Page 1
Ordering number: EN 4981
Monolithic Linear IC
LA6524
4-output Power Driver
Overview
The LA6524 is a 4-output power driver developed for use in
consumer and industrial equipment.
Functions
.
Four buffer amp circuits on chip
.
High output current (Io max = 0.5 A)
.
Includes current limiter
.
Broad operating voltage range (±2 to +12 V)
.
Single power supply operation possible (4 to 24 V)
.
Thermal shutdown circuit built-in.
Specifications
Package Dimensions
unit : mm
3046B-SIP10F
[LA6524]
25.5
24.0
3.6
14.0
16.7max
8.4
3.5
1.6min
1.32
2.54
0.5
101
1.3
SANYO : SIP10F
Maximum Ratings atTa=25°C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage V
Input voltage V
Allowable power dissipation Pd max When using Al heat sink ( 50 x 50 x 1.5 mm
Operating temperature Topr –20 to +75
Storage temperature Tstg –40 to +125
CC/VEE
IN
3
) 2.0 W
3.6
0.45
1.6
±15 V
±14 V
C
°
C
°
Operating Characteristics atTa=25°C, VCC/VEE= ±10 V
Parameter Symbol
Current drain with no load I
Input offset voltage V
Input bias current I
Input voltage range V
Maximum output voltage V
Slew rate SR
Limiter current (built-in type) I
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
CC
SC
IO
B
ID
O
RS% 10 kΩ 27mV
RL=33Ω ±8 V
R
L
C1 = 0.1 µF
Conditions
=33Ω,R1=2.2Ω,
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
min typ max Unit
10 30 mA
50 500 nA
–9 +8 V
0.15 V/µs
0.5 A
51695HA(II) No.4981-1/4
Page 2
Pin Assignment
Block Diagram
LA6524
Sample Application Circuit
Load
2.2[Ω]
0.1[µF] (Film)
No.4981-2/4
Page 3
Test Circuit
LA6524
short wave
Oscilloscope
Al heat sink
Tightening torque: 4 kg
Coated with silicone grease
.
cm
When VORL=33Ω,
When I
SCRL
C/W
°
-
f
=8Ω
Al heat sink, t = 1.5 mm
Allowable power dissipation, Pd max - W
Storage temperature, Ta -°C
Thermal resistance of heat sink, θ
Area of heat sink, S
-cm
f
2
No.4981-3/4
Page 4
LA6524
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification”
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of May, 1995. Specifications and information herein are subject to
change without notice.
PS No.4981-4/4
Loading...