Sanyo HV-DX350A Instruction Manual

INSTRUCTION MANUAL

PAL

DVD Player + Video Cassette Recorder

HV-DX350A

Please read this manual carefully before connecting your DVD+VCR and operating it
for the first time.

Keep the manual in a safe place for future reference.

Important Safeguards

Product information

Product information

All the safety and operating instructions should be
read before the unit is operated.

The safety and operating instructions should be
retained for future reference.

All warnings on the unit and in the operating
instructions should be adhered to.

All operating and use instructions should be followed.

Unplug this unit from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.

Do not use attachments unless recommended by the
unit’s manufacturer as they may cause hazards.

Do not use this unit near water- for example, near a
bath tub, wash bowl, kitchen sink or laundry tub, in a
wet basement, or near a swimming pool.

Do not place this unit on an
unstable cart, stand, tripod,
bracket, or table. The unit may
fall, causing serious injury to
a child or adult as well as
serious damage to the unit.
Use this unit only with a cart, stand , tripod, bracket,
or table recommended by the manufacturer.

A unit and cart combination should be moved with
care. Quick stops, excessive force, and uneven

surfaces may cause the product and cart combination
to overturn.

9 Ventilation

Slots and openings in the case are provided for
ventilation to ensure reliable operation of the unit and
to protect it from overheating. These openings must
not be blocked or covered. These openings must not
be blocked by placing the unit on a bed, sofa, rug, or
other similar surface. This unit should never be placed
near or over a radiator or heat radiator. This unit
should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been
adhered to.

10 Power Sources

This unit should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of power supply to your home,
consult your dealer or local power company. For units
intended to operate from battery power, or other
sources, refer to the operating instructions.

11 Power-Cord Protection

Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the unit.

12 Lightning

For added protection for this unit during a lightning
storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system. This will
prevent damage to the unit due to lightning and
power line surges.

13 DISC TRAY

Keep your fingers well clear of the disc as it is closing.
It may cause serious personal injury.

14 Overloading

Do not overload wall outlets of extension cords as this
can result in a risk of fire or electric shock.

15 Object and Liquid Entry

Never push objects of any kind into this unit through
openings as they may touch dangerous voltage

PORTABLE CART WARNING

(symbol provided by RETAC)

Advantages of This Product .....

Product information

• DVD, VCD, CD, CD-R(MP3), CD-RW, VHS

• Watching DVD while recording TV
broadcasts

• Integrated remote control (VCR, DVD)

• VISS function

• Multiplex sound playback/record

• High Sound Quality of 6 head Hi-Fi

• Simple record function

• MP3 file playback function (CD-R disc
having records of MP3 files)

• Screensaver function (DVD)

• Coaxial digital Audio output (PCM, Dolby
Digital, dts)

You can enjoy high-level digital audio by
connecting with amp embedded with Dolby
Digital / dts decoder.

• Analog audio 2-channels output for
DOWNMIX (x1)

• Composite video output (x1)

• Slow Forward playback (DVD)

• Fast Forward / Reverse playback

• Search of title, chapter, and time in DVD
disc, and search of time and track time in
VCD.

• Various TV aspect (DVD)

4:3 for Pan and Scan, 4:3 for Letter Box, and
16:9 for Wide

• Repeat playback (title, chapter, and part for
DVD/ track, disc, and part for VCD/CD)

• Selective Play (DVD/VCD/CD)

You can select and play the desired title /
chapter of DVD and track of Video CD/CD in
STOP mode.

• 11 languages OSD (On Screen Display)
function (DVD)

You can select and display OSD in 11 languages.

• Parental Lock function (DVD)

This function can prevent playback of software
that may be unsuitable for children.

• Multi Audio function (DVD)

The audio soundtrack can be heard in up to 8
languages. In the case of SVCD or VCD, it
depends on the disc. (The number of audio
languages depends on the software.)

• Multi Subtitle function (DVD)

The subtitle can be seem in up to 32 languages.
In the case of SVCD or VCD, it depends on the
disc. (The number of subtitle languages depends
on the software.)

• Multi Angle function (DVD)

This function allows you to choose the viewing
angle of scenes which were shot from a number
of different angles. (The number of angles
depends on the software.)

• Screen zoom function (DVD/VCD)

Identification of Controls

Product information

! Power (STANDBY/ON) button

Use to power the device on/off if AC power supply
is connected.

@ Place to insert videotape
# Disc tray
$ VIDEO INPUT jack
% AUDIO INPUT jacks
^ EJECT button
& RECORD button
* CHANNEL -/+ (Channel Down/Up) button
( Operation Display Window

Display operation of device. For more information,
see “Operation Display Window” (refer to page 8).

) SELECT button

Use to change DVD mode to VCR mode, and vice
versa.

1 STOP button

Use to stop playing.

2 REWIND button

Use to rewind currently being played videotape or
disc; or to playback back rapidly.

3 Playback/PAUSE button

Playback videotape or disc.
Press this button to pause a screen.

4 FAST FORWARD button

Use to wind currently being played videotape or
disc; or to playback rapidly.

5 OPEN/CLOSE Tray button

Main body (front panel)

!

%

& *

)

12

3 4 5

^

@#

$

(

Identification of Controls

Product information

! Power Cord

It is a jack for supplying power to the unit.
Connect to outlet in a wall.

@ AUDIO OUTPUT Jack
# COMPONENT OUTPUT Jack
$ Digital Output (COAXIAL) Jack

To enjoy sound quality of theater level in
home, connect this jack with amp or unit
embedded with digital audio decoder.

% A/V OUTPUT Jack
^ A/V INPUT Jack
& Connection to ANTENNA Cable
* Connection to TV

Main body (Rear Panel)

!

@ # % ^ &

$ *

Remote Control

Product information

!

#

@

$
%

^

&

(

)

2

4
5

7

9

“

#

‘

=

q

w

e

R

r

T

Y

0

+

E

t

y

W

Q

*

3

1

6
8

! [DVD] Open/Close button, [VCR] Eject button
@ VCR SELECT button
# [DVD, VCR] Number button, [VCR] Tracking -/+ button
$ System button [VCR] This button is not available for

this set [DVD] Activates Progressive Scan button

% SETUP button
^ [DVD, VCR] Move/Select in OSD, [VCR] Channel Up/Down

button

& [DVD] Title /PBC button
* [DVD] AUDIO Language Select, [VCR] AUDIO Select

button

( [DVD] Subtitle Select button
) Reverse Search button
1 Play/Pause button
2 [DVD] PREVIOUS button (move into a previous

chapter or track)

3 [VCR] Record Speed button
4 [VCR] Record button
5 [VCR] TV/VCR button
6 3D button (This button is not available for this set)
7 [VCR] CM SKIP
8 [VCR] Replay button
9 Power button
0 DVD SELECT button
“ [VCR] INPUT Selection button
‘ Clear button
+ [DVD, VCR] OSD Display button
= OK/ENTER button
Q [DVD] Menu button
q [DVD] Chapter/Title/Time Search button
W [DVD] Zoom button
w Forward Search button
E Stop button
e [DVD] Next button (Move into a next chapter or

track) , [VCR]

Frame Advance button in pause mode

R

[DVD] Repeat Playback button

r [DVD] REPEAT a defined period from A to B button
T [DVD] Angle button
t

[DVD] Mark button

Y

[DVD, VCR] PROGRAM button

y [VCR] LAST CHANNEL button (If you move channels

using the [PR+/PR-] button, return to the previous TV
channel which was being watched)

Press the power[] button of the remote for
about 5 seconds. No buttons of front panel can

then operated and Lock indicator (“ ”)
will be displayed on window display. To release
child lock, press any button on the remote
control.

POWER ON

Player will be POWER ON if any button of the
remote control is pressed.

Child Lock !

Connecting your player with a RF lead

Installation

■ Before you start, unplug all the equipment from the mains supply.

(Option 2) - How to Connect with Audio/Video jack

INPUT 1

ANT IN

INPUT 2

REAR PANEL OF DVD-VIDEO

REAR PANEL OF TV

AUDIO/VIDEO CABLE

£ (If there is Audio/Video InPUT jack in TV)

Connect Video Out jack in DVD-Video to Video Injack in TV, and AUDIO Out jack in DVD-Video to
AUDIO IN jack in TV with connecting cable of Audio/Video jack.

Select VCR mode by pressing TV/INPUT button in TV, you can view a clearer screen and sound than
connection with RF cable only.

• VHF: 1 ~11 channels of TV / • UHF: 21~69 channels of TV

• CATV: Broadcasting is transmitted with cable from broadcasting station by contract with the station and
consumers. It does not need any antenna.

• In/Out jack in Audio/Video terminal:

- In: A jack used to receive signal required in this unit from other units.

- Out: A jack used to send signal of this unit to other units.

• Connect with Audio/Video terminal, you can enjoy more clear video and audio.
(Use INPUT button in this REMOTE to select video mode.)

Connecting with Other VCR or Camcorder

Installation

¡ Connect Audio/Video Out jack in Camcorder(or playback video) to Audio/Video In jack in rear

panel (or front panel) of DVD-Video with connecting cable.

™ Connect “ANT. IN” jack in TV to “TV” jack in DVD-Video with RF cable.
£ To record contents of camcorder or playback video with DVD-Video, insert recording tape attached

recording tab in DVD-Video.

¡ Turn on DVD-Video.
™ Press [INPUT] button of remote control and adjust DVD-Video to display “AV” or “AV.F” in TV

screen.

£ Press [PLAY] button in Camcorder or playback video.
¢ Press [REC] button in DVD-Video if you want to record contents of camcorder or playback video.
∞ Press [Pause] button in DVD-Video when unnecessary or undesired scene is displayed in recording.

(Caution) Recording is released automatically after 5 minutes since pressing [PAUSE]

button. Press [REC] button if you want to record again.

¡ Turn DVD-Video on.
™ Press [INPUT] button of remote control and adjust DVD-Video to display “AV” or “AV.F” in TV screen.
£ Insert tape in camcorder and play it back.

How to Copy(Edit) Tape with Other VCR or Camcorder

How to Playback Chapter Photographed by Camcorder

Connecting to a television with
Component jack and a Dolby Digital Amp.

Installation

How to Connect

■ Use in COMPONENT In jack attached in TV or amp supporting Dolby Digital.

(NOT SUPPLIED)

(L) AUDIO IN (R)

REAR PANEL OF DVD-VIDEO

DOLBY DIGITAL DECODER-AMPLIFIER

TV CONNECTIONS

COMPONENT IN

CONNECTING CABLE

Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are registered trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Initial Installation

Basic Operation

Press the [OK] button to confirm the recommended RF channel.
Should you wish the stations to have the same numbers as those

used on the TV, follow the instructions in "Sorting programme
locations" on page 28.

Else ...
exit the basic installation function and enjoy your player.

7

Should you wish the stations to have the same numbers as those
used on the TV, follow the instructions in "Sorting programme
locations" on page 28.

Else ...
Press the SETUP button to exit the set-up menu and enjoy your
player

8

If other stations are positioned on near the current RF OUTPUT CH,
the guide message appears automatically.

The player recommends the optimal RF OUTPUT CH number
automatically.

6

If the clock has not been set, the clock setting screen will appear.
Please see “Setting time and date” on page 20.

5

• If the signal from the player is coming into the TV through
the RF lead, the picture will disappear when you press OK at
step 8. You will need to re-tune your television to the new
UHF transmission channel.

Up [PR+], down [PR-], OK and 'confirm'

• Notice the on-screen prompts which the video recorder generates to tell you which button to press.
In general the up and down 'navigation' buttons select or highlight something and the OK button
confirms it .

• [PR+] and [PR-] are the same buttons as 'up' and 'down'.

• In the DVD section it is usually the left and right buttons which 'select'.

CLOCK SET

0-9:SETUP (HOUR)

/➝:CORRECT SETUP:END

TIME - - : - ­DATE - - / - - /- - - -

➝

PLEASE CHANGE THE TV
CH TO 34.

IMPORTANT!

RF OUTPUT SET

0-9:SELECT(21-69)
OK:CONFIRM SETUP:END

CURRENT CH 36
RECOMMENDED CH 34

MANUAL SET

PR01 P-01 PR08 P-08
PR02 P-02 PR09 P-09
PR03 P-03 PR10 P-10
PR04 P-04 PR11 P-11
PR05 P-05 PR12 ---­PR06 P-06 PR13 ---­PR07 P-07 PR14 ----

PR+/-:SELECT
OK:CONFIRM SETUP:END

Output Select

Basic Operation

Press [DVD] button.

If DVD mode is correctly selected, DVD on the operation display window is lit.
Then, REMOTE button works as DVD function. Press the [DVD] button, then
the mode of DVD-Video Player becomes to the OPERATION mode.

Press [VCR] button.

If VCR mode is correctly selected, DVD on the operation display window
goes out. Then, REMOTE button works as VCR function. Press the [VCR]
button, then it becomes to the VCR OPERATION mode.

Press [INPUT] button.

When you press [INPUT] button, BROADCASTING RECEPTION and EXTERNAL INPUT is selected. But, it
is not operated in PLAY, REC and DVD mode.

To Select DVD

To Select VCR

To Select Watch Modes or External Input

VCR Playback

Basic Operation

Press [ ] button to power on.

Press [VCR] button of remote control to change into VCR mode.

Insert the desired tape.

If you want to playback it, press [PLAY/PAUSE] button.

When the operational status is flickering or poor, adjust it with [TRACKING +/-]
button.

1
2

3

To stop it, press [ ] button.

If you want to stop playback, press [STOP] button.

4

Press [EJECT] button in the front part or [OPEN/CLOSE] button on remote
control to remove the tape.

5

If the product, which
has a auto-detector,
detects a
contaminated head(s),
it shows the
conditions to notice
the contamination on
screen.

Various Playback Methods

■ If you want fast forward (or reverse) playback, press [

√√√√

] or [

œœœœ

] button in

Playback mode. You can watch fast playing (rewinding) screen.

* NOTE:

You might see no color noise band when you fast forward (or reverse)
playback the tape which is recorded in LP mode.

■ If you want Still picture, press [PLAY/PAUSE] in Playback mode. You can watch the
desired screen in pause status.

■ If you want slow-motion playback, press [

√√√√

] button in Pause mode. You can

watch the desired screen in the slow forward playback.

* NOTE: VCR doesn’t have Slow Reverse Playback function.

■ If you want to watch a series of screens one by one, (FRAME ADVANCE) press
[NEXT

√√√√

❚ ] button in Pause mode. Each time you press this button, the picture

advances one frame.

■ If you press [REPLAY] button in playback mode, the player quickly rewinds 15
seconds of the tape and plays it.

■ If you press [CM SKIP] button in playback mode, the player quickly skips 30
seconds of the tape and plays it.

To Adjust Display

This product includes automatic Tracking function and enables users to enjoy clear picture
without an additional operation. Provided that the following problems can be solved by
the manual adjustment, which improves display quality. (During automatic display
adjustment, “Adjusting Display” are displayed on TV screen.)

- If the screen is poor in Playback mode,

- If noises occur in the upper or lower part of screen in slow playback mode,

- If paused picture vibrates up and down.
Use [TRACKING +/-] buttons of remote control to adjust the display suitable for watching.

Recording

Basic Operation

“This product incorporates copyright protection technology that is protected by
U.S patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.”

1

1 Insert the desired DVD disc.

When it is a DVD disc with copy protect function, you can’t copy it.

Insert a recordable tape.

2

2 Press [REC] button during playing of DVD.

DVD plays and VCR starts recording.

3

3 If you press STOP [ ] button in DVD mode, DVD and VCR will stop at the

same time.
If you press STOP [ ] button in VCR mode, VCR stops to record and DVD

continues to play.

To Copy From DVD To Videotape

CHECK IT!

* Only record in interlaced mode

This DVD+VCR can only record in interlaced mode.
To get proper picture, press [SYSTEM] to “INTERLACED” before recording.

Tuning in New Stations

VCR Operation

■ The TV and player are switched on.

■ To see the picture from your player, press the input or AV (Audio/Video) button on the TV.

To complete the set-up of your video recorder when the auto
set has not stored all of the channels or when you wish to
store a new channel.
Call the video’s "SETUP", choose "PR PRESET".

1

Select "MANUAL SET".

2

Choose any unused location number "----" or "P-xx" ...
It's simplest to use the same location number on both the TV

and video.
... and confirm.

3

Set the station you want:

• the programme location number;

• the broadcast system you want (Aerial(CH) or Cable(CC)),

• You can directly enter the real channel number with the
[0 to 9] buttons, or search by pressing [

œœ /√√

],

• The fine tuning you can adjust,

• Change or create the station name.

4

Once you see the station you want, store it.
Tune in further stations (from step 3 onwards) or exit tuning

mode.

5

PR PRESET

AUTO SEARCH
MANUAL SET
PR ERASE
PR ALIGN

PR+/-:SELECT
OK:CONFIRM SETUP:END

MANUAL SET

PR+/-: UP/DOWN

/➝: SELECT

OK:CONFIRM SETUP:END

MANUAL SET

PR01 P-01 PR08 P-08
PR02 P-02 PR09 P-09
PR03 P-03 PR10 P-10
PR04 P-04 PR11 P-11
PR05 P-05 PR12 ---­PR06 P-06 PR13 ---­PR07 P-07 PR14 ----

PR+/-:SELECT
OK:CONFIRM SETUP:END

PR 04
RECEPTION AERIAL
AUTOSEARCH CH

_ _
FINE TUNING
NAME

_ _ _ _

MANUAL SET

PR+/-: UP/DOWN

/➝: SELECT

OK:CONFIRM SETUP:END

PR 03
RECEPTION AERIAL
AUTOSEARCH CH 03
FINE TUNING
NAME

_ _ _ _

MANUAL SET

PR+/-: UP/DOWN
0/1: CHANGE/CREATE
OK:CONFIRM SETUP:END

PR 03
RECEPTION AERIAL
AUTOSEARCH CH

_ _
FINE TUNING
NAME

_ _ _ _

Tuning

➝

➝

Tuning in New Stations

VCR Operation

If the location numbers used for programmes stored in your TV and player are different, you can change them on the
player. To do this, move the stations to the right numbers, until they are arranged the way you want.

1

1 Call the player’s "SETUP",

choose "PR PRESET" then "PR ALIGN".

2

2 Select the programme to swap.

Confirm by pressing OK button.
Move the station to the desired location number.
Confirm by pressing OK button.

1

1 Call the player’s "SETUP",

choose "PR PRESET" then "PR ERASE".

2

2 Select the station (location number) you want to clear.

Review the picture by pressing [

œœ

] button.

Clear by pressing OK button.

PR ERASE

PR+/-:SELECT

:PR VIEW

OK:ERASE SETUP:END

PR ALIGN

PR+/-:ALIGN

:PR VIEW

OK:CONFIRM SETUP:END

PR01 P-01 PR08 P-08
PR02 P-02 PR09 P-09
PR03 P-03 PR10 P-10
PR04 P-04 PR11 P-11
PR05 P-05 PR12 ---­PR06 P-06 PR13 ---­PR07 P-07 PR14 ----

PR01 P-01 PR08 P-08
PR02 P-02 PR09 P-09
PR03 P-03 PR10 P-10
PR04 P-04 PR11 P-11
PR05 P-05 PR12 ---­PR06 P-06 PR13 ---­PR07 P-07 PR14 ----

Sorting programme locations

Clearing programme locations

➝

➝

Timer Recording

VCR Operation

Call the player’s "SETUP",
choose "TIMER PROGRAM".

1

Select the programming to change or erase, press
OK.
If you want to erase this programming press button
[0].

If you wish to make changes, move to the position
you want to change using the [

œœ

or √√] buttons.

Change the settings using the [PR +/–] buttons.
If all settings are correct, press OK to confirm the

changes. Exit the menu with SETUP.

2

TIMER PROGRAM

PR START END DATE
03 21:20 22:20 12/08

01 18:10 20:30 18/08

-- -- : -- -- : -- -- / --

-- -- : -- -- : -- -- / --

-- -- : -- -- : -- -- / --

-- -- : -- -- : -- -- / --

-- -- : -- -- : -- -- / --

-- -- : -- -- : -- -- / --

PR+/-:SELECT
OK:CONFIRM SETUP:END

TIMER PROGRAM (ONCE)

PR 03
START TIME 21:20
END TIME 22:20
START DATE 12/08(SAT)
TAPE SPEED SP

0 :ERASE

/➝:CORRECT SETUP:END

Timer Review – changing and erasing

➝

More Functions

VCR Operation

Reset the counter.

COUNTER RESET

0:00:00

If you press the [PLAY] button for 5secs during stop or still mode, it goes Auto repeat mode. This player plays
repeatedly the tape from the beginning to end parts.

To release this mode, press the [ ] button or mode operation button. (PLAY, FF, REW or STOP)

Call the player’s "SETUP", choose
"VCR SETUP", then "LANGUAGE SET".

Select your language.
Confirm.

LANGUAGE SET

PR+/-:SELECT
OK:CONFIRM SETUP:END

ENGLISH
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
NEDERLANDS

Resetting the counter to zero

AUTO REPEAT

SETUP languages

Dimmer : Your player dims its display when switched to stand-by mode.
Auto power off : Your player switches to stand-by when no tape is played and no station is received for more

than 5 minutes.

Press the [ ] button for about 5 seconds.
No buttons of front panel can be operated now and LOCK INDICATOR (“ ”) will be displayed

on window display. Keep your remote control in a safe place.
To release child lock, press any button of the remote control.

Use only good quality tape cassettes with the VHS logo.

•Keep cassettes away from excessive moisture or dust, magnetic and electrical fields
(loud speakers and computer monitors, for example).

•Always wind the tape to the beginning when you have finished. Store with the full spool
at the bottom and with the cassette in its cover.

You can protect your precious recordings from being wiped by breaking out the safety tab
on the side of the cassette (some cassettes have a slide). Should you wish to re-use the
tape after removing the tab, cover the hole with adhesive tape.

PAL

Cassettes

and ...

Child lock

Connections and Copying

VCR Operation

■ If you are using a RCA cable, select the AV input on the TV to see the picture from the player.

■ If you are not using a RCA cable, select the button number on the TV reserved for video input to see

the picture from the player.

If you are not using a RCA cable, your player can transmit pictures and sound to the TV via the coax aerial cable.
Just tune the TV to the player's transmitting channel (factory set to UHF CH36). Tune the TV carefully to ensure
the best pictures and sound.

Once you have carried out the steps in "Connecting up your player with RF
lead" , switch on your TV.
Press the [ENTER] button of the player’s remote control longer than 5
seconds to call the player´s test picture.
Tune the TV to the test picture using the channel pre-set functions of your
TV as described in its manual.
When you have found the test picture, store it under the button number on
your TV for player input.
Press the [ENTER] button of the player’s remote control again longer than 5
seconds to release the test picture.

1

• If the quality of the test picture transmitted to the TV is poor due to
interference caused by a station transmitting on channel 36, you can tune
the player to a different transmitting channel.

Find a free channel between 21 and 69 on your TV.

Call the player’s "SETUP" choose "VCR SETUP" then "RF OUTPUT SET".
Type in the free channel.

Store and exit.

2

• If the quality of the test picture transmitted to the TV is poor, fine-tuning on the TV may help
(refer to the TV manual).

• Without a RCA cable, you will not get stereo sound from a TV capable of stereo sound.

To the TV via antenna cable (if you are not using a RCA cable)

RF OUTPUT SET

0-9:SELECT (21-69)
OK:CONFIRM SETUP:END

CH 36

Playing a desired scene

To move to next chapter (or track), press [√√❚ NEXT] button.

The current chapter (or track) moves to the next chapter (or track).

Press [❚œœ PREV] button.

The current scene moves to the previous chapter (or track) or first scene of current
chapter (or track).

Press the [TITLE/PBC] or [MENU] button.

A list of the titles on the disc is displayed.
* For the case of VCD disc, menu screen will

appear only when the disc has PBC function
and PBC ON is activated.

1

Press the [ENTER] button or [PLAY] button
after pressing the [œ √…†] button to
select the desired title.

For the case of VCD disc, press the [Number]
button.
The selected title now starts playing.

2

■ Some movie discs may contain multiple titles. If the disc has a movie title menu recorded on it, the [TITLE/PBC]

or [MENU] button can be used to select the movie title. Details of operation may differ depending on the disc
used.

* Selecting a title may not be available on certain DVD discs.

To skip scenes in a disc

Directly moving to a desired title

DVD Operation

Playing desired scene

DVD Operation

If you want to search with a title number or chapter
number, press the [SEARCH] button once.

- TT: Title

- CH: Chapter

1

If you want to search with a title time, press the
[SEARCH] button twice. Please enter the new title
time to be searched using the [NUMBER] button.

PLAY starts from the selected position.

3

If you want to search with a chapter number or title
number, please select TT or CH using the [ √,œ ]
button. Then enter the new chapter/title number to
be searched using the [NUMBER] buttons.

2

TT 01/02 CH /20

Searching DVD with a title number, chapter number or a time

TT 01/02 CH /20

10

TT /02 CH 10/20

01

TT 01/02 TIME

0:20:

If you want to search with a chapter time, press the
[SEARCH] button three times. Please enter the new
title time to be searched using the [NUMBER]
button.

PLAY starts from the selected position.

4

CH 04/20 TIME

0:0 :

Confirming the current PLAYING TIME

DVD Operation

While in playing, press [DISPLAY] button.

It shows the current playing time.
Each time you press [DISPLAY] button in playback mode, DISPLAY is change as below.

Confirming the current playing time of DVD disc

TITLE ELAPSED

TT 01/02 CH 01/10
0:00:57

TT 01/02 CH 01/10
0:10:05

TT 01/02 CH 01/10
0:05:56

TT 01/02 CH 01/10
1:53:25

TITLE REMAIN

CHAPTER ELAPSED

CHAPTER REMAIN

Selecting an AUDIO language and
SUBTITLE language

DVD Operation

■ The user may select an audio language and subtitle language if a disc includes Multi-language.

Keep pressing [AUDIO] button till the user’s preferred language appears in
playback mode.

If DVD disc includes audio information, every time the user presses [AUDIO] button,
English (ENG), French (FRE), Spanish (SPA) and others appear one by one.

Keep pressing [SUBTITLE] button till the user’s preferred language appears in
playback mode.

If a DVD disc includes subtitle information, every time the user presses [SUBTITLE]
button, English (ENG), French (FRE), Spanish (SPA), ... and OFF appear one by one.

A certain disc may
not support audio
select or subtitle
select.

Selecting an audio language

Selecting a subtitle language

AUDIO 1/2 : AC3 2CH ENGLISH

SUBTITLE 01/02: ENGLISH

About MP3 and JPG discs

DVD Operation

This unit will play MP3 files recorded on CD-R and CD-RW discs.

Turn on your television and select the channel assigned to this DVD player.
Press the [DVD] button and press the [OPEN/CLOSE] button, the disc tray opens.

Put a MP3 on the disc tray with the label side up.

Press the [OPEN/CLOSE] button, the disc tray closes.

The unit will take a short while to load the disc and display the directory structure.

1

The right figure appears.

2

Select the file to listen to.

Move the cursor to desired file which you want
to listen to by pressing [œ √…†] button.

Press [PLAY] or [ENTER] to start playback.

The selected file will play.

Press [■ ] to stop playback.

4

Select the folder.

Move the cursor to desired folder by pressing
[œ √…†] button and press [ENTER] button
to confirm.

3

Playing a disc containing MP3 files

00:00

■

001:003

/

Sky
Winamp

max 6

00:00

■

001:003

/

max6
Sky
Winamp

Sky

00:10 04:22 192Kbps

√

002:030

/ Sky
..

1. 01 (musicfamily.i

2. 02 (musicfamily.i

3. 03 (musicfamily.i

4. 04 (musicfamily.i

5. 05 (musicfamily.i

2. 02 (musicfamily.i

mp3
mp3
mp3
mp3
mp3

About MP3 and JPG discs

This unit will play JPG files recorded on CD-R and CD-RW discs.

Select the desired folder.

Move the cursor to the desired folder
by pressing […†] and press [ENTER]
to confirm.

1

Select the folder.

Move the cursor to desired folder by
pressing [œ √…†] button and press
[ENTER] button to confirm.

2

Select the file which you want to
view by pressing the […†] button.

3

If you press the [PLAY] or [ENTER] when a JPG image is selected, a slidshow will
begin automatically starting from the selected image.

Press [■] to stop playback.

4

00:00

■

001:003

/

CAR
ANIMAL

CAMP

00:10 04:22

■

002:125

/ CAMP

1. CAMP001

2. CAMP002

3. CAMP003

4. CAMP004

5. CAMP005

1. CAMP001

jpg
jpg
jpg
jpg
jpg

Playing a disc containing JPG (PHOTO) files

DVD Operation

Language Setup

While STOP or RESUME STOP, press [SETUP]
button.

1

Selecting a OSD language.

Select a OSD language to be displayed on DVD menus
with [ENTER].

2

Selecting Audio language.

Set your preferred audio language with [ENTER]. If
the audio language is set and recorded on the DISC,
it is automatically played in the set language every
time it is played.

OTHERS - - - - : Another language can be selected.
You can input 4-digit language code.

Refer to the language codes on next page. Press [CLEAR]
if an incorrect language code is entered.

3

Selecting Subtitle language.

Set your preferred subtitle with [ENTER]. If the
subtitle language is set and recorded on the DISC,
it is automatically played in the set language every
time it is played.

OTHERS - - - - : Another language can be selected.
You can input 4-digit language code.

Refer to the language codes on next page. Press [CLEAR]
if an incorrect language code is entered.

4

■ A user can set OSD language, Audio, Subtitle and Disc Menu.

In case a disc
does not include
setting languages
information, the
selected
language does
not appear.

“OSD” means
“On Screen
Display”.

OSD LANGUAGE
AUDIO
SUBTITLE
DISC MENU

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

OSD LANGUAGE
AUDIO
SUBTITLE
DISC MENU

ENGLISH
AUTO
OFF
AUTO

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

ENGLISH ✓
FRENCH
SPANISH
GERMAN
ITALIAN
DUTCH
PORTUGUESE
SWEDISH
CZECH

OSD LANGUAGE
AUDIO
SUBTITLE
DISC MENU

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
DUTCH
PORTUGUESE
SWEDISH
OTHERS

AUTO ✓

OSD LANGUAGE
AUDIO
SUBTITLE
DISC MENU

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
DUTCH
PORTUGUESE
AUTO
OTHERS

OTHERS ✓

OSD LANGUAGE
AUDIO
SUBTITLE
DISC MENU

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
DUTCH
PORTUGUESE
SWEDISH
OTHERS

OFF ✓

OSD LANGUAGE
AUDIO
SUBTITLE
DISC MENU

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
DUTCH
PORTUGUESE
OFF
OTHERS

OTHERS ✓

Setup

5150

Video Setup

While STOP or RESUME STOP, press [SETUP]
button.

Selecting TV Aspect.

Set your preferred TV ASPECT ratio with [ENTER]
button.

If a user selects “4:3 PS”, the user can watch
only a center of the original scene of “16:9”. If
a user selects “4:3 LB”, the user can watch the
original scene of “16:9”, but the top and
bottom of the screen look black color.
If a disc size is originally recorded in 4:3, a user
cannot watch it in a wide screen though a user
sets a size as “16:9 Wide”.

2

Selecting SCAN MODE.

You may set SCAN MODE to INTERLACED or
PROGRESSIVE.

If SCAN MODE is set to “INTERLACED”, connect
Y/Pb/Pr on the DVD+VCR to the INTERLACED
input on your TV.

If SCAN MODE is set to “PROGRESSIVE”,
connect Y/Pb/Pr on the DVD+VCR to the
PROGRESSIVE SCAN input on your TV.

3

1

■ A user can set up a connected TV condition and screen.

TV ASPECT
SCAN MODE

4:3 LB
INTERLACED

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

TV ASPECT
SCAN MODE

4:3 PS
4:3 LB

✓

16:9 WIDE

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

TV ASPECT
SCAN MODE

PROGRESSIVE

✓

INTERLACED

Setup

5352

Others Setup Features

Select character display window.

Select "On" to make OSD (On Screen Display)
language displayed in screen.

2

Select screensaver.

If bright scenes continue to be displayed in
screen, TV can be damaged. Set the screensaver
to "On", the screensaver functions
automatically and DVD logo moves continuously if
the resume stop, stop, open status is maintained
for about 5 minutes.

3

Restoring DEFAULTS.

This feature resets every function to its original
Factory Defaults except the Parental Control
settings.

4

Select Parental.

Press [√] button when the cursor is located in
PARENTAL.

Select the Parental Level using the […†]
button, and press the [ENTER] button.

These 8 levels of parental control, protect
children from watching violence, sexual scenes
and other objectionable material.

When “PASSWORD” appears on the screen,
input the password. Then press [ENTER] button.

5

While STOP or RESUME STOP, press [SETUP]
button.

1

OSD
SCREEN SAVER
DEFAULTS
PARENTAL
PASSWORD

ON
ON
RESET
8 ADULT
CHANGE

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

OSD
SCREEN SAVER
DEFAULTS
PARENTAL
PASSWORD

ON

✓

OFF

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

OSD
SCREEN SAVER
DEFAULTS
PARENTAL
PASSWORD

ON

✓

OFF

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

OSD
SCREEN SAVER
DEFAULTS
PARENTAL
PASSWORD

RESET

✓

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

OSD
SCREEN SAVER
DEFAULTS
PARENTAL
PASSWORD

8 ADULT ✓
7 NC-17
6 R
5 PG-R
4 PG-13
3 PG
2 G
1 KIDS

LANGUAGE

VIDEO

AUDIO

OTHERS

ENTER

SETUP

OSD
SCREEN SAVER
DEFAULTS
PARENTAL
PASSWORD

8 ADULT ✓
7 NC-17
6 R
5 PG-R
4 PG-13
3 PG
2 G
1 KIDS

PASSWORD

xx

OK

Setup

5554

About DVD

• DVD, Video CD (Version 1.1, 2.0), S-VCD and Audio CD
Disc type Playable Restriction

DVD Possible Region number 4 or Region number All
Video CD Possible Version 1.0/1.1/2.0, SVCD
CD Possible PCM or dts
CD-ROM Possible MP3 File
CD-R Possible Video-CD/CD/CD-ROM (MP3 File)
CD-RW Possible Video-CD/CD/CD-ROM (MP3 File)
DVD-R Possible DVD Video
DVD-RW Possible DVD Video
DVD+RW Possible DVD Video
DVD-ROM Impossible
DVD-RAM Impossible
Photo CD Possible except KODAC CD

REGION MANAGEMENT INFORMATION

This unit is designed and manufactured to respond to the Region Management information that is
recorded on a DVD disc. The region number of this player is “4”. If the region number described on the
DVD discs does not correspond to the Region number of this player, the player will not play this disc. This
player will play DVD discs made for “ALL” regions. Therefore, this player will play DVD discs marked with
labels containing the region number “4” or “ALL”.

(Region 4) (Region ALL)

4

ALL

Playable Disc

• You should record the file with standard format.

• Playback of some discs such as CD-R, CD-RW, DVD-R, DVD-RW, or DVD+RW may be impossible according to its
record status.

Other Features

5756

Other Features

• To keep a disc clean condition, please do not touch a side containing
play information.

• Do not attach a bit of paper or sticky tape on it.

• Do not expose a disc to a direct sunlight or electric heating systems.

• After using it, please keep a disc in a case.

• Before using it, please rub it from center toward outside with clean clothes.

• Do not use any type of solvent such as thinner, benzol (benzene), commercial
cleaning goods or antistatic sprays.

Handling Disc

Cleaning Disc

59

Trouble Shooting (VCR)Basic information about VCR and

• “Power On” does not work.

• It does not work even in “Power On”.

• A videotape is not inputted in.

• On inputting a videotape, the tape is
re-ejected.

• A videotape is not ejected.

• A channel on video and a play screen
does not appear.

• Noise (screen noise) appears on
screen.

• Noise appears on screen after
recording.

• While in playing, noise appears.

• Sound and screen are irregular.

• Sound comes out but screen does not
appear.

• Screen is irregular and stripes appears.

• "Screen Error" message is displayed
in a screen.

• While recording and playing, the top
of screen extremely waves.

• A screen is not clear.

• A screen at pause is trembling or slow
screen is not clear.

Checks

Symptom

➤ Please check whether a power plug is inserted in an electric outlet.
➤ Please check whether a videotape is inserted in.

➤ Try to insert a plug again.
➤ Please check whether a power plug is inserted in an electric outlet.

➤ Please check whether a videotape is in.
➤ Please check whether a videotape is inserted in a right direction (a side

of transparent window should be on the upside)

➤ Have you inputted a videotape again just after the tape was ejected?

Please try it again after fully ejecting it.

➤ When a videotape forces to be ejected, the tape may not be inputted.

In the case, please pull out an outlet, and then push the tape smoothly.

➤ That’s why a safe mode to protect a videotape is operated

automatically. Please pull out the tape and input it again.

➤ In case the product is used for a long time, a videotape may not be

ejected for a film inside may be stretched. In the case, please pull out a
power plug for about 10mins and then press “EJECT” button.

➤ Please check your antenna’s connection.
➤ TV channel should be fixed on video channel.
➤

Please check your antenna’s signal whether it may be weak. In case of its
weakness, please use a frequency amplifier connected with the device.

➤ Press “TV/VCR” and then let “VCR” is displayed on the display panel.
➤ While in no use of VCR, was it turned on?

➤ While in recording a program, do you watch another channel?
➤ Select TV by pressing [TV/VCR] button on remote control.

➤ While in playing a videotape, there may happen some noise or blot in

the part of the beginning of a videotape or resuming “PAUSE”, which
are not breakdown.

➤ Please press “TRACKING” for better screen. Videotape may be poor.

Try to change it to another one.

➤ Please use a head-cleaner to clean VCR heads. VCR heads may be

contaminated.

➤ Since VCR Play signals are not stable like a TV signals, screen may be

unstable or curved while in playing. To fix the problem, please
horizontal adjustment.

➤ In case videotape is the one recorded by other products or old one,

stripe may appear on the screen.

➤ Try to adjust the screen by [TRACKING+/-] button
➤ Try to use a head-cleaner.

➤ Try to use a head-cleaner.
➤ Try to adjust the screen by [TRACKING+/-] button.

Other Features

61

Trouble Shooting (DVD)

• The recorder does not play.

• No sound comes through.

• Blue Screen, No functions

• A disc is playing but screen does
not appear or poor screen appears.

• Sound is irregular

• REMOTE does not work.

• Dolby Digital sound does not work

• “AUDIO” or “SUBTITLE” button
does not work.

• “ANGLE” button does not work
while a DVD is playing.

• “MENU” does not appear while a
DVD is playing.

• The file name of MP3 (CD-R)
appears with strange letters.

• Any MP3 (CD-R) file isn’t displayed.

Checks

Symptom

➤ If a DVD is from overseas, it may not be played. Please check a DVD’s

region code whether it has the relative region code 4 or All.

➤ Please check whether a DVD is inserted in a right direction.
➤ If it is a CD-ROM for PC or DVD-ROM, it does not work.

➤ Play mode may be “SLOW” or “PAUSE”(In abnormal speed play, no

sound comes through)

➤ Did you connect the parts in right way?
➤ Please check the operative condition of TV or amplifier.
➤ From SETUP, please check “AUDIO” items.

➤ Progressive or interlace selected incorrectly.
➤ Press [SYSTEM] button (Refer page 51)

➤ Did you turn on your TV sets?
➤ Did you connect the parts in right way?
➤ The play may be in “PAUSE”.
➤ A disc may have some contaminants or be damaged.
➤ A disc may be bad one.

➤ Please check the connection with Dolby Digital amplifier.
➤ Please check the plugs are connected with one another tightly.
➤ Some contaminants may be remained in connection terminal.

➤ Please check the degree of remote control, distance or any interruption.
➤ Battery may be weak or exhausted.
➤ When you operate DVD, use it by pressing [DVD] button.

➤ Dolby Digital sound can be worked in the Dolby Digital amplifier only.
➤ Please check “Dolby Digital ” mark on your DVD.
➤ In case of playing it through digital output, while pressing “STOP”,

please check whether “Digital Output” is “Bitstream” by pressing
“SETUP”.

➤ Please check the connection is correct.
➤ If a DVD does not include language information, it does not support

the function.

➤ “ANGLE” is supported only in a DVD contains multi angle scenes. Also

a user can confirm the support with the “ANGLE” mark on screen.

➤ Please check the degree of remote control, distance or any interruption.
➤ Please check a battery in remote control whether it is exhausted or not.
➤ A DVD may not contain menu information.

➤ The file name of MP3 recognize only the Alphabet (A~Z, a~z), numbers

(0~9) and a special symbol on keyboard (~, !, @, #, $ ....) and 10

letters can be displayed in maximum.

➤ The letters except above case will be displayed like “----”.
➤ If the surface of disk is injured, the file display and playback can be

impossible.

Other Features

P/N:97P95600D0-AB
(1E 05/06)

SANYO Electric Co., Ltd.

Printed in Korea