Sanyo ctp x400, ctp 400a User Manual

COLOUR

TELEVISION

WITH 4 BAND RADIO &

CASSETTE

OPERATING

TAPE

INSTRUCTIONS

RECORDER

SANYO COLOUR .1
SAFETY PRECAUTION.1
POWER SUPPL Y.2—4
ANTENNA.5
CONTROLS.6
TELEVISION OPERATION.8-9

Page

~ 7

RADIO OPERATION.10
TAPE RECORDER OPERATION.11-14
COMBINED OPERATION.15
MAINTENANCE HINTS.16
TROUBLESHOOTING.17
OUTSIDE INTERFERENCE ON T.V.18
TECHNICAL DATA.19

Page

We congratulate you to the acquisition of your Colour Télévision
with 4 band radio & cassette tape recorder which has been

manufactured using the most advanced technical knowledge

available and with most modem production and testing methods.

WARNING:

To Reduce The Risk Of Fire Or Electric Shock, Do

Not Expose This Appliance To Rain Or Moisture.

To prevent electrical shock, do not remove cabinet.

High Voltage are used in the operation of the set.

This set is fully transistorized and does not contain any

user serviceable components. Refer servicing to qualified
personnel.

When the set is not to be used for an extended period
of time, it is advisable to disconnect the power cord
from the power outlet.

• TV can receive the PAL/SECAM colour System.

• Sound IF circuit of TV can receive both 5.5MHz (CCIR
countries) or 6.5MHz (01 RT countries).

• Radio can receive the 4 band of SW1/SW2/MW/FM.

• Tape recorder can use whichever tape of Normal/FeCr/
Cr02.

If you follow this manual carefully, we feel sure your
service problems will be minimized. Refer to handy
TROUBLESHOOTING on page 17.

So, please take time now to read this manual. You'll
see how easy your new set is to operate — and enjoy.

READ AND RETAIN THIS MANUAL AND THE
USAGE & SAFETY TIPS PAMPHLET INCLUDED

WITH THIS TELEVISION.

-1 -

NOTES: • We hâve developed "Automatic Voltage Se/ector"

which will set the power supp/y circuit to suit the
voltage now the TV receiver is ptuged in. The user
is no need to set the manua! voltage seiector any
more.
This Automatic Voltage Seiector is employed in
this set.

• The BATTERY CHARGE switch ® shou/d be set
to the "OPERATE"position.

• When the AC power cord is connected to the AC

POWER INPUT SOCKET (2) , the batteries are
automaticaily disconnected.

left side

EXTERNAL DC 12V (CAR BATTERY)
POWER OPERATION

NOTE: • The BATTERY CHARGE switch (J) should be set to

the "OPERATE"position.
Connect the DC power cord to the DC POWER INPUT SOCK¬
ET (3) . Plug the cigarette lighter plug of the DC power cord
into the cigarette lighter Socket.

NOTES: • Do not operate the TV set on a car battery for an

extended period.

• Long operation on the battery wi/l consume mue h
power charged in the battery and y ou may be

unable to start the car engine.

• When the DC power cord is connected to the DC

POWER INPUT SOCKET,

ce II batteries are automaticaily disconnected.

the rechargeable and dry

CHARGE

OPERATE

AC POWER OPERATION

Connect one end of the AC power cord to the AC POWER
INPUT SOCKET of the set and other end to the AC outlet.

-I-

switch ®

-2-

BATTERY POWER OPERATION
RECHARGEABLE BATTERY (OPTION)

1. Open the battery compartment lid as illustrated.

2. Ins

ert the two pin polarized plug of the Battery Pack (Model

NTP-10, optional) into the BATTERY SOCKET of the set.

BATTERY SOCKET

4. C

lose the battery compartment lid.

NOTES: • The BATTERY CHARGE switch shoulcl be set to

the "OPERATE"position.

• A fui/y charged battery will operate the set for
approximately 3

• The need for recharging the Battery Pack will be

indicated when the picture shrinks in size and does
not fill the screen. Refer to BATTERY CHECK/NG
on page 4.

• Be sure to disconnect the AC or DC power cord
from the AC or DC POWER INPUT SOCKETS of

the set when using the set from the batteries.

Battery Recharging

When the need for battery recharging is indicated, follow the

steps below.

1. Connect the AC power cord to the AC outlet.

2. Set the BATTERY CHARGE switch to the "BATT CHARGE"
position. The CHARGING INDICATOR ® will be illu¬

minât ed.
The battery will be automatically charged.

NOTES: • A complété recharge will take approximately 20

hours.

• The battery may be recharged at any time by leasing
the setplugged in whilenot in use so that the battery
will a/ways be ful/y charged and ready for portable
operation.

hours.

3. Ins

tall the Battery Pack (Model NTP-10, optional) into the

compartment. It will fit firmly by the holder as illustrated.

Left side

t

OPERATE

3

BATTERY POWER OPERATION
DRY CELL BATTERY (OPTION)

1. Open the battery compartment lid as illustrated.

BATTERY CHECKING

1. Press the POWER switch © to the "ON" (IN) position.

2. Press the DIAL LIGHT/BATTERY CHECK button ® .

3. The BATTERY INDICATOR (left VU/SOUND LIGHT
EMITTING DIODE LEVEL INDICATOR) should indicate
into the "FULL" area as shown in illustration.
If the indicatordoes not reach the "FU LL" area, the batteries
are exhausted and ail batteries must be replaced with new

ones. If Rechargeable Battery Pack (Model NTP-10, optional)
is used, recharge them.

-20 10 7

3 0 +3 -20

LEVEL

2. After inserting 10 "A-1" size flashlight batteries into the
battery sleeve (provided in the battery compartment of the
set), install it into the battery compartment as illustrated.
Be careful about the polarity of each cell.

3. Closed the battery compartment lid.

NOTES: • The BATTERY CHARGE switch should be set to

the "OPERATE"position.

• Be sure to disconnect the AC or DC power cord
from the AC or DC POWER IN PUT SOCKET of the

set when using the set from the batteries.

• Exhausted batteries may leak and damage the set

DIAL LIGHT

/BATTERY CHECK

1. Set the ANTENNA SELECT switch (D) to the "EXT" posi¬
tion. The antenna connection is équivalent to DI N 45 325 for
combined UHF/VHF antenna ® with 75 ohm Coaxial
connections.
The antenna socket (g) is placed on the right side of your set.

2. If your présent antenna produces a clear réception of black/
white pictures, then no alterations to existing antenna are

necessary.

3. A colour picture of good quality requires a higher antenna
signal than a black/white picture. If you adjust your set to a
station with a weak colour signal, your T.V. set automatically
changes to black/white reproduction.
Connect a cable with plug © from UHF/VHF antenna to

antenna socket on right side.

The telescopic antenna for UHF/VHF/FM/SW1/SW2

which

cornes with your set is designed to perform as well as any

indoor antenna and will provide an excellent picture and
Sound in areas located near the transmitter.

For best réception, it can be adjusted to virtually any posi¬
tion by extending or collapsing and/or tilting the rods. Set
the ANTENNA SELECT switch

(B)

to the "INT" position.
Adjust the antenna by varying the length and angle of the
rods until the clearest picture and sound is obtained.

In some areas it will be necessary to use an outdoor antenna.

4. For ail antenna circuit problems please consult your local
dealer.

"Snow" or a weak picture is the resuit of either a weak signal or
a poor antenna. Reflections of signais from mountains or high
buildings will cause multiple images, "Ghosts". These abnormal
conditions can be reduced to minimum by repositioning the
antenna or by installing a new one suitable for your area.

-5-

TV BAND switch

TV TUNING control (Jj)

SELECTOR BUTTON®

BILT-IN MICROPHONE

VOLUME control @

BALANCE control (ij)

TUNING INDICATOR @

-6-