Communication Mode

Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or, communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment will select an access point to communicate SSID/ESSID modes. These communication modes are used when both Wireless LAN and Wired LAN are used in the same network environment.

Computer (2)

■ Wireless LAN, AdHoc Communication Mode

Communication mode between Wireless LAN equipment. (Communication mode via SSID/ESSID)

Wireless communication mode corresponded computer: AdHoc

Access pointComputer (1)

Network Projector

Wireless communication mode :AdHoc

Wireless communication mode corresponded computer: Infrastructure

LAN connection modes

■ Wired LAN Communication Mode

Communicate via the LAN line.

Computer(1) Computer(2) Computer (3)

✳ Operate the computer mouse with the remote control. When the projector’s remote control employs mouse operating function, you can operate

the computer by the remote control which is provided with the projector. To use the remote control, point to the projector. You do not need to connect the USB cable to operate the computer mouse.

(For details about the remote control operation, refer to the owner’s manual of the projector.)

Chapter 1 About L AN functions

2. Setup procedures

This chapter describes how to install the Network Capture 5 software and how to set up the networks.

Chapter

Chapter 2 Setup procedures

To use the projector via the networks, follow the setup procedures below.

STEP 1

STEP 2

STEP 3

Install the software on computers.

Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install.

Select Wired LAN or Wireless LAN then connect the

LAN and set the configuration.

Decide depending on the LAN environment.

Wired LAN ............ Refer to “4. Wired LAN Configurations” (pp.25–31).

Wireless LAN ....... Refer to “5. Wireless LAN Configurations” (pp.33–42).

Detailed LAN configurations need to be done with a browser later. First, complete the Wired or Wireless LAN connection between computers and projectors, then start browser configurations. ➔ “6. Basic setting and operation” (pp.43–62).

Network Configuration has completed.

Follow each chapter to project an image and operate the projector.

■ Operate and manage the projector ➔ “7. Controlling the projector” (pp.63-84) ➔ “Projector Power status and check” (p.64) ➔ “Controls” (p.66) ➔ “PC adjustment” (p.70) ➔ “Setting up the projector” (p.71) ➔ “Timer setting” (p.74) ➔ “Projector information” (p.77) ➔ “Multi-control” (p.79)

■ Project an image on the computer ➔ “8. Network capture functions" (pp.85-108) ➔ “Use of real time capture” (p.89) ➔ “Use of network communication” (p.94) ➔ “Moderator function” (p.103)

■ Project an image on a network server ➔ “9. Network Viewer functions” (pp.109-126) ➔ “Create the available data” (p.110). ➔ “Create the program files” (p.115). ➔ “Project the image with network viewer function” (p.120)

Installing the software

It is required to install the software into your computer to use the Network Capture function . Please install the software as follows.

Note: To install the software into the computer with Windows 2000, Windows XP or Windows

Vista, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise proper installation cannot be made.

Network Viewer & Capture 5 installation

1 Set the supplied Network Viewer & Capture 5 CD-ROM into the CD-ROM drive of your computer.

Double click SetupTool.exe icon in the "Tool" folder in the CD-ROM.

2 Select "English [United States]" from the pull-down menu on the "Choose Setup Language" window

and click OK button to start installing and then follow the installation wizards.

Chapter 2 Setup procedures

As the "License Agreement" will appear, read contents carefully and click Yes button if you agree to the license agreement to proceed with installing.

During the installation, following window may appear, click Continue Anyway button.

3 Click Finish to complete the installation.

Installing the software

Installed software

The following 3 softwares are installed on your computer.

● Network Capture 5:

Captures the displayed image and the sound of the computer and serves them to the projector via the network.

● Network Viewer 5 (File Converter 1):

Converts to the JPEG*1 data format which can be projected with the projector from the JPEG, bitmap and Power Point files.

● Network Viewer 5 (Program Editor) :

This is a tool to make the program which has a function to specify and order the projecting JPEG image data stored in the file servers.

* To uninstall these software, use "Add/Remove Program" from the control panel. *1 This product supports the JPEG image format. This file is needed to convert to the optimized JPEG file by using the

File Converter 1 software previously. Refer to the item "Creating the available data [Network Viewer 5]"(+p.110) about data converting for the projection.

Chapter 2 Setup procedures

File Converter 2 installation

1 Set the supplied Network Viewer & Capture 5 CD-

ROM into the CD-ROM drive of your computer. Double click SetupDrv.exe icon in the "Driver" folder in the CD-ROM.

2 Select "English [United States]" from the pull-down

menu on the language selection window and then click Install button to start installing.

Installed software and places

Network Viewer 5 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control Panel".

● Network Viewer 5 (File Converter 2):

This is a kind of the printer driver to convert to the JPEG data optimized to project by the projector from any of the documents created by the application software.

* To uninstall Network Viewer 5 (File Converter 2), just delete the "Network Viewer 5(File Converter 2)" icon from the

"Printers and faxes" folder.

3. Names and functions of the operation screen

This chapter describes the functions of each part of the operation screen.

Chapter

Chapter 3 Names and functions of the operating screen

Network connection standby display

Turn on the projector and select either “Wired” or “Wireless” from the input menu of the projector. The “Please wait...” message will be displayed on the screen. After short time, the network connection standby display screen will appear as below. While the “Please wait...” message is shown, you cannot operate the projector.

Network Connection Standby Display

Network Capture 5 window

This software is to project the computer screen via the networks.

Select "All Programs" from the start menu --> Network Viewer & Capture 5" --> "Network Capture 5", then following screen will appear. Then the program will start.

t u

q w

Parts Names and Functions of the Screen

q Search PJ button

Search the projector connected to the networks.

w Specify IP button

When connected to a different segment network, the projector can not be retrieved automatically.

In that case, press this button, and then, the "Search specified IP address" window appears, and enter the IP address directly to specify the projector.

e Network Projector List

Display all the projectors connected to the networks. Show unoccupied projector as “On standby” and occupied projector as “Real time capturing” or "In

One-shot mode". When registered in a moderator’s group, "On Moderator mode" will be shown. The indication of the status of use with "#" indicates that your computer is now using the network capture function.

After double-clicking on a projector, the web browser gets activated and the projector setup screen

will be displayed.

Note on Windows Vista

When you use the Network Capture 5 software with Windows Vista, the warning dialog "User account control" will appear. In that case, click Allow button to use it.

Chapter 3 Names and functions of the operating screen

r Start communication button Enter the Communication mode, and then , the capture edit window starts. The selected projector

shows the capture edit window. t Start real time capture button Capture (Project) the computer screen in real time. After the execution of "Start real time capture",

the application window disappears. y Terminate capture button Terminate the real time capture and the One-shot capture. u One-shot capture button Copy and capture (project) the computer screen without modification. After the execution of One-

shot capture, the application window disappears. i Wireless easy setting button Configure the Wireless LAN setting just by clicking this button. ( The setting will be stored as AdHoc

system) For details, refer to "5. Wireless LAN configurations"-->"Easy wireless setting" (p.39). To

restore the easy setting, press the Wireless easy setting button. o Moderator registration button Register a computer user as a moderator. !0 Join moderator's group button Join the moderator's group which is selected in the Network Projector list. It is not available if there

is no moderator registered. !1 Parameter setup button Activate the parameter setup window, and execute the connections setting, the image setting, and

the moderator's function setting. For detail, refer to "Parameter set up" (p.88). !2 Select capturing object button It is possible to designate the window to capture individually. This button is disabled by default,

so the full screen is captured. It is possible to change the capturing object function setting at

parameter settings. For detail, refer to "Parameter set up" (p.88). !3 Volume adjust slider and Mute check box Adjust the audio output from the real time capturing computer. The mute check box is checked by

default.

Using the multiple network adaptors

When your computer provides multiple network adaptors, the network adaptor selecting window will appear each time the Network Capture 5 software starts. Select a network adaptor and check the "Select a network adaptor as default" and then click OK. To change the setting, refer to the item "Parameter set up" (p.88).

4. Wired LAN configurations

This chapter describes the preparation for Wired LAN setting with projectors and how to set the LAN environment.

Chapter

Chapter 4 Wired LAN configurations

Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately.

Connecting to the LAN line

Connect the LAN cable to the LAN connection terminal of the projector.

LINK/ACT Lamp (Orange)

LAN Connection Terminal

LAN Cable

* When the LAN setting is “Off ”, the two lamps

will not be on.

Light or blink orange when the projector is connected to the network.

Speed Lamp (Green) Light according to the speed of the connected network.

10 Base-T.........Off

100 Base-T ...... On

Network environment settings

Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “6. Basic setting and operation” (p43-62). First, complete the settings described in this chapter before performing steps in “6. Basic setting and operation.”

Setting Procedure

1. Turn on the projector and select “Wired” from the input menu of the projector.

The projector’s LINK/ACT Lamp will be on or blink. If the “Wired setting” is “Off”, it will not be on. Follow step 2 and 3 to blink the lamp.

2. Select “Wired Setting” in the projector menu, and press SELECT button.

Select similar LAN environment among LAN1, 2 and 3 with the Point 7 8 buttons. (LAN1, 2, and 3 are the factory default setting environments. You can select three different environment among setting LAN1–3. For each setting, refer to the chart on page 31.) When selecting “Off” in the “Wired setting”, the LAN connection will be cut off. Use the function when disconnecting the projector from the network.

3. Press the Point 7 8 buttons then the “Please wait...” message will appear and switching operation

will start. Switching will take a while and after completing the operation, the “Ready for use” message will appear. During the switching period, the projector cannot be operated.

Network environment setting

4. Press SELECT button. LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the

setting environment. Consult your system administrator about the detailed settings.

Adjust the figures with the Point ed buttons and move among the items with the Point 7 8

buttons.

5. After completing all the settings, select “Set” and press SELECT button. Now, all procedures have been done. To cancel the adjusted settings, select "Cancel" and press SELECT button. To confirm whether the settings are correct, follow the procedures described from the next page. You can confirm the LAN settings you have made from “Network Information” (p.30). In such cases that the LAN cannot be connected, see this screen.

Wired setting

Network PIN code

Wired LAN setting screen (Example)

Item Description

DHCP .......................... Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When

it set On, IP address, Subnet, Gateway and DNS are automatically set according to your network

environment *1.

IP address .................Sets IP address of the projector

Subnet .......................Sets Subnet mask. Normally sets 255.255.255.0

Gateway*2 .................Sets IP address of the default gateway (Router)

DNS*2.......................... Sets IP address of the DNS server.

*1 Set "On" only when the DHCP server is available on your network environment. *2 Set [255.255.255.255] if the network does not provide the gateway (router). *3 Set [255.255.255.255] if you do not use the function E-mail alert. * While the network communication function (p.94) or moderator function (p.103) is to be executing, the menus

"Network capture", "Network viewer" and "Memory viewer" are displayed in gray.

Chapter 4 Wired LAN configurations

Confirming the operation

Confirm that the projector has connected to the LAN properly.

1. Activate “Network Capture 5” which is installed into the computer connected to the LAN .

2. After “Searching projector” message appears, the name of the projector* appears on the Network Projector List, then the network setting has completed properly.

When the name of the projector does not appear and error screen appears, the network has

not connected yet. Try searching again with the Search PJ button. If error screen appears again, reconfirm the LAN setting. When the projector is set in the location separated by the router, see next page.

When Firewall function (Anti-virus software) is effective, network projector may not be found. In that

case, disable the Firewall function and try searching again.

✳ If the projector is named, the name will be displayed. The name can be set with the following

procedures in “6. Basic setting and operation” ➔ “Initial setting” (p48) . If the projector is not named, IP address of the projector will be displayed.

Network Capture screen

Network Projector List

Search PJ button

Confirming the operation

When set up the projector in the location separated by the router and the segment is different;

Projector will not be found nor displayed. In that case, the projector needs to be searched directly by the IP address.

1. Press Specify IP button. "Search specified IP address" window appears.

2. Enter the IP address of projector and Click OK. Then, the projector will be added on the Network

Projector List of the application window.

Network Projector list

Specify IP button

"Search specified IP address" window

Chapter 4 Wired LAN configurations

Network PIN code

The Network PIN code is to restrict the access from the networks to the projector. After setting the Network PIN code, you need to enter it to operate the projector via the networks.

1. Select Network PIN code menu, and press SELECT button.

The Network PIN code screen will appear.

2. Set the Network PIN code.

Set the figures with the Point ed buttons and move to the next items with the Point 7 8 buttons. Select “Set” and press SELECT button to set. To cancel the preset Network PIN code, select “Cancel”. When you do not want to set the Network PIN code, set "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See “6. Basic setting and operation” ➔ “Initial setting” ➔ “Network PIN code setting” (p49).

Network PIN code

Network PIN code screen

Network information

Wired factory default

Network information

Select Network information from the projector menu and press SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what will be shown.)

MAIN PROGRAM: V1.000 MAC ADDRESS: 08007B650056 IP ADDRESS: 172.21.95.202

Wired factory default

Select “Wired factory default” from the projector menu and press SELECT button. All the wired LAN settings will go back to the factory default settings. For details, refer to “Wired LAN factory default settings” (p.31).

(See the menu above.)

Network information

(See the menu above.)

+ 114 hidden pages