Sanyo LA7685J Specifications

Page 1
Ordering number: EN 5153
Monolithic Linear IC
LA7685J
PAL/NTSC Single-chip Color Television
Signal Processing Circuit
Overview
The LA7685J is a single-chip IC (with VIF, SIF, video, chroma, and deflection circuits built in) for use in PAL or NTSC television sets. Because the PLL+ splitting method is used in the VIF circuit, the LA7685J is suited for use in top-of-the-line small and mid-size television sets. In addition, when used in combination with the LA7640N SECAM chroma IC, the LA7685J can be used in a PAL/NTSC/SECAM multisystem set.
Features
[VIF Block]
.
PLL+ splitting (for excellent image and sound quality)
.
High-gain VIF amplifier
.
High-speed AGC
.
APC time constant switch built in
[SIF Block]
.
Simultaneous audio IN/OUT
.
Video/audio simultaneous muting, or audio only muting also possible
.
1st amplifier with AGC function
[AV Switching Block]
.
INT/EXT AV switch
[Video Block]
.
Black extension
.
DC restoration
.
Delay line built in
.
Wide band: 9 MHz (with delay line shorted)
.
Built-in double differential circuits that also enable soft tone
.
Supports S input (for VCRs)
.
DC transmission amount can be varied (externally adjustable)
[Deflection Block]
.
Adjustment-free horizontal and vertical sync
.
Excellent anti-noise characteristics due to adoption of duplex AFC
.
Vertical sync sensitivity can be adjusted externally
.
Constant vertical size with no signal (constant for 60/50 Hz)
.
Highly stable image during copy guard tape playback (macrovision tapes, etc.)
.
Excellent stability against VCR skew distortion
Package Dimensions
unit : mm
3071-DIP64S
Delay line Video EXT, audio EXT Switch conditions
OFF IN D OFF EXT C
ON EXT B ON IN A
[OSD Block]
.
Three RGB inputs
.
RGB linear amplifier (–6 dB input: 2 V to 5 V)
.
First blanking (also used for B input)
[Chroma Block]
.
ACC filter, carrier filter built in
.
Ident detection output
.
Killer detection output
Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
[LA7685J]
3364
57.2
0.95 0.48 1.78 1.01
321
SANYO : DIP64S
63095HA(II) No.5153-1/10
19.05
4.00.51min
16.8
5.0max
3.2
0.25
Page 2
LA7685J
Specifications
Maximum Ratings atTa=25°C
Parameter Symbol Conditions Ratings Unit
V
max 11 V
Maximum supply voltage
Maximum supply current I Allowable power dissipation Pd max Ta % 60°C 1.53 W Operating temperature Topr –10 to +65 Storage temperature Tstg –55 to +150
Circuit current
FBP input current
Operating Conditions atTa=25°C
Parameter Symbol Conditions Ratings Unit
Recommended supply voltage
Recommended supply current I
Operating supply voltage range
Operating supply current range I
2
V
max 11 V
12
max 16 mA
32
I
56
I
6
I
max Peak current 5 mA
33
I
max Peak current 10 mA
27
V
2
V
12
32
V
op 8 to 9.5 V
2
V
op 8 to 9.5 V
12
op 10 to 16 mA
32
–6 mA –3 mA
9V 9V
13 mA
C
°
C
°
Allowable power dissipation, Pd max — W
Pd max — Ta
Ambient temperature, Ta —°C
No.5153-2/10
Page 3
LA7685J
Electrical Characteristics atTa=25°C, VCC=V2=V12=9V,ICC=I32=13mA
Parameter Symbol Conditions min typ max Unit [Circuit Voltage, Current] Horizontal supply voltage V Supply current I
32
2+12
[VIF Block] fp = 38.9 MHz Video output voltage
with no signal AFT output voltage
with no signal Maximum RF AGC voltage V Minimum RF AGC voltage V
V
56
V
60 5H
5L
Input sensitivity Vi AGC range GR Maximum input (V
Maximum allowable input Vi max Video output is +1 dB. VIF input level 97 104 dBµ Video output amplitude V
O56
Differential gain DG Vi = 80 dBµ, 87.5 %, VIDEO MOD 3.0 10 % Differential phase DP Vi = 80 dBµ, 87.5 %, VIDEO MOD 1.0 10 deg
Video S/N S/N Sync signal tip level V
Frequency characteristics f
1.07 kHz beat level I Maximum AFT output voltage V Minimum AFT output voltage V
56 TIP
C
1.07 60H
60L
AFT detection sensitivity Sf CW = 80 dBµ, frequency change 50 80 110 AFT defeat start voltage V Black noise threshold level V APC pull-in range (U) f APC pull-in range (L) f
VCO maximum variable range
AFT SW
BTH PU
PL
f
f
VCO control sensitivity β No signal 1.3 2.5 5.3 [AVSW Block] Image output DC voltage V Internal image input voltage V External image input voltage V
50 54 52
External audio input voltage V [1st SIF Block]
5.5 MHz conversion gain VG Vi = 70 dBµ, 33.4 MHz 21 26 31 dB Output level V Maximum input level V [SIF ATT Block] f
5.5 MHz
S
59
max fS= 33.4 MHz 96 101 dBµ
11
SIF limiting voltage Vi lim SIF input when detection output is –3 dB. 40 47 dBµ FM detection output voltage V
O1
FM dectection output distortion THD Vi = 100 dBµ, f = ±30 kHz 0.4 1.0 % AM rejection ratio AMR Vi = 100 dBµ, ATT voltage gain G
Maximum attenuation of electronic volume control
AF
ATT Vi=2Vrms, f = 400 Hz 70 80 dB
[Video Block] Black extension threshold BS Maximum black extension gain BSmax APL variable, input 0.5 Vp-p –30 –22 –13 IRE
Soft video tone varlable range Soft
VCC=9V,ICC= 13 mA 7.1 7.6 8.1 V VCC=9V,ICC= 13 mA, IFAGC=4V 102 120 138 mA
No signal 4.3 4.7 5.1 V
No signal 3.0 4.5 6.0 V CW = 85 dBµ, RF AGC VR = min 7.6 8.0 8.3 V
CW = 85 dBµ, RF AGC VR = max 0 0.01 0.3 V Video output is 0.8 Vp-p (40 % MOD), VIF input
level
= 0.8 Vp-p) – Input sensitivity 54 62 dB
0
33 39 45 dBµ
Vi = 80 dBµ, AM = 78 % MOD 1.7 2.0 2.3 Vp-p
Vi = 80 dBµ, 20 log
1.46 (Vp-p)
Noise (Vrms)
47 54 dB
CW = 80 dBµ 2.1 2.4 2.7 V Frequency when video output is –3 dB 6.5 8.0 MHz V4.43 MHz/V1.07 MHz, Vi = 80 dBµ 35 50 dB CW = 80 dBµ, frequency change 7.6 8.0 8.4 V CW = 80 dBµ, frequency change 0.6 1.0 1.4 V
Measure with sweep signal 0.5 1.0 V Measure with sweep signal 1.1 1.4 1.7 V CW = 80 dBµ, fp = 34 MHz to 44 MHz 0.8 1.7 MHz CW = 80 dBµ, fp = 53 MHZ to 64 MHz –2 –1 MHz No signal 0.9 1.7 MHz
U
No signal –2 –1 MHz
L
No signal 3.0 3.4 3.8 V No signal 4.4 4.8 5.2 V No signal 4.4 4.8 5.2 V No signal 5.2 5.6 6.0 V
4
Vi = 10 mV, 33.4 MHz 210 320 480 mVp-p
Vi = 100 dBµ, f = ± 30kHz 390 500 630 mVrms
FM : f = ±30 kHz
AM:30%
40 60 dB
Vi=1Vrms, f = 400 Hz –1 0 1 dB
APL variable, input 0.5 Vp-p 40 50 60 IRE
TH
f = 2 MHz, 100 mVp-p Video tone V
:4V0V
R
–6 –4 –2 dB
Continued on next page.
mV/kHz
kHz/mV
No.5153-3/10
Page 4
LA7685J
Continued from preceding page.
Parameter Symbol Conditions min typ max Unit
Sharp video tone variable range
Video voltage gain AC switch 9 V
Video voltage gain AV switch 0 V
Contrast control center C
Sharp
GV
GV
CEN
Contrast control variable range C
BR
Bright control
BR
CEN
BR
Frequency characteristics D.L.ON
DC transmission amount R Delay line delay amount
(one level) Delay line delay amount
(two levels)
f
T
T
V0V
DC
DL1
DL2
[Chroma Block PAL/NTSC Common] Color control color residue E
min Color VR: 0 V, contrast VR: 9 V 30 mVp-p
C
Color contrast variable range C Demodulation output DC
voltage Demodulation output DC
difference voltage Demodulation output
carrier leakage
APC pull-in range F
Kill output V
V
C-Y
V
C-Y
Ecar No signal, killer off, color V
APC
KiOUT
[Chroma Block PAL] Color control center E
ACC amplitude characteristics
CCEN
ACC ACC
B/Rp 1.10 1.35 1.60
Demodulation output ratio
G/Rp B-Y no signal –0.56 –0.51 –0.46
G/Bp R-Y no signal –0.21 –0.19 –0.17 Demodulation angle RBp 85 90 95 deg Maximum chroma output Ech Color V Maximum demodulation output E Killer operating point E
max Color VR: 9 V, contrast VR: 9 V 3.6 4.2 Vp-p
C KONP
PAL output 0.3 V [Chroma Block NTSC] Color control center E
ACC amplitude characteristics
ACC phase characteristics Tint center T
CEN
ACC ACC ACC ACC
CEN
Tint variable range T
Demodulation output ratio
Demodulation angle Maximum demodulation output E
Kill operation point E NTSC/SECAM output E
R/B
G/B
RB GB
maxNColor VR: 9 V, contrast VR: 9 V 3.5 4.1 Vp-p
C
KONN KONN
f = 2 MHz, 100 mVp-p, video tone V
:4V9 V, contrast VR:6V
R
f = 100 kHz, 100 mVp-p, contrast
9V
V
: 9 V, video tone VR:4V
R
71013dB
15 18 21 dB
f = 100 kHz, 100 mVp-p, contrast
0V
V
:0V,
R
video tone V
R
:4V
15 18 21 dB
f = 100 kHz, 100 mVp-p, contrast VR: 6 V 0.35 0.44 0.53 Vp-p Contrast VR:3V9 V 22 24 26 dB
V
Bright VR: 2.0 V 5.5 6.5 7.5 V
H
Bright VR: 5.25 V 2.3 2.8 3.3 V Bright VR: 7.5 V 0.5 1.5 V
L
Contrast VR: 6 V, video tone VR: 4 V, 3 dB down 4.5 6 MHz Input : STAIR STEP signal, 200 mVp-p 88 93 % Input : WHITE 100 % 300 350 400 ns
Input : WHITE 100 % 370 420 470 ns
Color VR: B-Y = 2.5 Vp-p, contrast VR:3V9 V 18.5 20 21.5 dB
C
Burst signal only, color VR: 0 V 4.8 5.3 5.8 V
Burst signal only, color VR: 0 V –300 0 +300 mV
: 0 V 0.03 Vp-p
R
±500 Hz
Color VR: 4.5 V, contrast VR: 6 V 1.5 2.0 2.5 Vp-p +6 dB –3 0 +3 dB
M1P
–20 dB –5 –1 +1 dB
M2P
: 9 V, contrast VR: 9 V 1.5 2.0 2.5 Vp-p
R
–37 –33 –29 dB
Color VR: 4.5 V, contrast VR: 6 V 1.4 1.9 2.4 Vp-p +6 dB –3 0 +3 dB
M1N
–20 dB –3 0 +3 dB
M2N
+6 dB –3 0 +3 deg
P1N
–20 dB –7 0 +7 deg
P2N
Tint VR= 4.5 V, color VR: 4.5 V, contrast VR: 6 V –12 0 +12 deg Tint V
:0V4.5 V 9V,
R
color V
N
N N N
: 4.5 V, contrast VR:6V
R
±35 deg
0.82 0.91 0.99
0.18 0.25 0.32 99 105 111 deg
–130 –120 –110 deg
–39 –35 –31 dB
1.4 1.9 2.4 V
Continued on next page.
0.35 V
No.5153-4/10
Page 5
LA7685J
Continued from preceding page.
Parameter Symbol Conditions min typ max Unit [Deflection Block] Sync separation input voltage V
Vertical free-running frequency
Vertical sync maximum period
Vertical sync minimum period Vertical blanking pulse peak
value Vertical blanking pulse width Vertical output pulse width P
Vertical output voltage
Vertical external trigger load resistance
Vertical automatic sync stop voltage
Vertical output pulse start V voltage
CC
Horizontal free-running frequency deviation
Dependence of horizontal free-running frequency on V
CC
Horizontal pull-in range f Horizontal output pulse start
V
voltage
CC
AFC II FBP peak value FBP
SDC
T
free
V
T
free
V
T
max
V
T
max
V
T
min
V
T
min
V
V
HVBL
P
WBLK50
P
WBLK60
WVOUT
V
OUT H
V
OUT M
V
OUT L
R
TR
V
SAS
S
VV
f
f
HVCC
HPULL
S
HV
50 60
Horizontal sync signal only 356.5 357 357.5 H
50
Horizontal sync signal only 296.5 297 297.5 H
60 50 60
Deviaton from 15.680 kHz –100 0 +100 Hz
H
V25 = 6.5 V, reference value 2 Hz Deviation from 15.680 kHz ±450 Hz
H
VCR switch input voltage VCR 0.7 0.9 V Horizontal output pulse width P
Horizontal output pulse phase
Burst gate pulse width P Burst gate pulse phase Td Horizontal sync detection
threshold level 50/60 output voltage
50/60 input voltage X ray protection circuit operation
input voltage Sandcastle H.BLK peak value V Sandcastle BGP peak value V Sandcastle BP peak value V Sandcastle BGP width P Sandcastle BGP phase Td Sandcastle field ID width P Sandcastle H.BLK width 50 P Sandcastle H.BLK width 60 P
WHOUT
H
PF
H
PCEN
H
PR
WBGP
BGP
Hcoin 4.2 4.5 4.8 V
V
50
V
60
Vin
50
Vin
60
V
HD
H SHBL H SBGP
H SBP
W SBGP
SBGP
W SFID W SHBL50 W SHBL60
6.0 6.3 6.6 V
312.0 312.5 313.0 H
262.0 262.5 263.0 H
268.5 269 269.5 H
224.5 225 225.5 H
7.0 7.5 V
21.0 21.5 22.0 H
17.0 17.5 18.0 H
8.0 8.5 9.0 H
5.7 6 6.3 V
4.3 4.6 4.9 V
0.3 V
2.5 3.6 k
1.2 1.4 1.6 V
4V
4.8 5.5 V
4.1 4.6 5.1 V
21.8 23.8 25.8 µs 12 µs
3.4 4.4 5.4 µs 0µs
2.7 3.7 4.7 µs
0.2 0.6 1.2 µs
0.5 0.7 V
4.0 4.7 V
0.5 V
7.2 V
0.64 0.74 0.84 V
3.7 4.0 4.3 V
7.7 8.0 8.3 V
5.7 6.0 6.3 V
1.4 1.9 2.4 µs
1.7 2.2 2.7 µs
11.5 12 12.5 H
11.0 12.0 13.0 µs
10.0 11.0 12.0 µs
Continued on next page.
No.5153-5/10
Page 6
Continued from preceding page.
Parameter Symbol Conditions min typ max Unit [OSD Block] Blanking pulse threshold level TH –Y OUT DC voltage
(OSD mode)
R.G.B. –IN threshold level
R.G.B. –Y OUT DC voltage (3 V)
R.G.B. –Y OUT DC voltage (4 V)
R.G.B. –Y OUT DC voltage (5 V)
TH
V
V V
V V
V
V
TH
BL
-Y
R3V G3V
B3V R4V G4V
B4V R5V G5V
B5V
LA7685J
C-IN : color bar, B-IN : variable 0.6 0.9 1.2 V B-IN : 1.5 V 2.4 2.7 3.0 V R-IN : variable, B-IN : 1.5 V
R
G-IN : variable, B-IN : 1.5 V
G
B-IN : variable
B
R,G,B-IN:3V 5.2 5.5 5.8 VV
R,G,B-IN:4V 5.8 6.1 6.4 VV
R,G,B-IN:5V 6.3 6.6 6.9 VV
1.4 1.7 2.0 VTH
No.5153-6/10
Page 7
Block Diagram
LA7685J
No.5153-7/10
Page 8
Sample Application Circuit
LA7685J
No.5153-8/10
Page 9
LA7685J
LA7685J and LA7640N Connection Diagram (Reference)
Unit (resistance: , capacitance: F)
No.5153-9/10
Page 10
LA7685J
Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.
Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of June, 1995. Specifications and information herein are subject to change without notice.
PS No.5153-10/10
Loading...