Sanyo CRD-BPDV3, CRD-BPDV2 Owner's Manual

Page 2

Document No. Document Name

SANYO Electric Co., Ltd.

Revision History

(1/1)

1. Revision History

Revision No. Manager Change Description Check Approval

First Edition

Newly issued

Page 3

Document No. Document Name

SANYO Electric Co., Ltd.

Included Document List

(1/1)

2. Included Document List

Document Name Document No. Page No.

General Description

1/3 ~ 3/3 4

Dimensions, External View and
Names and Functions of Each Part

1/2 ~ 2/2 7

Terminal Description

1/3 ~ 3/3 9

Environmental Conditions

1/1 12

Reliability

1/3 ~ 3/3 13

Lot No. Reliability Description

1/1 16

Safety Standards

1/1 17

Electrical Characteristics

1/3 ~ 3/3 18

Function Description

1/3 ~ 3/3 21

Handling Manual

1/1 24

Notes for Handling

1/5 ~ 5/5 25

Page 4

Document No. Document Name

SANYO Electric Co., Ltd.

General Description

(1/3)

General Description

(1) Model Name: CRD-BPDV3
DVD-R/RW: drive with MAX ×12 speed reading, (×8) speed writing, ×4 speed rewriting.
DVD+R/RW: drive with MAX ×12 speed reading, ×8 speed writing, ×4 speed rewriting.
CD-R drive with MAX ×48 speed reading, ×48 speed writing, and ×24 rewriting)

The DVD-R/RW or DVD+R/RW feature will be selectable by the firmware.

(2) External View

External View

(3) General Specifications

1) Characteristics
* Half-height and built-in type
* Conforms to Orange Book Part 2, 3 & DVD±R/RW for general specifications.
* Equipped with the newly developed automatic strategy LSI with the data reliability

enhanced.

* DVD-R/RW drive with MAX ×12 speed reading(CAV), (×8) speed writing(PCAV),×4 speed

rewriting(CLV) DVD+R/RW drive with MAX ×12 speed reading(CAV),×8 speed
writing(PCAV), ×4speed rewriting(CLV). CD-R drive with MAX ×48 speed reading, ×48

speed writing(ZCLV), and ×24 rewriting(CLV)
* ATAPI is employed to enable high speed data transmission.
* Automatic loading mechanism
* Emergency disc ejecting function
* Data verifying function
* Media condition check function
* CD-DA read function
* Vertical operation feasible
* BURN-Proof Technology implemented

“BURN-Proof” stands for Proof against Buffer Under Run error, not for proof against burning.

* HD-BURN: a high-density writing technology
* Safe-BP: detects recording error due to irregular mechanical characteristics.
* FlexSS-BP: automatically selects the optimum recording speed for each disc.
* MRW function（CD and DVD）will support.

Page 5

Document No. Document Name

SANYO Electric Co., Ltd.

General Description

(2/3)

(4) Main Specifications

Items Specifications

Dimensions

148 (W) × 194.2 (D) × 42.3 (H) mm

Mass

1020 g

Recording Form

Orange-book part 2, 3 Fixed packet
Disc-at-once Variable packet
Track-at-once

DVD-R for general 2.0

Disc at Once Recording

Incremental Recording

Front Panel

Eject key, Emergency eject pinhole, LED (busy and write)
Headphone jack, Volume

Eject

Automatic loading

Power Supply

DC 5 × (1 ± 5 %) V DC 12 × (1 ± 10 %) V

(5) Operational environment for the “write/rewrite” application software

Items Specifications

Host Machine

IBM compatible PC (Celeron433MHz or more) (Note 1)

OS

MS-Windows 98SE/ME/2000/NT4.0/XP (Note 2)

Memory

MS-Windows 98SE/ME/NT: 128 MB or more.
MS-Windows2000/WindowsXP: 128 MB required.

256 MB recommended.

Hard disc

Empty Storage Capacity: 5GB or more (20GB or more recom mended)
Average seek time: 20 ms or less
Transmission rate: 2 MB/s or more
Do not use the HDD which calibrate thermal during operation.

CD-R (×4 ~ ×48) : MITSUI CHEMICAL , HITACHI MAXELL,

RITEK, ACER, CMC (T.B.D)

CD-RW (×4 ,×10, ×12, ×16,×24 ) :MITSUBISHI CHEMICAL, RICOH

(T.B.D) (Note 3)

Recommended Media

DVD-R(×2, ×4, ×8):MITUBISHI CHEMICAL,HITACHI MAXELL,
PIONEER VIDEO,TAIYO YUDEN,TDK

DVD-RW(×2, ×4):PIONEER VIDEO,MITUBISHI CHEMICAL
,PRINCO
DVD+R (×2.4, ×4, ×8):RICOH,MITUBISHI CHEMICAL,RITEK
DVD+RW(×2.4, ×4):RICOH,MITUBISHI CHEMICAL,RITEK

(T.B.D)

(Note 1) If any problem occurs, negotiation is required to settle the matter.
(Note 2) Windows NT4.0 doesn’t have ATAPI-DMA-Driver in the standard.
Therefore, this Drive and IDE-HDD function with PIO-Mode.
(Note 3) We intend to add the proper media one by one in the near future.

Page 6

Document No. Document Name

SANYO Electric Co., Ltd.

General Description

(3/3)

(6) Scope

This specification is applied to the CD-R/RW/DVD-R/RW,DVD+R/RW drive “CRD-BPDV3”
which is designed by SANYO Electric Co., Ltd.

(7) Contents

1) Model No. CRD-BPDV3

2) Performance Write function onto CD-R/RW/DVD-R/RW/DVD+R/RW disc in
combination with the write application software and
CD-ROM/DVD-ROM read function, in combination with the
CD-ROM/DVD-ROM application software.

3) Applications Write onto and read of the CD-R/RW/DVD-R/RW/DVD+R/RW disc.

Read of CD-ROM/DVD-ROM disc.

4) Dimensions Refer to the item “Dimensions and Dimensional Drawing”.

5) Notes for handling Refer to the Manual and Notes for Handling.

6) Others

a. The specifications of this product are the same as in the delivery specifications.

If any fault or malfunction of the product occurs when it is used under any conditions
except for our guaranteed conditions, our company has no responsibility for the claim.

b. The specifications of this product are subject to change to enhance th e performance.

c. The change of notice is issued when the specification is changed only.

d. If any doubt occurs regarding the contents of the spe cification s, nego tiation is requ ired to

settle the matter.

Page 7

Document No. Document Name

SANYO Electric Co., Ltd.

Dimensions, External View and Names and
Functions of Each Part

(1/2)

1. Dimensions and External View

(1) External View
Refer to the “General Description”.

(2) Dimensions and Dimensional Drawing
Refer to the attached document “Dimensions and Dimensional Drawing”.

(3) Names and Functions of Each Part on the Front Panel

Front Panel

1. Headphone
Terminal

: The headphone with a stereo mini plug is connected through this terminal.

2. Headphone
Volume

: The volume of the headphone connected to the headphone terminal is adjusted

using this volume di al . W he n the vol um e di al is turn ed ri ght, the vol um e b eco me s
louder.

3. BUSY
indicator

: Command executing.

ON

Reading disc, access ing condition and TOC reading condition.

OFF

Pause or Stop condition

4. WRITE
indicator

: This is ON when the data is written on to the disc.

5. EJECT key

: The disc is ejected, using this key. This key is available even when the tray is

moving. When the PRV command is transmitted from HOST or during writing,
this key is not available.

6. Emergency
eject pinhole

: If the disc is not ejected when the key is pressed, because of power failure or run

away of the software, this pinhole is used to take out the disc.

7. Disc tray

: The disc is placed on this tray.

6

7

5

1

2

4

3

Page 8

Document No. Document Name

SANYO Electric Co., Ltd.

Dimensions, External View and Names and
Functions of Each Part

(2/2)

(4) Names and Functions of Each Part on the Rear Panel

Rear Panel

1. ANALOG AUDIO
Connector

: The audio analog signal output connector.

2. CS/SL/MA Pins : By covering the jumper block, these pins are used to set the CD-R drive to

either a Master or Slave mode to work with the hard disk drive inside the
personal compute r.

Default is Master.

3. IDE Connector : Using a 40-pin connector, the ATAPI terminal of the host computer is

connected to this connector.

4. DC Connector : This is the power supply terminal.

5. FACTORY USE ONLY
Pins

: These pins are used only for the test in the factory. Don’t cover the jumper

block on them.

6. DIGITAL AUDIO
Connector

: The audio di gital signal output con nector.

7. UDMA Pins

: UDMA mode is enabled by covering the jumper block on the 2 pins of the

UDMA jumper terminals.

Default is ON.

(Note 1) In case of using some personal computes, UDMA mode need
to be disable.

1

2

3 4

6

5

7

Page 9

Document No. Document Name

SANYO Electric Co., Ltd.

Terminal Description

(1/3)

1. AUDIO Terminals

The audio signal is output through these terminals. These terminals are used when the sound
board applicable to these terminals, is attached to the personal computer.

2. Jumper Te rminals (CS/SL/MA)

SL

SLSL

SL Jumper Terminals:
To set to Slave mode, cover the jumper block on the 2 pins of the SL jumper terminals.
If the IDE controller of the personal computer supports two devices, set the CD-R drive to Slave
mode. The hard disk drive inside the personal computer is set to Master mode.

MA

MAMA

MA Jumper Terminals:
To set to Master mode, cover the jumper block on the 2 pins of the MA jumper terminals.
If the IDE controller of the personal computer supports up to four devices, set the CD-R drive to
either a Primary Slave, a Secondary Master or a Secondary Slave mode. Primary or Secondary
is set up by the IDE controller, while Master or Slave mode is set up by covering the jumper
block on the rear of the CD-R drive. The hard disk drive inside the personal computer is set to
Primary Master mode.

CS

CSCS

CS Jumper Terminals:
If the personal computer is supporting CSEL (Cable Select) signal, cover the jumper block on
the 2 pins of the CS jumper terminals and remain Slave and Master open.
An exclusive interface cable is necessary.

R-ch GND L-ch GND

Slave

Master

Use CSEL

Jumper
block

Jumper
block

Page 10

Document No. Document Name

SANYO Electric Co., Ltd.

Terminal Description

(2/3)

3. IDE Connector Terminals (ATAPI CONNECTOR)

The IDE terminal of the host computer is connected through these terminals.
Use the 40-pin IDE cable.
The pin marked “1” means pin No. 1. Connect the IDE cable of the color-coding (normally red)
on one edge to pin No. 1.

PIN NO. SIGNAL NAME PIN NO. SIGNAL NAME

2 Ground 1 RESET-
4 DD8 3 DD7
6 DD9 5 DD6

8 DD10 7 DD5
10 DD11 9 DD4
12 DD12 11 DD3
14 DD13 13 DD2
16 DD14 15 DD1
18 DD15 17 DD0
20 (keypin) 19 Ground
22 Ground 21 DMARQ
24 Ground 23 DIOW-:STOP
26 Ground 25 DIOR-:HDMARDY-

:HSTROBE

28 CSEL 27 IORDY:DDMARDY-

:DSTROBE

30 Ground 29 DMACK-
32 reserved 31 INTRQ
34 PDIAG- 33 DA1
36 DA2 35 DA0
38 CS1- 37 CS0-
40 Ground 39 DASP-

39
40

1
2

Page 11

Document No. Document Name

SANYO Electric Co., Ltd.

Terminal Description

(3/3)

4. DC Connector Terminals (DC INPUT)

The DC power supply cable is connected through these terminals.

5V

12V

GND

Page 12

Document No. Document Name

SANYO Electric Co., Ltd.

Environmental Conditions

(1/1)

Environmental Conditions

Items Environmental Conditions

Temperature

Operation : 5 °C < to < 40 °C
Storage : −30 °C < t

NO

< 60 °C

Humidity

Operation : (20 to 80) % (non-condensing)
Storage : 90 % (40 °C, 48 h)

Mean-Time-Between-Failure (MTBF)

30000 POH DUTY 20 % (read operation) (Note 1)

Life

Tray loading : 20000 cycles
Traverse mechanism : 1000000 seek

Vibration

Operation: Read 0.98 m/s2 (0.1 G) [(10 to 500) Hz]

Random Vibration

Without operation (transportation):

800 cpm (13.3 Hz), 3 mm (1.06 G), Up/Down 20
min.

Impact

Drop Impact: 490 m/s2 (50 G), 3 directions, 6 ms

(Note 1) POH : Power On Hour (live current time)

DUTY : Actual operation time

Page 13

Document No. Document Name

SANYO Electric Co., Ltd.

Reliability

(1/3)

1. Estimate Conditions

1) Standard test position
For the standard test position, the + side of the Z axis sh all be in the upper direction, provided
that the Z axis shall be the outgoing beam and th e direction of the o utgoing beam shall be +
side.

2) Standard Estimate Environments

Temperature : (22 ± 2) °C
Humidity : (50 ± 5) % RH
However, when no doubt occurs regarding the judgment, the test may be performed under the

following conditions.

Temperature : (15 to 30) °C
Humidity : (45 to 85) % RH

3) Disc to be estimated
Test Disc made by ALMEDIO Inc. ROM DISK, DA DISK, CD-R DISK (RICOH),
CD-RW (RICOH, MITSUBISHI CHEMICAL)
DVD-R/+R(RICOH,MITSUBISHI CHEMICAL)
DVD-RW/+RW(RICOH,MITSUBISHI CHEMICAL)

However, when no doubt occu rs regarding the judgment, TCD-784 made by ALMEDIO Inc.
may be used.

4) Power Supply Voltage
Power supply : DC 5 × (1 ± 5 %) V
Power supply : DC 12 × (1 ± 10 %) V

2. Reliability

The results should conform to the criteria of each item after the test has been performed under
the following conditions.
There shall be no crack, deformation or distortion from the external view of the product after
the test.
Unless otherwise specified, the measurement conditions of this test for each item shall be
subject to the above estimate conditions.
However, the temperature in this test shall be specified to the surrounding temperature of the
drive unit, rather than the surrounding temperature of the set unit where this product is
built-in.

Page 14

Document No. Document Name

SANYO Electric Co., Ltd.

Reliability

(2/3)

Test items Test conditions Criteria

1. Operating
temperature test

Operation under low temperature: +5 °C
Operation under high temperature: +40 °C
Leave the product for 4 hours without operation in the
environmental temperatures, as above. Turn on the
power and leave the product for 10 minutes.
Immediately after that, check the performance under
the same environmental temperatures as above.
However, there should be no dew condensation.

The performance should
conform to the standards
described in the Reliability
Estimation Standard
Table.

2. Practical
operation
temperature test

Operation under low temperature: +5 °C
Operation under high temperature: +40 °C
Leave the product for 4 hours without operation in the
environmental temperatures, as above. Turn on the
power of the product and leave the product for 10
minutes. Immediately after that, check the
performance under the same environmental
temperatures as above. However, there should be no
dew condensation.

There should be no errors
in the practical operation.
When this product is built
in the set unit, make sure
that the temperature does
not exceed the range
described on the left.

3. Storage test
under low
temperature.

Temperature: (−30 ± 2) °C
Leave the product for 24 hours without operation in the
above environmental temperature range, and then leave
it at normal temperature for 24 hours. After that,
measure the cha racteristic change. However, there
should be no dew condensation.

The characteristics should
conform to the standards
described in the Reliability
Estimation Standards
Table.

4. Storage test
under high
temperature

Temperature: (60 ± 2) °C
Leave the product for 24 hours without operation in the
above environmental temperature range, and then leave
it at normal temperature for 24 hours. After that,
measure the cha racteristic change. However, there
should be no dew condensation.

The characteristics should
conform to the standards
described in the Reliability
Estimation Standards
Table.

5. Storage
under high
temperature and
high humidity

Temperature and humidity: (40 ± 2) °C, (90 ± 2) % RH
Leave the product for 24 hours without operation in the
above environmental temperature range, and then leave
it at normal temperature for 24 hours. After that,
measure the cha racteristic change. However, there
should be no dew condensation.

The characteristics should
conform to the standards
described in the Reliability
Estimation Standards
Table.

6. Unit Vibration

(without

operation)

Amplitude:800 cpm (13.3 Hz)
3 mm (1.06 G)
The above amplitude is applied to the product for 20
minutes for Up/Down direction.

The characteristics should
conform to the standards
described in the Reliability
Estimation Standards
Table.

7. Unit Impact

(without

operation)

Impact: 490 m/s2 (50 G), 3 directions
Impact time: 6 ms
Measure the perform ance after applying the above
impact for each direction.

The characteristics should
conform to the standards
described in the Reliability
Estimation Standards
Table.

8. Pick-up
Slide Operation

Random Seek
After 1000000 times operation, the performance is
checked.

There should be no errors
in the practical operation.

9. Jamming When the product is built in the set unit, the level of electromagnetic wave which is

emitted from the unit shall conform to the local radio wave standards. (When any
problems occurs, the negotiation is requir ed to suppor t the c ounter measur es).

Page 15

Document No. Document Name

SANYO Electric Co., Ltd.

Reliability

(3/3)

The following table sho ws the reliability standards fo r the main parts ( units) which are used in
this product.

Test items Test conditions Criteria

10. Laser diode life

Check the recorded power after 1000 hours of
operation at 60 °C.

(except for breakage caused by static electrici ty)

The error rate should be
1 % or less.

11. Spindle motor life

Measure the current in the motor after 1000 hours
operation.

The initial value should be
+35 % or less.

12. Feeder motor life

After the pick-up slide operation as described in item
8, measure the consumption current in the motor.

The values should be
conform to the pull-out
torque 1500pps 9.8×10-

4

N-m (10grf-cm) or more.

3. Reliability Standards

The reliability standards are as follows.

1).CD

2).DVD

Items Before Test

Change in

Values after Test

Remarks

1/3 stroke mean access
time

×48 CAV

speed

0.27 s or less 0.35 s or less

Mean value measured after
reciprocating operation for (0
to 20) min. (one way value)

Items Before Test

Change in

Values after Test

Remarks

1/3 stroke mean access
time

×12 CAV

speed

0.27 s or less 0.35 s or less

Mean value measured after
reciprocating operation for (0
to 20) min. (one way value)

Page 16

Document No. Document Name

SANYO Electric Co., Ltd.

Lot No. Reliability Description

(1/1)

Lot No. Description

[Serial No. Indication]

1 2 3 4 5 6 7 8

A B C D D D D D

A. Factory: Korea Tokyo Electronics: 6,
Sanyo Media Tech: 3, SSHQ: 8

B. Year of manufactured: (1996: 6, 1997: 7, 1998: 8, 1999: 9, 2000: 0, 2001: 1,
2002: 2, 2003: 3, 2004: 4, 2005: 5)

C. Month of manufactured: Form Jan. to Sep.: 1 ~ 9 & Form Oct. to Dec.:X ~Z
(Jan: 1, Feb: 2, Mar: 3, Apr: 4, May: 5, Jun: 6, Jul: 7,
Aug:8, Sep: 9, Oct: X, Nov: Y, Dec: Z)

D. Manufacturing Serial No.: Start from 00001.
(5 digits) When the number reach to 99999, the next is 00000,
then 00001 again.

Page 17

Document No. Document Name

SANYO Electric Co., Ltd.

Safety Standards

(1/1)

Safety Standards
(1) UL (UL1950 / FDA1040)
(2) CUL (UL1950)
(3) Label

Page 20

Document No. Document Name

SANYO Electric Co., Ltd.

Electrical Characteristics

(3/3)

Application Discs

Items Specifications

CD-ROM

mode 1

CD-ROMXA (Video CD)

mode 2 form 1, mode 2 form 2

CD-DA

Applicable

Photo CD

Single session, multi-session

CD-I, CD-G, CD-TEXT

Applicable

CD Extra

2 Session
Firs t Session : CD-DA
Second Session : Data

Disc dia.

12 cm, 8 cm

Storage capacity

12 cm : 656 MB (mode 1)
748 MB (mode 2)
8 cm : 180 MB

Disc thickness

1.2 mm

Track pitch

1.6 µm

Items Specifications

DVD-R,-RW/DVD-ROM

DVD-ROM,DVD-VIDEO

DVD+R,+RW/DVD-ROM

DVD-ROM,DVD-VIDEO

Disc dia.

12 cm

Storage capacity

12 cm:4.7GB

Disc thickness

1.2 mm

Track pitch

0.74 µm

Interface

Items Specifications

Interface

ATAPI

Transfer Rate

U-DMA 33 MB/s

Connector

Item Specifications

I/O terminal (rear panel)

Power connector (+5 V, +12 V 4 P)
ATAPI terminal (40 P)
Audio out (4 P), (2 P)

Page 21

Document No. Document Name

SANYO Electric Co., Ltd.

Function Description

(1/3)

1. External View/Mechanism

(1) Tray type disc loading system

The disc is loaded on the TRAY.

(2) LED Indicator

BUSY : ON — Command executing conditions
OFF — Pausing and stop conditions
WRITE : ON — Recording condition
OFF — Others

(3) EJECT key

The disc is taken out using this key. This key is available even when the tray is moving.
However, this key is not available unde r the record ing conditio n or whe n the PRV command
is transmitted from the HOST.

(4) 8 cm/12 cm disc applicable.

The read of 8 cm and 12 cm pit discs and the write of 12 cm pit discs of the CD-R disc are
available.

2. Data read processing

(1) Read speed

The standard, CD Max ×24/DVD Max ×12 are applicable. Arbitrary speed can be set using
the ATAPI command.

(2) Read data mode (Note 1-1)

CD DVD
MODE 1 2048Byte only
MODE 2 / Form 1
MODE 2 / Form 2
CD-DA
ISRC
Media catalogue No.
Sub-codeQ R-W

(3) Audio playback

TNO playback (MSF search)
PAUSE function

(Note 1-1) Audio playback becomes possible by using the host application.

(as per ATAPI command specifications)

Page 22

Document No. Document Name

SANYO Electric Co., Ltd.

Function Description

(2/3)

3. Data write processing

(1) Write speed

i. DVD-R ×2, ×4 (CLV), (×8)(PCAV) DVD+R ×2.4, ×4 (CLV),×8(PCAV)
ii. DVD-RW ×2, ×4(CLV) DVD+RW ×2.4, ×4 (CLV)
iii. CD-R ×4, ×8, ×12, ×16,(CLV) ×16 ~ ×48 (ZCLV) write speed are applicable. ( mastering write)
iv. CD-RW ×4, ×10, ×12 (CLV), ×24(CAV) write speed are applicable.
v. HD-BURN x6,x12x,x18,x24 ( on a conversion to CD speed)

Arbitrary speed can be set using the ATAPI command.

(2) Write system

CD-R/RW DVD-RW DVD-RW DVD+R DVD+RW

Track-at-once Disc-at-once Disc-at-once Incremental

write

Random

over write

Disc-at-once Incremental

write

Incremental

write
Packet write(variable
length/fixed length)

Restricted

over write

(3) Wr ite data mode

CD-R/RW DVD±R/RW

MODE 1 CD-DA (Note 2-2) 2048Byte only
MODE 2 ISRC
MODE 2 / Form 1 Media catalogue No.
MODE 2 / Form 2 CD-TEXT
MODE 2 / Combination of Form1
and Form 2 (Note 2-1)

(4) Optimum write function

The strategy and write laser power are set automatically according to the characteristics of
the disc. This is performed when the disc is replaced or the CLV speed is changed.
In addition, the write condition is checked during writing the data, and the running OPC
function which sets the optimum laser power, is performed.

(5) BURN-Proof

BURN-Proof is a proprietary technology, which helps the users to protect from Buffer Under
Run Error.

(Note 2-1) This is applicable only within the approved range of the CD-ROM and CD-ROM XA.

(Note 2-2) Host computer makes and transfers the RAW data which includes pre-gap in the

case of the disc-at-once writing. At this time, the track management information
needs to provide instructions to transfer the start and end address of the actual audio
data portion.

Page 23

Document No. Document Name

SANYO Electric Co., Ltd.

Function Description

(3/3)

4. Servo/access

(1) Servo Aut omatic Adjustment

When the disc is loaded, the focus, tracking offset and servo gai n are adjusted automatically.

(2) Sled Control using the Stepping Motor Driving

The mechanisms and circuits related to the sled are simplified. The micro step operation is
controlled using the micro computer when the access-time-specific trapezoidal driving occurs
and the read/write operation is performed.

(3) High speed access using the learning function

The number of tracks calculated from the CLV speed and pick-up position are corrected so
that the disc program area is kept at the access time accompanied with the travel of the sled.
Then, the corrected number of tracks is stored and the final number of tracks on the disc are
calculated in order to reduce the number of seeks．

5. Other Functions

(1) Multi-volume applicable

To switch the sessions, the SESSION SELECTOR is used.

(2) Disc identification codes

The discs produced by each manufacturer are identified using the disc identification codes
prepared by the Orange Society for the Research. This is referred to when the laser power
and strategy are decided, when the writing operation is performed.

(3) Device type

Device type is 05 (CD-ROM) only.

6. CRD-BPDV3 Interface

The host computer interface of the CR D-BPDV3 conforms to the ATAPI.

7. BURN-Proof

In some case of disc condition, an error may happen by the failer of BURN-Proof function

because it controls previous recorded data and new recording data by the advanced signal
management system. In addition to the stated above, a BURN-Proof function also does not work
correctly due to the unexpected accident like a power cut and a malfunction of PC and so forth.

8. SHOCK-BP

Please refer to the latest information on the web: www.burn-proof.com.

9. Safe-BP

Please refer to the latest information on the web: www.burn-proof.com.

10. HD-BURN
Please refer to the latest information on the web: www.burn-proof.com.

Page 24

Document No. Document Name

SANYO Electric Co., Ltd.

Handling Manual

(1/1)

(1) How to use

Before using this product, make sure that the d evice driv er for th e Combo driv er is installed in
the personal computer.

1) How to insert the disc.
i. Turn on the power of the main machine where the product is attached.
ii. Press the eject key to open the disc tray.
iii. Place the disc on the tray so that the printed side is upside.
iv. Press the eject key to close the disc tray.
v. Read the disc. The read indicator goes on-and-off during the TOC read operation. Then

the indicator goes on.
Write the data onto the disc. The write indicator goes on while the data is written.

2) How to take out the disc.
i. Make sure that each indicator is OFF.
ii. Press the eject key to open the disc tray.
iii. Take out the disc.
iv. Press the eject key to close the disc tray.

3) How to take out the disc in an emergency.
When the disc can't be ejected because of power failure or run-away of the software, take the
following measures to force the take out of the disc.
i. Prepare a steel paper clip. Extend the paper clip .
ii. Insert the end of the paper clip into the emergency eject hole and press it strongly to eject

the disc tray.
iii. Pull the disc tray toward you and take out the disc.
Push back the disc tray.

(2) Product ID, Vender ID

Product ID: CRD-BPDV3, Vender ID: GENERIC

Page 25

Document No. Document Name

SANYO Electric Co., Ltd.

Notes for Handling

(1/5)

1. Don't look at the laser beam.
Don't look at the laser beam source.
If the laser beam hits your eyes, it might cause damage to your eyes.

2. Don't use deformed or cracked CDs and DVDs.
Don't use cracked, deformed CDs and DVDs or repaired CDs and DVDs with adhesives. As the

disc turns with high speed within the product, broken pieces might scatter and hurt you.

3. Don't touch the inside components of this product.
Don't disassemble or modify this product. It might cause the breakdown of this product.

4. Don't touch the connector parts.
If you touch the connector parts of this product, it might cause a contact fault or breakdown

because of the oil from your hands or static electricity. Also, don't touch the connector part on
the personal computer when this product is connected or disconnected.

5. Don't connect and disconnect this product excessively.
When this product is connected and disconnected repeatedly, the connector part becomes

heavily loaded and this might cause the breakdown of this product. Don't connect and
disconnect this product excessively, except for necessary cases.

6. How to prevent the breakdown
(1) Don't impact or vibrate this product.
(2) Keep the product where no fluid or alien substances can enter into this product.
(3) Don't use this product on an incline.
(4) Don't move this product with the disc inside.

7. Installation Place

Avoid t h e following places for using this product.

(1) Places of high temperature or grea te changes in temperature.
(2) Places where sunlight can hit the product directly.
(3) Places with strong vibrations.
(4) Places with uneven surfaces.

Page 26

Document No. Document Name

SANYO Electric Co., Ltd.

Notes for Handling

(2/5)

8. Maintenance
(1) The dirt on this product should be cleaned off lightly with a soft cloth with some water or

diluted neutral detergent.

(2) Make sure not to use volatile chemicals such as benzine and thinner, because they might

cause deformation and color change of the product.

9. Notes for the Handling of the Disc.
(1) When you carry the disc, don’t touch the side where no letters are printed.
(2) Don't write letters on the disc or attach paper or a seal.
(3) Dust or finger prints on the side without any printing should be cleaned off by a soft cloth.
(4) When the disc is cleaned, always clean from the center to the outer rim.
(5) Don't use benzine, thinner, cleaner for analog LP or a static electricity preventing agent,

because these might cause damage to the disc.

(6) Keep the discs in the disc case. Don't put the disc in a place where sunlight can hit directly

or the temperature increases.

10. It is prohibited from copy ing, selling and transf ering datas and pro grams that are protecte d by
the copyright to the authorities without permission.

However, personal use of the sound and images that are recorded with this product is

permitted.

11. Application

The following applications may be supported by this product, in future.
(Therefore, we are not responsible for any defects or damages using other applications. Also,

some version no. of above Applications may not recognize the drive. Please contact to the
Application maker.)

Software DVD Player: WinDVD (InterVideo Inc.), PowerDVD
Software writing Storage: NERO Version5 (AHEAD)， B’sRecorderGold(BHA)
, Software DVD Video Recording: DVD it!,(Sonic Solutions), NEO DVD(Medio Streams)

12. Drive Mount

This drive has holes fo r heat radiation at top cabinet and side cabinet. Please do not fill the se

ventilation holes.

Please avoid any components from these ventilation holes over 5mm in order to keep

circulation.

13.Recommend to use the JIS standard disc what is described the CD Logo XXX marking on the

surface of disc label side.
We do not guarantee the play-back function if the out of CD standard disc is inserted. Even if
it can be played, the sound qualities are not guaranteed.

Page 27

Document No. Document Name

SANYO Electric Co., Ltd.

Notes for Handling

(3/5)

Dimensions

The following items should be considered when enclosure chassis for this drive is designed.

1. Over 5 mm space should needed between top of drive and enclosure chassis.

2. Don’t press the production label even if there are any reasons.

Page 28

Document No. Document Name

SANYO Electric Co., Ltd.

Notes for Handling

(4/5)

Package

Page 29

Document No. Document Name

SANYO Electric Co., Ltd.

Notes for Handling

(5/5)

Package Configuration

GROSS WEIGHT 12 kg

300 unit 1 pallet: 6 box × 5 stack (30 box)
Pallets are to be banded and stretch-wrapped.
Corner strips are attached.