Configuration and ConnectionsSanyo Installation
SYSTEM 4
xixi
xi
xixi
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: SANYO
Included Communications Adapter(s):
Quantity Part Number Description
1 26-467-01 ADP, UNV, “A”
1 26-489-01 ADP, UNV, “J”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURA TION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF Y OUR PROJECT OR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE Y OUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR: SANYO PLC
CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM
AS 1 2 3 4 CABLE ADAPTER
✔ PLC off on off on 0 0 1 E 0 J15 26-467-01
✔ PLC 8810 off on off on 0 0 1 E 0 J15 26-489-01
PLC XP10 off on off on 0 0 1 E 0 J15 26-489-01
PLC XP30 off on off on 0 1 1 E 0 J15 26-489-01
Extron • System 4
xixi
xi
Switcher Series • User’s Manual • P/N 68-402-02 Rev. E
xixi
Page 1
Sanyo Installation Configuration and Connections
y
)
Connecting System 4
[System 4NE model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(Note: Information depends on
stem 4NE
S
(See note.)
setup.
}
xixi
xi to Sanyo PLC
xixi
If the System 4xi is already configured for a Sanyo PLC projector, go to step 4.
If it is not set up correctly, it will be necessary to change switch settings on the
System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct
configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi
is already set up for the Sanyo PLC. Apply power to the System 4xi and do the
following:
a. Press
b. Press
to display the MENU SELECT on the LCD screen.
or to step to Menu 8.
c. Press to select this menu.
d. Press or to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the
following information:
PRJ = SANYO
PRJ BAUD = 19200
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the
System 4xi User’s Manual
to remove the
System 4xi cover. Then go to page 2-4 and refer to the configuration below to
set up the Main Controller board. Continue with Step 3 (below) when the
configuration is correct.
Config Projector SW1: 1-2-3-4 SW2 SW3 SW4 SW5 SW6 Prj Cable Comm
as Adapter
✔ Sanyo PLC off-on-off-on 0 0 1 E 0 J15 26-467-01
or 26-489-01
SW3
SW2
SW4
J15
SW1
4
SW5
3
2
1
ON
Extron • System 4
3. Double-check your work and be sure the System 4xi cover is on securely.
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
xixi
xi
Switcher Series • User’s Manual • P/N 68-402-02 Rev. E
xixi
Page 2
5. The Sanyo PLC Comm Adapter (26-467-01) has a 9-pin male connector that
accommodates the Comm Extension cable. The other end of the Comm Adapter
plugs into the projector’s RS-232C port.
6. Plug the 15-pin HD connector of the Projector Communications Extension cable
into the PJ Comm port on the System 4xi.
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV
cable onto the System 4xi output and those on the other end onto the matching
BNCs on the Sanyo PLC connector panel.
System 4xi Series – Sanyo PLC Projector Connections
Use the illustration below as a guide when connecting the System 4xi to a Sanyo
PLC Projector. Refer to Sanyo documentation to continue the installation.
See Special Note below
C/Cb(B-Y) Cr(R-Y) S-VIDEO
AUDIO 1VIDEO/Y
RL
Configuration and ConnectionsSanyo Installation
R
CONTROL PORT 1USB 1
AUDIO 1
RL
GBHV
C/Cb(B-Y) Cr(R-Y)
C/Cb(B-Y) Cr(R-Y)
S-VIDEO
S-VIDEO
AUDIO 1VIDEO/Y
RL
AUDIO 1VIDEO/Y
RL
USB 2
ComAdapter
26-467-01 "A"
or 26-489-01 "J"
CONTROL PORT 2
SERIAL PORTAC JACK
A
AUDIO 2
RL
AUDIO OUT
RL
9-Pin Male
9-Pin Male
ANALOG RGB
ANALOG RGB
9-Pin Female
RGBHV 5 BNC
15-Pin
Male
INPUT 1
H/HV V
R/C G/Y B
INPUT 2
H/HV V
AUDIO AUDIO AUDIO AUDIO AUDIO
R/C G/Y B
INPUT 3
H/HV V
R/C G/Y B
INPUT 4
H/HV V
PJ COMM
RS 232
OUTPUT
H/HV
V
R/C G/Y BR/C G/Y B
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4xi. See page 2-5 for cabling guidelines.
Special Note: _____ Certain PLC projectors may not come equipped with a 9-pin serial port
connector. In those situations, the Com adapter must be connected to Control
Port 2 using the projector’s special DIN to 9-pin serial adapter, as illustrated
below.
To projector's Control Port 2
Extron • System 4
9-Pin Female
9-Pin Male
9-Pin Male
9-Pin Female
A
Sanyo DIN to 9-pin adapter
xixi
xi
Switcher Series • User’s Manual • P/N 68-402-02 Rev. E
xixi
Extron Com Adapter
26-467-01 "A"
or 26-489-01 "J"
To switcher's Projector Control port
Page 3
Loading...