Sanyo POA-PN02 User Manual
OWNER’S MANUAL
PJ-Net Organizer plus
Model No. POA-PN02
Chapter 1 Preparation
Chapter 2 Installation
Chapter 3 Basic Setting & Operation
Chapter 4 Controlling the Projector
Chapter 5 Network Capture & Viewer
Chapter 6 Controlling the Multi-Projectors
Chapter 7 Use of Serial Port
Chapter 8 Appendix
This PJ-Net Organizer is an optional network product
for the projector. Mount this product to the projector
and connect a network cable. It enables a projector to
display the image data stored in the file server and the
screen image of the computer via the network. In addition, you can control and set up the projector remotely
by using the web browser.
This product is only used for SANYO projectors that
have a terminal for the PJ-Net Organizer.
This manual explains the installation of the PJ-Net
Organizer and its operation.
Compliance
Federal Communication Commission Notice
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be
required to stop operation of the equipment.
Model Numbers : POA-PN02
Trade Name : Sanyo
Responsible party : SANYO FISHER COMPANY
Address : 21605 Plummer Street, Chatsworth, California 91300
Telephone No. : (818)998-7322
SANYO POA-PN02
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
CAUTION ON USE IN NETWORK
- When you receive an alert e-mail from the projector, you must check the projector
immediately. Fire or accident may result if the projector is used in an abnormal
condition.
- When you install the projector at remote location and use it through the network,
you must perform the safety inspections periodically. In this case you must pay
attention to the change of environment in which you installed the projector. It may
cause fire or an accident depending on the change of environment.
CAUTION
SANYO Electric Co. Ltd assumes no responsibility for the loss or damage of data or
damage of the computer caused by use of this product.
2
Contents
Chapter 1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Software License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Chapter 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Flow of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Name and function of each part . . . . . . . . . . . . . . . . . . . . . . . . . .15
Installation and Network configuration . . . . . . . . . . . . . . . . . . . . .16
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connection of LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Password setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Notice about system construction . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Network Viewer & Capture installation . . . . . . . . . . . . . . . . . . . . . . . .22
Installed software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
File Converter 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Installed software and places . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Chapter 3 Basic Setting and Operation . . . . . . . . . . . . . . . . . .25
Login the setting page of the projector . . . . . . . . . . . . . . . . . . . .26
1 Enter the IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
2 Select a display mode and login . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
3 Display of main setting page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
1 Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2 Password Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3 Temperature unit setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4 Date/Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
1 Configure the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
2 Name the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
E-mail Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Examples: Type and contents of alert mail . . . . . . . . . . . . . . . . . . . . .35
Chapter 4 Controlling the Projector . . . . . . . . . . . . . . . . . . . . .37
Power on/off the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Check the status of projector . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Control the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
PC Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Save a Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Load a Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
System Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Save an image adjustment value . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
ENGLISH
Network Unit
OWNER’S MANUAL
3
Contents
Load an image mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
How to set the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Check the Timer events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Cancel the timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Save Actual Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Check the Save items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Control the projector's menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Make a memo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Chapter 5 Network Viewer & Capture . . . . . . . . . . . . . . . . . .59
Using the Network Capture function . . . . . . . . . . . . . . . . . . . . . .60
Launching the Network Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Parameter Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Advanced using example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Create the available data [File Converter] . . . . . . . . . . . . . . . . . . .65
[1] How to use the Network Viewer (File Converter 1) . . . . . . . . . . . .65
Converting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
[2] How to use the Network Viewer (File Converter 2) . . . . . . . . . . . .68
Conversion procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Making a program file [Program Editor] . . . . . . . . . . . . . . . . . . . .69
Procedure of making program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Using the Network Viewer function . . . . . . . . . . . . . . . . . . . . . . .72
Chapter 6 Controlling the Multi-Projectors . . . . . . . . . . . . . .79
Multi-Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Register IP address and projector name . . . . . . . . . . . . . . . . . . . . . . .81
Check IP address and projector name . . . . . . . . . . . . . . . . . . . . . . . .81
Exclude/Add/Delete a projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Load and apply the setting value . . . . . . . . . . . . . . . . . . . . . . . . .83
Chapter 7 Use of Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Serial Port setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Control Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Use of Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Control the projector with Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Chapter 8 Appendix:A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Examples of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Web browser setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Product specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
4
Chapter 1
Preparation
1
Network Unit
OWNER’S MANUAL
ENGLISH
5
Chapter 1 Preparation
Features
Network Capture function
It enables a projector to project the screen image of the computer on the screen via
the network by using an exclusive utility software .
PC1
PC2
PC4PC3
Internet
Intranet
Capture
PJ2 PJ1
PC5
Project a screen
image of PC1 with
PJ2.
Network Viewer function
The projector receives the image data stored in the file severs in the network and displays images automatically.
PC1
Prog.
JPEG
PC2
PC4PC3
Internet
Intranet
JPEG
PJ2 PJ1
PC5
Project JPEG images
stored in PC3 with PJ2.
* ftp file servers
6
Features
Web Management function
With this function, you can monitor projector functions such as power status, lamp
status, input mode, signal condition, lamp-use time, etc. through the network by using
the web browser installed on your computer.
PC1
PC2
PC4PC3
Tu rn on PJ2.
Internet
Intranet
PJ2 PJ1
PC5
E-Mail Alert function
The projector (Network Unit) sends messages to the registered e-mail addresses
when a lamp abnormality or power failure occurs with the projector. This message
describes how to solve the cause of the problems. You can take efficient action for
quick recovery.
PC1
PC2
PC4PC3
Internet
Intranet
PJ2 PJ1
PC5
You've got
Mail.
ENGLISH
Network Unit
OWNER’S MANUAL
7
Chapter 1 Preparation
Multi-control function
A single computer can control and set up the multiple computers at the same time.
PC5
PJ2 PJ1PJ4 PJ3
Select Input2
for PJ1 to PJ4
PC4PC3
Internet
Intranet
Automatic On/Off using Clock function
Automatically turn on or off the projectors at specified date/day and time by using the
clock function.
I am ready to turn ON,
and select Input 3 (Video)
Now it's 11:30
Control port ready for external equipment via network
This product provides a serial port (RS-232C) for controlling external equipment. By
connecting the equipment which has a serial port, it can be controlled by a computer
via the network. * This product does not provide the interface driver software to control external equipment.
PC1
PC2
Tu rn on the DVD player
and start playing.
PC4PC3
Internet
Intranet
PJ2 PJ1
PC5
DVD Player
8
Operating Environment
Operating Environment
To perform the managing and setting of the projector by using this product, the environment described below is required.
Network
Network must handle Ethernet correctly and accept TCP/IP and FTP protocol.
Operating System
Windows 98 / Windows 2000 / Windows Me / Windows NT4.0 SP6 / Windows XP
Computer system requirements
● Computer with 900 MHz or higher processor clock speed recommended;
* Intel Pentium/Celeron family or compatible processor recommended
● 128 MB of RAM or higher recommended (64 MB minimum supported)
● 100 MB of available hard-disk space
● VGA or higher-resolution video adapter and monitor
● CD-ROM drive
●10Base-T or 100Base-TX network card
Web browser application*
● Microsoft Internet Explorer version 5.0, 5.5 or 6.0.
● Netscape Navigator version 6.1, 6.2 or 7.0.
* Used to control and set up the projector. The layout of pages in the browser may slightly
differ from each type of application or operating system you use.
Internet mail application*
● Microsoft Outlook ● Microsoft OutlookExpress
● Netscape Mail
* Required the internet e-mail application software to receive an e-mail alert sent from this
product. If you do not use the function E-mail Alert, this application is not required.
File service*
● ftp server (Windows 2000 Professional or Windows XP Professional)
* The ftp service provided with the Windows 2000 Professional or Windows XP
Professional is required when using the Network Viewer function.
Network Unit
OWNER’S MANUAL
ENGLISH
9
Chapter 1 Preparation
The limitation*1of connection between this product and Hub or
Computer
Suitable LAN cables are limited by length and type as follows;
Connection Type of usable LAN cable Maximum length
Network Unit - Hub UTP Straight Cable with category 3 or 5 *
Network Unit - Computer UTP Cross Cable with category 3 or 5*
*1 There may be other limitations depending on your network environment or LAN specifica-
tion. Please consult your network administrator for further details.
*2 Category of LAN cable indicates the cable quality. Normally, a cable with category 3 or 5 is
used for 10Base-T network, and a cable with category 5 is used for 100Base-TX network.
2
2
100m
100m
Before use
Package contains
The package contains following items. Check each item as you unpack the package.
If you have any of the following items missing, contact the sales dealer.
10
❑ Network unit 1 piece
❑ Owner’s manual English/Japanese 1 piece each
❑ CD-ROM 1 piece
Expression
Expression/Abbreviation
The word “projector” found in this manual means “projector provided with Network
Unit” unless otherwise noted.
The OS of the computer and the Web browser described in this manual is Windows
XP Professional and Internet Explorer 6.0. In case of another OS or Web browser,
some instruction procedures may differ from the actual operation depending on your
computer environment.
Use of this manual
This manual does not provide the description of basic operation and functions for
computer, web browser, projector and network. For instructions about each piece of
equipment or application software, please refer to the respective booklet.
Trademarks
Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows,
Windows NT are registered trademarks of Microsoft Corporation. Internet Explorer is
a registered trademark of Microsoft Corporation. Netscape Navigator and Netscape
Communicator are trademarks or registered trademarks of Netscape Communications
Corporation. JavaScript is a registered trademark of Sun Microsystems, Inc.
Other product or brand names in this manual are registered trademarks or trademarks of their respective owners.
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
Network Unit
OWNER’S MANUAL
ENGLISH
11
Chapter 1 Preparation
Software License Agreement
Before using Network Viewer & Capture Software CD-ROM, thoroughly read the following
software license agreement to fully understand its contents.
Use this CD-ROM only when you agree to the terms of this agreement.
If you do not agree to the terms, do not use this CD-ROM.
Software License Agreement
This is a legal agreement between the customer (hereafter referred to as "user") and Sanyo
Electric. Co Ltd. (hereafter referred to as "our company"). Both parties accept the following terms
on use of this software product (hereafter referred to as "software") that our company grants to
the user the right to use the software.
Article 1 Definition of software
"Software" in this agreement includes computer software contained in this CD-ROM.
Article 2 Grant of license
Our company grants to the user the non-exclusive right to use the software on the following
terms and conditions stated in this agreement.
Article 3 Duplication of software
The user may not duplicate all or a part of the software except that the user may make a copy of
the software for backup purpose.
Article 4 Modification of software
The user may not decompile, disassemble, reverse engineer, or in any way modify the program
code of the software.
Article 5 Proprietary right and copyright
All of the copyright and proprietary right of the software and its copies belong to our company.
Article 6 Prohibition of regrant and transfer of the license to any third party.
The user may not transfer the program or its copy to any third party without the express written
permission from our company, or may not transfer or regrant the right to use the software.
Article 7 Contract term
This contract will commence on the date when the user starts using the software and shall be
effective until the user finishes using the software.
However, our company shall have the right to deprive the user of the right to use the software
and terminate the contract if the user is in the material breach of any term of this agreement.
Article 8 Obligations after contract termination
When the user terminates the contract, the user shall be responsible for making the software
obsolete and dispose of it so that a third party cannot re-use it. The user shall also dispose of all
duplicated or modified software and all documented materials about the software.
Article 9 Responsibilities of our company
In no event will company be liable to the user for direct, incidental or consequential damages, or
other property damages, such as data and program damages, including any loss of profits or lost
savings arising from use of the software made by the user.
12
Chapter 2
Installation
2
Network Unit
OWNER’S MANUAL
ENGLISH
13
Chapter 2 Installation
Flow of installation
The following are instructions for attaching this product to the projector and connecting it to the network. Please review the entire procedure to become familiar with it.
Function of the Network Unit (☞ p.15)
1
Explains the name and functions of each part of the network unit.
Installation and network configuration (☞ p.16-21)
2
1 Mount this product onto the projector.
2 Connect the LAN cable and join it to the network.
3 Configure the network of the network unit.
4 Set the password.
Installation of the software (☞ p.22-24)
3
Explains how to install the software Network Viewer & Capture into your computer.
Set up is completed.
The preparation is completed to control the projector connected to the network. At next
step, set up and control the projector via the network by using the web browser installed
on your computer. Please see chapter 3 “Basic setting and operation”. (☞ p.25)
14
z Name and function of each part
Power indicator
This lights up red when the net-
work function is set ON in the
projector menu.
Serial port
This is used when controlling
the external equipment via the
network. (☞ p.85)
Name and function of each part
Connecting the LAN cable.
LAN port
(☞ p.17)
Connector
plug
Connecting to the
terminal on the
projector. (☞ p.16)
Mounting
screws
Mount by using a
coin etc. (☞ p.16)
LINK indicator (Orange)
This lights up orange when the
Network Unit is connected to the
network correctly.
ACT indicator (Green)
This turns on and off when sending or receiving of data
ENGLISH
Network Unit
OWNER’S MANUAL
15
Chapter 2 Installation
x Installation and Network configuration
Mounting
1 Disconnect the AC plug from the
projector.
Connector cover
2 Remove the connector cover
and screw covers from the projector and insert plug on this
product to the option connector.
Screw cover
3 Tighten two screws by using a
coin etc.
!
Caution
✐ The AC cord must be disconnected when mounting or removing this product otherwise it
may damage the product.
✐ Do not connect the AC cord until after connecting the LAN cable and computer.
16
Connection of LAN cable
Connection of LAN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair)
strait cable with RJ-45 plug. There are two different types of cables depending on
whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub
(10Base-T or 100Base-TX) to distribute the network cable if required.
1 Disconnect the AC plug from the projec-
tor.
2 Connect the UTP strait cable to the LAN
port on the Network Unit.
3 Connect the UTP strait cable to the hub.
Hub
(10Base-T, 100Base-TX)
Projector
UTP strait cable
✐ Use the UTP cross cable when you connect the computer and projector directly not using the
hub.
✐ When you connect the projector into the 10Base-T network, use cable with category 3 or 5.
When you connect the projector into the 100Base-TX network, use cable with category 5.
✐ The length of cable between hub and projector should be less than 100m.
Network Unit
OWNER’S MANUAL
ENGLISH
17
Chapter 2 Installation
Network configuration
Confirmation of the network menu
When installing this product to the projector, the network on-screen menu items for
this product are activated automatically. If not activated, the product may not have
been installed correctly. Please check item “Mounting” (☞ p.16).
Configure the network
When you connect the projector to the network, the network number of projector
must be the same as the network you intend to connect. You should configure projector’s network first.
This example explains how to set the following configuration.
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 0.0.0.0
The default network configuration is set as follows.
IP Address : 192.168.0.2
Subnet Mask : 255.255.255.0
Default Gateway : 0.0.0.0
DNS : 0.0.0.0
1 Selection of network menu [Network]
Turn on the projector and display the menu on the screen. Select the Network setting
icon from the main menu using the point buttons (d e 7 8). From the submenu,
select Network setting sub icon, then press SELECT button once. Check that the
mode is ”On”. If not, change mode to ”On” using the point buttons 7 8.
Network setting
* The above on-screen display may differ from
the actual display depending on the functions
of the projector you use.
18
Network configuration
2 Configuration for IP Address/ Sub net/ Gateway*/DNS*
Press SELECT button again, the following network setting menu appears on the
screen. Enter the specified network address.
How to enter the numbers
There are 2 ways to enter the numbers, one is by using the point buttons
(d e 7 8) on the remote control
handset or on the projector, the other
is by using the screen 10-key pallet by
which the numbers can be entered
directory. For further information see
next page.
3 Restart the Network Unit
Select Set with 78 keys and press SELECT button again. The network configu-
ration display disappears and the network unit begins restarting. It takes about 40
seconds. Do not turn off the mains switch during this period.
Completing of installation
Now the installation is completed. The IP address of this projector is set to
“192.168.1.201”.
* In the network environments not using a Gateway or Router, the Default Gateway address
should be set to [0.0.0.0]. If you do not use the functions E-mail or DNS server, it is also set
[0.0.0.0] for the DNS address.
Network Unit
OWNER’S MANUAL
ENGLISH
19
Chapter 2 Installation
Password setting
A password can be set to restrict access to the setting pages of the projector using
the web browser. The default password is set “0000” as no password.
Network setting
1 Use the projector’s menu and select the Network setting icon on the menu.
2 Select the Network setting sub icon from the submenu, and then press SELECT
button once. Check that the mode is “On”.
3 Select the Password sub icon and then press SELECT button once.
*The setting window appears. The numbers on the display indicates the current password.
4 Enter your desired number by using the point buttons on the projector or remote
control handset, and then select Set and press SELECT button.
*The password setting window disappears and the network unit begins restarting. It takes
about 40 seconds. Do not turn off the mains switch during this period.
*The password can be entered by using the screen 10-key pallet (☞ P.21).
How to enter the numbers with point buttons
To move the selection and change the value, use the point buttons (d e 7 8) on the
projector or on the remote control handset.
The point buttons 7 8 are used to select the column.
The point buttons d e are used to change the numbers up and down.
✐ Password setting must be done when you connect the projector to the network. This setting
is carried out through the projector’s menu and also it can be set through the network using
the web browser. For further information please refer to item “Initial Setting/Password setting” (☞ p.30).
✐ Valid characters for password are only 4 digits numeric numbers 0 to 9. The number “0000”
means no password set.
✐ This password is not to restrict the use of the projector. This password is to set the security
against the use of the projector through the network.
20
Network configuration
How to enter the numbers with the screen 10-key pallet
1. Select a column with a red frame by
using the point buttons 7 8 .
10-key pallet
2. Press SELECT button. The screen
10-key pallet appears on the screen.
3. By using the point buttons(d e 7
8), select numbers 0 to 9 and press
SELECT button. By repeating the
above to enter the complete number
on the column.
*To change the number in a column,
select “C” and press SELECT button
to clear the number in the column and then enter the number again.
Exit
4. After entering the number in the column, select a move key (7 8 e d) located on
the lower part of the pallet by using the point buttons and press
repeatedly to move the red frame.
SELECT button
5. Repeat steps 3 to 4 for entering all the network address.
6. After finishing, select “Exit” and press SELECT button. The 10-key pallet disap-
pears on the screen.
Notice about system construction
For installation of multiple projectors into the same network with
Network Unit.
Do not install multiple projectors with Network Units that have their default network
settings to the same network. The use of the Network Units which have the default
IP address set to the same network settings will cause IP addresses to collide and
create a malfunction. When you install multiple projectors into the same network,
configure the network with the following steps.
1. Change the IP address from the default IP address. To change the IP address, use
the network setting menu on the projector. Please see item “Network
Configuration” for further information (☞ p.18).
2. Make sure that there is no network equipment set with the same IP address in the
network before connecting to the network.
3. When installing other projectors, follow the above steps to change the IP address
and connect to the network.
In case of installing the projector with Network Unit into the network constructed with the DHCP/BOOTP server.
This Network Unit does not support the DHCP/BOOTP server. The static IP address
must be manually configured. To use this product in this network environment, set it
up so that the DHCP/BOOTP server does not assign the IP address configured to this
product for another device on the network. Please consult your network administrator for further information.
Network Unit
OWNER’S MANUAL
ENGLISH
21
Chapter 2 Installation
c Installing the software
It is required to install the software into your computer to use the Network Capture
function and Network Viewer function. Please install the software as follows.
Note:
To install the software into the computer with Windows 2000, Windows XP or
Windows NT, you should login with administrator rights. Before installation, make sure
that the other applications are closed, otherwise proper installation cannot be made.
Network Viewer & Capture installation
1 Set the supplied Network Viewer & Capture
CD-ROM into the CD-ROM drive of your
computer. Double click SetupTool.exe icon
in the “Tool” folder in the CD-ROM.
2 Select “English [United States]” from the
pull-down menu on the “Choose Setup
Language” window and click OK button
to start installing and then follow the
installation wizards.
22
As the “Software License Agreement“
will appear, read contents carefully and
click Yes button if you agree the license
agreement to proceed with installing.
Installing the software
Installed software
The following 3 software are installed on your computer.
● Network Capture:
Capture the displayed image of the computer and serve it to the projector via the
network.
This software is registered into “startup
folder” of the computer and the capture icon
stays on the task bar after booting the computer.
Capture icon
● Network Viewer (File Converter 1):
Converts the JPEG*1data format which can be projected with the projector from
the JPEG and BMP files.
● Network Viewer (Program Editor) :
This is a tool to make the programs which has a function to specify and order the
projecting JPEG image data stored in the file servers.
* To uninstall these software, use “Add/Remove Program” from the control panel.
*1 The data which can be projected by the projector is the JPEG format based on the ISO/IEC
10918.ITU-T recommendation T.81. There are several kinds of JPEG formats. To project the
JPEG images by using the Network Viewer function of the projector, the files need to be
converted to the optimized JPEG file by using the File Converter application software previously.
Network Unit
OWNER’S MANUAL
ENGLISH
23
Chapter 2 Installation
File Converter 2 Installation
1 Set the supplied Network Viewer &
Capture CD-ROM into the CD-ROM drive
of your computer. Double click
SetupDrv.exe icon in the “Driver” folder
in the CD-ROM.
2 Select “English [United States]”from the
pull-down menu on the language selection window and then click Install button
to start installing.
Installed software and places
Network Viewer (File Converter 2) is installed
in the “Printers and Faxes” folder in the
“Control Panel”.
● Network Viewer (File Converter 2):
This is a kind of the printer driver to convert
to the JPEG data optimized to project by
the projector from any of the documents
created by the application software.
* To uninstall this software, just delete the
“Network Viewer” icon from the “Printers and
faxes” folder.
24
Chapter 3
Basic Setting and Operation
3
Network Unit
OWNER’S MANUAL
ENGLISH
25
Chapter 3 Basic Setting and Operation
This chapter describes basic operations and settings for controlling the projector via a
network using this product. It is required that computer and projector be connected
to the network and the network address be properly configured.
Login the setting page of the projector
1 Enter the IP address
Launch the web browser installed in
your computer, enter the IP address into
the “Address” on the browser and the
press “Enter” key.
Enter the IP address that you configured in
item “Network Configuration”(☞ p.18). The default IP address is [192.168.0.2].
2 Select a display mode and login
This product provides 2 types of control mode, Graphic Mode and Text Mode as
the below. Select a proper mode to match your PC and network environment by
clicking on the text link.
26
Graphic Mode
Text Mode
If the setting page has set the password, the authentication window will appear.
In this case type “user” onto the User Name text area and the login password
onto the Password text area and then click OK button.
* The entering User Name must be “user” and it can not be
changed.
[Note]
When accessing the projector at first time or setting the no
password [0000], the auto-login will be performed and the next
main setting page is displayed.
Displays with 600 x 400 dots and
the menus and settings with
graphic icons. This mode is recommended for standard use.
Displays with 200 x 300 dots. This
mode is optimized for use of the
handheld computer, PDA, etc. It is
also convenient if the network
traffic is heavy.
Login the setting page of the projector
3 Display of main setting page
The following main setting page will be displayed according to your display mode
selection. Perform the various kinds of setting through this page. Click on the
menus to display the control and setting pages.
z Main setting page in the Graphic Mode display
Setting page number
Browses pages by
clicking the linked
number.
Main menu
For selection of control and setting items of the projector.
(☞ p.37)
Setting page
Displays the control and setting
items according to the selected
menu. The “Power & Status”
page is displayed as the default.
* This graphic mode display is mainly used through this manual for the setting and
control description.
Network Unit
OWNER’S MANUAL
ENGLISH
27
Chapter 3 Basic Setting and Operation
x Main setting page in the Text Mode display
Main menu
For selection of control
and setting items of the
projector. Displays sub
menu and status of
selected items when
clicking the linked text.
Returns to the display mode
selection page.
Setting page number
Browses pages by clicking the linked number.
Setting page
Displays the control and
setting items according
to the selected menu.
The network viewer function in the text mode has following limitation;
- Cannot select the program or folder for the display (☞ p.73)
- Cannot perform the registration, check or change of the program (☞ p.75-76).
28
Initial Settings
Initial Settings
After installing this product to the projector, perform the following basic ini-
tial setting.
Click Initial Setting on the main menu to display the initial setting page.
The Languages, Date/Time, Password and Temperature unit can be set in this page.
The model name of the projector on which this product is mounted is displayed on
the page.
1 Language Setting
Projector’s
model name is
indicated.
This setting is to select the display language of the web page. Select your language with the pull-down menu button and then click Set button. The selectable
language is English or Japanese. You may find the unrecognized character text in
the menu if the computer does not provide Japanese fonts.
[Note]
This language selection is realized by using the JavaScript function of the web browser. If the
preference of the browser is set not to use the JavaScript, “Set” linked text appears on the
page as the below. Click on its text to change the language display. There are various kinds of
ways to change this preference depending on the web browser's version and application.
Please refer to item “Appendix: Web browser setting/Active Script (JavaScript enable)”.
(☞ p.96)
Network Unit
OWNER’S MANUAL
ENGLISH
29
Chapter 3 Basic Setting and Operation
2 Password Setting
This page is to set the password to restrict the access from an unauthorized person through the network.
Enter the password onto the text box and click Set button.
The Network Unit begins restarting and it takes about 40 seconds. Close (Quit) the
web browser and access to the login page again in 40 seconds. This is to perform
the login authentication firmly.
The default password [0000] means no password. When you connect the projector with this product to the network, it is recommended that you set a new password. Only a four-digit numeric number is valid for the password.
* If you forget the password to the projector, you can check it by selecting “Password” sub
menu from “Network setting” menu on the projector. For further information, please see
item “Password Setting”.(☞ p. 20)
3 Temperature unit setting
Change the temperature unit displayed on the Power & Status page by using the
pull-down menu.
Centigrade : indicated with ºC
Fahrenheit : indicated with ºK
*The projector icons shows the
thermal sensors inside the projector. For further information see
item “Check the status of projector” (☞ p. 39).
!
Caution
Use of Battery
This product provides a lithium battery. When the battery runs down, the clock and timer functions do not operate properly. Contact your local dealer for the replacement of battery. The
replacement must be carried out by a qualified service personnel.
30
Loading...