Sanyo PLV-HD10 User Manual

Owner's Manual

PLV-HD10

Multimedia Projector

MODEL

✽ Projection lens is optional.

2

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales
dealer where you purchased the projector or the service center.

TO THE OWNER

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

● This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.
Eye damage could result. Be especially careful that children do not stare directly into the beam.

● This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector

cabinet for allowing air circulation and cooling the projector.
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your
projector, and can also be dangerous.

● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.

● If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

SIDE and TOP

REAR

CAUTION

Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.

Ne puet être utillisé dans une salle d’ordinateurs telle
que définie dans la norme ANSI/NFPA 75 Standard for
Protection of Electronic Computer/Data Processing
Equipment

20cm

50cm 50cm

1m

3

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before
the product is operated.

Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.

An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.

Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.

The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.

This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.

Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.

4

COMPLIANCES

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin
face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the
same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug
(i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow ············ Earth
Blue ································· Neutral

Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked
by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.

CAUTION!

This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator
can be asked to take adequate countermeasures.

ASA

GROUND

5

TABLE OF CONTENTS

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its

respective corporation.

FEATURES AND DESIGN 6

BEFORE OPERATION 16

DISPLAY ADJUST 28

SETTING 35

APPENDIX 39

PREPARATION 7

NAME OF EACH PART OF PROJECTOR 7
SETTING-UP PROJECTOR 8

CONNECTING AC POWER CORD 8
LENS INSTALLATION 9
POSITIONING PROJECTOR 9
LENS SHIFT ADJUSTMENT 9
PICTURE LEVEL AND TILT ADJUSTMENT 10
MOVING PROJECTOR 10

CONNECTING PROJECTOR 11

TERMINALS OF PROJECTOR 11
CONNECTING TO COMPUTER 14
CONNECTING TO VIDEO EQUIPMENT 15

SIDE CONTROLS AND INDICATORS 16
OPERATION OF REMOTE CONTROL 18

REMOTE CONTROL CODE CHANGE
AND OPERATING RANGE 19
REMOTE CONTROL BATTERIES INSTALLATION 19

OPERATING ON-SCREEN MENU 20

HOW TO OPERATE ON-SCREEN MENU 20
FLOW OF ON-SCREEN MENU OPERATION 20
MENU BAR 21

DISPLAY ADJUSTMENTS 28

SCREEN ADJUSTMENTS 28
AUTO PC ADJUSTMENT 29
MANUAL DISPLAY ADJUSTMENTS 30

IMAGE ADJUSTMENTS 32

IMAGE LEVEL SELECT 32
IMAGE LEVEL ADJUSTMENTS 33

SETTING MENU 35

MAINTENANCE 39

WARNING TEMP. INDICATOR 39
AIR FILTER CARE AND CLEANING 39
LAMP MANAGEMENT 40
LAMP REPLACEMENT 41
CLEANING PROJECTION LENS 42

TROUBLESHOOTING 43

INDICATORS AND PROJECTOR CONDITION 45
MENU TREE 46

TECHNICAL SPECIFICATIONS 48

CONFIGURATIONS OF TERMINALS 49
COMPATIBLE COMPUTER SPECIFICATIONS 50
OPTIONAL PARTS 51

BASIC OPERATION 22

TURNING ON / OFF PROJECTOR 22
ADJUSTING SCREEN 23

ZOOM ADJUSTMENT 23
FOCUS ADJUSTMENT 23
LENS SHIFT ADJUSTMENT 23
PICTURE FREEZE FUNCTION 23
NO SHOW FUNCTION 23

SOUND ADJUSTMENT 24
SELECTING INPUT SOURCE 25
SYSTEM SELECT 26

AUTOMATIC MULTI-SCAN SYSTEM 26
SELECT COMPUTER SYSTEM MANUALLY 26
SELECT VIDEO SYSTEM 27

6

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.

◆ Compatibility

This projector widely accepts various video and
computer input signals including;

● Computers

IBM-compatible or Macintosh computer up to 1600
x 1200 resolution.

● 6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL­N color system can be connected.

● Component Video

Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i­60, can be connected.

● S-Video

S-Video signal, such as a S-VHS VCR output
signal, can be connected.

◆ High Resolution Image

This projector provides 1920 x 1080 dots resolution for
computer input and 1100 horizontal TV lines. This
projector cannot display image of over 1600 x 1200 dots.
When resolution of your computer is over than 1600 x
1200, reset a computer output for lower resolution.

◆ Multi-Scan System

This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.

◆ Multilanguage Menu Display

Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese.

◆ One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.

◆ Power Management

Power Management function is provided to reduce power
consumption while a projector is not in use.
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed. Projection
Lamp is automatically turned on again when a projector
detects signal or any operation button is pressed.
This projector is shipped with this function ON.

◆ Digital Visual Interface

This projector is equipped with DVI 29-pin terminal for
connecting DVI output from a computer.

◆ Progressive Scan Function

This function converts interlace video signals into
progressive scan signals and provide fine picture quality.

◆ Motor-driven Lens Shift

Projection lens can be moved up, down left and right with
motor-driven lens shift function. This function makes it
easy to provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.

◆ Multi Versatile Platform

This projector applies various input/output terminals and
4 terminal slots for expansion to tune to diversity of
signals from computers and video equipment.

4-built-in Terminal Slots enable you to arrange any
combinations of input sources just by changing Terminal
Boards. For Terminal Boards, contact sales dealer
where you purchased a projector.

◆ Selectable Terminal Slots

◆ Network board (Optional)

Network board is an optional product to control and set
up a projector via the network cable. By accessing to the
connected projector using the web browser on your
computer. It can be controlled and set up the projector
remotely. Contact the sales dealer where you purchased
this projector for optional parts.

7

PREPARATION

8

PREPARATION

SETTING-UP PROJECTOR

This projector uses nominal input voltages of 120 V or
200-240 V AC. This projector automatically selects
correct input voltage. It is designed to work with single­phase power systems having a grounded neutral
conductor. To reduce risk of electrical shock, do not plug
into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of type of power supply being in use.
Connect a projector with peripheral equipment before
turning a projector on. (Refer to pages 12 ~ 15 for
connection.)

CONNECTING AC POWER CORD

Connect AC Power Cord (supplied) to
a projector.
AC outlet must be near this equipment
and must be easily accessible.

To POWER CORD
CONNECTOR on a
projector.

Projector side AC Outlet side

Ground

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector.
Confirm AC plug type with chart below and proper AC power cord must be used.
If supplied AC Power Cord does not match AC outlet, contact your sales dealer.

To the AC Outlet.

(120 V AC)

For Continental Europe

For the U.S.A. and Canada

For the U.K.

To the AC Outlet.

(200 - 240 V AC)

To the AC Outlet.

(200 - 240 V AC)

9

PREPARATION

POSITIONING PROJECTOR

Before setting up a projector, install Projection Lens on a Projector.

1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection
Lens, refer to manual separately attached or contact sales dealer where you purchased a projector.

2. For installation, refer to installation manual supplied to a Projector.

LENS INSTALLATION

When moving or setting up a projector, be sure to replace a Lens Cover to protect a surface. And be
careful not to hold or subject a lens to strong forces. It may damage lens, cabinet, or mechanical
parts.

Projection lens can be moved up, down, left and right with motor-driven lens shift function. This function makes
it easy to provide projected image where you want.

LENS SHIFT ADJUSTMENT

MOVED UP OR DOWN

MOVED LEFT OR RIGHT

Use LENS SHIFT button and
POINT UP/DOWN button to
move image up or down.
(Refer to page 23.)

Use LENS SHIFT button and
POINT LEFT/RIGHT button to
move image left or right.
(Refer to page 23.)

This projector is designed to project on a flat projection
surface.

ROOM LIGHT

Brightness in room has a great influence on picture
quality. It is recommended to limit ambient lighting in
order to provide best image.

This projector is equipped with cooling fan to protect it from over­heating. Pay attention to following to ensure proper ventilation
and avoid a possible risk of fire and malfunction.

● Do not cover vents with papers or other materials.

● Keep rear grill at least 3.3 feet (1 m) away from any

object.

● Make sure that there are no objects under a projector.
An object under a projector may prevent a projector
from taking cooling air through bottom vent.

VENTILATION

AIR INTAKE VENT
(BOTTOM SIDE)

EXHAUST VENT
(REAR SIDE)

SCREEN

10

PREPARATION

PICTURE LEVEL AND TILT ADJUSTMENT

Picture tilt and projection angle can be adjusted with
handles on both sides of a projector. Projection angle
can be adjusted to 5.7 degrees upper way.

1

2

3

MOVING PROJECTOR

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

● Do not drop or bump a projector, otherwise damages or malfunctions may result.

● When carrying a projector, use a suitable carrying case.

● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This

may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer and best case should be applied.

For safety, be sure to hold Carrying Handles
on both sides by 2 or more people when
moving a projector. Moving it unproperly may
result in damage of cabinet or person's
injury.
Replace lens cover and retract feet to pre­vent damage to lens and cabinet.

1

2

3

Pull up lock buttons on each side of carrying handles
and release locks.

CARRYING
HANDLE

LOCK BUTTONS

Pull carrying handles out fully until it's locked (with a
click). Move a projector by holding two handles by 2 or
more people.

To retract carrying handles, pull up lock buttons and
release lock of handles and press handles fully in until
it's locked.

LEVEL AND TILT
ADJUST HANDLE

ADJUSTABLE
FEET

Height of front feet can be adjusted
by turning handles.

KNOB

Press knob on handle. Handle pop out.

Turn handles (right and left) until picture is projected on
proper position. Adjust height of rear adjustable feet by
rotating them until projector properly stabled on table.

Press knob and retract handle.

REAR ADJUSTABLE
FEET. (Refer to P7).

Pull up lock buttons to
release lock.

11

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from
computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just
by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.

Pull out terminal by holding handle.

Remove 2 Screws on terminal.

1

2

REPLACEMENT OF TERMINAL

Tighten screws to secure terminal.

Replace terminal. Insert terminal along Guide to fit Plug
into Socket.

3

4

INPUT 1INPUT 2INPUT 3

DVI

AUDIO

CONTROL PORT

CONTROL PORT

AUDIO

R/Pr G/Y B/Pb H/HV V

(MONO)

(MONO)

R L

R L

(MONO)

AUDIO OUT

R L

R/C JACK USB

SERIAL PORT IN

SERIAL PORT OUT

RESET

INPUT 4

SDI IN1 SDI IN2 SDI OUT

INPUT/OUTPUT
TERMINALS

Screws

Guide

Socket

Plug

Figure shows DVI terminal.

SDI Terminal

5 BNC Terminal

DVI Terminal

3 TERMINAL SLOTS (Factory set)

NOTES ON ORDERING OR USING
OPTIONAL INTERFACE BOARD

When ordering or using Optional Interface Board
(Terminal Board), contact your sales dealer. When con­tacting the sales dealer, tell the Optional Control
Number (Op.cont.No.) in the menu that is located under
Language Select Menu. (See page 35.)

NOTE; When replacement of terminal board, MAIN

ON/OFF switch should be OFF position.

12

CONNECTING PROJECTOR

13

CONNECTING PROJECTOR

Connect an external audio
amplifier to these jacks.
(Refer to P14, 15.)

AUDIO OUTPUT JACKS

This projector uses a micro processor to control unit.
Occasionally, micro processor may malfunction and
need to be reset. This can be done by pressing
RESET button with a pen, which will shut down and
restart unit. Do not use RESET function excessively.

RESET BUTTON

When using Wired / Wireless Remote
Control Unit as Wired Remote
Control, Connect Wired Remote
Control Unit to this jack with Remote
Control Cable (supplied).
(Refer to page 18.)

R/C JACK

USB PORT (Series B)

15

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Video Source (example)

Audio Amplifier

Audio Speaker (stereo)

Audio Cable

(Stereo) ✽

Audio Input

Cables used for connection

• Video Cable (BNC)✽

• Audio Cable (RCA x 2) ✽

• Scart Cable ✽

• DVI-VGA Adapter ✽

(✽ = Cables are not supplied with this projector.)

NOTE :

When connecting cable, power cords of both a
projector and external equipment should be
disconnected from AC outlet. Turn a projector
and peripheral equipment on before computer is
switched on.

Audio Output

Y

Pb/Cb

Pr/Cr

RL

External Audio Equipment

AV AUDIO IN

Pr/Cr-Y-Pb/Cb

AUDIO OUT

Component video output equipment.

(such as DVD player or

high-definition TV source.)

Component Video Output

Audio Cable

(Stereo) ✽

Terminals of

a Projector

RGB Scart

21-pin Output

Scart
Cable

✽

DVI-VGA
Adapter ✽

SDI IN 1/SDI IN 2

Video Equipment with

SDI signal output/input

DVI

SDI Output SDI Input

SDI OUTPUT

Video Equipment with

Digital video signal output

DVI

Digital Video Output

BNC Cable ✽

BNC Cable ✽

SERIAL PORT IN

SERIAL PORT OUT

R/C JACK USB

AUDIO OUT

R L

(MONO)

RESET

SDI IN2

SDI IN1

R/Pr G/Y B/Pb H/HV V

SDI OUT

DVI

AUDIO

R L

AUDIO

R L

(MONO)

INPUT 1INPUT 2INPUT 3

CONTROL PORT

(MONO)

CONTROL PORT

INPUT 4

16

IMAGE button

Selects image levels.
(P32)

BEFORE OPERATION

MENU

AUTO PC ADJUST

IMAGE

SELECT

VOLUME

ZOOM FOCUS

LENS SHIFT

ON-OFF

INPUT 1/2

INPUT 3/4

SIDE CONTROLS AND INDICATORS

Adjust zoom. (P23)

INPUT 3/4 button

POWER ON–OFF button

FOCUS buttons

VOLUME buttons

Select input source either
INPUT 3 or INPUT 4. (P25)

Adjust focus. (P23)

Adjust volume. (P24)

Selects an item or adjusts
value in the On-Screen Menu.
(P20)

Executes the item selected.
(P20)

Turns the projector on or
off. (P22)

ZOOM buttons

Select LENS SHIFT function.
(P23)

SELECT button

POINT buttons

LENS SHIFT button

SIDE CONTROLS

MENU button

Open or close the On-Screen
Menu operation. (P20, 21)

INPUT 1/2 button

Select input source either
INPUT 1 or INPUT 2. (P25)

SIDE CONTROLS

REAR
INDICATORS

FRONT
INDICATORS

AUTO PC ADJ. button

Operates the AUTO PC
adjustment function. (P29)