How it Works
Sanyo
Loading...
P
Loading...
Loading...
PLV-WF20 - 6000 Lumens
User Manual
68 pgs604.78 Kb0

Sanyo PLV-WF20 - 6000 Lumens, PLV-WF20 User Manual

EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATIONS
PLV-WF20
SANYO Electric Co., Ltd
Personal Mobile Group
DI Company
Projector Division
PLV-WF20 Expand Serial Command Functional Specifications
2/68
CONTENTS
1． Overview ...................................................................................................................... 8
2． Serial Interface Specification ..................................................................................... 8
2.1 Transfer Specification............................................................................................... 8
2.2 Connection ................................................................................................................ 8
3． Notes for communication........................................................................................... 9
4． Notation...................................................................................................................... 10
5． Functional Execution Command Table.................................................................... 11
5.1 Image Command Table ........................................................................................... 11
5.2 PC Control Command Table................................................................................... 11
5.3 Input Control Command Table ............................................................................... 11
5.4 Screen Command Table..........................................................................................12
5.5 Lamp Command Table............................................................................................ 12
5.6 Setting Command Table ......................................................................................... 12
5.7 Other Command Table............................................................................................ 13
6． Status Read Command Table ...................................................................................13
6.1 Image Status Read Command Table......................................................................13
6.2 PC Status Read Command Table........................................................................... 13
6.3 Video Status Read Command Table ...................................................................... 13
6.4 Input Status Read Command Table ....................................................................... 14
6.5 Screen Status Read Command Table....................................................................14
6.6 Lamp Status Read Command Table....................................................................... 14
6.7 Setting Status Read Command Table.................................................................... 14
6.8 Other Status Read Command Table....................................................................... 15
7． Error Code Table........................................................................................................ 16
8． Functional Execution Command.............................................................................. 17
8.1 Format......................................................................................................................17
8.2 Transfer Example.................................................................................................... 17
8.3 Operation Requirements ........................................................................................ 17
8.4 Image Command .....................................................................................................18
8.4.1 CF_ CONT Command....................................................................................... 18
8.4.2 CF_ BRIGHT Command.................................................................................... 18
8.4.3 CF_COLOR Command ..................................................................................... 18
8.4.4 CF_TINT Command .......................................................................................... 18
8.4.5 CF_COLMNAV Command................................................................................. 19
8.4.6 CF_COLMNLD Command ................................................................................ 19
8.4.7 CF_APCTRL Command....................................................................................19
8.4.8 CF_COLTEMP Command................................................................................. 19
8.4.9 CF_WBAL- Command ...................................................................................... 20
8.4.10 CF_OFFSET- Command................................................................................. 20
PLV-WF20 Expand Serial Command Functional Specifications
3/68
8.4.11 CF_SHARP Command.................................................................................... 20
8.4.12 CF_GAMMA Command...................................................................................21
8.4.13 CF_NZRED Command.................................................................................... 21
8.4.14 CF_PROGV Command ................................................................................... 21
8.4.15 CF_IMAGE Command..................................................................................... 22
8.4.16 CF_IMAGEADJ Command ............................................................................. 22
8.5 PC Control Command.............................................................................................23
8.5.1 CF_FSYNC Command......................................................................................23
8.5.2 CF_TDOTS Command...................................................................................... 23
8.5.3 CF_H-POS Command....................................................................................... 23
8.5.4 CF_V-POS Command....................................................................................... 24
8.5.5 CF_CLAMP Command...................................................................................... 24
8.5.6 CF_DDOTS Command......................................................................................24
8.5.7 CF_DLINE Command........................................................................................ 25
8.5.8 CF_SETPCADJ Command ...............................................................................25
8.5.9 CF_ORGMODE Command ............................................................................... 25
8.5.10 CF_PCSTORE Command............................................................................... 26
8.5.11 CF_PCMODEFREE Command....................................................................... 26
8.6 Input Control Command......................................................................................... 27
8.6.1 CF_INPUT Command........................................................................................ 27
8.6.2 CF_SOURCE Command................................................................................... 27
8.6.3 CF_INPUT1~4 Command.................................................................................. 27
8.6.4 CF_SYSTEM Command.................................................................................... 28
8.7 Screen Control Command...................................................................................... 29
8.7.1 CF_SCREEN Command ................................................................................... 29
8.7.2 CF_DZCENT Command....................................................................................29
8.7.3 CF_KEYSTONE Command............................................................................... 30
8.7.4 CF_KEYSTONEMODE Command....................................................................30
8.7.5 CF_CEIL Command.......................................................................................... 30
8.7.6 CF_REAR Command........................................................................................ 31
8.7.7 CF_VSCALE Command....................................................................................31
8.7.8 CF_VPOS Command ........................................................................................ 31
8.7.9 CF_HSCALE Command.................................................................................... 32
8.7.10 CF_HPOS Command...................................................................................... 32
8.8 Lamp Command...................................................................................................... 33
8.8.1 CF_LAMPH Command...................................................................................... 33
8.8.2 CF_LAMPMODE Command ............................................................................. 33
8.8.3 CF_AUTOLAMPCONTRL Command...............................................................33
8.9 Setting Command ................................................................................................... 34
8.9.1 CF_LANG Command........................................................................................ 34
PLV-WF20 Expand Serial Command Functional Specifications
4/68
8.9.2 CF_DISP Command.......................................................................................... 34
8.9.3 CF_BACKGND Command................................................................................ 34
8.9.4 CF_LOGO Command........................................................................................35
8.9.5 CF_FANSPEED Command...............................................................................35
8.9.6 CF_RCODE Command ..................................................................................... 35
8.9.7 CF_RSENS Command...................................................................................... 36
8.9.8 CF_P-MANE Command.................................................................................... 36
8.9.9 CF_P-MANETIME Command............................................................................ 36
8.9.10 CF_ON-STA Command...................................................................................36
8.9.11 CF_PJPINCODE Command............................................................................ 37
8.9.12 CF_FILH Command ........................................................................................ 37
8.9.13 CF_FILTIMER Command ................................................................................ 37
8.9.14 CF_FILCTL Command.................................................................................... 37
8.9.15 CF_FILSCRL Command .................................................................................38
8.9.16 CF_TESTPAT Command................................................................................. 38
8.9.17 CF_FDEFAULT Command.............................................................................. 38
8.9.18 CF_KEYDIS Command................................................................................... 38
8.9.19 CF_SHUTRCPROT Command........................................................................ 39
8.9.20 CF_SHUTKEYPROT Command ..................................................................... 39
8.9.21 CF_SHUTH Command.................................................................................... 39
8.10 Other Command.................................................................................................... 39
8.10.1 CF_SHUTTER Command ............................................................................... 39
9． Status Read Command............................................................................................. 40
9.1 Format......................................................................................................................40
9.2 Transfer Example.................................................................................................... 40
9.3 Operation condition................................................................................................ 40
9.4 Image Status Read Commands.............................................................................. 41
9.4.1 CR_CONT Command........................................................................................41
9.4.2 CR_BRIGHT Command.................................................................................... 41
9.4.3 CR_COLOR Command..................................................................................... 41
9.4.4 CR_TINT Command..........................................................................................41
9.4.5 CR_APCTRL Command ................................................................................... 41
9.4.6 CR_COLTEMP Command................................................................................. 42
9.4.7 CR_WBAL-R Command ................................................................................... 42
9.4.8 CR_WBAL-G Command ...................................................................................42
9.4.9 CR_WBAL-B Command ................................................................................... 42
9.4.10 CR_OFFSET-R Command.............................................................................. 42
9.4.11 CR_OFFSET-G Command .............................................................................. 42
9.4.12 CR_OFFSET-B Command.............................................................................. 43
9.4.13 CR_SHARP Command ................................................................................... 43
PLV-WF20 Expand Serial Command Functional Specifications
5/68
9.4.14 CR_GAMMA Command.................................................................................. 43
9.4.15 CR_NZRED Command.................................................................................... 43
9.4.16 CR_PROGV Command................................................................................... 43
9.4.17 CR_IMAGE Command ....................................................................................44
9.4.18 CR_IMGGMD Command.................................................................................44
9.5 PC Status Read Commands................................................................................... 45
9.5.1 CR_FSYNC Command......................................................................................45
9.5.2 CR_TDOTS Command......................................................................................45
9.5.3 CR_H-POS Command....................................................................................... 45
9.5.4 CR_V-POS Command.......................................................................................45
9.5.5 CR_CLAMP Command .....................................................................................46
9.5.6 CR_DDOTS Command ..................................................................................... 46
9.5.7 CR_DLINE Command....................................................................................... 46
9.5.8 CR_SETPCADJ Command...............................................................................47
9.5.9 CR_ORGMODE Command............................................................................... 47
9.5.10 CR_PCSTORE Command............................................................................... 48
9.6 Video Status Read Command................................................................................48
9.6.1 CR_SERSYS Command ................................................................................... 48
9.7 Input Read Command............................................................................................. 49
9.7.1 CR_INPUT Command....................................................................................... 49
9.7.2 CR_SOURCE Command................................................................................... 49
9.7.3 CR_SYSTEM Command................................................................................... 50
9.7.4 CR_SRCINP1 Command .................................................................................. 51
9.7.5 CR_SRCINP2 Command .................................................................................. 51
9.7.6 CR_SRCINP3 Command .................................................................................. 51
9.7.7 CR_SRCINP4 Command .................................................................................. 51
9.7.8 CR_HMSLOT Command...................................................................................51
9.7.9 CR_NMSLOT1 Command.................................................................................52
9.7.10 CR_NMSLOT2 Command...............................................................................52
9.7.11 CR_NMSLOT3 Command...............................................................................52
9.7.12 CR_NMSLOT4 Command...............................................................................52
9.7.13 CR_IDSLOT1 Command.................................................................................52
9.7.14 CR_IDSLOT2 Command.................................................................................53
9.7.15 CR_IDSLOT3 Command.................................................................................53
9.7.16 CR_IDSLOT4 Command.................................................................................53
9.8 Screen Status Read Commands............................................................................ 54
9.8.1 CR_SCREEN Command................................................................................... 54
9.8.2 CR_KYSTNMODE Command........................................................................... 54
9.8.3 CR_CEIL Command..........................................................................................54
9.8.4 CR_REAR Command........................................................................................54
PLV-WF20 Expand Serial Command Functional Specifications
6/68
9.8.5 CR_VSCALE Command ................................................................................... 54
9.8.6 CR_VPOS Command........................................................................................55
9.8.7 CR_HSCALE Command ...................................................................................55
9.8.8 CR_HPOS Command........................................................................................55
9.9 Lamp Status Read Commands...............................................................................56
9.9.1 CR_LAMPREPL Command ..............................................................................56
9.9.2 CR_LAMPMODE Command............................................................................. 56
9.9.3 CR_AUTOLAMPCONTRL Command...............................................................56
9.9.4 CR_LAMPSTS Command.................................................................................56
9.9.5 CR_INFLAMP Command.................................................................................. 57
9.9.6 CR_PROJH Command...................................................................................... 57
9.9.7 CR_HMLAMP Command ..................................................................................57
9.9.8 CR_LAMPH Command .....................................................................................57
9.10 Setting Status Read Commands..........................................................................58
9.10.1 CR_BACKGND Command.............................................................................. 58
9.10.2 CR_DISP Command........................................................................................ 58
9.10.3 CR_LOGO Command ..................................................................................... 58
9.10.4 CR_LOGOLOCK Command ........................................................................... 58
9.10.5 CR_RCODE Command................................................................................... 58
9.10.6 CR_RSENS Command.................................................................................... 59
9.10.7 CR_LANG Command......................................................................................59
9.10.8 CR_ON-STA Command...................................................................................59
9.10.9 CR_P-MANE Command..................................................................................59
9.10.10 CR_P-MANETIME Command ....................................................................... 60
9.10.11 CR_FANSPEED Command...........................................................................60
9.10.12 CR_KEYDIS Command................................................................................. 60
9.10.13 CR_SHUTRCPROT Command..................................................................... 60
9.10.14 CR_SHUTKEYPROT Command................................................................... 60
9.10.15 CR_SHUTH Command.................................................................................. 61
9.10.16 CR_SECURITY Command............................................................................61
9.10.17 CR_PJLOCKNOW Command.......................................................................61
9.10.18 CR_PJLOCMENU Command........................................................................ 61
9.10.19 CR_FILH Command...................................................................................... 61
9.10.20 CR_FILCOND Command.............................................................................. 62
9.10.21 CR_FILREPL Command............................................................................... 62
9.10.22 CR_FILTIMER Command.............................................................................. 62
9.10.23 CR_FILREMAIN Command .......................................................................... 62
9.10.24 CR_TESTPAT Command .............................................................................. 63
9.11 Other Status Read Commands............................................................................. 64
9.11.1 CR_STATUS Command.................................................................................. 64
PLV-WF20 Expand Serial Command Functional Specifications
7/68
9.11.2 CR_SIGNAL Command...................................................................................64
9.11.3 CR_VMUTE Command....................................................................................64
9.11.4 CR_FREEZE Command..................................................................................64
9.11.5 CR_P-TIMER Command................................................................................. 65
9.11.6 CR_TEMPWARN Command ........................................................................... 65
9.11.7 CR_TEMPFAIL Command...............................................................................66
9.11.8 CR_SERIALNO Command..............................................................................66
9.11.9 CR_SHUTCOND Command............................................................................ 66
10． Command with Address Specification ..................................................................67
10.1. Overview............................................................................................................... 67
10.2. Functional Execution Command with address.................................................. 67
10.3. Status Read Command with Address.................................................................68
PLV-WF20 Expand Serial Command Functional Specifications
8/68
1． Overview
・ This Functional Specification defines communication with Network board for PLV-WF20.
・ Commands are designed to communicate with Network board, but most commands are also
available to remote-control a projector through RS-232C from a computer. Therefore, commands
are defined as Expand Serial Commands.
・ The operation by some commands depends on Optional Board installed in Input Slot of the
projector.
・ This document assumes that Option Boards are installed.
2． Serial Interface Specification
2.1 Transfer Specification
Items Specification
Synchronous System Asynchronous
Transmission Speed 9600 / 19200
Data Length 8 bit
Parity N/A
Stop Bit 1
Flow Control N/A
1) Transmission Speed: initial setting value is 19200
2) Transmission Speed can be changed in Service Mode
2.2 Connection
Dedicated serial cables that come with a projector must be used for the connection between a
computer and the projector.
PC Projector COM 1 Serial Port IN
（D-Sub 9 Pin） （D-Sub 9 Pin）
Connect COM port of the computer to SERIAL PORT IN of the projector.
COM Port (COM1 or COM2) of a computer is specified by control software of the computer.
PLV-WF20 Expand Serial Command Functional Specifications
9/68
3． Notes for communication
・ Expand Serial Command is defined as a single command per line that starts with “C” and ends with
carriage return (0x0D).
・ When a projector receives carriage return (0x0D), it starts decoding.
・ There are two types of commands as below:
Example of Functional Execution Command:”CF_BRIGHT_032” [CR]
Example of Status Read Command: “CR_BRIGHT” [CR]
Note) “_” indicates a space
・ It clears the information of buffer in the following cases:
- when the projector receives LF (0x0A) or EOF (0x1A).
- when it takes more than one second to receive a single command
(Until receiving the carriage return after the reception of the first data)
・ The projector processes the command and returns the response within a few ms to 8000 ms after
the reception of the command. When several commands are sent in succession, do not send
another command unless the response to the previous command has been returned. Need to
confirm that the processing of the current command has been completed and returned the response
before sending another command.
Command
PC → Projector “CF_BRIGHT_032” [CR]
Projector → PC “000” [CR]
Command processing Response
(A few ms – 8000 ms)
Note) when the computer sends another command before the previous response has been
returned, the projector may not operate properly.
Note) when the current command processing has not completed, another command process can
not be accepted by the projector
・ Normally it is less than 1000ms for the completion of receiving a command and returning the
response, but it takes more than 1000ms for some Functional Execution Commands as listed
below:
Command Item
CF_IMAGE Select Image Mode CF_INPUT Select Input CF_SCREEN Select Screen Size CF_SYSTEM Select System CF_INPUT1 Select Input 1 and Signal (concurrent execution) CF_INPUT2 Select Input 2 and Signal CF_INPUT3 Select Input 3 and Signal CF_INPUT4 Select Input 4 and Signal CF_IMAGEADJ Reset/Store for Image Adjustment
・ It takes about 8 seconds for internal initialization after plugging in AC power. During this time it
cannot process commands. Do not issue any command.
PLV-WF20 Expand Serial Command Functional Specifications
10/68
4． Notation
・ Data from a controller to a projector is represented as COMMAND, and data from a projector to a
controller in response to the incoming command is represented as RESPONSE.
・ [CR]: Carriage Return Code
The command ends with carriage return code.
The response also ends with carriage return code.
・ _: Space Code
All space code is indicated by (_).
・ %1: Parameter included in command
When there is more than one parameter, they are represented as %2, %3…
PLV-WF20 Expand Serial Command Functional Specifications
11/68
5． Functional Execution Command Table
5.1 Image Command Table
Execute command Item
CF_CONT_%1[CR]
Set value of Contrast
CF_BRIGHT_%1[CR]
Set value of Brightness
CF_COLOR_%1[CR]
Set value of Color
CF_TINT_%1[CR]
Set value of Tint
CF_COLMNSAV_%1[CR]
Set area to store current values of Color Management
CF_COLMNLD_%1[CR]
Set area to load values of Color Management
CF_APCTRL_%1[CR]
Set level of Auto Picture Control
CF_COLTEMP_%1[CR]
Set level of Color Temperature
CF_WBAL-R_%1[CR]
Set Red value of White Balance
CF_WBAL-G_%1[CR]
Set Green value of White Balance
CF_WBAL-B_%1[CR]
Set Blue value of White Balance
CF_OFFSET-R_%1 [CR]
Set Red value of Offset
CF_OFFSET-G_%1 [CR]
Set Green value of Offset
CF_OFFSET-B_%1 [CR]
Set Blue value of Offset
CF_SHARP_%1[CR]
Set value of Sharpness
CF_GAMMA_%1[CR]
Set value of Gamma
CF_NZRED_%1[CR]
Set ON/OFF of Noise reduction
CF_PROGV_%1[CR]
Set mode of Progressive scan
CF_IMAGE_%1[CR]
Set Image mode
CF_IMAGEADJ_%1[CR]
Set Store/Reset of values in Image Adjustment
5.2 PC Control Command Table
Execute command Item
CF_FSYNC_%1[CR]
Set value of Fine Sync
CF_TDOTS_%1[CR]
Set value of Total Dots
CF_CLAMP_%1[CR]
Set value of Clamp
CF_H-POS_%1[CR]
Set value of Horizontal Position
CF_V-POS_%1[CR]
Set value of Vertical Position
CF_DDOTS_%1[CR]
Set value of Display Dots
CF_DLINE_%1[CR]
Set value of Display Line
CF_SETPCADJ_%1[CR]
Apply values set in PC Adjust menu to screen image
CF_ORGMODE_%1[CR]
Specify the original signal for the selected PC mode
CF_PCSTORE_%1[CR]
Store current setting values in PC Adjust menu to Mode %1
CF_PCMODEFREE_%1 [CR]
Delete the values registered in Mode %1 and return it to Free status.
5.3 Input Control Command Table
Execute command Item
CF_INPUT_%1[CR]
Select Input
CF_SOURCE_%1[CR]
Select Source of selected Input
CF_INPUT1_%1[CR]
Select Input1 and also set input source to %1
CF_INPUT2_%1[CR]
Select Input2 and also set input source to %1
CF_INPUT3_%1[CR]
Select Input3 and also set input source to %1
CF_INPUT4_%1[CR]
Select Input4 and also set input source to %1
PLV-WF20 Expand Serial Command Functional Specifications
12/68
CF_SYSTEM_%1[CR]
Select System in Video input mode
5.4 Screen Command Table
Execute command Item
CF_SCREEN_%1[CR]
Select Screen size
CF_DZCENT _%1[CR]
Cancel Digital Zoom mode
CF_KEYSTONE _%1[CR]
Set Keystone correction
CF_KYSTNMODE _%1 [CR]
Set Keystone store mode
CF_CEIL_%1[CR]
Set ON/OFF of Ceiling
CF_REAR_%1[CR]
Set ON/OFF of Rear
CF_VSCALE_%1[CR]
Set V Scale
CF_VPOS_%1[CR]
Set V Position
CF_HSCALE_%1[CR]
Set H Scale
CF_HPOS_%1[CR]
Set H Position
5.5 Lamp Command Table
Execute command Item
CF_LAMPH_%1[CR]
Reset total running time for each lamp
CF_LAMPMODE_%1[CR]
Select lamp mode (Full/Half)
CF_AUTOLAMPCONTRL_%1[CR]
Switch dimmer function levels of Normal/Auto/Eco
5.6 Setting Command Table
Execute command Item
CF_LANG_%1[CR]
Select language for OSD
CF_DISP_%1[CR]
Set ON/OFF of On Screen Display
CF_BACKGND_%1[CR]
Select screen for no signal
CF_LOGO_%1[CR]
Set ON/OFF of Logo
CF_FANSPEED_%1[CR]
Select Fan Speed
CF_RCODE_%1[CR]
Select Remote Control Code
CF_RSENS_%1[CR]
Select location of infrared remote receiver of remote control
CF_P-MANE_%1[CR]
Set ON/OFF of Power Management
CF_P-MANETIME_%1[CR]
Set time of Power Management
CF_ON-STA_%1[CR]
Set ON/OFF of Power ON Start
CF_PJPINCODE_%1[CR]
Enter PJ PIN code to cancel PJ lock
CF_FILH_%1[CR]
Reset Filter used time
CF_FILTIMER_%1[CR]
Set time to display Filter cleaning / replacement warning on screen
CF_FILCTL_%1[CR]
Execute operation of scroll of filter
CF_FILSCRL_%1[CR]
Reset Filter scroll counter
CF_TESTPAT_%1[CR]
Set Test pattern display function
CF_KEYDIS_%1[CR]
Set limitation of RC/KEY control
CF_FDEFAULT_%1[CR]
Return the settings to Factory Default status
CF_SHUTRCPROT_%1[CR]
Set valid / invalid of RC use on Shutter control function
CF_SHUTKEYPROT_%1[CR]
Set valid / invalid use of key on the top panel on Shutter control function
CF_SHUTH_%1[CR]
Set time of operating shutter management function
PLV-WF20 Expand Serial Command Functional Specifications
13/68
5.7 Other Command Table
Execute command Item
CF_SHUTTER_%1[CR]
Control OPEN / CLOSE of Shutter
6． Status Read Command Table
6.1 Image Status Read Command Table
Status read command Item
CR_CONT [CR]
Get value of Contrast
CR_BRIGHT [CR]
Get value of Brightness
CR_COLOR [CR]
Get value of Color
CR_TINT [CR]
Get value of Tint
CR_APCTRL
Get setting status of Auto Picture Control
CR_COLTEMP
Get value of Color temperature
CR_WBAL-R [CR]
Get Red value of White Balance
CR_WBAL-G [CR]
Get Green value of White Balance
CR_WBAL-B [CR]
Get Blue value of White Balance
CR_OFFSET-R [CR]
Get Offset Red
CR_OFFSET-G [CR]
Get Offset Green
CR_OFFSET-B [CR]
Get Offset Blue
CR_SHARP [CR]
Get value of Sharpness
CR_GAMMA [CR]
Get value of Gamma
CR_NZRED [CR]
Get setting status of Noise reduction
CR_PROGV [CR]
Get setting status of Progressive scan
CR_IMAGE [CR]
Get Selected Image status
CR_IMGGMD [CR]
Get setting value of Image Gamma
6.2 PC Status Read Command Table
Status read command Item
CR_FSYNC [CR]
Get setting value of Fine Sync
CR_TDOTS [CR]
Get setting value of Total Dots
CR_CLAMP [CR]
Get setting value of Clamp
CR_H-POS [CR]
Get setting value of Horizontal Position
CR_V-POS [CR]
Get setting value of Vertical Position
CR_DDOTS [CR]
Get setting value of Display Dots
CR_DLINE [CR]
Get setting value of Display Line
CR_SETPCADJ [CR]
Get currently displayed signal
CR_ORGMODE [CR]
Get the original signal of the mode adjusted in PC Adj.
CR_PCSTORE [CR]
Get Free or Stored status for PC Adj. Mode 1-5
6.3 Video Status Read Command Table
Status read command Item
CR_SERSYS [CR]
Get currently selected signal. In Auto mode, it returns a result by Auto detection.
PLV-WF20 Expand Serial Command Functional Specifications
14/68
6.4 Input Status Read Command Table
Status read command Item
CR_INPUT [CR]
Get selected Input
CR_SOURCE [CR]
Get selected Source
CR_SYSTEM [CR]
Get selected System in Video Input mode
CR_SRCINP1 [CR]
Get selected source for Input 1
CR_SRCINP2 [CR]
Get selected source for Input 2
CR_SRCINP3 [CR]
Get selected source for Input 3
CR_SRCINP4 [CR]
Get selected source for Input 4
CR_HMSLOT [CR]
Get the total number of Slots
CR_NMSLOT1 [CR]
Get a card name inserted to Slot 1
CR_NMSLOT2 [CR]
Get a card name inserted to Slott2
CR_NMSLOT3 [CR]
Get a card name inserted to Slot 3
CR_NMSLOT4 [CR]
Get a card name inserted to Slot 4
CR_IDSLOT1 [CR]
Get ID information of Slot 1
CR_IDSLOT2 [CR]
Get ID information of Slot 2
CR_IDSLOT3 [CR]
Get ID information of Slot 3
CR_IDSLOT4 [CR]
Get ID information of Slot 4
6.5 Screen Status Read Command Table
Status read command Item
CR_SCREEN [CR]
Get selected screen size
CR_KYSTNMODE[CR]
Get selected Keystone store mode
CR_CEIL[CR]
Get selected ON/OFF of Ceiling
CR_REAR[CR]
Get selected ON/OFF of Rear
CR_VSCALE[CR]
Get setting status of V Scale
CR_VPOS[CR]
Get setting status of V Position
CR_HSCALE[CR]
Get setting status of H Scale
CR_HPOS[CR]
Get setting status of H Position
6.6 Lamp Status Read Command Table
Status read command Item
CR_LAMPREPL [CR]
Get information on Lamp replacement time
CR_LAMPMODE [CR]
Get selected Lamp mode
CR_AUTOLAMPCONTROL[CR]
Get setting status of dimmer function level.
CR_LAMPSTS [CR]
Get Lamp lighting status
CR_INFLAMP [CR]
Get Lamp switching status
CR_PROJH [CR]
Get the projector total running time
CR_HMLAMP [CR]
Get the total number of lamps
CR_LAMPH [CR]
Get information of actual Lamp running time
6.7 Setting Status Read Command Table
Status read command Item
CR_LANG [CR]
Get selected language
CR_DISP [CR]
Get setting status of Display
CR_BACKGND [CR]
Get setting status of Screen for no signal
CR_LOGO [CR]
Get setting status of Logo
PLV-WF20 Expand Serial Command Functional Specifications
15/68
CR_LOGOLOCK [CR]
Get setting status of Logo Lock
CR_FANSPEED [CR]
Get selected Fan Control Speed
CR_RCODE [CR]
Get selected Remote Control Code
CR_RSENS [CR]
Get selected location of infrared remote receiver of remote control
CR_P-MANE [CR]
Get setting status of Power management
CR_P-MANETIME [CR]
Get setting time for Power Management
CR_ON-STA [CR]
Get setting status of ON Start
CR_SECURITY [CR]
Get setting status of Security
CR_PJLOCKNOW [CR]
Get setting status of current PJ Lock
CR_PJLOCKMENU [CR]
Get PJ Lock setting status on the menu
CR_FILH[CR]
Get Filter used time
CR_FILCOND[CR]
Get status of filter clog
CR_FILREPL[CR]
Get status of Filter cleaning / replacement time
CR_FILTIMER[CR]
Get time to display Filter cleaning / replacement warning on screen
CR_FILREMAIN[CR]
Get remaining number of usable Filter scroll
CR_TESTPAT[CR]
Get setting status of Test pattern
CR_KEYDIS [CR]
Get setting status of RC/KEY control limitation
CR_SHUTRCPROT[CR]
Get remote controller disability status of the shutter
CR_SHUTKEYPROT[CR]
Get Key controller disability state of the shutter
CR_SHUTH[CR]
Get time setting to begin the shutter management
6.8 Other Status Read Command Table
Status read command Item
CR_STATUS [CR]
Get operation state of the projector
CR_SIGNAL [CR]
Get status of signal existence
CR_VMUTE [CR]
Get setting status of Video mute
CR_FREEZE [CR]
Get setting status of Freeze
CR_PTIMER [CR]
Get operating status of P-Timer
CR_TEMPWARN [CR]
Get temperature status whether it is close to abnormal level or not
CR_TEMPFAIL [CR]
Get temperature in abnormal temperature status
CR_SERIALNO [CR]
Get value of Serial number
CR_SHUTCOND [CR]
Get setting status of Shutter
PLV-WF20 Expand Serial Command Functional Specifications
16/68
7． Error Code Table
Error Code Contents
?
-When the received data cannot be decoded
-Parameter designation error (wrong digit number, including invalid value, etc.)
000 Normal reception (This is “Not” error)
101
Specified function is not available in the selected mode
102 Specified value is out of range (Not reflected)
103
Command mismatched to Hardware (the command is for Optional function which is not implemented)
201
Incremented or decremented value or values are beyond upper or lower limits.
301
Not executable due to screen capturing in process. Prompting reissue of the command after a while.
302
Not executable due to Auto set up in operation. Prompting reissue of the command after a while.
303
Not executable due to memory card viewer in process. Prompting reissue of the command after a while.
402
Not executable due to PIN code in operation. Prompting reissue of the command after a while.
PLV-WF20 Expand Serial Command Functional Specifications
17/68
8． Functional Execution Command
8.1 Format
1) PC issues a command in the format below:
Pattern1: “CF_Command” [CR] Pattern2: “CF_Command_” %1 [CR]
CF_: Header
Command: String
%1: Parameter (String)
_: Space (To separate Command and Parameter)
2) The projector decodes the received command and when it gets ready to receive another
command, it returns the response.
“000” [CR]: (0x06, 0x0D) When receiving Functional Execution Command “nnn” [CR]: Except “000”, when it cannot execute commands for any specific reason.
For detail, refer to [7. Error Code Table]
“?” [CR]: When the received data cannot be decoded
8.2 Transfer Example
When setting projector’s total dots to 1344 by Expand Command.
PC → PJ: “CF_TDOTS_1344” [CR]
PC ← PJ: “000” [CR] ---------------- Acceptable
8.3 Operation Requirements
When the projector status is in the status below, Functional Execution Commands are limited
(Status Read Commands are available in following status)
Projector Status Available Functional Execution Command
In Standby Mode C00: POWER ON
Count Down in process C00: POWER ON (Countdown is terminated)
Cooling Down in process NONE (No Execution)
Cooling Down in process due to abnormal temperature
NONE (No Execution)
In Abnormal Temperature NONE (No Execution)
Power Failure (60 seconds after Power failed)
NONE (No Execution)
Power Saving Cooling Down in process NONE (No Execution)
In Power Saving status
C00: POWER ON C01: POWER OFF
Note) An appropriate error code is returned when the projector receives other command in the
above status.
PLV-WF20 Expand Serial Command Functional Specifications
18/68
8.4 Image Command
8.4.1 CF_ CONT Command
Command “CF_CONT_%1” [CR]
%1
“000-063”--------------- Directly specify setting value of Contrast “UP”--------------------- Increment setting value of Contrast by 1 “DN”--------------------- Decrement setting value of Contrast by 1
Details
Set user controlled value of Contrast. (Available only in the normal Power ON status) The value set by this command is not stored in the projector. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.2 CF_ BRIGHT Command
Command “CF_BRIGHT_%1” [CR]
%1
“000-063” --------------- Directly specify setting value of Brightness “UP” ---------------------- Increment setting value of Brightness by 1 “DN” ---------------------- Decrement setting value of Brightness by 1
Details
Set user controlled value of Brightness. (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.3 CF_COLOR Command
Command “CF_COLOR_%1” [CR]
%1
“000-063”--------------- Directly specify setting value of Color “UP”--------------------- Increment setting value of Color by 1 “DN”--------------------- Decrement setting value of Color by 1
Details
Set user controlled value of Color. (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.4 CF_TINT Command
Command “CF_TINT_%1” [CR]
%1
“000-063”--------------- Directly specify setting value of Tint “UP”--------------------- Increment setting value of Tint by 1 “DN”--------------------- Decrement setting value of Tint by 1
Details
Set user controlled value of Tint (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
PLV-WF20 Expand Serial Command Functional Specifications
19/68
8.4.5 CF_COLMNAV Command
Command “CF_COLMNSAV_%1” [CR]
%1 “000 – 009” ---------------- Specify the area to store
Details
Store current setting status of Color Management to the area specified in %1. (Available only in the normal Power ON status)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.6 CF_COLMNLD Command
Command “CF_COLMNLD_%1” [CR]
%1 “000 – 009” ---------------- Specify the area to store
Details
Retrieve Color Management setting status from the area specified in %1. (Available only in the normal Power ON status)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.7 CF_APCTRL Command
Command “CF_APCTRL_%1” [CR]
%1
“L1” ------------------- Set Auto Picture Control to Level 1. “L2” ------------------- Set Auto Picture Control to Level 2. “OFF” ---------------- Set Auto Picture Control OFF. “ UP” ------------------ Switch setting forward direction (OFF→L1→L2→OFF) “ DN” ------------------ Switch setting backward direction (OFF→L2→L1→OFF)
Details
Set Auto Picture Control (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.8 CF_COLTEMP Command
Command “CF_COLTEMP_%1” [CR]
%1 “000” – “003”
Details
Set Color Temperature (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
PLV-WF20 Expand Serial Command Functional Specifications
20/68
8.4.9 CF_WBAL- Command
Command “CF_WBAL-%1_%2” [CR]
%1
“R” ------------- RED “G” ------------ GREEN “B” ------------- BLUE
%2
“000-063”------ Directly specify value of Color selected in %1 of White Balance. “UP”------------ Increment setting value of Color specified in %1 of White Balance by 1 “DN”------------ Decrement setting value of Color specified in %1 of White Balance by 1
Details
Set value of Color specified in %1 of White Balance (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.10 CF_OFFSET- Command
Command “CF_OFFSET-%1_%2” [CR]
%1
“R” --------- RED “G” --------- GREEN “B” --------- BLUE
%2
“000-063”------ Directly specify value of Color selected in %1 of Offset. “UP”------------ Increment setting value of Color specified in %1 of Offset by 1 “DN”------------ Decrement setting value of Color specified in %1 of Offset by 1
Details
Set value of Color specified in %1 of Offset (Available only in the normal Power ON status) The value set by this command will not be stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code”[CR]
8.4.11 CF_SHARP Command
Command “CF_SHARP_%1” [CR]
%1
“000-031” -------------- Directly specify setting value of Sharpness. “UP”--------------------- Increment setting value of Sharpness by 1 “DN”--------------------- Decrement setting value of Sharpness by 1
Details
Set user controlled value of Sharpness. (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
PLV-WF20 Expand Serial Command Functional Specifications
21/68
8.4.12 CF_GAMMA Command
Command “CF_GAMMA_%1” [CR]
%1
“000-015” ---------------- Directly specify setting value of Gamma “UP”---------------------- Increment setting value of Gamma by 1 “DN”---------------------- Decrement setting value of Gamma by 1
Details
Set user controlled value of Gamma. (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.13 CF_NZRED Command
Command “CF_NZRED_%1” [CR]
%1
“ON” ------------------------------Set Noise Reduction to ON “OFF” ---------------------------- Set Noise Reduction to OFF
Details
Set or Cancel Noise Reduction. (Available only in the normal Power ON status) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.14 CF_PROGV Command
Command “CF_PROGV_%1” [CR]
%1
“ON” ------------------------------ Set Progressive scan to ON “FILM” ---------------------------- Set Progressive scan to Film mode “OFF” ---------------------------- Set Progressive scan to OFF
Details
Set or Cancel Progressive scan. (Valid only when it is in the normal Power ON status.) The value set by this command is not stored in the projector’s memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
Loading...
+ 47 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use