EnglishFrançaisEspañolDeutschItaliano
日本語
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Do not make any changes or modifications to the equipment unless otherwise specified in the
instructions. If such changes or modifications should be made, you could be required to stop operation of
the equipment.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
The CE Mark is a Directive
conformity mark of the European
Community. (EC)
LASER POINTER REMOTE CONTROL UNIT
Operating Instruction
MODEL POA-RCKIT03
FEATURES
This Remote Control Unit provides the Laser Pointer function. This function helps you to make a
smart presentation on a projected screen.
This Remote Control Unit has 2 different remote control codes ; the factory-set normal code (Code 1) and the
secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when
operating several projectors.
To change the code of the Remote Control Unit, press both the MENU and the IMAGE buttons together for
over 10 seconds. When batteries of the the Remote Control Unit are replaced, the remote control code
automatically returns to the normal code (Code 1).
Refer to the Owner’s Manual of your projector for switching the code of the projector.
Laser Pointer
Remote Control Code
SAFETY PRECAUTIONS
● Before operation, read this Instruction Manual thoroughly to operate properly.
● This Remote Control Unit emits laser beam from the Laser Light Window while pressing the LASER button (for 1
minute / The Signal Emission Indicator lights red to indicate the laser emission). Do not look into the Laser Light
Window or shine laser beam on yourself or the other people. Eye damage may result.
● If this Remote Control Unit is not to be used for an extended time, remove batteries.
●
For cleaning, use a soft, dry cloth. Do not apply benzene, thinner, splay or any chemical materials.
DO NOT OPEN AND ATTEMPT TO SERVICE INSIDE OF THE REMOTE CONTROL UNIT. THERE ARE
NO SERVICEABLE PARTS.
2
English
Execute the item selected, or
expand or compress the
image in the Digital zoom +/mode.
POWER ON-OFF
button
Turn the projector on or off.
Open or close the On-Screen
Menu.
LASER button
Operate the Laser pointer
function. The Laser beam is
emitted while pressing this
button within 1 minute. When
using this laser pointer for
more than 1 minute, release
the LASER button and press it
again.
Select an item or adjust the
value in the On-Screen Menu.
These are also used to pan the
image in the Digital zoom +/mode. The POINT 7 8 buttons
are also used as the VOLUME
+/- buttons.
POINT (VOLUME+/-)
buttons
Operate the P-Timer function.
Light red while the laser beam is
emitted from the Laser Light
Window or the signal is being
sent from the remote control unit
to the projector.
SIGNAL EMISSION INDICATOR
P-TIMER button
SELECT button
FREEZE button
Freeze the projected picture.
IMAGE button
Select image levels.
NO SHOW
button
Turn the picture into black
image.
Correct keystone distortion.
MUTE button
Mute the sound.
KEYSTONE
button
D.ZOOM buttons
Select the Digital zoom +/–
mode and resize the image.
MENU button
NAME AND FUNCTION OF EACH BUTTON
English
COMPUTER button
Select the input source (COMPUTER).
VIDEO button
Select the input source
(VIDEO).
Turn page; the Up button to
the previous page and the
Down button to the next page
for an image from a computer.
Connect the projector and
your computer with a USB
cable before use.
PAGE buttons
AUTO PC button
Operate the Auto PC adjustment function.
Note : For detailed operation, refer to the projector owner's manual.
3
LASER POINTER FUNCTION
REMOTE CONTROL BATTERY INSTALLATION
Specifications are subject to change without notice.
TECHNICAL SPECIFICATIONS
AAA, SUM-4 or LR03 Type x 2
Power Source
16.4’ (5m) / ±30˚
Operating Range
1.8” x 1.0” x 5.7” (45mm x 25mm x 145mm)
Dimensions
0.22 lbs (99 g) (including batteries)
Net Weight
Class II Laser (Max. Output : 1m W / Wave length : 640-660nm)
Laser Pointer
This remote control emits a laser beam from the Laser Light Window. With the LASER button pressed, the laser light goes
on. The signal emission indicator lights red and the laser is emitted with red light. With the LASER button pressed for more
than 1 minute or released, the light goes off.
To lock this function, press both the MENU button and the NO SHOW button for more than 10 seconds. To unlock, press
the MENU button and NO SHOW button again for more than 10 seconds.
The laser emitted is a class II laser. Do not look into the laser light window or shine the laser beam on yourself or other
people. The caution labels for laser beam are shown below.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure. Do not look into the Laser Light Window while the laser is emitted, otherwise
eye damage may result.
Laser Light Window
The caution label is put on the remote control.
Signal Emission Indicator
To insure safe operation, please observe the following precautions :
● Use (2) AAA, SUM-4 or LR03 type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture, or heat.
● Do not drop the remote control.
● If battery solution has leaked in the battery compartment, carefully wipe the compartment clean and install
new batteries.
● Risk of explosion if the battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions.
Press the lid downward
and slide it.
Remove the battery
compartment lid.
Slide the batteries into
the compartment.
Replace the compartment lid.
Two AAA size batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
1
2
3
4
English
Loading...