Sanyo IDC-1000ZE, IDC-1000ZU, IDC-1000ZEX User Manual

INSTRUCTION MANUAL

Digital disk camera

IDC-1000ZEX IDC-1000ZE IDC-1000ZU

This manual explains how to safely operate the IDC-1000ZEX, IDC-1000ZE, and IDC-1000ZU.

Any information regarding only one of these products will be labeled as such.

Please read these instructions carefully before using the digital disk camera. Make sure to read and understand the section USING YOUR

DIGITAL DISK CAMERA SAFELY AND CORRECTLY from page 5 to 17. Keep this manual in a safe place for later reference.

Caution for laser

Do not open covers and do not repair yourself. Refer servicing to qualified personnel. This product utilizes a laser. The use, adjustment, or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Laser

Type : Semiconductor laser AlGanP Output power : 3.5 mW (read-average),

5.85 mW (write-average) Beam divergence : 45.5 degrees (objective lens emission) Wavelength : 655 to 666 nm (at 20 to 25°C)

English

Warning

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

FOR AMERICAN USERS

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy; and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the device and receiver. – Connect the device to an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/television technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

Declaration of Conformity

Model Number : IDC-1000ZU Trade Name : SANYO Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 Telephone No. : (818) 998-7322 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

FOR CANADIAN USERS

œ This Class B digital apparatus complies with Canadian ICES-003.

English

BEFORE READING THE MANUAL

PowerPC is a registered trademark of International Business Machines Corporation in the United States.

Apple, Macintosh, and QuickTime are registered trademarks of Apple Computer Inc. in the United States.

Windows and Windows NT are registered trademarks in the United States and other countries of Microsoft Corporation in the United States.

Agfa PhotoGenie is a registered trademark in Germany and other countries of Agfa-Gevaert AG in Germany.

The iD PHOTO logo mark is a registered trademark. All other company and product names are registered trademarks or trademarks of their

respective owners.

Regarding the data storage media

œ This digital disk camera uses an iD PHOTO disk for data storage. In this manual, the iD

PHOTO disk is referred to as “disk.”

Caution

œ It is forbidden to copy this manual, whole or in part, without prior written permission. œ All images and illustrations given in this manual are for explanation purposes and may differ

slightly from that of the actual product. Also, actual specifications are subject to change without prior notice and therefore may differ from the contents of this manual.

œ Sanyo Electric shall not be held responsible for any problems resulting from the use of this

digital disk camera.

œ Sanyo Electric declines all responsibility for damages due to improper use of the digital disk

camera, failure to adhere to the instructions given in this manual, or repairs or changes done by those other than a technician authorized by the manufacturer.

œ Sanyo Electric shall not be held responsible for any damage caused by optional devices or

consumable items used with the digital disk camera other than those supplied with the digital disk camera or those specified by Sanyo Electric.

œ Sanyo Electric shall not be held responsible for any losses or loss of revenue resulting from the

loss of data caused by the malfunction, or the repairing of a malfunction, of the digital disk camera.

œ The images captured with this digital disk camera will differ in quality from pictures taken with a

standard film camera.

Symbols used in this manual

CAUTION Points that require special attention. NOTE Points giving some extended instructions or operations that require special care. HINT Points that may prove useful when using the digital disk camera. HELP In case of problem, this may help in certain situations.

9 h Explanations regarding sequential shots. g k Explanations regarding audio recordings.

English

Explanations regarding still images.

Explanations regarding video clips.

CONTENTS

USING YOUR DIGITAL DISK CAMERA SAFELY AND CORRECTLY. . . . . . . . . . . . . . . . . . 5

Preparation

CHECKING THE INCLUDED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

PARTS NAMES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

INSERTING AND EJECTING THE DISK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

TURNING THE POWER ON AND OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

SETTING UP AND USING THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

CHECKING THE BATTERY PACK AND DISK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

SETTING THE DATE AND TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Recording and playback

BASIC SHOOTING AND PLAYBACK OPERATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

PLAYING BACK FILES ON A TELEVISION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Shooting functions

USING THE VARIOUS SHOOTING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

MANUAL MODE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Speciality shooting

INTERVAL SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

ANIMATION SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Camera settings

CUSTOM SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

SETTING THE REMAINING DISK SPACE DISPLAY FORMAT. . . . . . . . . . . . . . . . . . . . . 125

Editing

ADDING A VOICE MEMO TO AN IMAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

ADDING AN IMAGE TO ANOTHER IMAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

ENLARGING (ZOOMING IN) THE IMAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

EDITING VIDEO CLIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

PROGRAMMED PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

Disk operations

HANDLING DATA STORED ON THE DISK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

FORMATTING THE DISK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

Appendices

USING WITH A COMPUTER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

English

USING YOUR DIGITAL DISK CAMERA SAFELY AND CORRECTLY

SAFETY PRECAUTIONS

The following safety precautions are to ensure the safe and correct use of your digital disk camera and prevent injury to the user and others, and property damage. Be sure to read carefully all the precautions listed here before using your digital disk camera.

LI-ION BATTERY PACK (UR-121)

DANGER

Your digital disk camera uses a Li-ion battery pack (part number UR-121).

■ If you notice leaking electrolyte, discoloration, deformation, damaged portions, strange odors, or other abnormality, immediately remove from the device, stop use, and move away from any open flames

œ If you continue use under these conditions, it may cause a fire, rupturing of the battery pack,

eruption of electrolyte, or smoking.

œ If electrolyte is leaking and a flame or spark occurs nearby, the electrolyte in the battery pack

may ignite causing a fire, rupturing of the battery pack, eruption of electrolyte, or smoking.

■ Do not disassemble or modify

œ The battery pack is equipped with built-in safety mechanisms and protection

devices to prevent dangerous accidents. Disassembling, modifying, soldering, or other similar operations on the battery pack may render these mechanisms or devices dysfunctional and cause a fire, rupturing of the battery pack, or an eruption or leakage of electrolyte.

■ Do not short the positive (+) and negative (–) poles with a metal pin or other object and do not carry or store together with a metal necklace or other object

œ If the poles are shorted, a large amount of current will flow, which may cause a fire, rupturing of

the battery pack, eruption or leakage of electrolyte, or overheating. Also, the metal object shorting the poles together will become excessively hot. When carrying or storing the battery pack, always place it in the supplied protective cover.

■ Do not place in a fire or expose to excessive heat

œ The insulation may melt or the gas venting valves and safety mechanisms may fail

allowing the electrolyte to ignite and cause a fire or rupturing of the battery pack.

■ Do not drop or subject to strong impacts

œ Strong impacts may damage the safety mechanisms and protective devices and

cause a chemical reaction within the battery pack that may cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

■ Do not submerge in water or wet the terminals

œ This will cause corrosion and damage the safety mechanisms and protective

devices leading to a chemical reaction within the battery pack that may cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

English

■ Cautions concerning the locations of use and storage

œ Ambient temperature during use or charging: 0 to 40° C

Do not use, recharge, store, or leave near an open flame, in a car under the hot sun, or in any other hot location (60°C or higher).

Extreme heat will damage the safety mechanisms and protective devices and cause a chemical reaction within the battery pack that may cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating. If the safety mechanisms and protective devices are damaged, the battery pack will become unusable.

If subject to extremely hot or cold conditions, the capacity of the battery pack will decrease and its usable life will be shortened. Use in ambient temperatures of 20±5°C is recommended. Ambient temperatures below 10°C will cause the operation time to become drastically shortened.

œ Ambient temperature during storage: – 20 to 30°C

When storing the battery pack, remove it from the device, insert it into its protective cover, and store it in a location between –20°C and 30°C.

œ Ambient humidity: 45 to 85% RH

■ Only recharge using the supplied NC-LSC04WSA AC adapter/charger

œ If recharged using a different charger, an excessive charging condition or abnormal

electrical currents may result and cause a chemical reaction within the battery pack. This may cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

■ Only use with the specified devices

œ If used with devices not specified for its use, abnormal electrical currents may

result and cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

■ Do not remove or damage the covering

œ Removing the covering, piercing with a nail, hitting with a hammer, stepping on, or

damaging the cover in any way may cause an internal short and result in a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

■ If you come in contact with electrolyte, immediately rinse with water

œ If the electrolyte gets into your eyes, you risk losing your eyesight. Do not rub

your eyes, wash them immediately with clean water, and seek medical attention right away. If electrolyte gets on your skin or clothing, it may cause irritation. Immediately wash with clean water.

■ Always insert orientated as indicated

œ When inserting the battery pack in the AC adapter/charger or digital disk camera,

make sure the positive (+) and negative (–) terminals are oriented correctly as indicated.

œ If the battery pack is used or charged with the polarity of the terminals reversed, an abnormal

chemical reaction will occur during charging and an abnormal current will flow during use. Both may cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

English

WARNING

■ If charging is not completed even after the specified time elapses, stop the charging immediately

œ If charging is continued, it may cause a fire, rupturing of the battery pack, eruption

or leakage of electrolyte, or overheating.

■ Keep out of the reach of children

œ The battery pack is not a toy and an unforeseeable accident may occur if

handled by children.

CAUTION

■ Recharge before use

œ Always first recharge the battery pack before using it for the first time, or before

using it after a long period of non-use. During recharging, the battery pack will be warm. This is normal and does not indicate a malfunction.

■ Take care when handling immediately after use

œ The battery pack may be extremely hot immediately after use. After turning

off the digital disk camera, allow time for the battery pack to cool before removing it.

■ Cautions concerning recycling

œ To help preserve the environment and promote the effective use of resources,

when the battery pack has ended its usable life, completely discharge it, place tape on its positive (+) and negative (–) terminals to prevent shorting, and hand it in for recycling.

œ If you must dispose of the battery pack yourself, always dispose of it as

nonflammable refuse and follow the regulations for your area.

English

DIGITAL DISK CAMERA AND AC ADAPTER/ CHARGER

WARNING

■ Do not use the digital disk camera or AC adapter/charger if it makes a strange noise, emits a strange odor, or if smoke comes out from it

œ If the digital disk camera or AC adapter/charger is used under these

conditions, it may cause a fire or electric shock.

œ If any of the above problems occurs, immediately perform the procedures given below and wait

to make sure no more smoke is emitted. Then take it to the dealer for service. Do not try to repair the problem yourself.

Digital disk camera

Turn off the digital disk camera.

2 Remove the battery pack. If you are using the AC adapter/charger, remove the power plug

from the power outlet.

AC adapter/charger

1 Remove the power plug from the power outlet. 2 If the battery pack is attached, remove it.

■ Do not modify or open the cabinet

œ High voltage circuits and a laser emitter are inside the digital disk camera, and

power supply circuitry is inside the AC adapter/charger. There is a danger of fire or electric shock if they are touched. Also, never disassemble the disk holder because the laser beam may enter your eyes and cause injury. Any internal check, setting, or repair should be performed by the dealer.

■ Do not insert metal objects or the like

œ Do not insert metal objects inside the devices or short any contacts inside the

AC adapter/charger. Doing so may cause a fire or electric shock.

■ Do not use while driving

œ Do not capture images, play back images, or watch the LCD monitor while

driving a vehicle. Doing so may cause an accident.

œ Be careful where you put down the digital disk camera or AC adapter/charger

inside an automobile. During sudden stops or turns they may fall behind the brake pedal and prevent braking.

œ When using the digital disk camera while walking, be very careful of your surroundings and

especially the traffic to avoid accidents.

■ Be aware of your surroundings during use

œ Pay close attention to your surroundings when using the digital disk camera.

Failure to do so may lead to an accident or injury.

œ Do not use the digital disk camera or AC adapter/charger inside an airplane or

elsewhere where use may be restricted.

English

■ Do not get the devices wet

œ This digital disk camera and AC adapter/charger are not water-resistant. Do not

allow them to get wet for doing so may cause a fire or electric shock.

œ Do not use in the bathroom or shower. œ If water does get inside the digital disk camera or AC adapter/charger,

immediately perform the procedures given below and contact the dealer for service. Do not try to repair the problem yourself.

Digital disk camera

1 Turn off the digital disk camera. 2 Remove the battery pack. If you are using the AC adapter/charger, remove the power plug

from the power outlet.

AC adapter/charger

1 Remove the power plug from the power outlet. 2

If the battery pack is attached, remove it.

■ Do not handle with wet hands

œ Handling with wet hands may cause an electric shock.

■ Do not use during a storm

œ To avoid the risk of being struck by lightning, do not use the digital disk camera

or AC adapter/charger during a thunderstorm. In particular, if used in an open field, you have an increased chance of being struck by lightning. Quickly seek refuge in a place that will protect you from lightning.

œ Do not touch the AC adapter/charger or power cord while it is plugged into a

power outlet during a thunderstorm. Doing so may cause an electric shock.

■ Do not place on an unstable surface

œ The digital disk camera or AC adapter/charger may fall, resulting in damage or

injury. If the digital disk camera or AC adapter/charger has fallen and its body is damaged, turn it off (unplug the power cord, etc.), remove the battery pack, and take it to the dealer for repair. Using the digital disk camera or AC adapter/charger after its body has been damaged may cause a fire or electric shock.

■ Do not look into the sun

œ Do not look through the digital disk camera at the sun or any other strong

source of light. Doing so may seriously injure your eyes or cause blindness.

English

■ Do not use the flash close to a person’s face

œ To prevent possible eye injury, do not use the flash near a person’s face

(especially young children or babies). If the flash is used close to a person’s opened eyes, there is a risk that it may damage that person’s eyesight.

■ Do not use where there is risk of explosion

œ Do not use the digital disk camera or AC adapter/charger in a location where there

is explosive gas, or any other flammable material in the air. Doing so may cause a fire or an explosion.

■ Keep out of the reach of children

œ The following may happen if children play with the digital disk camera or AC

adapter/charger:

They may wrap the strap around their neck and suffocate.

They may swallow the batteries or other small parts. In such a case, consult a physician immediately.

They may damage their eyesight if the flash goes off too close to their eyes.

They may hurt themselves.

■ Only use the specified battery pack and AC adapter/charger

œ Use only the supplied or separately sold UR-121 Li-ion battery pack. Use of a

different battery may cause a fire, an electric shock, the batteries to ignite, rupturing of the batteries, or other problem.

œ Plug only the supplied AC adapter/charger into the DC IN connector on the

digital disk camera. Do not plug in any other device into the DC IN connector. Also, this AC adapter/charger is for exclusive use with this digital disk camera (IDC-1000ZEX, IDC-1000ZE, IDC-1000ZU). Do not use it with any other device.

■ Use only to recharge the Sanyo UR-121 Li-ion battery pack

œ The supplied AC adapter/charger is for exclusive use with the supplied or

separately sold UR-121 Li-ion battery pack. Recharging a dry-cell battery or other type of rechargeable battery may cause excess heat, combustion, or leakage, and cause a fire, injuries, burns, or damage to nearby objects.

■ Do not invert the polarity ((+) and (– )) of the battery pack

œ Place the battery pack in the AC adapter/charger with the (+) and (–) terminals

oriented as indicated. If the battery pack is placed in the wrong orientation, the batteries may leak, overheat, explode, or be damaged. If the battery pack is charged with the polarity of the terminals reversed, it may cause a fire, rupturing of the battery pack, eruption or leakage of electrolyte, or overheating.

■ Use the AC adapter/charger with a 100 to 240 V AC power supply

œ If used with a power supply other than that specified, it may cause a fire or

electric shock.

English

■ Do not damage the power cord or DC cord of the AC adapter/charger

œ Do not place heavy objects on the cords. Do not place the cords near a heat

source. Do not excessively bend the cords, modify them, or secure them with staples.

œ If a cord is damaged, or if it does not plug properly into the digital disk camera or wall outlet,

contact the place of purchase.

■ Cautions concerning the power cord

œ Do not use the power cord with it wound up. Doing so may cause excessive

heat and a fire.

œ Do not leave the power cord plugged into the power outlet while the other end

is not plugged into the AC adapter/charger. The loose end can cause electrocution if touched with wet hands or if handled by children.

œ Only use the power cord supplied with the AC adapter/charger. If a different power cord is

used, it may be rated for a different current load, and that may cause a fire.

œ The supplied power cord is for exclusive use with the supplied AC adapter/charger. Do not use

it with other devices for it may cause a fire or electric shock.

■ Unplug the power cord from the power outlet when charging is finished

œ If the AC adapter/charger is left plugged into the power outlet for a long

period of time, there is a risk of fire.

■ Do not pull on power cord to unplug it

œ When unplugging the power cord, be sure to hold the power plug and slowly

pull it out of the power outlet. Pulling the cord portion may damage the power cord and cause a fire or electric shock.

■ Cautions when plugging in the battery charger

œ Securely plug the power cord all the way in the power outlet when using the

battery charger. If the battery charger is used with the power cord not fully plugged in, heat may generate and cause a fire.

œ If the power cord is damaged, or cannot be correctly plugged into the power

outlet, do not use the battery charger. Using the battery charger in this condition may cause a fire or electric shock.

œ Do not allow dust, etc., to build up on the power cord or power outlet. A

build-up of dust may cause a short circuit or generate heat and cause a fire.

English

CAUTION

■ Cautions when carrying the digital disk camera

œ Do not walk around with the digital disk camera hanging by the shoulder strap

and not properly secured. It may hit other objects, get damaged, or cause an injury.

œ Be careful not to drop the digital disk camera or AC adapter/charger or subject

them to strong shocks.

œ Make sure direct sunlight does not strike the digital disk camera lens or viewfinder, as that may

damage the internal parts. When not using the digital disk camera, be sure to always attach the lens cap.

œ When packaging or transporting the digital disk camera, be sure to reattach the protective

spacer that came with the digital disk camera at the time of purchase (see pages 18, 30).

■ Cautions during use and storage

œ Your digital disk camera and AC adapter/charger are precision instruments.

When using or storing the digital disk camera and AC adapter/charger, make sure to avoid the following locations to avoid damages.

Places in direct sunlight

Places near heat generating equipment (stoves, etc.)

Places with drastic humidity and temperature changes

Places that may get wet

Places close to an air conditioner or heater

Inside a car

Places where there is dust and dirt

Places where there is a fire burning

Places where volatile products are stored

Places subject to strong electromagnetic fields

Places subject to vibrations

Operating environment Digital disk camera

œ Temperature

0 to 35°C (operation)

œ Humidity

–20 to 60°C (storage)

AC adapter/charger

œ Temperature 0 to 35°C (operation)

œ Humidity 45 to 85% (operation, no condensation)

–20 to 60°C (storage)

œ When connecting the digital disk camera and AC adapter/charger, make sure the cords are not

caught on any objects.

■ Do not cover with a cover, rug, or similar object

œ Covering with a cover, rug, or similar object will cause the internal heat to rise and

may cause a fire.

30 to 90% (operation, no condensation) 10 to 90% (storage, no condensation)

45 to 85% (storage, no condensation)

■ Be aware that internal temperatures rise during use

œ Be aware that the internal temperatures of the digital disk camera and AC

adapter/charger will rise and may become hot to touch during use. Contact while hot for an extended period of time may cause light burns.

English

CAUTION

■ Do not connect the AC adapter/charger to an electronic transformer

œ Connecting the AC adapter/charger to an electronic transformer will cause a

malfunction and possibly a fire.

■ Cautions if the digital disk camera or AC adapter/charger is not going to be used for a long period

œ For safety, remove the battery pack. The battery pack may generate heat or

leak, and that may start a fire, cause injuries or burns, and damage any objects placed nearby. When the battery pack is removed for a long period, the date and time settings will be retained for approximately one year (or until the internal backup battery runs out).

CONCERNING THE LITHIUM BATTERY CR2025

WARNING

■ Cautions concerning the battery CR2025

œ One lithium battery CR2025 is used for the remote control and one is used

for backing up the internal clock. Do not use a battery other than the lithium battery CR2025.

œ Install the battery with the (+) and (–) terminals oriented as indicated. If the

battery is placed in the wrong orientation, it may cause a fire, overheating, or rupturing.

œ Do not recharge, short circuit, disassemble, modify, heat, or place the battery in a fire. Doing so

may cause a fire, overheating, or rupturing.

œ Do not hold the battery with metal tweezers or a similar tool. Doing so may cause a short circuit

leading to a fire, overheating, or rupturing.

œ Do not perform soldering on the battery or use, store, or leave it near a fire, under direct

sunlight, in a hot car, or other high temperature location.

œ Do not use the battery if it is leaking. œ If the electrolyte gets into your eyes, you risk losing your eyesight. Do not rub your eyes, wash

them immediately with clean water, and seek medical attention right away. If electrolyte gets on your skin or clothing, it may cause irritation. Immediately wash with clean water.

œ Keep the battery out of the reach of children. If the battery is accidentally swallowed, contact a

physician immediately. It may cause poisoning or suffocation.

œ When disposing of batteries, make sure to follow all applicable regulations. œ When disposing of the lithium battery, place tape on its positive (+) and negative (–) terminals

to prevent shorting. Do not mix the lithium battery with other batteries. Doing so may cause a fire or rupturing.

English

INSTRUCTIONS FOR THE PROPER USE OF YOUR DIGITAL DISK CAMERA

■ Cautions before capturing important images

œ Before capturing important images, make sure that the

digital disk camera is operating properly and in condition to capture the image properly.

œ Sanyo Electric shall not be held responsible for any

losses that result from images that could not be recorded, are erased, destroyed, or damaged in any way due to a problem with the digital disk camera, any of its accessories, or its software.

■ Cautions concerning copyrights

œ The images you capture with

your digital disk camera are for your own private use, any other use may violate the rights of copyrights owners.

■ Cautions when cleaning the digital disk camera and AC adapter/charger

Cleaning procedure

1 Turn off the digital disk camera and

remove the battery pack. (If the AC adapter/charger is connected, unplug its power cord.)

2 Remove the dirt with a soft cloth. 3 If the digital disk camera is

extremely dirty, wipe with a soft cloth moistened with a mild detergent diluted with water and wrung dry.

Caution

œ Do not use benzene or thinner products to clean

the digital disk camera or AC adapter/charger. Doing so may cause deformation, discoloration, or paint peeling. When using a chemically treated cloth, carefully read its instructions and warnings.

œ Do not spray insecticides, or volatile sprays on the

digital disk camera or AC adapter/charger. Do not leave rubber or vinyl objects against the digital disk camera or AC adapter/charger for a long period. They may cause deformation, discoloration, or paint peeling.

■ Cautions when cleaning the lens

œ If the lens gets dirty, use a commercially available air blower or a cleaning cloth for

photographic equipment to clean it.

œ It is also possible to clean the viewfinder (see page 166).

■ Cautions concerning the battery pack terminals

œ Periodically clean with a dry cloth the terminals of the battery pack, digital disk camera, and AC

adapter/charger.

œ Do not touch the terminals with your bare hands. Doing so will allow contaminants from your

hands to adhere to the terminals and oxidize, increasing the contact resistance. If the contact resistance increases, the usable life of the battery pack will diminish and recharging may become impossible.

■ Cautions when not using the digital disk camera

œ Attach the lens cap whenever you are not using the digital disk camera.

When not using the digital disk camera for a long period

œ Remove the battery pack. However, when the battery pack is removed for a long time, the

digital disk camera functions may begin to not work properly. Periodically reinstall the battery pack and check the digital disk camera functions.

œ If the battery pack is left in the digital disk camera, a small amount of power is still used even if

the digital disk camera is turned off. If the battery pack is left in the digital disk camera for a long period, it may become completely discharged and loose its ability to be recharged again.

English

■ Cautions concerning condensation

œ Using the digital disk camera with condensation inside it may damage the digital disk camera.

Be careful of condensation under the following conditions

œ When moving the digital disk camera

suddenly from a cold place to a warm place.

œ When the ambient temperature changes

drastically, such as when a heater is turned on to quickly heat the room.

œ When the digital disk camera is placed in the

path of cool air from an air conditioner.

œ When the digital disk camera is placed in a

location of high humidity.

If condensation seems likely to form

œ Place the digital disk camera in a plastic bag

and seal it, and then wait until the digital disk camera has reached the ambient temperature.

■ Cautions concerning undesired interference

œ The digital disk camera or AC adapter/charger may create undesired interference if used close

to a television or radio. To reduce the amount of undesired interference emitted, cores are attached to the supplied AV cable and the DC cord of the AC adapter/charger. Do not remove these cores. Also, when using the supplied microphone or IEEE1394 cable, attach one of the supplied cores as shown below.

Supplied AV cable

Core

Supplied AC adapter/charger

When using the supplied microphone or IEEE1394 cable

œ Attach a supplied core as shown below.

1 Make a loop in the cord just behind the

plug.

English

Core

Ferrite core (small)

Approx. 5 cm

Ferrite core (large)

Ferrite core (small)

2 Close the core.

œ Be careful not to pinch the cord with

the core when closing the core.

Approx. 5 cm

■ Cautions concerning magnetism

œ Do not place credit cards, bankcards, floppy disks, or other items that may

be damaged by magnetic fields near the speaker. Data may be lost or the magnetic strips on cards may be damaged.

Speaker

■ Cautions concerning the iD PHOTO disk

œ The iD PHOTO disk is provided for use with devices displaying the iD

PHOTO logo mark for the storage and playback of image data. Do not

use with devices that do not display the iD PHOTO logo mark for doing so may cause damage to the device and the disk.

œ The iD PHOTO disk is a precision device. Do not bend, drop, or subject

it to strong forces or shocks.

œ Do not open the shutter and touch the iD PHOTO disk inside. œ Immediately after use, the iD PHOTO disk may be very hot. Before

removing the iD PHOTO disk, turn off the digital disk camera and wait until the disk cools.

œ Keep out of the reach of children. Children may put the disk in their mouths or perform some

other unforeseeable action.

Cautions when handling the iD PHOTO disk

œ Avoid storing or using the iD PHOTO disk in places similar to those given below for they may

cause damage or the disk to malfunction.

Places in direct sunlight or near heat generating equipment

Places extremely cold

Places with excessive dust, dirt, or humidity

Places subject to vibrations

Places with drastic humidity and temperature changes

Places with excessive static electricity or electromagnetic noise

œ Do not place the iD PHOTO disk near magnets or in strong magnetic

fields.

œ Do not disassemble the iD PHOTO disk. œ Do not allow the iD PHOTO disk to get wet. œ Wipe away dust or dirt with a soft, dry cloth. Do not use benzene, thinner, or other solvents. œ Do not use in locations with drastic temperature changes or in locations

with a high humidity. These locations are subject to condensation. If condensation occurs in the iD PHOTO disk, reading from and writing to the disk may become impossible.

œ Before using an iD PHOTO disk for the first time, be sure to format it with your digital disk

camera first (see pages 155, 157).

œ Before capturing important images, it is recommended to first try capturing images to make

sure that the digital disk camera works properly. Also, to further ensure that images are captured properly, perform a full format beforehand (see page 157).

œ Attach the labels carefully so that they will not come off accidentally. If the label comes off

during insertion or removal of the iD PHOTO disk from the digital disk camera, it may cause damage (see page 18).

œ Do not allow dirt or other foreign particles to enter the shutter portion of the iD PHOTO disk.

Wipe away any dirt with a soft, dry cloth. Do not use benzene, thinner, or other solvents.

Shutter

English

Cautions when carrying or storing the iD PHOTO disk

œ Always remove the iD PHOTO disk from the digital disk camera after you have finished using it. œ When not using the iD PHOTO disk, always keep it in its protective case. œ Do not carry the iD PHOTO disk inside trouser pockets, as it may become damaged when you

sit down or make other movements that may apply forces.

Making sure that data on your iD PHOTO disk does not become erased

Move the write-protect tab to the “ è” mark.

œ Move the tab using a sharp item such as the end of a

ballpoint pen.

œ Saving (adding data such as capturing images or

recording), deleting, and formatting will become impossible.

œ To make it possible to perform saving, deleting, and

formatting again, move the tab back to its original position.

Write protected Write enabled

■ Cautions concerning data storage

œ The iD PHOTO disk is a highly reliable storage device, however it is recommended that any

important data be copied onto a separate media (such as a floppy disk, hard disk, or MO disk) for added safety against unforeseeable accidents.

œ Stored data may be lost (or corrupted) in cases such as those listed below. Sanyo Electric will

not be held responsible for any damage or lost profits arising from the loss of data.

If the iD PHOTO disk is used incorrectly.

If the iD PHOTO disk is not inserted correctly into the digital disk camera.

If the iD PHOTO disk is subjected to electrical or mechanical shocks or other forces.

If the iD PHOTO disk is removed from the digital disk camera or if the digital disk camera is turned off during reading or writing operations.

If the iD PHOTO disk has reached the end of its usable life.

■ Cautions concerning vibrations

œ If the digital disk camera is subject to vibrations or shocks during image capturing or the

playing back of data, the data may not be properly read or written. Therefore always be careful not subject the digital disk camera to vibrations or shocks during use.

■ Cautions concerning rises in temperature

œ During use, ã or ä may appear to tell you that the internal temperature of the digital disk

camera is rising. If this occurs, stop operations and turn off the digital disk camera as soon as possible. See pages 167 and 168 for further information.

Rising temperature mark

English

HIGH TEMP

pOK

High temperature mark

CHECKING THE INCLUDED ACCESSORIES

Open the box and check that all the accessories listed below are included. If a part listed here is not present or damaged, contact the place of purchase.

The page numbers listed next to the part names are the page numbers where that part is explained in detail.

œ Grip belt [page 48] œ Shoulder belt [page 48] œ AV cable [page 71]

œ Battery pack and

protective cover (Li-ion battery pack UR-121) [pages 24, 27]

œ iD PHOTO disk, protective

case, labels (730 MB:

DSM-D730A) [pages 30, 155]

Attaching the labels

Protective caseiD PHOTO disk

œ USB interface cable œ IEEE1394 interface cable

œ AC adapter/charger and

power cord

(NC-LSC04WSA) [pages 24, 29]

œ Protective spacer [page

30] (Located inside disk holder at the time of purchase. Use to transport the digital disk camera.)

œ Lithium battery for clock

backup (CR2025) [page 23]

and 3 cores

œ Remote control [pages 22,

36] (Lithium battery is installed at the time of purchase.)

œ Lens cap [page 12]

Press here to attach and remove the lens cap.

œ Core [page 15]

œ Software: 3 CD-ROMs

œ Scart adapter (for IDC-1000ZE only)

Use this adapter to connect an AV cable to a television or VCR equipped with the EURO-AV type audio/video input terminal.

œ Microphone [page 49]

English

PARTS NAMES

Front

The page numbers listed next to the part names are the page numbers where that part is explained in detail.

1 F1 button [pages 55, 84] 2 F2 button [pages 55, 85] 3 Control dial [pages 52, 66, 87] 4 RETURN button [pages 55, 87] 5 Microphone [page 79] 6

W.BAL (white balance) button [page 96]

7 EXP (exposure) button [page 92] 8 FOCUS button [page 90] 9 Zoom switch [page 74] F Lens [page 14] G Remote control sensor [page 36] H Self-timer lamp [pages 36, 81] I Shutter release button [pages 35, 51]

English

J Flash [page 76] (Press the flash pop-up

button to stand up the flash bulb.)

Flash bulb

Flash pop-up button

K Flash pop-up button [page 76]

Rear

The page numbers listed next to the part names are the page numbers where that part is explained in detail.

1 Mode display panel [pages 32, 39, 41] 2 Mode selector dial [page 47] 3 Grip belt holder [page 48] 4 Viewfinder [pages 32, 50] 5 Monitor switch [page 32] 6 Arrow button [page 52] 7 AUTO/MAN button [page 89] 8 Shoulder belt holder [page 48]

9 Terminal cover [pages 29, 49, 71] F MIC (microphone) input terminal [pages

49, 68]

AV output terminal [page 71]

H DC IN (external DC power input) terminal

[page 29]

I Speaker [page 16] J Focus ring [page 90]

English

1 Power button [pages 32, 35] 2 EJECT lever [pages 30, 31] 3 Disk holder [pages 30, 31] 4 Interface cover [page 159] 5 USB terminal [page 159] 6 IEEE1394 terminal [page 160]

English

7 MODE button [pages 43, 54] 8 SET button [pages 43, 54] 9 CAMERA/PLAY switch [page 47] F LCD monitor [pages 32, 50] G Diopter adjustment lever [page 33]

Bottom

The page numbers listed next to the part names are the page numbers where that part is explained in detail.

1 Tripod stand hole [page 80] 2 Grip belt holder [page 48] 3 BATT (battery cover release) knob [pages

23, 27]

4 Battery pack cover [pages 23, 27] 5 Battery pack mating area [page 27] 6 Clock backup battery cover [page 23]

Remote control

The page numbers listed next to the part names are the page numbers where that part is explained in detail.

Excluding the CH button, all buttons perform the same operation as the button of the same name on the digital disk camera itself.

Infrared emitter [page 36]

2 Shutter release button [page 51] 3 MODE button [page 54] 4 SET button [page 54] 5 Arrow button [page 52] 6 Battery holder [page 37] 7 W (zoom wide) button [pages 38, 74] 8 T (zoom telescopic) button [pages 38, 74] 9 CH button [page 38]

English

POWER SUPPLY

Use only the UR-121 battery pack with your digital disk camera. To operate the digital disk camera using a power outlet, use the supplied AC adapter/charger.

Your digital disk camera can be operated using two different types of power supplies:

œ The supplied battery pack [pages 24 to 28] œ The supplied AC adapter/charger (using the AC power supply from an AC power outlet) [page

29]

Caution

œ Use only the supplied or separately sold UR-121 battery pack. Use of another battery pack

may damage the digital disk camera.

œ The supplied or separately sold UR-121 battery pack is for the exclusive use with this digital

disk camera. Use with a different camera may cause a fire or electric shock.

Installing the clock backup battery

Follow the procedure below to install the battery for backing up the date and time settings, various camera settings, and other disk information. The backup lithium battery will last approximately one year and then will require replacement (one CR2025 battery).

Open the battery pack cover.

1 Press and hold down the BATT knob

on the digital disk camera bottom.

2 Pull the battery pack cover toward the

front of the digital disk camera and then lift it up.

Open the clock backup battery cover

and install the clock backup battery.

œ The clock backup battery (CR2025) is

installed in the bottom of the section for the battery pack.

œ Wipe the battery clean with a soft, dry

cloth and then install it with the positive (+) terminal facing upward.

NOTE Saving the camera settings

œ Whether a fully charged battery pack is installed, a clock backup battery is installed, or AC

power is used with the AC adapter/charger, the manual mode settings and other camera settings will be saved even when the digital disk camera is turned off. However, when c is selected at the hold settings menu, the settings are not saved and are returned to their initial settings (see page 112).

English

Installation Removal

Clock backup battery cover

Charging the battery pack

The battery pack is not charged at the time of purchase and therefore needs to be charged before use. Always use the supplied AC adapter/charger to recharge the battery pack.

Follow the procedure below to charge the supplied battery pack or a new UR-121 battery pack used for the first time, or to recharge a battery pack that has become low in charge.

Remove the protective cover from the battery pack.

Insert the battery pack into the AC adapter/charger.

1 Orient the battery pack as shown in the figure on the

right, align the j marks on the sides of the battery pack and AC adapter/charger, and insert the battery pack in the AC adapter/charger.

2 Push in the direction of the arrow.

Insert the supplied power cord into the socket on the

AC adapter/charger.

œ Insert the power cord straight and until it is fully seated.

Plug the power cord into a power outlet (AC 100 to

240 V).

œ Charging will start automatically. œ During charging, the BATTERY CHARGE lamp will

light red.

œ Charging will take approximately 120 minutes. œ When charging is completed, the BATTERY CHARGE

lamp will turn off.

Battery pack

Protective cover

AC adapter/charger

Battery pack mating area

Power cord

j mark

To AC

BATTERY CHARGE lamp (red)

NOTE

œ Recharge the battery pack just before use or on the day before use. If charged and left unused,

the charge will slowly leak reducing the time the battery pack can be used.

œ Avoid storing the battery pack with it near full charge. It is recommended to store the battery

pack when it is near fully discharged.

œ If the battery pack is completely discharged, it may become unable to be recharged again. To

avoid this, charge the battery pack for at least five minutes every six months.

English

When the BATTERY CHARGE lamp turns off, unplug

the power cord from the wall outlet.

Remove the battery pack from the AC

adapter/charger.

œ If you are not going to attach the battery pack to the

digital disk camera right away, then place it in its protective cover.

BATERY CHARGE lamp (red)

AC ADAPTER lamp (green)

NOTE

œ You can use the digital disk camera with the AC power supply even while charging (see page

29). In this situation, charging is stopped automatically and AC power is supplied to the digital disk camera. When the digital disk camera is turned off, charging is resumed.

œ During charging, the battery pack and AC adapter/charger will become warm. This is not a

malfunction.

If noise is received by a radio or television during charging

œ Perform the charging in a location away from the radio or television.

Ambient temperature during charging

œ The ambient temperature during charging should be kept between 10 and 35°C. If the

temperature drops below 10°C, the characteristics of the battery pack may not allow it to become fully charged.

Recharge the battery pack before use in the situations given below

œ If the battery pack has not been used for a long period of time. œ If the battery pack is new and is being used for the first time.

English

The BATTERY CHARGE and AC ADAPTER lamps

The BATTERY CHARGE and AC ADAPTER lamps allow you to check the condition of the battery pack and AC adapter/charger. If either of the lamps begins flashing, it indicates a problem. Refer to the table below to check and remedy the problem.

BATTERY CHARGE lamp

AC ADAPTER lamp

Off Power is not being supplied

œ Plug the power cord into a power outlet when using

the AC adapter/charger. Charging is complete œ Unplug the power cord from the power outlet.

On Charging Flashing There is a problem with the battery pack

œ Immediately remove the battery pack. œ Do not use a malfunctioning battery pack (the

battery pack has likely ended its usable life).

Off The AC adapter/charger is not connected properly

œ When running the digital disk camera with the AC

power supply, plug one end of the power cord into

power outlet and the other into the power supply

socket on the AC adapter/charger, and plug the DC

cord into the DC IN terminal on the digital disk

camera. The digital disk camera is not turned on œ Press the power button to turn on the digital disk

camera.

On AC power is being supplied to the digital disk camera Flashing There is a problem with the AC adapter/charger

œ Immediately unplug the power cord from the power

outlet.

œ Do not charge the battery pack. œ Contact the place of purchase.

HELP If the BATTERY CHARGE lamp does not turn off

œ If more than 150 minutes have elapsed since charging was begun and the BATTERY

CHARGE lamp does not turn off, there is a malfunction. If this occurs, immediately stop charging and contact the place of purchase.

English

Installing the battery pack

Open the battery pack cover.

1 Press and hold down the BATT knob on the digital

disk camera bottom.

2 Pull the battery pack cover toward the front of the

digital disk camera and then lift it up.

Attach the charged battery pack to the battery pack

mating area.

1 Orient the battery pack as shown in the figure below,

align the edges of the battery pack and the battery pack mating area, and insert the battery pack in the battery pack mating area.

2 Push in the direction of the arrow.

d mark

Battery pack cover

English

Close the battery pack cover.

1 Close the battery pack cover. 2 Push it towards the back of the digital disk camera

until it is secured in place.

Removing the battery pack

Caution

œ Before removing the battery pack, be sure to turn off the digital disk camera. Removing the

battery pack while the power is still on may damage the digital disk camera or data on the disk.

If the digital disk camera is turned on, turn it off (see

page 35).

œ Press the power button for more than one second. œ When the power is turned off, the displays on the

mode display panel and LCD monitor (or viewfinder) turn off.

Open the battery pack cover.

1 Press and hold down the BATT knob on the digital

disk camera bottom.

2 Pull the battery pack cover toward the front of the

digital disk camera and then lift it up.

Power button

Viewfinder

Mode display panel

LCD monitor

Battery pack cover

Remove the battery pack.

œ Slide the battery pack toward the front of the digital

disk camera and lift it upward. (Be careful not to drop the battery pack when removing it.)

œ Immediately after use, wait a few minutes before

removing the battery pack because it may still be hot.

Close the battery pack cover.

English

Using the AC power supply

Use the supplied AC adapter/charger to operate the digital disk camera with an AC power supply (by connecting to a power outlet).

Caution

œ The AC adapter/charger is for exclusive use with this digital disk camera (IDC-1000ZEX,

IDC-1000ZE, IDC-1000ZU). Do not use it with any other device.

œ If the AC ADAPTER lamp is flashing, there is likely a problem with the AC adapter/charger. If it

is flashing, immediately unplug the power cord from the power outlet and contact the place of purchase (see page 26).

Insert the supplied power cord into the socket on the

AC adapter/charger.

œ Insert the power cord straight and until it is fully seated.

Plug the DC cord into the DC IN terminal on the

digital disk camera.

Plug the power cord into a power outlet (AC 100 to

240 V).

Turn on the digital disk camera (see page 32).

œ When the digital disk camera is turned on, the green

AC ADAPTER lamp turns on.

œ If charging is being performed at this time, charging is

stopped automatically and AC power is supplied to the digital disk camera. (The red BATTERY CHARGE lamp turns off and the green AC ADAPTER lamp turns on.)

BATTERY CHARGE lamp (red)

AC ADAPTER lamp (green)

Power cord

AC adapter/ charger

Power button

DC cord

DC plug

DC IN terminal

Terminal cover

To AC

English

+ 145 hidden pages