Sanyo POA-PN01 User Manual

OWNER’S MANUAL

PJ-Net Organizer

Model No. POA-PN01

Preparation

Installation

Basic Setting and Operation

Controlling the Projector

Controlling the Multi-Projectors

Controlling External Equipment

Appendix

INSTALLATION and OPERATION of the PJ-Net Organizer

This PJ-Net Organizer is an optional product to control and set up a projector via a network. Attach this product to the projector and connect a network cable. By accessing the connected projector using the web browser on your computer, the projector can be controlled and set up remotely. This product is only used for SANYO projectors that have a terminal for the PJ-Net Organizer. This manual explains the installation of the PJ-Net Organizer and its operation.

Preparation

Compliances

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers : POA-PN01 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91300 Telephone No. : (818)998-7322

SANYO POA-PN01

Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

Trademark

PJ-Net Organizer is a trademark of Sanyo Electric Co., Ltd. Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows NT are registered trademarks of Microsoft Corporation. Macintosh, Mac OS are registered trademarks of Apple Computer Inc. Internet Explorer is a registered trademark of Microsoft Corporation. Netscape Navigator and Netscape Communicator are trademarks or registered trademarks of Netscape Communications Corporation. JavaScript is a registered trademark of Sun Microsystems, Inc. Other product or brand names in this manual are registered trademarks or trademarks of their respective owners. * Unauthorized use of a part or whole of the contents in this manual is prohibited. * The contents of this manual are subject to change without notice.

Preparation

Expression/Abbreviation

The following abbreviations may appear in this manual:

● Windows 95, Windows 98, Windows 2000,

Windows Me, Windows XP, Windows NT4.0 ➜ Windows

● Macintosh, Power Macintosh ➜ Macintosh

● Mac OS 8 or later ➜ Mac OS

In some cases, the “PJ-Net Organizer” is explained as “this product” or “Network Board” in this manual. The word “projector” found in this manual means “projector provided with PJ-Net Organizer” unless otherwise noted.

Use of this manual

This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective booklet.

CAUTION ON USE IN NETWORK

- When you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition.

- When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector. It may cause fire or an accident depending on the change of environment.

CAUTION

SANYO Electric Co. Ltd assumes no responsibility for the loss or damage of data or damage of the computer caused by use of this product.

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Flow of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Name and function of each part . . . . . . . . . . . . . . . . . . . . . . . . . .11

[1] Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

[2] Connection of LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

[3] Confirmation of network menu activity . . . . . . . . . . . . . . . . . .14

[4] Network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Configure the network with the projector . . . . . . . . . . . . . . .16

Configure the network with the computer . . . . . . . . . . . . . . .18

Configure the network of computer . . . . . . . . . . . . . . . . . . . . . . .20

Windows 98/85/Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Windows 2000/NT4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Notice about system construction . . . . . . . . . . . . . . . . . . . . .24

Basic Setting and Operation . . . . . . . . . . . . . . . . . .25

1 Enter the IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

2 Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

3 Display of main setting page . . . . . . . . . . . . . . . . . . . . . . . .27

4 Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

1 Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

2 Date/Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

3 Password Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

1 Configure the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

2 Name the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

E-mail Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Examples: Type and contents of alert mail . . . . . . . . . . . . . . .32

Controlling the Projector . . . . . . . . . . . . . . . . . . . . .33

Power on/off the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Check the status of projector . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Control the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

PC Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

SYSTEM Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

How to set the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Cancel the timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Save Actual Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Control the projector's menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Controlling the Multi-Projectors . . . . . . . . . . . . . . .49

Multi-Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Exclude/Add the projectors from/into the multi-control . . . . .51

Add all of listed projectors into multi-control . . . . . . . . . . . . .51

Delete from the multi-control list . . . . . . . . . . . . . . . . . . . . . .51

Load and apply the setting value . . . . . . . . . . . . . . . . . . . . . . . . .52

Control multi-projectors at the same time . . . . . . . . . . . . . . . . . .52

Selection of another projector . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Controlling External Equipment . . . . . . . . . . . . . . .55

Control Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Control Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Serial port setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Use of Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Contents

Appendix:A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Examples of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Peer-To-Peer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

The gateway (Router) installed in the network . . . . . . . . . . . .63

Web browser setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Cookies enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Active Script/JavaScript enable . . . . . . . . . . . . . . . . . . . . . . .64

Proxy setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Setting examples: OS/Browsers . . . . . . . . . . . . . . . . . . . . . . . . .65

Windows 95/98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Mac OS 8.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Product specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Port Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Appendix:B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Preparation

Features

Web Management function

With this function, you can monitor projector functions such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer.

Power ON !

E-Mail Alert function

Projector (PJ-Net Organizer) sends messages to the registered e-mail addresses when a lamp abnormality or power failure occurs with the projector. In this message, it describes how to solve the cause of the problems. You can take efficient action for quick recovery.

You've got mail !

Features

Multi-control function

A single computer can control and set up the multiple computers at the same time.

3F Meeting Room 5F Show Room

Automatic On/Off using Timer function

Automatically turn on or off the projectors at specified date/day and time by using the clock function.

I am ready to turn ON, and select Input 3 (Video)

Now it's 11:30

Control port ready for external equipment via network

This product provides a serial port (RS-232C) for controlling external equipment. By connecting the equipment which has a serial port, it can be controlled by a computer via the network. * This product does not provide the interface driver software to control external equipment.

DVD Player

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Preparation

Operating Environment

To perform the management and setting up the projector using this product, the environment described below is required.

Operating System

Windows 95 / Windows 98 / Windows 2000 / Windows Me / Windows NT / Windows XP Mac OS 8.0 or later

Network

Network must handle Ethernet correctly and accept TCP/IP protocol.

Computer

The computer must provide a 10Base-T or 100Base-TX network card.

Web browser application*

● Microsoft Internet Explorer version 5.0 or later

● Netscape Navigator version 4.7 or later

* Use to control and set up the projector. The layout of pages in the browser

may slightly differ from each type of application or operating system you use.

Internet mail application*

● Microsoft Outlook ● Microsoft OutlookExpress

● Netscape Mail

* Required the internet e-mail application software to receive an e-mail alert sent

from this product. If you do not use the function E-mail Alert, this application is not required.

The limitation of connection between this product and Hub or Computer

Suitable LAN cables are limited by length and type as follows;

Connection Type of usable LAN cable Maximum length

PJ-Net Organizer - Hub UTP Strait Cable with category 3 or 5 100m

PJ-Net Organizer - Computer UTP Cross Cable with category 3 or 5 100m

✐ Category of LAN cable indicates the cable quality. Normally, cable with category 3 or 5 is

used for 10Base-T network and cable with category 5 is used for 100Base-TX network.

✐ There may be other limitations depending on your network environment or LAN specification.

Please consult your network administrator for further details.

Installation

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

Flow of installation

The following are instructions for attaching this product to the projector and connecting it to the network. Please review the entire procedure to become familiar with it.

Check package (p.11)

Please check the contents of a package. This product contains a network board and an owner’s manual (this manual). Also please check the name and function of each part.

Installation (p.12-14)

1. Mount this product onto the projector.

2. Connect the LAN cable and join it to the network.

3. Confirm that the network menus are activated on the setting menu of the projector.

Network configuration (p.15-24)

Configure the network of the projector. Separate configurations must be set up for each network to which the projector will be connected.

☛ Configure the network with the projector. ☛ Configure the network with the computer.

Setting up is completed.

The preparation is completed to control the projector connected to the network. At next step, set up and control the projector via the network by using the web browser installed on your computer. Please see chapter “2: Basic setting and operation” on page 25.

Name and function of each part

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

[1] Mounting

1 Disconnect the AC plug from the

projector.

2 Remove the connector cover

and screw covers from the projector and insert plug on this product to the option connector.

3 Tighten two screws by using a

coin etc.

Caution

✐ The AC cord must be disconnected from AC power outlet when mounting or removing this

product. It may damage the product.

✐ Do not connect the AC cord until after connecting the LAN cable and computer.

Connection of LAN cable

[2] Connection of LAN cable

To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) strait cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable if required.

1 Disconnect the AC plug from the projec-

tor.

2 Connect the UTP strait cable to the LAN

port on the network board.

3 Connect the UTP strait cable to the hub.

Hub (10BaseT, 100Base-TX)

Projector

UTP strait cable

✐ Use the UTP cross cable when you connect the computer and projector directly not using the

hub.

✐ When you connect the projector into the 10Base-T network, use cable with category 3 or 5.

When you connect the projector into the 100Base-TX network, use cable with category 5.

✐ The length of cable between hub and projector should be less than 100m.

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

[3] Confirmation of network menu activity

When installing this product onto the projector, the network on-screen menu items for this product are activated automatically. If not activated, the product may not have been installed correctly. Please check chapter “Mounting” on page 12.

Turn on the projector and display the menu on the screen.

Confirmation of network setting menu [PJ-Net Organizer]

Using the pointers on the remote control handset or on the projector, select the PJ-Net Organizer icon from the Setting sub menu, and then press the SELECT button once. Check if the setting is On. If not, switch to On by using the pointer / . The power indicator

▲

on this product will illuminate red. Press the SELECT button again, the network setting menu appears on the screen as follows. For further information about network setting, please see chapter “Network configuration”on next page.

Network Setting IP Address Subnet mask Default Gateway DNS

192 168 0 2 255 255 255 0

0000 0000

Confirmation of password setting menu [Display]

Using the pointers on the remote control handset or on the projector, select the Display icon from the Setting sub menu, and then press the SELECT button twice. The password setting menu appears on the screen. If not, please check if the function of PJ-Net Organizer is On as explained on previous item “Confirmation of network setting menu”. For further information about password setting, please see “Password setting menu” on page

17.

Password

0000

Network configuration

[4] Network configuration

When you connect a projector to a network, the network number of projector must be the same as the network you intend to connect. You should configure projector’s network first. Make sure that the projector is connected to the network correctly. There are 2 ways to configure the network, by using the projector’s menu using the computer

[B]. Refer to the chart below and use the method you prefer.

Procedure of Connecting the projector to the network

[A], or by

Configure the network with the

A B

projector

p.16

Tu rn the projector on and display the network setting menu on the screen.

Configure the network through the projector's menu.

Example of projector's configuration IP Address : 192.200.1.201 Subnet Mask : 255.255.255.0 Default Gateway : 192.200.1.1 DNS : 0.0.0.0

Restart the PJ-Net Organizer

Please see further informatin on pages 16-17.

Configure the network with computer

Temporarily set up the computer's network with the default network number of the PJ-Net Organizer.

Restart the Computer, if required

Using the web browser and login to the setting page of the PJ-Net Organizer by accessing the default IP address.

Change the network address you want to connect to the existing network through the setting menu on the browser.

Restart the PJ-Net Organizer

Reset to the computer's original network configuration.

p.18

Please see further informatin on pages 18-23.

Example of projector's configuration IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : (blank) DNS : (blank)

Please see further informatin on pages 25-30.

Default Network Address of the PJNetOrganizer IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0

Example of projector's configuration IP Address : 192.200.1.201 Subnet Mask : 255.255.255.0 Default Gateway : 192.200.1.1 DNS : 0.0.0.0

ENGLISH

Completing the network configuration. Perform the basic setting and operation of the projector by using the web browser. Please see chapter "Basic Setting" on page 25 for further information.

PJ-Net Organizer

OWNER’S MANUAL

Installation

Configure the network with the projector

This example explains how to set the following configuration.

Network configuration

How to enter the numbers

To move the selection and change the values, Use the pointers ▲/▼// on the projector or on the remote control handset.

The / keys are used to move the selection item.

▲

The ▲/ ▼ keys are used to change the number value.

3 Restart the Network board

Press the SELECT button again. The network configuration display disappears and the network board begins restarting* connect the AC cord from the projector.

. It takes about 60 seconds. Do not dis-

Completing of installation

Now the installation is completed. The IP address of this projector was set to “192.200.1.201”. Next, please see chapter “Basic setting and operation” on page

25. It describes basic setup and operation of the projector.

Password setting menu [Display]

A password can be set to restrict access to the setting pages of the projector using the web browser. The default password is set “0000” as no password. Use the projector’s menu and select the Display icon on the Setting sub menu, and then press the SELECT button on the projector twice. The following setting display appears on the screen. The numbers on the display indicates the current password. To change the password, enter your desired number by using the pointers on the projector or remote control handset, and then press the SELECT button. The password setting display disappears and the network board begins restarting* about 60 seconds. Do not disconnect the AC cord from the projector.

. It takes

Password

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

Configure the network with the computer

This example explains how to set the following configuration.

IP Address : 192.200.1.201 Subnet Mask : 255.255.255.0 Default Gateway : 192.200.1.1 DNS : 0.0.0.0

The default network configuration is set as follows.

IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0

Make sure that the projector is connected to the network and then connect the AC cord to the outlet.

1 Temporarily*

set up your computer network configuration to the same IP network

number as the PJ-Net Organizer. For example, change your computer network

configuration as follows and restart the computer.

IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : (blank) DNS : (blank)

The network configuration of computer differs depending on each network environment or your computer. For further information, please see the next chapter “Configure the network of computer”.

*1 Change your computer’s network configuration temporarily. After completing the set up for

the projector, you must set up again to the original network configuration for your computer. It is recommended to make a note of those network settings.

Network configuration

2 Configure the network of the projector by using the web browser.

1. Enter the IP address of the projector as the URL. The login page will be dis-

played and login. For further information, please see chapter “2: Basic Setting and Operation” on page 25.

2. Configure the network through the setting page on the browser. For further

information, please see chapter “Network Configuration” on page 30.

Completing of installation

Now the installation is completed. The IP address of this projector has been set to “192.200.1.201”. You must reset the network configuration of the computer to the original and restart the computer. Next, please see chapter “Basic Setting and Operation” on page 25. It describes how to operate and set up the projector .

✐ If you use a cable to connect the projector and computer directly, without using a hub, you

must use a UTP cross cable. In this case, you cannot access the login page if the setting of web browser is set to “Use proxy server”. It must be changed to the “Not use proxy server”. For further information, please see the “Web browser setting” on page 64.

✐ When you set up the network of projector which has a default setting by using the computer,

it must be carried out in the network which does not provide any gateways (routers). If it has the gateways (routers), you must carry out the configuration by using the projector’s menu.

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

Configure the network of computer

When you use the projector through the network, the IP address of the pro-

jector must be the same IP network number of the existing network. Also it is required to use the same IP network number of the computer to set up the projector. In the network included with the gateway (router), it must be used with the IP network number specified by the gateway (router).

Configure the computer's network by following steps:

Windows 98/85/Me

This example explains how to set the following network address.

IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1

1 Select the Control Panel menu from [Start] -

[Setting] menu.

2 Double click the Network icon on the control

panel window.

3 Select the TCP/IP*

Network Component" column on the "Network configuration" tab on the "Network" dialog window, and then press the Properties button.

4 Click IP Address tab, and then select the

Specified IP address. Enter the IP Address*

and Subnet Mask.

5 Click the Gateway tab and enter the Gateway

Address then press the Add button. Please make sure that the entered gateway address appears on the "Installed Gateway column.

✐ This setting is not needed if the network does not

provide the gateway (router).

6 Click the OK button, the setting window will

be closed and restart the computer.

item on the "Current

Configure the network of computer

Windows 2000/NT4.0

This example explains how to set the following network address.

IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1

1 Select the Network and Dial-up Connections

menu from [Start] - [Settings] menu.

2 Click the Local Area Connection icon with

right button of the mouse and then select the Properties menu from the popup menu. The right window will appear on the screen.

3 Select the Internet Protocol(TCP/IP)

on the General tab of the "Local Area Connection Properties" dialog window and then press the Properties button.

4 On the "Internet Protocol (TCP/IP) Properties"

dialog window, select the Use the following IP address button and then enter the IP

Address*

and Subnet mask.

5 Enter the Default gateway address.

✐ This setting is not needed if the network does

not provide the gateway (router).

6 Click the OK button, the setting window will

be closed.

✐ To change the configuration, you may need administrator privileges.

*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the col-

umn, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer.

*2 If the network already has the TCP/IP protocol set, enter with the same IP network number

for the IP address and Subnet mask.

*3 There are some ways to set up the network depending on your computer’s appearances.

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

Windows XP

This example explains how to set the following network address.

IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1

1 Select the Control Panel menu from the

[Start] menu. Click the Network and Internet Connection and then click the Network on

the control panel.

2 Click the Local Area Connection icon with

right button of the mouse and then select the Property menu. The right window will appear on the screen.

3 Select the General tab on the "Local Area

Connection Properties" dialog window. Select the Internet Protocol(TCP/IP) press the Properties button.

and then

4 On the "Internet Protocol (TCP/IP) Properties"

dialog window, select the Use the following IP address button and then enter the IP

address*

and Subnet mask.

5 Enter the Default gateway address.

✐ This setting is not needed if the network does

not provide the gateway (router).

6 Click the OK button, the setting window will

be closed.

*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the col-

umn, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer.

*2 If the network already has the TCP/IP protocol set, enter with the same IP network number

for the IP address and Subnet mask.

*3 There are some ways to set up the network depending on your computer’s appearances.

Configure the network of computer

Macintosh

This example explains how to set the following network address.

IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Gateway Address : 192.168.100.1

1 Select TCP/IP*

menu from the

[Apple] - [Control Panel] menu.

2 Select Ethernet from the "Connect

via" popup menu and Manually from the "Configure" popup menu of the TCP/IP Control Panel.

3 Enter the IP Address*

and Subnet

Mask.

4 Enter the Router Address.

✐ This setting is not needed if the net-

work does not provide the gateway (router).

5 Close the setting window and save

the setting.

*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the col-

umn, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer.

*2 It the network already has the TCP/IP protocol set, enter with the same IP network number

for the IP address and Subnet mask.

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Installation

Notice about system construction

For installation of multiple projectors onto the same network with PJNet Organizer.

Do not install multiple projectors with PJ-Net Organizers that have their default network settings to the same network. The use of the PJ-Net Organizers which have the default IP address set to the same network settings will cause IP addresses to collide and create a malfunction. When you install multiple projectors into the same network, configure the network with the following steps.

1. Change the IP address from the default IP address. To change the IP address, use the network setting menu on the projector. Please see chapter “Network Configuration” on page 15 for further information.

2. Make sure that there is no network equipment set with the same IP address in the network, and then connect to the network.

3. When installing other projectors, follow the above steps to change the IP address and connect to the network.

In case of installing the projector with PJ-Net Organizer into the network constructed with the DHCP/BOOTP server.

This PJ-Net Organizer does not support the DHCP/BOOTP server. The static IP address must be configured by the manual. To use this product in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP address configured to this product for another device on the network. Please consult your network administrator for further information.

Basic Setting and Operation

PJ-Net Organizer

OWNER’S MANUAL

ENGLISH

Basic Setting and Operation

This chapter describes basic operations and settings for controlling the projector via a network using this product. It is required that computer and projector are connected to the network and the network address be properly configured.

Login or logout the setting page of the projector

1 Enter the IP address

Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and the press the “Enter” key.

Enter the IP address that you configured in chapter “Network Configuration” on page 15. The default IP address is [192.168.0.2].

2 Login

The following login page appears on the browser. Type the password and press the Enter button. If you check the item “Save this password”, you will automatically login* without entering the password for the next login.

[Note] When accessing projector at first time or setting the no password [0000], the auto-login will be performed and the next main setting page is displayed.

✐ The function of "Save this password" uses the cookies function and JavaScript function of the

web browser. If you cannot automatically login even if the "Save this password " is checked, check your browser preference and change setting to "Accept all cookies" and “JavaScript Enable” if required. Please see chapter “Appendix: Web browser setting/Cookies enable, Active Script (JavaScript enable)” on page 64 for further information.

+ 58 hidden pages