Sanyo CP14SE1, CA21SE1, CA14SE1, CP21SE1 Instruction Manual

Colour Television

INSTRUCTION MANUAL

CP14SE1
CA14SE1
CP21SE1
CA21SE1

Multi System
CATV Hyper Band
256 Programmes with Automatic Tuning
AV Stereo Sound System (Optional Models)

If the televi­sion is to be
built into a
compartment
or similarly
enclosed, the
minimum dis­tances must

be maintained.
Heat build-up can reduce the service life of your televi­sion, and can also be dangerous.

2

WWararning and Caution

ning and Caution

Never stand on, lean on or push sud­denly the television or its stand.
You should pay special attention to
children. Serious injury may result if
it should fall.

Do not place your television on an
unstable cart, stand, shelf or table.
Serious injury to an individual, and
damage to the television, may result
if it should fall.

High voltages are used in the operation of this television receiver. Do not remove the
cabinet back from your set. Refer servicing to qualified service personnel.

To prevent fire or electrical shock hazard, do not expose the television receiver to rain
or moisture.

Do not drop or push objects into the television cabinet slots or openings. Never spill
any kind of liquid on the television receiver.

When the television receiver is
not used for an extended period
of time, it is advisable to discon­nect the AC power cord from the
AC outlet.

Avoid exposing the television
receiver to direct sunlight and
other source of the heat.
Do not stand the television
receiver directly on other prod­ucts which give off heat. E.g.
video cassette players, audio
amplifiers.

Do not block the ventilation holes in
the back cover.
Adequate ventilation is essential to
prevent failure of electrical compo­nents.

Do not squash power supply
cord under the television
receiver.

Minimum distances

Warning

Caution

20cm

10cm

10cm

5cm

3

Remote Contr

Remote Contr

ol / Aerial Connection

ol / Aerial Connection

Remote Control Operation

Standby/Power

-on

To switch the TV on and off. For shutting off a power supply completely, Press the Mains ON/OFF button

on the front control of TV set.

Sound mute

To switch the sound from the speakers. The sound changes as follows; normal -> mute

TIMER

T

imer

To Adjust Timer function OFF-TIMER -> ON TIMER -> ON PROGRAM
Recall/Colour system selector

To display the programme information on the screen.
It also operates as Colour system selector if the clear picture cannot be obtained even when the broad­casting or AV signal is received.
Colour System and Sound System (SIF) could be changed in SEMI -AUTO and MANUAL TUNING oper­ation.

-/- --/- -

Direct programme selector

For direct access to programmes using the (0-9) numeric button. For selection of analogue programme

position 10 - 255, Example: for programme position 17,

Press

the Digit button

“1”button. Press “7”

button. For programme position 125

Press the Digit button twice. Press “2”button. Press “5” button.

For programme position

225

Press the Digit button 3 times. Press “2” button. Press “5”button.

P

P

Alternate

To select the previous position and the present position.

-/- -

Volume Up/Down

To adjust the sound volume level . Also operates as left ( ) and right ( ) cursor.

-/- -

-/- -

Programme down/up

To select the next programme number or previous programme number. Also operates as up ( ) and
down ( ) cursor.

-/- -

SWAP

Swap

To swap the channels between two stored programme positions

SOUND

This button is not used

-/- -

A•B

Stereo/Mono (optional models)

To select mono or stereo sound in AV mode.

PICTURE

Picture Mode

To select Picture mode; PERSONAL, DYNAMIC, NATURAL, ECO, GAME.

-/- -

BASS

Bass Expander (optional models)

To activate bass expander function.

S. SYS

Sound System

To select optimum sound system (BG → I → DK → M).

SURROUND

Surround (optional models)

To activate Surround function.

MENU

Menu

To Call up the TV MENU.

Connect the cable with a plug from a UHF (or VHF) aerial to the aerial socket on the cabinet back.

For all aerial circuit problems please consult your local dealer

.

Aerial Connection

CH

CH

4

Contr

Contr

ol Panel / Plug and Play / T

ol Panel / Plug and Play / T

imer

imer

Control Panel

Plug & Play

This TV set provides a self-automatic tuning system function called “Plug & Play”. It automatically begins searching

and storing of all available channels when switching-on the TV set for the first time.

1

1 Press the Power ON/OFF button to turn the TV on, and the TV set will search and store of all available TV channels

automatically.

2

2 Press the MENU button after completing Plug & Play to return to the normal TV mode.

✐ This procedure only appears at the first switch-on time.

Auto Shut-Of

f function

This TV set changes to the standby mode within 10 minutes after all broadcasts have ended.

■ The OFF TIMER cancels when the TV set is turned

off or if a power failure occurs.

The OFF TIMER will switch off the TV automatically after
30 minutes, 1 hour, 1 hour and 30 minutes, or 2 hours.

1

Press the TIMER button.

2

Press the VOLUME ( + or - ) button to select the

time period.

OFF 0:00

■ Just one minute before switching off the TV,

“OFF 0:01” will be display on the screen.

■ To cancel the OFF TIMER, select “OFF 0:00” by

pressing the VOLUME (+ or - ) button.

Timer

OFF-TIMER

Mains ON/OFF button

Remote Control Detector

Stand-by and Power Indicator

Audio Input Jack

Video Input Jack

VOLUME

TV/AV Selector

MENU

Programme UP/DOWN

Monaural Model

Mains ON/OFF button

Remote Control Detector

Stand-by and Power Indicator

Audio Input Jack (Right)(AV2)

Audio Input Jack (Left) (AV2)

VOLUME

TV/AV Selector

MENU

Programme UP/DOWN

AV Stereo Model

Video Input Jack (AV2)

TV

V

I

DE

O

A

UD

/

AV

M

ENU

-

I

O

+

CH

P

O

W

E

R

-A

UDIO

-R

TV

/

AV

M

ENU

­+

CH

P

O

W

E

R

V

I

DE

O

L

5

Timer

ON-TIMER

When the ON TIMER is set. TV will automatically be switched on to the selected programme position when the specified
time has elapsed.

1

Press the TIMER button twice. Press the VOLUME ( + or - ) button. The set time will be increased or decreased

by 10 minutes each time the button is pressed ; the maximum time which can be set is 24 hours.

■ If no operation is performed after the TV has been switched on by the ON TIMER, such as if you are not at home,

the TV will be automatically switched off after approximately 2 hours.

■ If the TV is already switched on when the time set for the ON TIMER has been reached, only the programme position

will be changed to the set programme position.

■ Cancelling ON TIMER. To cancel the ON TIMER, press the VOLUME ( + or - ) button to set it to “ON 0:00” while the

ON TIMER screen is shown. Switching off the TV by pressing the Mains ON/OFF button will also cancel the ON

TIMER settings.

2

Use Direct programme Selection to insert programme position for when TV is switched on by ON TIMER.

TTimer / Pictur

imer / Pictur

e Adjustment

e Adjustment

Picture Adjustments

Picture Menu Operation

1

Press the MENU button for MAIN menu

display.

Approximately five seconds after you release the VOLUME
(+ / -) button, the screen display switches from the adjust-

ment screen to the normal TV screen.

2

When “PICTURE” is not selected, select “PICTURE”

with the Programme UP or DOWN button.

4

Select desired control by pressing the Programme
UP or DOWN button.

3

Press the VOLUME + or

-

button to display Picture

Adjustment menu.

5

Press the VOLUME + or

-

button to alter

settings.

■ To return to Main menu, press the

ALTERNATE button.

■ To return to the normal TV mode, press the

MENU button. ( Or will automatically return to

the normal TV mode after 20 seconds.)

(MAIN MENU)

WHITE TONE : Adjusts white balance.
FINE TUNING : Fine tuning in case of weak broadcast

signal or poor reception. Only displayed in TV mode. Will
not be displayed in AV mode.

The 2nd page is not displayed when there is no TINT
adjustment.

Page 1

Page 2

Picture Adjustment Item
COLOUR : Adjusts colour intensity.
BRIGHT : Adjusts picture brightness.
CONTRAST : Adjusts picture contrast.
TINT : Adjust colour tints. (Displayed only on

NTSC or NTSC4.43 system signal reception.)

SHARPNESS : Adjusts picture detail.

(Monaural Model

MAIN MENU)

PICTURE

PRESET
LANGUAGE

P

P

SELECT ENTER

PICTURE

AUDIO
PRESET
LANGUAGE

SELECT ENTER

COLOUR

BRIGHT
CONTRAST
TINT
SHARPNESS

SELECT ADJUST BACK

BACK

M

EXIT

M

EXIT

WHITE TONE

FINE TUNING

P

P

M

EXIT

SELECT ADJUST BACK

P

P

M

EXIT

6

Semi-Auto Tuning and Manual Tuning

1

Press the MENU button for MAIN menu display.

2

Select “PRESET” by pressing the Programme UP or
DOWN button.

3

Press the VOLUME + or

-

button for PRESET menu

display. On entering RESET display, Automatic Tuning

will be selected initially.

4

Select “SEMI” or “MANUAL” by pressing the VOLUME +

or

-

button.

5

Select “SEARCH” by pressing the Programme UP or
DOWN button.

Semi-Auto Tuning:
Press and release the VOLUME + or

-

button to
search for required TV station. Once a station is
located, tuning will automatically stop. Continue till
desired channel is located.

Manual Tuning :
Press and hold the VOLUME + or

-

button to

search for required TV station.

Sound Adjustments / T

Sound Adjustments / T

uning of the Channels

uning of the Channels

Sound Adjustments

Sound Menu Operation

1

Press the MENU button for MAIN menu display.

2

Select “PRESET” by pressing the Programme UP or
DOWN button.

3

Press the VOLUME + or

-

button for PRESET menu

display. On entering PRESET display, Automatic

Tuning will be selected initially.

■ The Automatic Tuning operation can be cancelled at

any time by pressing the Programme UP or DOWN

button.

4

Select “SEARCH” by pressing the Programme UP or
DOWN button

.

After all receivable channels have been found and stored,
the TV set automatically returns to programme position
“1”.

5

Press the VOLUME (+) button to start channel tuning.

Tuning of the Channels

Automatic Tuning

MENU

CH

CH

1

Monaural Models are not equip with Audio Adjustment Menu

Audio Adjustment Item

BASS : Bass Adjustment
TREBLE :Treble Adjustment
BALANCE : Left/right speaker volume balance adjustment
BASS EXPANDER : Operates BASS EXPANDER on and

off

SURROUND :Operates SURROUND on and off.
Note: When the stereo signal is inputted from the right and

left audio input terminals in the AV mode, surround mode is

changed as follows; “SURROUND” ON and “SURROUND

OFF”.

1

Press the MENU button for MAIN menu display.

2

Select “AUDIO “ by pressing the Programme UP or

DOWN button.

3

Press the VOLUME + or

-

button for Audio

Adjustment menu display.

■ To return to Main menu, press the ALTERNATE button.

■ To return to normal TV mode, press the MENU button.

(Or will automatically return to normal TV mode after 20
seconds.)

Audio Adjustment Operation

BASS

TREBLE
BALANCE
BASS EXPANDER OFF
SURROUND OFF

MODE

SEARCH

POSITION
SYSTEM
SIF

AUTO

START

AUTO
BG

6

PICTURE

AUDIO
PRESET
LANGUAGE

MODE

SEARCH
POSITION
SYSTEM
SIF

AUTO

START

6
AUTO
BG

MODE

SEARCH

POSITION
SYSTEM

MODE

SEARCH

POSITION

AUTO

START

6

AUTO

SEMI

6

7

TTuning of the Channels / Private Position

uning of the Channels / Private Position

8

Press the MENU button to return to normal TV display.

7

Once desired channel is located, select “MEMORY” by

pressing the Programme UP or DOWN button.

The VOLUME + button will move tuning toward the
higher frequencies, and the VOLUME

-

button will

move tuning toward the lower frequencies.

6

Press the VOLUME + or

-

button to enter the desired

channel into Programme Position 6.

To pre-set other Programme Positions, repeat steps 5-8.

SYSTEM

AUTO

Channels Swapping

Use this channel swapping feature to swap the channels
between two stored programme position. This feature is par­ticularly useful after automatic tuning.

1

Select programme position “6”.

2

Press the SWAP button.

For example, to swap the channel between programme
position “6” and programme position “12”.

SWAP 6 AND

-

The two TV channels will now have changed
places.

3

Press the DIGIT button, “ 1 “ button and then “ 2 ”

button on the remote control to enter programme
number 12. (For example, to enter programme

number “ 3 “, press “ 3 ” button only. )

4

Press the SWAP button.

SWAP 6 AND 12

1

Enter to SEMI-AUTO or MANUAL tuning mode.

2

Select “POSITION” with the Programme UP or
DOWN button.

When there is a position you do not use, Position 4 for
example, by setting the SKIP Channel function it is possi­ble to jump over this position, when you are selecting a

channel using the Programme UP/DOWN or CHANNEL

SCAN button.

For example, to set programme position “4” as Skip
channel ;

3

Press remote control “4” button to select Programme
Position 4. Use the DIGIT button and Programme

Selector (Number buttons) to enter Programme
Number. Do not use the VOLUME + or

-

button to

enter programme position in this settings.

Skip Channel Set and Cancel

6

Press the MENU button to return to normal TV display.

4

Select “SKIP” by pressing the Programme UP or

DOWN button, then press the VOLUME + or

-

button to set SKIP to ON. To cancel Skip Channel
function, set to OFF.

5

Select “MEMORY” by pressing the Programme UP
or DOWN button, then press the VOLUME + or

-

button for memory.

Any number of channels maybe set as Skip Channels.

POSITION

4

For example, to set the programme position “15” as
the private position.

1

Select programme position “15”.

2

Press and hold the RECALL/COLOUR SYSTEM

button for more than 2 seconds.

The programme number “15” will shift to centre of the
screen.

The picture will disappear, and “ 15” will be display on
the screen.

3

Press the MENU button.

Private position is used to restrict of programme
positions that you do not want others to watch. Any
position can be set as the Private position.

15

AUTO

BG

15

15

AUTO

BG

How to Set the Private Position

Private Position

MODE

SEARCH

POSITION
SYSTEM

SIF
SKIP

MEMORY

SELECT ADJUST BACK

MANUAL

6

AUTO

BG
OFF

OK

P

P

M

EXIT

SYSTEM
SIF

SKIP

AUTO
BG

ON

8

Private Position / On Scr

Private Position / On Scr

een Display Language /

een Display Language / Connecting other Equipment

2

Press and hold the RECALL/COLOUR SYSTEM

button for more than 2 seconds.

3

Press the RECALL/COLOUR SYSTEM

button for watching a TV programme.

Note: The position “15” is still in the private position.

The private position is now cancelled.

1

Select private position (position “15”).

2

Press and hold the RECALL/COLOUR SYSTEM

button for more than 2 seconds.

3

Press the MENU button.

15

15

Private Position

To View a Programme on Private Position

1

Select private position (In this case position “15”).

Cancelling of the Private Position

1

Press the MENU button for MAIN menu display.

2

Select “LANGUAGE “ by pressing the Programme
UP or DOWN button.

3

Press the VOLUME + or

-

button for Language

menu display.

Select “ENGLISH”, “ ”, “VIETNAMESE”,
“ ”, “FRANÇAIS”, “INDONESIA” by press-

ing the

Programme

UP or DOWN button. To return to

the normal TV mode, press the MENU button.

4

Press the MENU button to return to normal TV

display.

On Screen Display Language

Connecting other Equipment

■ When a stereo video recorder is connected to the TV

set, make sure the audio output terminals are correctly
connected to the corresponding L (left) and R (right)
audio input terminals.

■ When a monophonic video recorder is connected to this

product, connect the audio output terminal of the video
recorder to the L(left) audio input terminal of the TV set.

■ To make sure the colour system of the TV set is

consistent with the signal of your video recorder, if
necessary, select a matching system. The colour
system set in AV mode can be stored automatically.

■ When an AV program (from a video recorder or a

DVD player) is played, you may return to TV mode by
selecting any of the TV position.

■ To watch video input picture, select AV1 position (AV

position for monaural models) by pressing the TV/AV
Selector.

Connecting to the Rear AV1 Input Jacks

Connecting to a Monophonic Video Recorder (AV1)

When the audio signal from the VCR is stereo, be sure to
connect the right and left channels to the respective right
and left AUDIO IN terminals. Then select “STEREO”
channel of the audio channel in the TV set with the
remote control button.

Note for monaural models: the Stereo/Mono button is

no function.

A B

Note: The effect of surround is not obtained although the

switching of surround is displayed in this monaural con­nection.

When the stereo signal is inputted from the right and left

audio input terminals, each time the SURROUND button

is pressed (or selection of On-screen Menu), surround

mode is changed as follows; “ SURROUND ON” and
“SURROUND OFF”.
Note for monaural models: the surround button is no

function.

Note: For monau-

ral model TV there
is no L/R audio
input terminals. If
the video player is
stereo, connect
the Left (L) audio
output terminal
from video player
to audio input ter­minal on the mon­aural TV set (more
details see your
video player man­ual book).

y

P

C

C

NN

R

(MONO)

L

MONITOR OUT

R

L

V
I
D
E
O

INPUT

AV1/DVD

C

To Audio Input-R (AV1)

To Audio Input-L (AV1)

To Video Input (AV1)

R

C

B

Y

VIDEO

Video/DVD Player

9

Connecting other Equipment

Connect the component output terminal on your DVD play­er to the component video input terminal of this product.
(NOTE: When a signal of Y,Cb,Cr/Y,Pb,Pr is received, the
output signal from monitor output terminal will be corre­sponding but without colour (black and white image).)

Connecting to a DVD Player with AV1
(DVD) Video Component Output Terminal
(Y, Cb or Cr) (optional models)

28

AV1 AV1(DVD)

(TV mode)

AV2

(Optional model)

In this connection status, whenever the TV/AV button is
pressed, the mode will change as follows:

■ Make sure the component video terminal (Y, Cb or Cr)

is connected correctly.

■ To watch a program in this connection status, select

AV1(DVD).

It is convenient to use the AV input jack on the front panel
for equipment that is often connected and disconnected.

Connecting to the Front AV2 Input Jacks

■ To watch the Front video

input picture, select AV2 (AV
position for monaural
models) position by pressing

the TV/AV Selector.

Note: For Monaural models

Do not connect external equip­ment to both rear and front AV
input jacks to avoid signal mix
and distorted picture.

The picture signal being displayed on the TV screen is out­put through the Monitor Output Jacks. Use these terminals
to record TV broadcasts and for video dubbing from AV1
or AV2 input terminals.

■ To dub video from the AV1 terminal input, select AV1

position and (for Monaural models select AV position)

by pressing the TV/AV Selector.

■ To record TV programme, select TV mode by

pressing the TV/AV Selector and record the desired

programme.

TV mode

AV1

15

AV

Monaural
models

Connecting to the Monitor Output Jacks

To video and

audio inputs

Connecting to AV Device with TV
Antenna Jack

AV Device

Antenna Jack

PLAY

AV device can be connected to the antenna jack of the
TV set.

To watch programs input from the antenna jack, operate
as follows:
(1) Start on the AV device to play the program.
(2) Select the channel position desired, and start manua

tuning.

See instruction manuals of the relevant AV devices for
details of connection and adjustment.

MONITOR OUT

R

To Audio Input-R (AV1)

(MONO)

L

To Audio Input-L (AV1)

R

L

V
I
D
E

O

To Input Terminal C

To Input Terminal CB

To Input Terminal Y

INPUT

AV1/DVD

C

R

R

C

B

Y

VIDEO

VIDEO

R

(MONO)

L

MONITOR OUT

R

L

V
I
D
E

O

To Audio Output-R

To Audio Output-L

To Video Output

INPUT

AV1/DVD

C

R

C

B

Y

VCR for Recording

Video/DVD Player

To Video Input (AV2)

To Audio Input-L (AV2)

To Audio Input-R (AV2)

Video/DVD Player

■ NO PICTURE, NO SOUND

● Check if TV is plugged in.

● Try a different channel, if OK, probably station trouble.

■ POOR PICTURE, SOUND OK

● Adjust BRIGHTNESS control.

● Adjust FINE TUNING control.

● Check aerial connections

■ NO COLOUR, PICTURE OK

● Adjust COLOUR control.

● Adjust FINE TUNING control.

● Is the programme in colour ?

■ WEAK PICTURE

● Check aerial connections on back of set.

● Check aerial for broken wires.

● Re-orient aerial.

■ The following faults are not caused by the

receiver:

"GHOSTS"

Reflections of signals from mountains or high build­ings will cause multiple images, called "Ghosts".
These abnormal conditions can be reduced to mini­mum by repositioning aerial or by installing a new one
suited for your area.

"INTERFERENCE"

Interference may be caused by electrical appliances,
car ignition systems, etc. This should normally be a
temporary condition, but should this interference per­sist, contact your dealer.

Power Source AC220-240 Volts, 50/60Hz

Colour System PAL/NTSC4.43/NTSC/PAL-60Hz

Sound System B/G, I, D/KK’, M/M

Channel Coverage

VHF: E2-E12, A2-A13, R1-R12, J1-J12, K1-K9

0-11, 5A (AUS), 1-11 (NZ)

UHF: 21-69, A14-A69, J13-J62,

28-69 (AUS)

CATV: S1-S41, X, Y, Z, Z+1, Z+2

Aerial input impedance 75 Ω

Audio output (RMS) : 5 W + 5 W (All Models)

Speakers : 5 x 9 cm x 2 pcs (All Models)

Ext. terminals

DVD Video Component: Composite/Component Y,
CB,CR input (Optional Models)
Video inputs: Phone Jack x 2 (1.0Vp-p, impedance 75Ω)
Audio inputs: Phone Jack x 2 (436mVrms, impedance
more than 40KΩ)
Video monitor outputs: Phone Jack x 1 (1.0Vp-p,
impedance 75 Ω)
Audio monitor outputs: Phone Jack x 1 (436mVrms,
impedance less than 600Ω)

Dimension

Model CP14SE1, CA14SE1:
433 (W) x 336 (H) x 353 (D)mm
Model CP21SE1, CA21SE1:
580 (W) x 460 (H) x 457 (D)mm

Weight

Model CP14SE1, CA14SE1: approx. 8.7 Kg
Model CP21SE1, CA21SE1: approx. 18.7 Kg

Specifications subject to change without notice.

Specifications

Helpful Hints

Care and Cleaning / Specifications / Helpful Hints

Care and Cleaning

The surface of the cabinet can be damaged if not properly maintained. Many common household aerosol sprays, clean­ing agents, solvents and polishes will cause permanent damage to the fine surface.

1. Unplug the power cord before cleaning the Television.

2. Clean the screen with a soft cloth dampened with glass cleaner or warm water.

3. Clean the cabinet with a soft cloth dampened with a mild household detergent and warm water. Dry

thoroughly.

Note: NEVER spray liquids on the screen because they can run down and drip onto the chassis. This may cause com-

ponent failure not covered under Warranty.

10

11

Memo

SANYO ELECTRIC Co., Ltd.

Part No. 1AA6P1PXXXX-- BB2V (AC6-A1)