Sanyo PLC-EF10NAL User Manual

Multimedia Projector

MODEL PLC-EF10NA

MOD PLC-EF10NAL

(

Without Lens

)

Owner's Manual

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.

Intense light source. Do not stare directly into the projection lens as possible eye damage could result. Be especially careful that children do not stare directly into the beam.

The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button. Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

If the Projector will not be used for an extended time, unplug the new Projector from the power outlet. This Projector should be set in the way indicated. Never hang the projector, or fall down on its side.

It may result in fire hazard.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

As the owner of a new Multi-media Projector, you are probably eager to try out your new projector. Before you do, we suggest that you spend a little time reading this manual to familiarize yourself with the operating procedures, so that you will receive maximum satisfaction from the many features included in your new projector. This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we have found that many service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual. You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING" section on pages 55 ~ 56 and try the solutions marked for each problem.

SAFETY PRECAUTIONS

TO THE OWNER

INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner's manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

PROJECTOR

(FRONT)

PROJECTOR

(SIDE)

WALL

50cm

50cm50cm

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

This projector is equipped with a grounding type AC line plug. Should you be unable to insert the plug into the outlet, contact your electrician. Do not defeat the safety purpose of this grounding type plug.

Follow all warnings and instructions marked on the projectors.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and powerline surges.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained.

Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector,

and can also be dangerous.

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other material, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord will be abused by persons walking on it.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

GROUND

TABLE OF CONTENTS

PAGE

FEATURES AND DESIGN 5

INTRODUCTION 5 COMPATIBILITY 5

IMAGE RESOLUTION 5 AUTOMATIC MULTISCANNING SYSTEM 5

SCREEN MODE 5 MULTILANGUAGE 5 UNPACKING THE PROJECTOR 5 TRADEMARKS 5

INSTALLATION 6-9

NAME OF EACH PART OF THE PROJECTOR 6 SETTING-UP THE PROJECTOR 7 MOVING THE PROJECTOR 8 POWER REQUIREMENTS 9

CONNECTING THE PROJECTOR 10-21

TERMINAL OF THE PROJECTOR 10-11 CONNECTING THE COMPUTER 12-19 CONNECTING THE VIDEO EQUIPMENT 20-21

BEFORE OPERATION 22-31

CONTROLS AND INDICATOR 22-23 OPERATION OF THE REMOTE CONTROL 24-28

WIRELESS REMOTE CONTROL UNIT 24-26 WIRELESS REMOTE CONTROL UNIT 27-28

CONTROL THE PROJECTOR 29-31

DIRECT OPERATION 29 MENU OPERATION 30-31

BASIC OPERATION 32-51

TURNING ON/OFF THE PROJECTOR 32 DIRECT OPERATION 33-34

MODE SELECT 33 SOUND VOLUME ADJUSTMENT 33 SOUND MUTE FUNCTION 33 ZOOM ADJUSTMENT 33 FOCUS ADJUSTMENT 33 LENS SHIFT ADJUSTMENT 33 DIGITAL ZOOM FUNCTION 34 NORMAL PICTURE FUNCTION 34 FREEZE PICTURE FUNCTION 34 NO SHOW FUNCTION 34

P-TIMER FUNCTION 34 AUTO IMAGE FUNCTION 34 CURSOR FUNCTION 34

MENU OPERATION 35-36

MODE SELECT 35 SOUND ADJUSTMENT 36 LANGUAGE ADJUSTMENT 36

VIDEO MODE 37-39

COLOR SYSTEM SELECT 37 VIDEO SOURCE SELECT 37 PICTURE IMAGE ADJUSTMENT 38 PICTURE SCREEN ADJUSTMENT 39

COMPUTER MODE 40-49

COMPUTER SYSTEM SELECT 40 COMPATIBLE COMPUTER SPECIFICATIONS 41 AUTO IMAGE FUNCTION 42 PICTURE IMAGE ADJUSTMENT 43 PICTURE POSITION ADJUSTMENT 44 PC ADJUSTMENT 45-48 PICTURE SCREEN ADJUSTMENT 49

OTHER FUNCTION SETTING 50-52

BLUE BACK 50-51 DISPLAY 50-51 REVERSE T/B 50-51 REVERSE L/R 50-51 SPLIT WIPE 50-51 POWER MANAGEMENT 50-51 USB (Mouse or Control) 50-51 REMOTE CONTROL (Mode 1 or Mode 2) 50-51 LAMP AGE 52

APPENDIX 53-57

MAINTENANCE 53-55

TEMPERATURE WARNING INDICATOR 53 AIR FILTER CARE AND CLEANING 53 LAMP REPLACEMENT 54 CLEANING THE LENS 55

TROUBLESHOOTING 55-56 TECHNICAL SPECIFICATIONS 57

The multimedia projector that combines powerful and sophisticated features with easy-to-use, intuitive controls. Built-in multimedia features include audio, a palette of 16.77 million colors and active matrix liquid crystal display (LCD) technology. The projector is ideal for high-performance business, training and imaging applications that demand exceptional color quality.

The projector is compatible with many different types of personal computers and video devices, including:

● IBM-compatible computers, including laptops, up to 1600 x 1200 resolution.

● Apple Macintosh and PowerBook computers up to 1600 x 1200 resolution.

● Various VCRs, video disc players, video cameras, DVD players, satellite TV tuners or other AV equipment using any of the

worldwide video standards, including NTSC, NTSC4.43, PAL, PAL-M, PAL-N and SECAM.

The resolution of the projector's projected image is 1280 x 1024. The projector displays computer images just as they appear on your computer's monitor. Screen resolutions between 1280 x 1024 and 1600 x 1200 are compressed to 1280 x 1024. The projector cannot display screen resolutions above 1600 x 1200. If your computer's screen resolution is higher than 1600 x 1200, reset it to a lower resolution before you connect the projector.

This projector can detect display signals from most personal computers currently distributed. It is free from complicated adjustments to project picture images from PC.

Screen display can be selected among;

Computer mode --- True, Digital zoom (Expand, Compress, Panning) Video mode --- Regular (4:3), Wide (16:9)

MENU DISPLAY is displayed with; English, German, French, Italian, Spanish and Japanese.

The projector comes with the parts listed below. Check to find all the parts are included. If any parts are missing, contact an authorized dealer or service station.

● Owner's Manual. ● AC Power Cord.

● Wireless Remote Control Unit. ● Wireless/Wired Remote Control Unit.

● Remote Control Cable. ● Batteries for Remote Control Units.

● Graphic Accelerator Board and its Software. ● Digital Flat Panel Cable.

● VGA Cable. ● Mouse Cable for PS/2 port.

● Mouse Cable for serial port. ● Mouse Cable for ADB port.

● VGA/MAC Adapter. ● Protective Dust Cover

● Lens Cover.

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows is a trademarks or registered trademarks of Microsoft Corporation.

● Other trademarks are the property of their respective owners.

FEATURES AND DESIGN

INTRODUCTION

COMPATIBILITY

IMAGE RESOLUTION

UNPACKING THE PROJECTOR

TRADEMARKS

SCREEN MODE

AUTOMATIC MULTISCANNING SYSTEM

MULTILANGUAGE

EXHAUST VENT

CAUTION HOT AIR! Air blown from the exhaust vent is hot. Observe the following when handling your

projector or choosing a location to install it.

● Keep heat-sensitive objects away from the exhaust port.

● If you set the projector on top of a metallic surface, the surface will become hot because of the hot air exhaust. Be careful when handling.

● Do not touch the cabinet near to the exhaust vent area, and especially screws and metallic parts. These parts will become hot while the projector is used.

FRONT OF THE PROJECTOR

REAR OF THE PROJECTOR

200" 154"

26.9' (8.2 m)

600" 462"

80.7' (24.6 m)

40"

77"

115"

154"

231"

308"

462"

600"

100"

150"

200"

300"

400"

760 mm 760 mm

100" SCREEN

POSITIONING:

ROOM LIGHT

● This projector is basically designed to project on a flat projection surface.

● This projector can be focused from 4.9' (1.5 m) ~ 80.7' (24.6 m).

● Refer to the figure below as an example when positioning the projector to the screen.

The projector should be placed in a room with limited light. Picture quality will be directly affected by lightning conditions.

Minimum Zoom

Maximum Zoom

DISTANCE

Screen Size

Max. Zoom Min. Zoom

Distance

40"

4.9' (1.5 m)

100"

77"

13.1' (4.0 m)

150" 115"

20' (6.1 m)

300" 231"

40' (12.2 m)

400" 308"

53.8' (16.4 m)

THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. NEVER HANG THE PROJECTOR, OR FALL DOWN ON ITS SIDE. IT MAY RESULT IN FIRE HAZARD.

Picture tilt and projection angle can be adjusted by twisting ADJUSTABLE FEET. Projection angle can be adjusted up to 4 degrees by rotating Adjustable Feet.

MOVE THE PROJECTED IMAGE POSITION Adjust the projected image position (maximum 760mm

downward or upward on the 100" screen) by using lens shift function. (See page 33.)

DOWN

ADJUSTABLE FEET

SETTING-UP THE PROJECTOR

INSTALLATION

Use the carry handle when moving the projector. Replace the lens cover and rotate the adjustable feet fully clockwise.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

● Do not drop or give a shock to the projector, otherwise damage or malfunction may result.

● When carrying the projector, use a Sanyo recommended Carrying Case.

● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause

damage to the projector. To transport the projector through a courier or transport service, use a Sanyo recommended Case.

● For a carrying or transportation cases, contact a Sanyo authorized dealer.

This projector is equipped with a cooling fan to protect it from overheating. Pay attention to the following to ensure the ventilation and avoid a possible risk of fire and malfunction.

● Do not cover the vents with papers or other materials.

●

Keep the rear grill at least 3.3' (1m) away from any object.

● Make sure that there are no objects under the projector. An object under the projector may prevent the projector from taking the cooling air through the bottom vent.

VENTILATION

AIR INTAKE VENT (BOTTOM SIDE)

EXHAUST VENT (REAR SIDE)

MOVING THE PROJECTOR

INSTALLATION

Your projector uses nominal input voltages of 100-120 VAC. The projector automatically selects the correct input voltage. The projector is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure what type of power is supplied to your building.

Connect the AC power supply cord (supplied) to the projector. The socket-outlet must be near this equipment and must be easily accessible.

INSTALLATION

POWER REQUIREMENTS

Projector side (Female)

AC outlet side (Male)

SIDE OF THE PROJECTOR (CONNECT THE COMPUTER)

COMPUTER INPUT-1 TERMINAL (ANALOG HDB 15-PIN)

Used to connect a computer to the projector.

COMPUTER INPUT-1 TERMINAL (DIGITAL MDR 20-PIN)

Used to connect a computer to the projector.

COMPUTER INPUT-2 JACKS (BNC TYPE x 5)

Used to connect a computer to the projector.

MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN)

Used to connect a monitor to the projector.

COMPUTER AUDIO INPUT-1 JACKS (R and L)

Used to connect an audio output from the computer to the projector.

COMPUTER AUDIO INPUT-2 JACKS (R and L)

Used to connect an audio output from the computer to the projector.

AUDIO MONITOR OUTPUT JACKS (R and L)

Used to connect an audio input from audio equipment to the projector.

CONTROL PORT-1 CONNECTOR

Used to connect a mouse cable to the projector.

CONTROL PORT-2 CONNECTOR

Used to connect a mouse cable to the projector.

USB PORT-1 CONNECTOR

Used to connect a computer to the projector.

USB PORT-2 CONNECTOR

Used to connect a computer to the projector.

SERIAL PORT TERMINAL (DB9)

Used to connect a computer to the projector.

WIRED REMOTE JACK

When using the wired remote control, connect the remote cable to this jack.

USB 1 AUDIO 1

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

CONTROL PORT 2

DIGITAL

6 5

1 2

3 4 5

8 9

10 11

12 13

CONNECTING THE PROJECTOR

TERMINAL OF THE PROJECTOR

VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

(MONO)

AUDIO

VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

(MONO)

AUDIO

VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

AUDIO

VIDEO IN-1VIDEO IN-2MONITOR OUT

SIDE OF THE PROJECTOR (CONNECT THE VIDEO EQUIPMENT)

VIDEO INPUT JACKS-1 (BNC TYPE x 3)

Used to connect a video source to the projector.

S-VIDEO INPUT JACK-1

Used to connect a S-VHS video source to the projector.

AUDIO INPUT JACKS-1 (R and L)

Used to connect an audio source to the projector.

VIDEO INPUT JACKS-2 (BNC TYPE x 3)

Used to connect a video source to the projector.

S-VIDEO INPUT JACK-2

Used to connect a S-VHS video source to the projector.

14 15 16

17 18

AUDIO INPUT JACKS-2 (R and L)

Used to connect an audio source to the projector.

VIDEO MONITOR OUTPUT JACKS (BNC TYPE x 3)

Permits video connection to a monitor.

VIDEO MONITOR (S-VIDEO) OUTPUT JACK

Permits S-VHS video connection to a monitor.

AUDIO MONITOR OUTPUT JACKS (R and L)

Permits audio connection to a monitor.

19 20

CONNECTING THE PROJECTOR

––––––––

ADB –––––––– –––––––– –––––––– –––––––– –––––––– ––––––––

GND –––––––– –––––––– ––––––––

Serial Port

ADB Port

1 2 3 4 5 6 7 8

9 10 11 12

PS/2 Port

T x D –––––––– –––––––– –––––––– –––––––– ––––––––

READY

––––––––

GND –––––––– –––––––– ––––––––

––––––––

CLK

DATA –––––––– –––––––– –––––––– –––––––– ––––––––

GND –––––––– –––––––– ––––––––

CONNECTING THE COMPUTER

CONNECTING THE PROJECTOR

Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (provided). CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions.

For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

Digital output signal from the computer can be connected to the DIGITAL terminal (MDR 20-pin). When using this input, Graphic Accelerator Board designed for this projector should be installed into your computer and set-up the computer configuration following instruction included in the Graphic Accelerator Board package. Refer to DIGITAL INPUT CONNECTION on page 15 and 17.

Personal computers can be connected to the computer input (Red, Green, Blue, Horiz. Sync. and Vert. Sync.) on the projector.

● Connect the computer to these jacks using the BNC cables (not provided).

● Connect audio outputs from your computer to these jacks using the audio cable (not provided).

● When the computer is operated by projector's remote control unit, connect three different type of cables (provided)

between projector control port and computer mouse port or serial port.

■ CONTROL PORT

CONTROL PORT CABLE REMOVAL HINT

Disconnect control port cable with following steps.

1. Hold the portion (A) of the connector with one hand.

2. Pull the portion (B) arrow direction and remove connector.

CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (ANALOG HDB 15-PIN)

CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (DIGITAL MDR 20-PIN)

CONNECTING TO THE COMPUTER INPUT 2 JACKS (BNC x 5)

CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)

CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTORS (1 and 2)

COMPUTER TYPE

IBM Compatible computer with PS/2 mouse port. IBM Compatible computer with serial port. Apple Macintosh computer with ADB mouse port.

CABLE

Mouse Cable for PS/2 port. Mouse Cable for Serial port. Mouse Cable for ADB port.

These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1, Computer 2, Video 1 or Video 2). If you have selected program source Computer 2 the audio signal connected to the Computer 2 audio input jack will be available at the audio monitor output jacks. Use RCA type audio for connection.

● If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right and left jacks.

● If the audio input of the audio equipment is monaural, connect it to the left jack.

Vcc

- Data

+ Data

Ground

1 2 3 4

This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source ("Video 1" or "Video 2") is selected, this terminal outputs Computer 1 input information.

An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the monitor to this terminal using the VGA cable (not provided).

––––––––

R x D T x D

––––––––

Ground –––––––– –––––––– –––––––– ––––––––

1 2 3 4 5 6 7 8 9

■ SERIAL PORT DB9-PIN

TERMINAL

■ USB PORT

Pin No./Signal

1 Red input 2 Green input 3 Blue input 4 Sense 2 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue)

Pin No./Signal

9 Non Connect 10 Ground (Vert. sync.) 11 Sense 0 12 Sense 1 13 Horiz. sync 14 Vert. sync 15 Reserved

HDB 15-PIN TERMINAL

CONNECTING THE PROJECTOR

CONNECTING TO THE MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN)

CONNECTING TO THE AUDIO MONITOR OUTPUT (VARIABLE) JACKS

CONNECTING TO THE SERIAL PORT (DB 9-PIN) TERMINAL

CONNECTING TO THE USB PORT CONNECTORS (1 and 2)

● If you control the projector by computer, you must connect a cable (not provided) from your computer to this terminal.

This Projector is designed for connecting with USB Port of the computer or peripheral equipment that is to be standard.

54321

109876

15 14 13 12 11

12345

6789

USB 1 AUDIO 1

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

CONTROL PORT 2

DIGITAL

CONNECTING THE PROJECTOR

USB 1 AUDIO 1

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

CONTROL PORT 2

DIGITAL

COMPUTER

MONITOR CABLE (NOT PROVIDED)

SERIAL PORT INPUT

AUDIO CABLE (NOT PROVIDED)

COMPUTER AUDIO INPUT 1

CONTROL PORT OUTPUT 1

MOUSE CABLE FOR PS/2 PORT (PROVIDED)

MOUSE CABLE FOR SERIAL PORT (PROVIDED)

PS/2 PORT INPUT

L R

R L

Speaker (L)

Speaker (R)

Amp.

R L

AUDIO INPUT

SPEAKER OUT

COMPUTER AUDIO OUTPUT

SERIAL PORT CABLE (NOT PROVIDED)

SERIAL PORT OUTPUT

COMPUTER AUDIO OUTPUT

COMPUTER INPUT 1 (DIGITAL)

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

(DIGITAL INPUT CONNECTION)

DIGITAL FLAT PANEL CABLE (PROVIDED)

NOTE:

Before using with digital connection, install (Plug in) Graphic Accelerator Board (included within projector) into PCI bus slot of the computer and set up the computer following instructions in the Graphic Accelerator Board package.

GRAPHIC ACCELERATOR BOARD

DIGITAL OUTPUT

ANALOG OUTPUT

INSTALL (PLUG) INTO PCI BUS SLOT

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

USB 1 AUDIO 1

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

CONTROL PORT 2

DIGITAL

SERIAL PORT OUTPUT

COMPUTER

COMPUTER OUTPUT (DB15-PIN TYPE)

SERIAL PORT INPUT

PS/2 PORT INPUT

AUDIO CABLE (NOT PROVIDED)

VGA CABLE (PROVIDED)

MOUSE CABLE FOR PS/2 PORT (PROVIDED)

MOUSE CABLE FOR SERIAL PORT (PROVIDED)

R L

Speaker (L)

Speaker (R)

Amp.

AUDIO INPUT

SPEAKER OUT

COMPUTER AUDIO OUTPUT

COMPUTER AUDIO INPUT 1

CONTROL PORT OUTPUT 1

COMPUTER AUDIO OUTPUT

SERIAL PORT CABLE (NOT PROVIDED)

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER

COMPUTER INPUT 1 (ANALOG)

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

USB 1 AUDIO 1

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

CONTROL PORT 2

DIGITAL

123456

CONNECTING THE PROJECTOR

CONTROL PORT OUTPUT 1 or 2

COMPUTER

MONITOR CABLE (NOT PROVIDED)

COMPUTER OUTPUT (BNC TYPE x 5)

BNC CABLE x 5 (NOT PROVIDED)

COMPUTER OUTPUT

COMPUTER AUDIO OUTPUT1 or 2

AUDIO CABLE (NOT PROVIDED)

MOUSE CABLE FOR ADB PORT (PROVIDED)

COMPUTER INPUT 2

VGA/MAC ADAPTER (PROVIDED)

R L

Speaker (L)

Speaker (R)

Amp.

AUDIO INPUT

SPEAKER OUT

COMPUTER AUDIO OUTPUT

SERIAL PORT CABLE (NOT PROVIDED)

SERIAL PORT OUTPUT

COMPUTER INPUT 1 (ANALOG)

CONNECTING A MACINTOSH DESKTOP COMPUTER

VGA CABLE (PROVIDED)

COMPUTER AUDIO OUTPUT

MONITOR OUTPUT

OFF

VGA/MAC ADAPTER

SW1 ~ SW6

Set the dip switches as shown in the table below depending on the RESOLUTION MODE that you want to use before you turn on the projector and computer.

ADB PORT INPUT

SW1

ON OFF OFF

RESOLUTION MODE 13" MODE (640

480)

16" MODE (832

624)

19" MODE (1024

768)

21" MODE (1152

870)

SW6

OFF OFF OFF OFF

SW5 OFF OFF OFF OFF

SW4

OFF

SW3

OFF OFF

ON ON

SW2

ON ON ON ON

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

+ 40 hidden pages