Sanyo PLV-HD150 User Manual

Owner's Manual
PLV-HD150
Multimedia Projector
MODEL
Projection lens is optional.
2
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.
TO THE OWNER
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.
This projector should be set in the way indicated. If not, it may result in a fire hazard.
Take appropriate space on the top, sides and rear of the projector
cabinet for allowing air circulation and cooling the projector. Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.
Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.
If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
SIDE and TOP
REAR
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.
Ne puet être utillisé dans une salle dordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for Protection of Electronic Computer/Data Processing Equipment
20cm
50cm 50cm
1m
3
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
Voor de klanten in Nederland
Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
4
COMPLIANCES
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
AC POWER CORD REQUIREMENT
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.
CAUTION!
This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator can be asked to take adequate countermeasures.
GROUND
5
TABLE OF CONTENTS
TRADEMARKS
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
Windows and PowerPoint are registered trademarks of Microsoft Corporation.
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
FEATURES AND DESIGN 6
BEFORE OPERATION 16
DISPLAY ADJUST 28
SETTING 37
APPENDIX 41
PREPARATION 7
NAME OF EACH PART OF PROJECTOR 7 SETTING-UP PROJECTOR 8
CONNECTING AC POWER CORD 8 LENS INSTALLATION 9 POSITIONING PROJECTOR 9 LENS SHIFT ADJUSTMENT 9 PICTURE LEVEL AND TILT ADJUSTMENT 10 MOVING PROJECTOR 10
CONNECTING PROJECTOR 11
TERMINALS OF PROJECTOR 11 CONNECTING TO COMPUTER 14 CONNECTING TO VIDEO EQUIPMENT 15
SIDE CONTROLS AND INDICATORS 16 OPERATION OF REMOTE CONTROL 18
REMOTE CONTROL CODE CHANGE AND OPERATING RANGE 19 REMOTE CONTROL BATTERIES INSTALLATION 19
OPERATING ON-SCREEN MENU 20
HOW TO OPERATE ON-SCREEN MENU 20 FLOW OF ON-SCREEN MENU OPERATION 20 MENU BAR 21
DISPLAY ADJUSTMENTS 28
SCREEN ADJUSTMENTS 28 AUTO PC ADJUSTMENT 29 MANUAL DISPLAY ADJUSTMENTS 30
IMAGE ADJUSTMENTS 32
IMAGE LEVEL SELECT 32 IMAGE LEVEL ADJUSTMENTS 33
SETTING MENU 37
MAINTENANCE 41
WARNING TEMP. INDICATOR 41 AIR FILTER CARE AND CLEANING 41 LAMP MANAGEMENT 42 LAMP REPLACEMENT 43 CLEANING PROJECTION LENS 44
TROUBLESHOOTING 45
INDICATORS AND PROJECTOR CONDITION 47 MENU TREE 48
TECHNICAL SPECIFICATIONS 50
CONFIGURATIONS OF TERMINALS 51 COMPATIBLE COMPUTER SPECIFICATIONS 52 OPTIONAL PARTS 53
BASIC OPERATION 22
TURNING ON / OFF PROJECTOR 22 ADJUSTING SCREEN 23
ZOOM ADJUSTMENT 23 FOCUS ADJUSTMENT 23 LENS SHIFT ADJUSTMENT 23 PICTURE FREEZE FUNCTION 23 NO SHOW FUNCTION 23
SOUND ADJUSTMENT 24 SELECTING INPUT SOURCE 25 SYSTEM SELECT 26
AUTOMATIC MULTI-SCAN SYSTEM 26 SELECT COMPUTER SYSTEM MANUALLY 26 SELECT VIDEO SYSTEM 27
6
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
Compatibility
This projector widely accepts various video and computer input signals including;
Computers
IBM-compatible or Macintosh computer up to 1600 x 1200 resolution.
6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL­N color system can be connected.
Component Video
Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i­60, can be connected.
S-Video
S-Video signal, such as a S-VHS VCR output signal, can be connected.
High Resolution Image
This projector provides 1920 x 1080 dots resolution for computer input and 1100 horizontal TV lines. This projector cannot display image of over 1600 x 1200 dots. When resolution of your computer is over than 1600 x 1200, reset a computer output for lower resolution.
Multi-Scan System
This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.
Multilanguage Menu Display
Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean or Japanese.
One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.
Power Management
Power Management function is provided to reduce power consumption while a projector is not in use. This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed. This projector is shipped with this function ON.
Digital Visual Interface
This projector is equipped with DVI 29-pin terminal for connecting DVI output from a computer.
Progressive Scan Function
This function converts interlace video signals into progressive scan signals and provide fine picture quality.
Motor-driven Lens Shift
Projection lens can be moved up, down left and right with motor-driven lens shift function. This function makes it easy to provide projected image where you want. Zoom and focus can be also adjusted with motor-driven operation.
Multi Versatile Platform
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment.
4-built-in Terminal Slots enable you to arrange any combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.
Selectable Terminal Slots
Network board (Optional)
Network board is an optional product to control and set up a projector via the network cable. By accessing to the connected projector using the web browser on your computer. It can be controlled and set up the projector remotely. Contact the sales dealer where you purchased this projector for optional parts.
7
PREPARATION
NAME OF EACH PART OF PROJECTOR
BOTTOM OF CABINET
BACK OF CABINET
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When using or installing a projector, following precautions should be taken.
Do not put a flammable object near this vent.
Keep rear grills at least 3.3 (1m) away from
any object, especially heat-sensitive object.
Do not touch this area, especially screws and metallic parts. This area will become hot while a projector is used.
This projector detects internal temperature and automatically controls operating power of Cooling Fans.
FRONT OF CABINET
LAMP COVER
ADJUSTABLE FEET
This projector is equipped with cooling fans for protection from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.
Do not cover vent slots.
Keep bottom clear of any objects.
Obstructions may block cooling air.
AIR INTAKE VENTS
PROJECTION LENS
SPEAKERS
INFRARED
REMOTE RECEIVER
LENS COVER
POWER CORD
CONNECTOR
EXHAUST VENT
MAIN ON / OFF
SWITCH
INFRARED
REMOTE RECEIVER
CARRYING HANDLE
LEVEL AND TILT ADJUST HANDLE
AIR FILTER
ADJUSTABLE FEET
Do not turn on a projector with lens cover attached. High temperature from light beam may damage lens cover and result in fire hazard.
CAUTION
8
PREPARATION
SETTING-UP PROJECTOR
This projector uses nominal input voltages of 240 V AC. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of type of power supply being in use. Connect a projector with peripheral equipment before turning a projector on. (Refer to pages 12 ~ 15 for connection.)
CONNECTING AC POWER CORD
To the AC Outlet
(240 V AC)
9
PREPARATION
POSITIONING PROJECTOR
Before setting up a projector, install Projection Lens on a Projector.
1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a projector.
2. For installation, refer to installation manual supplied to a Projector.
LENS INSTALLATION
When moving or setting up a projector, be sure to replace a Lens Cover to protect a surface. And be careful not to hold or subject a lens to strong forces. It may damage lens, cabinet, or mechanical parts.
Projection lens can be moved up, down, left and right with motor-driven lens shift function. This function makes it easy to provide projected image where you want.
LENS SHIFT ADJUSTMENT
MOVED UP OR DOWN
MOVED LEFT OR RIGHT
Use LENS SHIFT button and POINT UP/DOWN button to move image up or down. (Refer to page 23.)
Use LENS SHIFT button and POINT LEFT/RIGHT button to move image left or right. (Refer to page 23.)
This projector is designed to project on a flat projection surface.
ROOM LIGHT
Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.
This projector is equipped with cooling fan to protect it from over­heating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.
Do not cover vents with papers or other materials.
Keep rear grill at least 3.3 feet (1 m) away from any
object.
Make sure that there are no objects under a projector. An object under a projector may prevent a projector from taking cooling air through bottom vent.
VENTILATION
AIR INTAKE VENT (BOTTOM SIDE)
EXHAUST VENT (REAR SIDE)
SCREEN
10
PREPARATION
PICTURE LEVEL AND TILT ADJUSTMENT
Picture tilt and projection angle can be adjusted with handles on both sides of a projector. Projection angle can be adjusted to 5.7 degrees upper way.
1
2
3
MOVING PROJECTOR
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
Do not drop or bump a projector, otherwise damages or malfunctions may result.
When carrying a projector, use a suitable carrying case.
Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer and best case should be applied.
For safety, be sure to hold Carrying Handles on both sides by 2 or more people when moving a projector. Moving it unproperly may result in damage of cabinet or person's injury. Replace lens cover and retract feet to pre­vent damage to lens and cabinet.
1
2
3
Pull up lock buttons on each side of carrying handles and release locks.
CARRYING HANDLE
LOCK BUTTONS
Pull carrying handles out fully until it's locked (with a click). Move a projector by holding two handles by 2 or more people.
To retract carrying handles, pull up lock buttons and release lock of handles and press handles fully in until it's locked.
LEVEL AND TILT ADJUST HANDLE
ADJUSTABLE FEET
Height of front feet can be adjusted by turning handles.
KNOB
Press knob on handle. Handle pop out.
Turn handles (right and left) until picture is projected on proper position. Adjust height of rear adjustable feet by rotating them until projector properly stabled on table.
Press knob and retract handle.
REAR ADJUSTABLE FEET. (Refer to P7).
Pull up lock buttons to release lock.
11
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.
Pull out terminal by holding handle.
Remove 2 Screws on terminal.
1
2
REPLACEMENT OF TERMINAL
Tighten screws to secure terminal.
Replace terminal. Insert terminal along Guide to fit Plug into Socket.
3
4
INPUT 1INPUT 2INPUT 3
DVI
AUDIO
CONTROL PORT
CONTROL PORT
AUDIO
R/Pr G/Y B/Pb H/HV V
(MONO)
(MONO)
R L
R L
(MONO)
AUDIO OUT
R L
R/C JACK USB
SERIAL PORT IN
SERIAL PORT OUT
RESET
INPUT 4
SDI IN1 SDI IN2 SDI OUT
INPUT/OUTPUT TERMINALS
Screws
Guide
Socket
Plug
Figure shows DVI terminal.
SDI Terminal
5 BNC Terminal
DVI Terminal
3 TERMINAL SLOTS (Factory set)
NOTES ON ORDERING OR USING OPTIONAL INTERFACE BOARD
When ordering or using Optional Interface Board (Terminal Board), contact your sales dealer. When con­tacting the sales dealer, tell the Optional Control Number (Op.cont.No.) in the menu that is located under Language Select Menu. (See page 37.)
NOTE; When replacement of terminal board, MAIN
ON/OFF switch should be OFF position.
12
CONNECTING PROJECTOR
Connect audio output from computer or video equipment to these jacks. (Refer to P14, 15.)
CONTROL PORT CONNECTORS
AUDIO INPUT JACKS
5 BNC INPUT JACKS
Connect component video output (Cr, Y, Cb or Pr, Y, Pb) from video equipment to R/Pr, G/Y and B/Pb jacks or connect computer output [5 BNC Type (Red, Green, Blue, Horiz. Sync and Vert. Sync.)] from computer to R/Pr, G/Y, B/Pb, H/HV and V jacks. (Refer to P14,
15)
Connect computer output (Digital/Analog DVI-I type) to this terminal. Connect digital video output from video equipment to this terminal. (Refer to P14, 15.)
DVI INPUT TERMINAL
INPUT/OUTPUT TERMINALS AND JACKS
INPUT 2
INPUT 3
INPUT 2, 3
INPUT 2, 3,
INPUT 1
Connect SDI output from video equipment to these jacks. (Refer to P15.)
SDI INPUT JACKS
INPUT 1
Connect SDI input from video equipment to this jack. (Refer to P15.)
SDI OUTPUT JACK
The port is not functioning in this model.
SERIAL PORT IN
SERIAL PORT OUT
R/C JACK USB
AUDIO OUT
R L
RESET
SDI IN1 SDI IN2 SDI OUT
R/Pr G/Y B/Pb H/HV V
DVI
AUDIO
R L
AUDIO
R L
INPUT 1INPUT 2INPUT 3
CONTROL PORT
(MONO)
CONTROL PORT
(MONO)
(MONO)
INPUT 4
13
CONNECTING PROJECTOR
Connect an external audio amplifier to these jacks. (Refer to P14, 15.)
AUDIO OUTPUT JACKS
This projector uses a micro processor to control unit. Occasionally, micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart unit. Do not use RESET function excessively.
RESET BUTTON
When using Wired / Wireless Remote Control Unit as Wired Remote Control, Connect Wired Remote Control Unit to this jack with Remote Control Cable (supplied). (Refer to page 18.)
R/C JACK
USB PORT (Series B)
SERIAL PORT
OUT TERMINAL
SERIAL PORT
IN TERMINAL
This port is used to control a projector with computer. Connect USB port of computer to this port.
If you control a projector by computer, you must connect a cable (not provided) from your computer to this terminal.
This terminal outputs signal from SERIAL PORT IN. More than two projectors can be controlled with one computer by connecting SERIAL PORT IN. of another projector to this terminal.
R/C JACK USB
SERIAL PORT IN
SERIAL PORT OUT
AUDIO OUT
R L
RESET
SDI IN1 SDI IN2 SDI OUT
R/Pr G/Y B/Pb H/HV V
DVI
AUDIO
R L
AUDIO
R L
INPUT 1INPUT 2INPUT 3
CONTROL PORT
(MONO)
CONTROL PORT
(MONO)
(MONO)
INPUT 4
14
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA/UXGA)
DVI-VGA Cable
Monitor Output
Desktop type
Laptop type
Audio Cable
(stereo)
Audio Output
Audio Input
AUDIO OUT
MAC/VGA Adapter
Set slide switches following chart below.
Cables used for connection (= Cables are not supplied with this projector.)
DVI Cable
DVI-VGA Cable (HDB 15 pin)
MAC/VGA Adapter
BNC Cable (BNC x 5)
Audio Cables (RCA x 2)
Audio Cable
(stereo)
NOTE :
When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. Turn a projector and peripheral equipment on before computer is switched on.
Terminals of
a Projector
Audio Amplifier
Audio Speaker
(stereo)
External Audio Equipment
Monitor Output
DVI Cable
BNC Cable
Set switches as shown in table below depending on RESOLUTION MODE that you want to use before your turn on a projector and computer
13"MODE (640 x 480)
16"MODE (832 x 624)
19"MODE (1024 x768)
21"MODE (1152 x 870)
ON
OFF
OFF OFF OFF OFF
OFF OFFOFF
OFF OFF OFF
ON
ON
ON ON ON
OFF
OFF OFF
ON ON
ON
ON
1 2 3 4 5 6
MODE
SWITCHES
Switches of MAC/VGA Adapter
MAC/VGA ADAPTER
Monitor Output
SERIAL PORT IN
SERIAL PORT OUT
R/C JACK USB
AUDIO OUT
R L
RESET
(MONO)
SDI IN2
SDI IN1
R/Pr G/Y B/Pb H/HV V
SDI OUT
DVI
R L
R L
AUDIO
(MONO)
AUDIO
(MONO)
CONTROL PORT
CONTROL PORT
INPUT 1INPUT 2INPUT 3
INPUT 4
ON
ON
1
DIP
2 3 4 5 6
OFF
15
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Video Source (example)
Audio Amplifier
Audio Speaker (stereo)
Audio Cable
(Stereo)
Audio Input
Cables used for connection
Video Cable (BNC)
Audio Cable (RCA x 2)
Scart Cable
DVI-VGA Adapter
(= Cables are not supplied with this projector.)
NOTE :
When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. Turn a projector and peripheral equipment on before computer is switched on.
Audio Output
Y
Pb/Cb
Pr/Cr
RL
External Audio Equipment
AV AUDIO IN
Pr/Cr-Y-Pb/Cb
AUDIO OUT
Component video output equipment.
(such as DVD player or
high-definition TV source.)
Component Video Output
Audio Cable
(Stereo)
Terminals of
a Projector
RGB Scart
21-pin Output
Scart Cable
DVI-VGA Adapter
SDI IN 1/SDI IN 2
Video Equipment with
SDI signal output/input
DVI
SDI Output SDI Input
SDI OUTPUT
Video Equipment with
Digital video signal output
DVI
Digital Video Output
BNC Cable
BNC Cable
SERIAL PORT IN
SERIAL PORT OUT
R/C JACK USB
AUDIO OUT
R L
(MONO)
RESET
SDI IN2
SDI IN1
R/Pr G/Y B/Pb H/HV V
SDI OUT
DVI
AUDIO
R L
AUDIO
R L
(MONO)
INPUT 1INPUT 2INPUT 3
CONTROL PORT
(MONO)
CONTROL PORT
INPUT 4
16
IMAGE button
Selects image levels. (P32)
BEFORE OPERATION
MENU
AUTO PC ADJUST
IMAGE
SELECT
VOLUME
ZOOM FOCUS
LENS SHIFT
ON-OFF
INPUT 1/2
INPUT 3/4
SIDE CONTROLS AND INDICATORS
Adjust zoom. (P23)
INPUT 3/4 button
POWER ON–OFF button
FOCUS buttons
VOLUME buttons
Select input source either INPUT 3 or INPUT 4. (P25)
Adjust focus. (P23)
Adjust volume. (P24)
Selects an item or adjusts value in the On-Screen Menu. (P20)
Executes the item selected. (P20)
Turns the projector on or off. (P22)
ZOOM buttons
Select LENS SHIFT function. (P23)
SELECT button
POINT buttons
LENS SHIFT button
SIDE CONTROLS
MENU button
Open or close the On-Screen Menu operation. (P20, 21)
INPUT 1/2 button
Select input source either INPUT 1 or INPUT 2. (P25)
SIDE CONTROLS
REAR INDICATORS
FRONT INDICATORS
AUTO PC ADJ. button
Operates the AUTO PC adjustment function. (P29)
17
BEFORE OPERATION
READY
LAMP
LAMP
REPLACE
WARNING
TEMP.
READY indicator
LAMP indicator
LAMP REPLACE indicator
This indicator lights green when a projector is ready to be turned on. And it flashes green in Power Management mode or internal projector temperature is to high. (P39, 41)
This indicator is dim when a projector is turned on. And bright when a projector is in stand-by mode.
INDICATORS
WARNING TEMP. indicator
This indicator flashes red when internal projector temperature is too high. (P41)
WARNING
TEMP.
READY
LAMP
REPLACE
LAMP
FRONT INDICATORS
REAR INDICATORS
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them becomes out. Check which lamp needs to be replaced on Lamp Status Display.
(P42-43)
18
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
q
w
y
u
!0
e r
t
o
i
!2
!3 !4
!6
!7
!8
!5
!9
!1
!9 RESET switch
Slide this switch to the "RESET" to initialize the remote control code.
(P19, 39)
w SIGNAL EMISSION indicator
This indicator lights red while a signal is being sent from the remote control to the projector.
e SCREEN button
Select image screen. (P28)
r ZOOM button
Adjust zoom. (P23)
!7
INPUT 1-4 buttons
Select input source (INPUT 1-INPUT 4). (P25)
i POINT (UP/DOWN/LEFT/RIGHT) button
Selects an item or adjusts value in the On-Screen Menu. (P20) Point Left/Right button are also used as VOLUME +/- button. (P24)
!0 IMAGE (1-10) buttons
Selects image levels (IMAGE 1 - IMAGE 10). (P32)
!3 AUTO PC button
Operates the Auto PC adjustment function. (P29)
!4 NO SHOW button
Turns the picture into black image. (P23)
!5 MENU button
Opens or closes the On-Screen Menu. (P20)
t FREEZE button
Freezes the projected picture. (P23)
y
MUTE button
Mutes sound. (P24)
!2 POWER ON-OFF button
Turns the projector on or off. (P22)
!6
LENS SHIFT button
Select LENS SHIFT function. (P23)
u FOCUS button
Adjust focus. (P23)
!8 IMAGE button
Selects image levels. (P32)
q SELECT button
Executes the item selected. (P20)
!1 WIRED REMOTE JACK
When using as Wired Remote Control, connect Remote Control Cable to this jack. Battery installation is required when using as Wired Remote Control.
o SELECT button
Executes the item selected. (P20)
ZOOM
FOCUS
ON-OFF
RESET
SELECT
Remote Control Code
Number of Times of
Pressing IMAGE
Button
19
BEFORE OPERATION
To insure safe operation, please observe following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at same time.
Do not use a new battery with an used battery.
Avoid contact with water or liquid.
Do not expose Remote Control Unit to moisture, or heat.
Do not drop Remote Control Unit.
If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
Danger of explosion if battery is incorrectly replaced.
Dispose of used batteries according to the batteries manufacturers instructions and local rules.
Press lid down­ward and slide it.
Remove battery compartment lid.
Slide batteries into compartment.
Replace compartment lid.
Two AA size batteries
For correct polarity (+ and –), be sure battery terminals are in contact with pins in compartment.
Remote Control Batteries Installation
1 2 3
Operating Range
Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about 16.4 (5m) and 60° in front and rear of a projector.
16.4 (5 m)
60°
16.4 (5 m)
60°
Code Change
This projector has eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. (Change the remote control code for the projector first before changing that for the remote control. See Remote control on page 39.)
While pressing the MENU button, press the IMAGE button number of times corresponding to each remote control code number. Each time you press the IMAGE button, the code is changed sequentially. (See the list below.)
1
To initialize the remote control code for the remote control, slide the RESET switch to the RESET, and then to the ON. The initial code is Code 1.
2
RESET
Code 1 1
Code 2 2
Code 3 3
Code 4 4
Code 5 5
Code 6 6
Code 7 7
Code 8 8
MENU button
IMAGE button
Remote Control Code Change and Operating Range
ZOOM
FOCUS
RESET
ON-OFF
SELECT
20
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU BAR). A red frame is POINTER.
Move POINTER (red frame) to MENU ICON that you want to select by pressing POINT RIGHT / LEFT buttons.
Adjust ITEM DATA by pressing POINT RIGHT / LEFT buttons. Refer to following pages for details of respective adjustments.
Press POINT UP/DOWN button and move POINTER (red frame or red arrow) to ITEM that you want to adjust, and then press SELECT button to show ITEM DATA.
Select Menu to be adjusted
Control or adjust item through ON-SCREEN MENU
1
2
4
3
You can control and adjust this projector through ON-SCREEN MENU. Refer to following pages to operate each adjustment on ON-SCREEN MENU.
2 MOVING POINTER
3 SELECT ITEM
Move pointer (see below) or adjust value of item by pressing POINT button(s) on Side Control or on Remote Control Unit.
Select item or set selected function by pressing SELECT button.
OPERATING ON-SCREEN MENU
Pointer is a icon on ON-SCREEN MENU to select item. See fig-
ures on section "FLOW OF ON-SCREEN MENU OPERATION" below.
I
Used to select item.
SELECT BUTTON
Used to move Pointer UP/ DOWN/ RIGHT/ LEFT.
POINT BUTTONS
SIDE CONTROL
MENU BAR
MENU ICON
SELECT
BUTTON
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
FOCUS
ZOOM
ON-OFF
Used to select item.
SELECT BUTTON
Used to move Pointer UP/ DOWN/ RIGHT/ LEFT.
POINT BUTTON
WIRELESS REMOTE CONTROL
ITEM DATA Press POINT LEFT/RIGHT buttons to adjust value or set function.
POINTER (red frame) Press POINT DOWN button to move POINTER.
POINTER (red frame)
ITEM
MENU BUTTON
MENU BUTTON
SELECT
MENU
SELECT
UTO PC ADJUST
LENS SHIFT
IMAGE
I
21
BEFORE OPERATION
MENU BAR
SETTING MENU
Used to change settings of projector or reset Lamp Replace Counter. (Refer to P37-40)
GUIDE WINDOW
Shows selected item of ON­SCREEN MENU.
SYSTEM BOX
Used to select computer system or video system. Shows selected system on this box. (Refer to P26-27)
INPUT MENU
Used to select input source (Input 1, Input 2, Input 3 or Input 4). Refer to P25.
SOUND MENU
Used to adjust sound [
volume, Bass or Treble
], to select Built-in SP On­Off and Sound Mute. (Refer to P24)
IMAGE ADJUST MENU
Used to select image level among Standard (AV), Cinema, Standard (PC), Real and Image 1 ~ 10. (Refer to P32) Used to adjust image. [Contrast/Brightness/Color/Tint/Color Temp. /White Balance (R/G/B)/Sharpness/Detail Enhancer /Gamma/Noise Reduction/Progressive/Auto picture control/Auto Lamp Control/Color management/Gamma balance] (Refer to P33-36)
DISPLAY ADJUST MENU
Used to adjust size of image. {Full/Normal/Anamorphic} (Refer to P28)
Used to adjust parameters to match with input signal format. (Refer to P30-31)
22
BASIC OPERATION
TURNING ON PROJECTOR
TURNING OFF PROJECTOR
TURNING ON / OFF PROJECTOR
Connect a projector's AC Power Cord into a wall outlet and turn MAIN ON/OFF SWITCH to ON. LAMP indicator lights RED, and READY indicator lights GREEN.
Press POWER ON-OFF button on Side Control or on Remote Control Unit to ON. LAMP indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and count­down starts. Signal from source appears after 30 seconds. Current Input and Lamp status are also displayed on screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on page 42.)
2
3
Press POWER ON-OFF button on Side Control or on Remote Control Unit, and a message "Power off?" appears on a screen.
1
2
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.
1
Complete peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO PROJECTOR" on Pages 12~15 for connecting that equipment.)
3
30
Preparation Display disappears after 30 seconds.
Press POWER ON-OFF button again to turn off projector. LAMP indicator lights bright and READY indicator turns off. After approximate 90 seconds, READY indicator will light green again and projector may be turned on by pressing POWER ON-OFF button.
Cooling fans will operate for approximate 2 minutes after projec­tor is turned off. To power down completely, turn MAIN ON/OFF SWITCH to OFF and disconnect AC Power Cord.
INPUT AND LAMP STATUS
Message disappears after 4 seconds.
When WARNING TEMP. Indicator is flashing, projector cannot be turned on, refer to the section "MAINTENANCE" on page 41. When the both WARNING TEMP. and READY Indicator flashing, refer to the section "MAINTENANCE" on page 41.
When Power Management function mode is Ready or Shut down, projector detects signal interruption and turns off the Projection Lamp automatically. Refer to Power management on page 39.
Do not use the projector continuously for 24 hours or more. If using the projector continuously for long periods, turn it off and leave it for one hour at least once during a 24 hour period. If you use the projector continuously for long period, it can excessively shorten the life of the lamp.
23
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
1
Press ZOOM ▲/▼ button on Side Control or on Remote Control Unit. Message Zoom is displayed.
2
Press ZOOM button to make image larger, and press ZOOMbutton to make image smaller.
1
Press FOCUS ▲/▼ button on Side Control or on Remote Control Unit. Message Focus is displayed.
2
Adjust focus of image by pressing FOCUS ▲/▼ button(s) .
LENS SHIFT ADJUSTMENT
Message disappears after 4 seconds.
1
Press the LENS SHIFT button on Side Control or on the Remote Control Unit. Message Lens shift is displayed.
2
Press POINT UP button to move image up, press POINT DOWN button to move image down, press POINT LEFT to move image left and press POINT RIGHT to move image right.
Message disappears after 4 seconds.
Message disappears after 4 seconds.
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button.
Press NO SHOW button on Remote Control Unit to black out image. To restore to normal, press NO SHOW button again or press any other button.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
Message disappears after 4 seconds.
24
BASIC OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SOUND Menu icon.
Volume
Press VOLUME (+/–) button(s) on Side Control or on Remote Control Unit to adjust volume. Volume dialog box appears on screen for a few seconds. (+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press Volume (+/–) button(s).
To increase volume, press POINT RIGHT button, and press POINT LEFT button for decreasing.
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box display is changed to On and sound is cut off. To restore sound to its previous level, press POINT LEFT/RIGHT button(s) again.
Press POINT DOWN button to move a red frame pointer to item that you want to select, and then press SELECT button.
SOUND ADJUSTMENT
DIRECT OPERATION
MENU OPERATION
Volume
Mute
Treble
To adjust Treble sound, press POINT RIGHT button or POINT LEFT button.
Bass
To adjust Bass sound, press POINT RIGHT button or POINT LEFT button.
Built-in SP.
Closes SOUND MENU.
Quit
Press POINT LEFT/RIGHT button(s) to switch built-in speaker on and off.
Close SOUND Menu.
Indicates roughly level of volume.
Press MUTE button to set Mute function On or Off.
Display disappears after 4 seconds.
SOUND MENU
SOUND Menu icon
Indicates roughly level of volume.
25
BASIC OPERATION
When connect component video output (Cr, Y, Cb or Pr, Y, Pb) from video equipment to R/Pr, G/Y and B/Pb jacks.
WHEN SELECT INPUT 2 (5 BNC TERMINAL)
WHEN SELECT INPUT 1 (SDI TERMINAL )
Input 1
INPUT MENU
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Select INPUT source by pressing INPUT 1/2 and INPUT 3/4 buttons on Side Control or INPUT 1, INPUT 2, INPUT 3 and INPUT 4 on Remote Control Unit.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select Input and press SELECT button.
Another dialog box INPUT SELECT
Menu will appear.
Press POINT DOWN button and a red-arrow icon will appear. Move arrow to INPUT source that you want to select, and then press SELECT button.
1
2
INPUT 1/2 button
INPUT 1
INPUT 2
Input 2
INPUT 3/4 button
INPUT 3
INPUT 4
INPUT 1-4 buttons
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT Menu icon
Move arrow to INPUT source that you want to select, and then press SELECT button.
WHEN SELECT INPUT 3 (DVI TERMINAL)
Input 3
When your computer is connected to INPUT 3 (DIGITAL) terminal, select RGB(PC Digital).
RGB(AV HDCP)
When your computer is connected to INPUT 3 (ANALOG) terminal, select RGB(Analog).
RGB(Analog)
RGB(PC Digital)
RGB(Scart)
When video equipment is connected to INPUT 3 (ANALOG) terminal, select RGB(Scart).
If a HDCP-compatible signal source is connected to the INPUT 3 (DIGITAL) terminal, select RGB(AV HDCP).
NOTE; HDCP (High-bandwidth Digital Content Protection) is a system for protecting digital entertainment content which is delivered by DVI (Digital Visual Interface) from being copied. The specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP.
Move a pointer to either SDI 1 or SDI 2 and press SELECT button.
RGB
Y, Pb/Cb, Pr/Cr
Move a pointer to source that you want to select and press SELECT button.
Move a pointer to source that you want to select and press SELECT button.
When connect a computer output [5 BNC Type (Red, Green, Blue, Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV and V jacks.
26
BASIC OPERATION
SYSTEM SELECT
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA or UXGA (refer to COMPATIBLE COMPUTER SPECIFICATION on pages 52-53). When a computer is selected, this projector automatically tunes to incoming signal and projects the proper image without any special setting. (Some computers need to be set manually.)
The projector displays one of the Auto, -----, Mode 1 ~ Mode 20, or the system provided in the projector.
When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and message Auto is displayed on SYSTEM Menu icon. When image is not provided properly, manual adjustment is required. (Refer to P30 and 31.)
There is no signal input from computer. Make sure connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 45.)
Auto
––––
SYSTEM SELECT Menu icon Displays system being selected.
SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SYSTEM SELECT Menu icon.
Press POINT UP/DOWN button to move a red arrow pointer to system that you want to set, and then press
SELECT button.
1
2
SYSTEM SELECT MENU (PC)
This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually.
AUTOMATIC MULTI-SCAN SYSTEM
SYSTEM SELECT Menu icon Displays system being selected.
Systems on this dialog box can be selected.
Custom Mode (1 ~ 20) set in DISPLAY ADJUST Menu. (P30, 31)
User preset adjustment in MANUAL PC ADJUSTMENT. Adjustment data can be stored in the Mode 1-20.
Mode 1
Computer systems provided in the projector. The projector chooses proper system and displays it.
SVGA 1
Mode 1 and SVGA 1 are examples.
27
BASIC OPERATION
SELECT VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SYSTEM SELECT Menu icon.
Press POINT DOWN button to move a red arrow pointer to system that you want to select and then press SELECT button.
1
2
SYSTEM SELECT MENU (SDI)
SYSTEM SELECT Menu icon Displays system being selected.
Systems on this dialog box can be selected.
Custom Mode (1~15) set in DISPLAY ADJUST Menu. (P30, 31)
SYSTEM SELECT MENU (Component video)
SYSTEM SELECT Menu icon Displays system being selected.
Systems on this dialog box can be selected.
Custom Mode (1~15) set in DISPLAY ADJUST Menu. (P30, 31)
Projector automatically detects incoming Video signal, and adjusts itself to optimize its performance. When Video System is 1035i, 1080i/50 or 1080i/60, select system manually first.
If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i , 1080i/50 or 1080i/60.
Auto
COMPONENT VIDEO SIGNAL FORMAT
SDI Input
Component video (Y, Pb/Cb, Pr/Cr) Input
Projector automatically detects incoming SDI signal (480i, 575i, 1035i, 1080i/60, 1080i/50, 720p, 1080p/30 and 1080psf/30), and adjusts itself to optimize its performance. When System is 1080i/60 or 1080psf/30, select system manually first.
28
DISPLAY ADJUST
DISPLAY ADJUSTMENTS
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to DISPLAY ADJUST Menu icon.
1
Press POINT UP/DOWN button and move a red frame pointer to Screen and then press SELECT button.
2
Anamorphic
Provides image to fit the horizontal size of the screen size.
Full
Normal
Provides image in its original size.
Provides image is forcibly changed to a 4:3 image, even if the input signal is HDTV.
Aspect H
Aspect V
These adjust the horizontal and vertical scale and position of the screen. When a SELECT button is pressed, the mode changes to Scale or Position adjustment mode. Use the POINT LEFT/RIGHT button(s) to select whether you wish to adjust Scale or Position, and then use the POINT UP/DOWN button(s) to adjust the values.
DISPLAY ADJUST MENU
DISPLAY ADJUST Menu icon
Set a red frame pointer to item and press SELECT button.
3
Press POINT UP/DOWN button to move a red arrow to level that you want to set and then press SELECT button.
SCREEN ADJUSTMENTS
Select screen by pressing Screen button on Remote Control Unit.
Full
Normal
Anamorphic
SCREEN ADJUSTMENT (DIRECT)
29
DISPLAY ADJUST
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to DISPLAY ADJUST Menu icon.
1
2
Press POINT DOWN button to move a red frame pointer to AUTO PC Adj. icon and then press SELECT button twice. This Auto PC Adjustment can be also executed by pressing AUTO PC ADJ. button on Side Control or on Remote Control Unit.
Auto PC Adj.
Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in SYSTEM SELECT Menu (P26). Refer to step 3 of MANUAL DISPLAY ADJUSTMENT section (P31).
NOTE
Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 30, 31.)
Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and 480i, 575i, 480p, 575p, 720p (HDTV), 1035i (HDTV), 1080i/50 (HDTV) or 1080i/60 (HDTV) is selected on SYSTEM SELECT Menu (P26).
DISPLAY ADJUST MENU
DISPLAY ADJUST Menu icon
Set a red frame pointer to item and press SELECT button.
30
DISPLAY ADJUST
MANUAL DISPLAY ADJUSTMENTS
This projector can automatically tune to display signals from most computers and video equipments currently distributed. However, some computers and video equipments employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual display adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 20 independent memory areas {Mode 1~15 for video equipments and computers (digital signal), Mode 16 ~ 20 for computers (analog signal)} to memorize those parameters manually adjusted. This enables you to recall setting for a specific computer and video equipment whenever you use it.
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon.
1
2
Press POINT UP/DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Adjustment dialog box will appear. Press POINT LEFT/RIGHT button to adjust value.
Adjusts an image as necessary to eliminate flicker from display. Press POINT LEFT/RIGHT button to adjust value. (From 0 to 31.)
Fine sync
Adjust the number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image.
Total dots
Adjusts horizontal picture position. Press POINT LEFT/RIGHT button(s) to adjust position.
Horizontal
Adjusts vertical picture position. Press POINT LEFT/RIGHT button(s) to adjust position.
Vertical
Shows status (Stored / Free) of selected Mode.
Selected Mode
DISPLAY ADJUST MENU
DISPLAY ADJUST Menu icon
Move a red frame icon to item and press SELECT button.
Press POINT LEFT/RIGHT button to adjust value.
Press SELECT button at this icon to display next items.
Selects area displayed with this projector. Select resolution at Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.
Display area H
Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.
Display area V
Display area
Press SELECT button at Display area icon and Display area dialog box appears.
Press SELECT button at this icon to display previous items.
Press POINT LEFT/RIGHT button to adjust value.
31
DISPLAY ADJUST
Press SELECT button to show information of computer selected.
Current mode
Adjusts clamp position. When image has a dark bar(s), try this adjustment.
Clamp
Press SELECT button at Current mode icon to show information of computer connected.
Current mode
Press SELECT button at this icon to display previous items.
Reset
Store
Closes DISPLAY ADJUST MENU.
Quit
Other icons operates as follows.
3
To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 20 that you want to store and then press SELECT button.
Reset all adjust parameters on adjustment dialog box to previous figure.
Mode free
To store adjustment data.
To clear adjustment data.
To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button.
Mode free icon
Store icon
Vacant Mode
Shows values of Total dots Display area H and Display area V”.
Terminal board and System of input signal.
Press POINT LEFT/RIGHT buttons to display right page.
Press POINT UP/DOWN buttons to display next/previous page.
Close this dialog box.
This Mode has parameters being stored.
Shows values of scale and position of Aspect H and Aspect V .
32
IMAGE ADJUST MENU
Move a red frame pointer to item to be selected and then press SELECT button.
IMAGE ADJUST Menu icon
IMAGE ADJUSTMENTS
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE ADJUST Menu icon.
1
3
Press POINT UP/DOWN button to move a red arrow to level that you want to set and then press SELECT button.
Normal picture level preset on this projector for AV mode.
Standard (AV)
Picture level with improved halftone for graphics.
Real
Normal picture level preset on this projector for PC mode.
Standard (PC)
Picture level adjusted for picture with fine tone.
Cinema
User preset picture adjustment in IMAGE ADJUST Menu (P33-36).
IMAGE 1~10
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard (AV), Cinema, Standard (PC), Real and Image 1 ~ Image 10 by pressing IMAGE button on Side Control or on Remote Control Unit. Select image level Image 1 ~ Image 10 by pressing IMAGE 1 ~ IMAGE 10 buttons on Remote Control Unit.
IMAGE button
Standard (AV)
Cinema
Standard (PC)
Real
Image 1
Image 10
Normal picture level preset on this projector for AV mode.
Standard (AV)
Picture level adjusted for picture with fine tone.
Cinema
IMAGE 1 ~ IMAGE 10 buttons
Image 1
Image 10
Normal picture level preset on this projector for PC mode.
Standard (PC)
Picture level with improved halftone for graphics.
Real
User preset picture adjustment in IMAGE ADJUST Menu (P33-36).
IMAGE 1~10
IMAGE LEVEL SELECT (MENU)
2
Press POINT UP/DOWN button to move a red frame pointer to image icon and then press SELECT button.
DISPLAY ADJUST
33
DISPLAY ADJUST
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST Menu icon.
1
2
Press POINT UP/DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).
IMAGE ADJUST MENU
Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)
Contrast
Brightness
Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)
Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)
Color
Tint
Press POINT LEFT/RIGHT buttons to adjust value.
Move a red frame pointer to item to be selected and then press SELECT button.
IMAGE ADJUST Menu icon
Press SELECT button at this icon to display previous items.
Press POINT LEFT/RIGHT buttons to adjust value.
Press SELECT button at this icon to display next items.
Press POINT LEFT button to soften the image, and POINT RIGHT button to sharpen the image. (From 0 to 15.)
Sharpness
Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)
White balance (Blue)
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color temp. level that you want to select. (XLow, Low, Mid or High)
Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to enhance the detail of the image. (From 0 to 15.)
Detail enhancer
Press SELECT button at this icon to display next items.
IMAGE LEVEL ADJUSTMENTS
34
Press POINT LEFT/RIGHT button(s) to change progressive scan mode. Dialog box display is changed to Off and progressive scan mode to off. Press POINT LEFT/RIGHT button(s) again, progressive scan mode to on.
Press POINT LEFT/RIGHT button(s) to change noise reduction mode. Dialog box display is changed to Off, L1, L2 or L3 to reduce noise (rough parts) of image. Off ······· Noise reduction OFF position. L1 ········ Noise reduction LEVEL 1 position. L2 ········ Noise reduction LEVEL 2 position. L3 ········ Noise reduction LEVEL 3 position.
Noise reduction
Progressive scan
Press POINT LEFT/RIGHT buttons to change position.
Press SELECT button at this icon to display first items.
Auto picture control
Press either POINT LEFT button or POINT RIGHT button to Auto picture control position that you want to select . (Off, L1 or L2) Off ······· Auto picture control OFF position. L1 ········ Auto picture control LEVEL 1 position. L2 ········ Auto picture control LEVEL 2 position.
Auto lamp control
The projector reduce the brightness and set into the low power consumption mode. When this function is On, the brightness is adjusted automatically to a level that is suitable for the screen.
Press SELECT button at this icon to display previous items.
DISPLAY ADJUST
Color Management
The Color management function can be used to adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required. The projector lets you replace up to eight colors for each image.
1
Press the POINT UP/DOWN button to move the red frame point­er to "COLOR MANAGEMENT", and then press the SELECT button. The COLOR MANAGEMENT menu will appear and pointer mode will be enabled. The image that was being project­ed when the button was pressed will be paused, and the COLOR MANAGEMENT POINTER will appear.
Use the POINT buttons to move the pointer to a section of the paused image that contains the color that you would like to adjust, and then press the SELECT button. The mode will change to COLOR SELECTION mode, and the color in the cen­ter of the pointer will be selected and adjustment will be possi­ble.
2
Use the POINT buttons to adjust the level and phase of the color, and then press the SELECT button to confirm the setting. Next, use the POINT buttons to adjust the gamma correction for the color, and then press the SELECT button to accept the set­ting. When the SELECT button is pressed, the mode will change to LIST mode.
3
COLOR MANAGEMENT POINTER
POINTER MODE
35
DISPLAY ADJUST
To move the red frame pointer to "MENU", and then press the SELECT button. The message "OK"? is displayed. Move the pointer to
[Yes] and then press SELECT button.
The COLOR MANAGEMENT menu will be exited and the display will return to the IMAGE ADJUST menu. (At this time, the image will stop being paused and normal projection will resume.) After chang­ing the COLOR MANAGEMENT settings, use the IMAGE ADJUST menu to store the changed settings.
The check mark will be cleared and the effect of the setting adjustment for that line on the projected images will be momentarily canceled.
4
CANCEL
COLOR SELECTION MODE
The mode will return to the pointer mode (even if you press the MENU key on the projector or the remote control). (You will need to reselect and re-adjust the color in this case.)
QUIT
The COLOR MANAGEMENT menu will be exited and the display will return to the normal projection screen, but any settings that have been changed will not be stored. To store the changed settings, be sure to select "LIST" using the POINT buttons and change to the next mode (LIST mode).
LIST MODE
The mode will return to COLOR SELECTION mode so that you can re-adjust the setting for the color in that line. This option is not avail­able if the check mark has been cleared by the operation immediate­ly above.)
COLOR PALETTE
The setting adjustment for the color in that line will be canceled.
DEL
ALL DEL
The setting adjustment for the colors in all lines will be canceled.
COLOR M.
The mode will return to POINTER mode.
COLOR SELECTION MODE
CANCELLIST
QUIT
Level and phase adjustment palette.
Gamma adjustment palette.
LIST MODE
COLOR PALETTE
DEL
ALL DEL
COLOR M.MENU
36
DISPLAY ADJUST
Reset all adjustment to previous figure.
Reset
Store
Closes IMAGE MENU.
Quit
Other icons operates as follows.
To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image 1 to 10 where you want to set and then press SELECT button.
Message "OK?" is displayed. Move
pointer to [Yes] and then press SELECT button.
Image Level Menu Move a red frame pointer to any of Image 1 to 10 where you want to set and then press SELECT button.
Store icon Press SELECT button at this icon to store the adjustment.
Gamma balance
The Gamma balance function can be used to adjust the R, G, B Gamma balance of the screen.
1
Press the POINT UP/DOWN button to move the red frame point­er to "Gamma balance", and then press the SELECT button. The Gamma balance adjust menu will appear.
2
Use the POINT LEFT/RIGHT buttons to move the adjust point (R P1, R P2, R P3, G P1, G P2, G P3, B P1, B P2, B P3) and press the POINT UP/DOWN button to adjust value.
Reset
Quit
Press the POINT LEFT/RIGHT button to move the red frame pointer to "Quit", and then press the SELECT button. The Gamma balance adjust menu will be exited.
Press the POINT LEFT/RIGHT button to move the red frame pointer to "Reset", and then press the SELECT button. Reset the adjustment value to previous figure.
37
SETTING
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red-frame pointer to SETTING icon.
1
2
Language
Press POINT DOWN button to move a red-frame pointer to item that you want to set and then press
SELECT button. Setting
dialog box appears.
When pressing SELECT button at Language, Language Menu appears.
SETTING MENU
Language used in ON-SCREEN MENU is selectable from among English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean and Japanese.
SETTING Menu icon
Set a red frame pointer to item and press SELECT button.
Lamp Mode
This Projector is equipped with 4 Projection Lamps and a number of using lamps can be switched to 4 lamps or 2 lamps. Using 2 lamps maintain life of Projection Lamps.
To change over Lamp Mode
1. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select SETTING and press SELECT button. Setting dialog box appears.
2. Press POINT DOWN button to move a red frame pointer to Lamp mode. Set "4 lamps mode" or "2 lamps mode" by pressing POINT LEFT/RIGHT button(s). When Lamp Mode is set from "4 lamps mode" to "2 lamps mode" image becomes little darker. When Lamp Mode is set from "2 lamps mode" to "4 lamps mode" image become brighter gradually.
Display
This function decides whether to display On-Screen Displays.
On ··· Shows all the On-Screen Displays. Off ··· Sets On-Screen Displays disappeared except;
ON-SCREEN MENU
Power off? message
P-TIMER
No signal message
Wait a moment message
Blue back
When this function is On, this projector will produce a blue image instead of the video noise on the screen when any input source is unplugged or turned off.
Move a pointer to item and then press POINT LEFT/RIGHT button(s).
Optional Control Number
Refer to page 11.
Menu size
This function decides to display On-Screen Displays size.
Normal ··· Shows normal size the On-Screen Displays. Double ··· Shows double size the On-Screen Displays.
38
SETTING
Logo
When this function is On, projector displays logo when starting up.
Menu position
Rear
When this function is On, picture is left / right reversed. This function is used to project the image to a rear projection screen.
Rear function
Press SELECT button at this icon to display next items.
Press SELECT button at this icon to display previous items.
This function is used to adjust the on-screen menu display position. When a SELECT button is pressed, the adjustment screen is displayed (arrows appear). Use the POINT UP/DOWN/LEFT/RIGHT button(s) to adjust the position. After making the adjustment, press a SELECT button to return to the Menu screen.
39
SETTING
On start
When this function is On, projector is automatically turned on just by connecting AC Power cord to a wall outlet.
Note ; B e sure to turn projector off properly (refer to section
TURNING OFF PROJECTOR on P22). If projector is turned off in wrong steps, On Start function does not operate properly.
Power management
Time left until Lamp off.
Remote control
This projector has eight different remote control codes; the factory­set normal code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together. For example operating projector in Code 7, both projector and Remote Control Unit must be switched to Code 7.
To change the code of Projector;
To change the Remote control code of the projector used in ON­SCREEN MENU is selectable from Code 1 to Code 8.
To change the code of the Remote Control Unit;
While pressing the MENU button, press the IMAGE button number of times corresponding to each remote control code number. (Refer to P19.)
When pressing SELECT button at Remote control, Remote control code Menu appears.
This projector is equipped with a power management function. When the input signal is interrupted and any button is not pressed for 30 seconds or more, the power management function operates in order to reduce power consumption and conserve lamp operating time. The factory default settings for power management are "Ready" and "5 Min".
The power management function is canceled.
When a SELECT button is pressed, the adjustment screen is displayed.
Use the POINT LEFT/RIGHT button(s) to select the power management function mode ("Off", "Ready" or "Shut down").
Use the POINT DOWN button to move the pointer to the time setting, and then use the POINT LEFT/RIGHT button(s) to set the time (1 minute to 30 minutes).
If "Shut down" is selected
If "Off" is selected
If "Ready" is selected
OPERATION
1) If the input signal is interrupted and any button is not pressed for 30 seconds or more, the message "No signal" and the timer display appears on the screen. Then the count-down starts for the time being set.
2) When the set time is elapsed, the lamp will be switched off and lamp cooling starts. The READY indicator will be switched off while the lamp cooling is in progress, and the projector cannot be operated during this time.
3) When the lamp cooling is completed, the READY indicator starts flashing to notify the operator that power management mode is active. In this condition, the lamp will turn on and images will be projected if a signal starts being input or the projector is operated.
2) When the set time is elapsed, the lamp will be switched off and lamp cooling starts. The READY indicator will be switched off while the lamp cooling is in progress, and the projector cannot be operated during this time.
3) When the lamp cooling is completed, the power switches off.
40
SETTING
Lamp counter reset
Key lock
Factory default
Press POINT UP/DOWN button to move a red frame pointer to Factory default and then press
SELECT button. The message "Return to Factory default?" is displayed. Move the pointer to [Yes] and then press SELECT button.
Another confirmation dialog box appears and select [Yes]
and then
press SELECT button.
Return the projector to Factory default.
This function returns all setting values except for the lamp counter to the factory default settings.
This function locks the operation of the projector's control panel and the remote control.
This locks operation of the projector's control panel.
This locks operation of the remote control.
This cancels the Key lock function.
If the projector's control panel accidentally becomes locked and you do not have the remote control nearby, turn the MAIN ON/OFF switch to OFF. And then while pressing a SELECT button, return the MAIN ON/OFF switch to ON again. This will cancel the projector's control panel lock.
Be sure to reset Lamp Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon.
1
Press POINT DOWN button to move a red frame pointer to Lamp counter reset and then press
SELECT button.
2
Do not reset Lamp Replace Counter except after Projection lamp is replaced.
Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.
4
Move arrow to replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4) and then press
SELECT button. Message "Lamp replace counter Reset?" is displayed. Move pointer to [Yes] and then press SELECT button.
3
NOTE: Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
Closes SETTING MENU.
Quit
READY
LAMP
LAMP
REPLACE
WARNING
TEMP.
41
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from AC outlet.
1
2
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal heat build up and adversely affect life of a projector. Clean Air Filter following steps below:
3
4
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on liquid crystal panel, lens, or optical elements inside it. This condition may degrade quality of projected image. When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
Pull out air filter from a projector.
Pulling up center frame of air filter top, separate air filter top and sheet from air filter base.
Clean each parts with brush or wash out dust and particles. Be sure to dry them out.
Assemble sheet and air filter and replace air filter to a projector.
5
AIR FILTER
AIR FILTER TOP
AIR FILTER BASE
SHEET
CAUTION
Do not operate a projector with Air Filter removed. Dust may accumulate on LCD Panel and Mirror degrading picture quality. Do not put small parts into Air Intake Vents. It may result in malfunction of a projector.
MAINTENANCE
WARNING TEMP. INDICATOR
Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are not obstructed.
Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING on this page.
1
2
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be malfunctioning. Contact the service station.
3
The Warning Temp. Indicator flashes red to let you know the internal temperature of the projector exceeds the normal level. If the temperature goes up further, the projector will be turned off automatically and the Ready indicator will go out. (The Warning Temp. Indicator continues flashing.) After the cooling-off period, the Ready Indicator lights on again and the projector can be turned on by pressing the On/Off button on the remote control unit or on the side control. When you turn on the projector, the Warning Temp. Indicator will go out. If the Warning Temp. Indicator is still flashing, check the followings;
FRONT INDICATORS
When both of the Warning Temp. and Ready indicators are flashing:
Warning Temp. Indicator
Ready Indicator
When the projector detects an internal problem, it will shut down automatically and both of the Warning temp. and Ready Indicators starts flashing. In this condition, the projector cannot be turned on even if you press the On/Off button on the remote control unit or on the side control. If this case happenes, disconnect and reconnect the AC power cord, and then turn on the projector again to check its operation. If the projector shuts down again or fails to be turned on, the internal check and repair will be required. Plug off the AC power cord and contact service station.
WARNING
TEMP.
READY
LAMP
REPLACE
LAMP
REAR INDICATORS
APPENDIX
42
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp Management Function. Lamp Management Function detects status of all lamps and shows status on screen or on LAMP REPLACE indicator. This function also automatically controls Lamp Mode when any of lamps is out for end of life or malfunctions.
Projection Lamp lights normally.
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them becomes out. Check number of lamp on Lamp Status Display and replace lamp.
Yellow Lamp
Dim Lamp
X Mark on Lamp
Red Lamp
LAMP REPLACE INDICATOR
Projection Lamp is turned off.
Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (LAMP REPLACE indicator lights yellow.)
(LAMP REPLACE indicator flashes yellow.) Projection lamp is defective or fails to be turned on. Restart a projector on, and make sure lamp is on. If this mark still appears, replace lamp corresponding with number marked X.
LAMP STATUS DISPLAY
Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp. When any of 4 lamps becomes out, Lamp Mode is changed over from 4 lamps to 2 lamps. And when any of 2 lamps are out, a projector operates with 1 lamp. Lamp Mode can be switched to 4 lamps or 2 lamps manually. Refer to SETTING section on page 37
.
4 LAMP MODE
2 LAMP MODE (Example)
1 LAMP MODE (Example)
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2, Input 3 or input 4). This shows status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to following for each status.
30
INPUT AND LAMP STATUS
APPENDIX
43
APPENDIX
Check number of lamp to be replaced on Lamp Status Display.
Remove two screws on Lamp Cover and press button to open Lamp Cover. (See right figure.)
1
3
Loosen two screws and pull out Lamp Assembly to be replaced by grasping handle.
4
Turn off a projector and disconnect AC Power Cord. Allow a projector to cool down for at least 45 minutes.
2
Replace Lamp Assembly with a new one and tighten two screws. Make sure Lamp is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp Cover and tighten two screws.
5
7
8
Connect AC Power Cord to a projector and turn a projector on.
Reset Lamp Replacement Counter. (Refer to section "Lamp Counter Reset" on page 40.)
NOTE : Do not reset LAMP REPLACEMENT COUNTER when
lamp is not replaced.
BUTTON
SCREWS
LAMP COVER
SCREWS
Make sure which number of lamp needs to be replaced on Lamp Status Display. Figure shows case of replacing LAMP 2.
LAMP 1
LAMP 2
LAMP 3
LAMP 4
CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 4 lamps at a time.
LAMP REPLACEMENT
When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.
For continued safety, replace with a lamp assembly of the same type. Do not drop a lamp assembly or touch a glass bulb! The glass can shatter and may cause injury.
Allow a projector to cool, for at least 45 minutes before you open Lamp Cover. The inside of a projector can become very hot.
REAR INDICATORS
CAUTION
FRONT INDICATORS
LAMP REPLACE INDICATOR
LAMP
READY
WARNING
TEMP.
LAMP
REPLACE
LAMP
READY
WARNING
TEMP. LAMP
REPLACE
44
APPENDIX
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.
Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual.) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projectors AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.
LAMP HANDLING PRECAUTIONS
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer.
Model No. of your projector : PLV-HD150
Replacement Lamp Type No. : POA-LMP95
(Service Parts No. 610 323 5394)
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch lens.
When a projector is not in use, replace lens cover.
1
3
Lightly wipe cleaning cloth over lens.
2
Follow these steps to clean projection lens:
45
Check audio cable connection from audio input source.
Adjust audio source.
Press VOLUME (+) button.
Press MUTE button.
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 12 ~ 15.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn a computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.)
6. If problem still exists, check following chart.
No power.
Plug a projector into your AC outlet.
Turn MAIN ON/OFF switch to ON.
Press POWER ON/OFF switch to ON.
Make sure READY Indicator lights.
Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be turned on by pressing Power ON-OFF button.
Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY indicator flashes, a projector cannot be turned on. (See "TURNING ON/OFF PROJECTOR" section on page 22.)
Check Projection Lamp. (Refer to page 43.)
Image is out of focus.
Adjust focus of a projector.
Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears.
Picture is Left/Right reversed.
Check Rear feature. (See SETTING section on page 38.)
Problem: Try these Solutions
Some displays are not seen during Operation.
Check Display feature.(See SETTING section on page 37.)
No image.
Check connection between your computer or video equipment and a projector.
When turning a projector on, it takes about 30 seconds to display an image.
Check system that you select is corresponding with your computer or video equipment.
Make sure temperature is not out of Operating Temperature (5°C ~ 30°C).
No sound.
APPENDIX
46
APPENDIX
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOT­ING" section on pages 45-46. To correct failure, try "Solutions".
If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or store where you purchased unit. Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.
Remote Control Unit does not work.
Check batteries.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4 (5m).
Check transmitted signal mode from Remote Control Unit. (See SETTING section on page 39.)
Problem: Try these Solution
47
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.
• • • on : red
• • • dim
• • • off
• • • flashing : red
When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow,
replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp.
The projector is OFF. (The MAIN switch OFF position or the AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON­OFF button.
The temperature inside the projector is abnormally high. The projector cannot be turned on. When the projector is cooled down enough and the temperature returns to normal, the READY indicator lights green and the projector can be turned on. (The WARNING TEMP. indicator keeps flashing.) Check and clean the Air Filter.
The projector is being cooled down. It cannot be turned on until the READY indicator lights green.
Projector Condition
The projector is operating normally.
The projector is cooled down enough and the temperature returns to normal. When turning on the projector, the WARNING TEMP. indicator stops flashing. Check and clean the Air Filter.
Indicators
READY
green
LAMP
red
The projector detects an abnormal condition and cannot be turned on. Unplug the AC Power Cord and plug it again to turn on the projector. If the projector is turned off again, disconnect the AC Power Cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause electric shock or a fire hazard.
The projector is in the Power management mode.
WARNING
TEMP.
red
LAMP
REPLACE
yellow
• • • on : green
• • • flashing : green
48
APPENDIX
SDI 1
SYSTEM
Input 2
Y, Pb/Cb, Pr/Cr
SYSTEM
3)
1)
Input 1
RGB
Input
2)
System
System
SVGA 3
Custom
SVGA 1
SVGA 2
Auto PC Adj.
Fine sync
Total dots
Horizontal
Vertical
Current mode
Clamp
Display area
Display area H
Display area V
Store
Quit
0 - 31
Display adjust
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 720
1280 x 1024
Quit
1600 x 1200
Yes/No
1)
1080i/50
1035i
Auto
1080i/60
575p
480p
720p
575i
Mode 1 ~ Mode 20
640 x 480
Reset
SYSTEM
2)
Input 3
RGB (Analog)
RGB (Scart)
SYSTEM
1)
RGB (PC Digital)
SYSTEM
2)
SYSTEM
1)
MENU TREE
SDI 2
SYSTEM
3)
RGB (AV HDCP)
SYSTEM
2)
480i
Custom
3)
System
1035i
1080i/60
480i
575i
720p
1080i/50
1080p/30
1080psf/30
Custom
Screen
Normal
Anamorphic
Full
Aspect H
Position -15 ~ 15
Scale -32 ~ 32
Aspect V
Position -15 ~ 15
Scale -32 ~ 32
1920 x 1080
Quit
Yes/No
Mode free
49
APPENDIX
Lamp 2
Sound
Mute
Quit
Volume
Built-in SP.
On/Off
On/Off
0 - 63
Language
Setting
English
German
French
Italian
Spanish
Portuguese
Dutch
Swedish
Chinese
Korean
Japanese
On/Off
On/Off
On/Off
Off/Ready/Shut down
On/Off
4 Lamp/2 Lamp
Lamp 1
Menu position
Power management
On start
Lamp mode
Remote control code
Lamp counter reset
Code 1
Code 3
Code 4
Code 5
Code 6
Code 7
Code 8
Quit
Quit
Russian
Logo
Control panel
Key lock
Remote control
Off
Yes/NoFactory default
Blue back On/Off
Display
Rear
Code 2
Image adjust
Contrast
Brightness
Color
Red
Green
Blue
Sharpness
Store
Quit
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 15
Image 1
Image 2
Image 3
Image 4
Image 5
Tint 0 - 63
Gamma
Noise reduction
0 - 15
Off/L1/L2/L3
Reset Yes/No
Auto picture control Off/L1/L2
Progressive Off/On
Color temp.
XLow/Low/Mid/High
Treble
0 - 63
Bass
0 - 63
Normal/Double
Menu size
Quit
1 ~ 30 minutes
Lamp 3
Lamp 4
Quit
Yes/No
Yes/No
Yes/No
Yes/No
Image Standard (AV)
Standard (PC)
Real
Image 1 ~ Image 10
Quit
Cinema
Detail enhancer 0 - 15
Auto lamp control Off/On
Image 6
Image 7
Image 8
Quit
Image 9
Image 10
Quit
Color management
Gamma balance
50
APPENDIX
Owners Manual AC Power Cord Wireless/Wired Remote Control Transmitter and Batteries Remote Control Cable DVI-VGA Cable and DVI Cable MAC/VGA Adapter 6 Types Light-Block Sheet (For option lens) 2 Types Lens Attachment (For option lens) Protective Dust Cover
TECHNICAL SPECIFICATIONS
1.65" TFT Active Matrix type, 3 panels
Multi-media Projector
83.9 lbs (38 kg)
22.9" x 10" x 30.9" (581 mm x 252 mm x 783 mm)
1920 x 1080 dots
6,220,800 (1920 x 1080 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
Up, Down, Left and Right
1100 TV lines (HDTV)
Projector Type
Net Weight
Dimensions
(W x H x D)
Panel Resolution Number of Pixels Color System
Scanning Frequency Horizontal Resolution
LCD Panel System
300 watt type x 4
Projection Lamp
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60
High Definition TV Signal
H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz
Motorized Lens Shift
BNC Type x 3 (SDI Input 1, SDI Input-2 and SDI Output)
Input 1 Jacks
BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L) and DIN 8-pin (Control port)
Input 2 Jacks
DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L) and DIN 8-pin (Control port)
Input 3 Jacks
Specifications are subject to change without notice.
LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
Accessories
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
41 ˚F ~ 86 ˚F (5 ˚C ~ 30 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Built-in Speakers
Operating Temperature Storage Temperature
0˚ to 5.7˚
Feet Adjustment
AC 240 V (8.0 A Max. Ampere), 50 / 60 Hz
Voltage and Power Consumption
Serial port in (DB 9), Serial port out (DB 9), USB port and Audio Monitor out (RCA Type R and L)
Other Jacks
Power Source : AA, UM3 or R06 Type x 2 Operating Range : 16.4 (5m) / ±30˚ Dimensions : 2.0 x 1.0 x 7.1 (50mm x 27mm x 118mm) Net Weight : 0.34 lbs (154 g) (including batteries)
Remote Control Transmitter
51
APPENDIX
CONFIGURATIONS OF TERMINALS
DVI-I TERMINAL (DIGITAL/ANALOG)
This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this terminal with DVI cable (supplied).
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock DDC Data Analog Vert. sync
1
5
2
4
3
6 7 8
Pin Configuration
T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power Ground (for +5V) Hot Plug Detect
9
13
10
12
11
14 15 16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield T.M.D.S. Clock+ T.M.D.S. Clock–
17
21
18
20
19
22 23 24
Analog Red Input
Analog Ground (R/G/B)
Analog Green Input
Analog Horiz. sync
Analog Blue Input
C1
C5
C2
C4
C3
----­RxD TxD
-----
Ground
-----
-----
-----
1 2 3 4 5 6 7 8 9 -----
Connect serial port output terminal of computer to this terminal with Serial Cable (not supplied).
Pin Configuration
SERIAL PORT IN/OUT TERMINAL
Vcc
- Data
+ Data
Ground
1 2 3 4
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port Cable (not supplied).
C1
C2
1
2
3
4
5
6
7
9
10
11
17
18
19
8
12
13
14
15
16
20
21
22
23
24
C3
C4
C5
12345
6789
2
1
34
52
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 230 MHz of Dot Clock.
–––––––– (Interlace)
1024 x 768
(Interlace)
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
VGA 1
640 x 480 31.47 59.88 VGA 2 720 x 400 31.47 70.09 VGA 3 640 x 400 31.47 70.09 VGA 4 640 x 480 37.86 74.38 VGA 5 640 x 480 37.86 72.81 VGA 6 640 x 480 37.50 75.00
MAC LC13
640 x 480 34.97 66.60
MAC 13 640 x 480 35.00 66.67
MAC 16 832 x 624 49.72 74.55
MAC 19 1024 x 768 60.24 75.08 MAC 21
1152 x 870
68.68 75.06
UXGA 3 1600 x 1200 87.50 70.00 UXGA 4 1600 x 1200 93.750 75.00
SVGA 1 800 x 600 35.156 56.25 SVGA 2 800 x 600 37.88 60.32 SVGA 3 800 x 600 46.875 75.00 SVGA 4 800 x 600 53.674 85.06 SVGA 5 800 x 600 48.08 72.19 SVGA 6 800 x 600 37.90 61.03 SVGA 7 800 x 600 34.50 55.38 SVGA 8 800 x 600 38.00 60.51 SVGA 9 800 x 600 38.60 60.31
SVGA 11 800 x 600 38.00 60.51
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
XGA 11 1024 x 768
XGA 13 1024 x 768 XGA 14 1024 x 768
61.00 75.70
XGA15 1024 x 768
46.90 58.20
XGA 8 1024 x 768
47.00 58.30
XGA 9
1024 x 768
(Interlace)
58.03 72.0
SXGA 1 1152 x 864 SXGA 2 1280 x 1024
63.48 79.35
SXGA 3 1280 x 1024
36.00 87.17
SXGA 4
1280 x 1024
64.20 70.40
SXGA 5 1280 x 1024
62.50 58.60
SXGA 6 1280 x 1024
63.90 60.00
SXGA 7
1280 x 1024
63.34 59.98
SXGA 8 1280 x 1024
63.74 60.01
SXGA 11
1152 x 900
71.69 67.19
SXGA 12
1152 x 900
81.13 76.107
SXGA 13
1280 x 1024
(Interlace)
63.98 60.02
SXGA 14
1280 x 1024
(Interlace)
61.20 65.20
71.40 75.60
50.00 86.00
720p
––––––––
(Progressive)
50.00 94.00
45.00 60.00
XGA 1 1024 x 768 XGA 2 1024 x 768 XGA 3 1024 x 768 XGA 4 1024 x 768
48.36 60.00
68.677 84.997
XGA 6 1024 x 768
60.023 75.03
XGA 7 1024 x 768
56.476 70.07
48.50 60.02
44.00 54.58
SXGA 9 1280 x 1024
SXGA 10 1280 x 960
79.976 75.025
60.00 60.00
SXGA 15 1280 x 1024 SXGA 16 1280 x 1024 SXGA 17 1152 x 900 SXGA 18
1280 x 1024
(Interlace)
63.37 60.01
76.97 72.00
61.85 66.00
46.43 86.70
SXGA 19
1280 x 1024 63.79 60.18
XGA 5 1024 x 768 60.31 74.92
VGA 7 640 x 480 43.269 85.00
575i
––––––––
(Interlace)
15.625 50.00
480i
––––––––
(Interlace)
15.734 60.00
1080i/60
–––––––– (Interlace)
33.75 60.00
1035i
––––––––
(Interlace)
33.75 30.00
SVGA 10 800 x 600 32.70 51.09
SXGA 20
1280 x 1024 91.146 85.024
480p
––––––––
(Progressive)
31.47 59.88
XGA 10 1024 x 768 62.04 77.07
1080i/50
28.125 50.00
SXGA 21
1400 x 1050 63.90 60.00
MAC
1280 x 960 75.00 75.08
UXGA 1
1600 x 1200 75.00 60.00
UXGA 2
1600 x 1200 81.25 65.00
XGA 12
35.522 86.96
575p
––––––––
(Progressive)
31.25 50.00
MAC
1280 x 1024 80.00 75.08
WXGA 3 1376 x 768 48.36 60.00 WXGA 4 1360 x 768 56.16 72.00
WXGA 1
1366 x 768 48.36 60.00
WXGA 2
1360 x 768 47.70 60.00
53
APPENDIX
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
D-VGA
640 x 480 31.47 59.94
D-480p
720 x 480
(
Progressive
)
31.47 59.88
D-575p
768 x 575
(
Progressive
)
31.25 50.00
D-SVGA
800 x 600 37.879 60.32
D-XGA
1024 x 768 43.363 60.00
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
D-SXGA1
1280 x 1024
63.98
60.02
D-SXGA2
1280 x 1024
60.276 58.069
D-SXGA3
1280 x 1024 31.65
29.8
D-720p
1280 x 720
(
Progressive
)
45.00 60.00
D-1035i
1920 x 1035
(Interlace)
33.75 30.00
When a input signal is digital from DVI terminal, refer to chart below.
D-1080i/60
1920 x 1080
(
Interlace
)
33.75 30.00
D-1080i/50
1920 x 1080
(Interlace)
28.125 25.00
D-WXGA1
1366 x 768 48.36 60.00
D-WXGA2
1360 x 768 47.70 60.00
D-WXGA3
1376 x 768 48.36 60.00
D-WXGA4
1360 x 768 56.16 60.00
D-UXGA
1600 x 1200
75.00
60.00
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, give the name and Type No. to the sales dealer.
HDB 15 pin-SCART 21 pin Cable Type No. : POA-CA-SCART
Terminal Board (Y/C) Type No. : POA-MD03VD2
Terminal Board (Faroudja) Type No. : POA-MD09VD3
Network Board Type No. : POA-MD13NET
Printed in Japan Part No. 610 324 0190 (1AA6P1P4945-- M4ZA)
SANYO Electric Co., Ltd
Loading...