Sanyo CLT-9922, CLT-9935, CLT-9925 User Manual
CLT-9922
CLT-9925
CLT-9935
900-MHz
Cordless Telephone
with Caller ID
INSTRUCTION
MANUAL
SANYO Canada Inc.
www.sanyocanada.com
IMPORTANT
Charge the handset battery for 12 continuous
hours prior to first use.
INTRODUCTION
Congratulations on your purchase of this Sanyo cordless telephone.
Your Sanyo 900-MHz cordless telephone is a fine-quality home communications
product. It is carefully designed and produced by a world leader of consumer and
industrial electronics equipment. With proper maintenance and care, it will provide
you with years of enjoyment and convenience.
Main Features
900-MHz Technology
Extended Range -The use of 900-MHz frequency band for signal transmission
between base and handset means greater communication range compared to
conventional 43 – 49 MHz cordless telephones.
Ultra-Low Noise -The high frequency communication has also significantly reduced
noise level.
40-Channel Auto/Manual Scan -Your new telephone uses one of 40 channels in the
900-MHz frequency band. It automatically selects a clear channel every time you
receive or place a call on the handset.
COMPANDER PLUS Noise Reduction
This fourth generation of the Sanyo’s original noise reduction technology now
filters out more background noise.
• Caller ID* and Caller ID with Call Waiting*.
(*Each feature works with your telephone company. A subscription is required.)
• 40-number Caller ID list
• 10-name/number directory
• Lighted keypad (CLT-9935 only)
• 3-line trilingual display
• Ringer on/off switch
•Wall-mountable
• Belt clip (CLT-9925 and 9935 only)
*Important:
To use all of the features of this phone, you must subscribe to either the standard Name/Number Caller ID Service
or Caller ID with Call Waiting Service. To know who is calling while you are on the phone, you must subscribe to
Caller ID with Call Waiting Service.
GETTING STARTED
Checking the package contents
Make sure your package includes the items shown here.
INSTALLATION
Modular jack
To properly connect your phone to your telephone lines, you will need an RJ11 type
modular phone jack. If you do not have a modular jack, call your local phone
company to find out how to get one installed.
Installation note: Avoid places near electrical equipment such as refrigerators,
computers, TVs or fluorescent lamps. These may cause interference or reduce the
operating range of the cordless telephone.
Connections
1. Set the RINGER switch on the front of the handset to
ON and place the handset
in the base.
2. Plug the AC adaptor into the
POWER 9V DC jack on the bottom of the base and
the other end into an electrical outlet. The VOICE MAIL/CHARGE/IN USE
indicator lights, verifying the battery is charging.
Charge the handset battery for 12 continuous hours prior to first use. The initial
battery charge is important for best performance.
Note: The handset can be charged facing up or down.
Base
AC adaptor
A10920
Telephone line
cord
Handset
Belt clip
(CLT-9925/9935 only)
Replacement Battery
Order Form
1
2
3
SOS HELP LINE
At Sanyo, fulfilling the needs of our customers is a priority. That’s why we
created our SOS customer service program that guarantees satisfaction.
NATIONWIDE CUSTOMER SUPPORT
SOS is there to help you. Our friendly and knowledgeable product specialists will
quickly answer your questions about setup and use of Sanyo telephone
products. Simply call toll free from anywhere in Canada to connect to our nocharge, SOS support and service network:
1-800-263-2244
between 8:30 am – 7:00 pm EST
Or visit our website at www.sanyoservice.com, and click the Customer
Relations button to get access to our FAQ’s (Frequently Asked Questions) and
other helpful features.
STAY-AT-HOME CONVENIENCE
It’s a nuisance making another trip to the store when you’re stuck. Now with
SOS, all that’s necessary is a quick call from your home for product assistance.
HASSLE-FREE EXCHANGE
Should your Sanyo telephone require servicing due to a manufacturing defect
during the warranty period, SANYO Canada will ship prepaid a replacement
unit* within two business days after receiving your defective unit. Consumers
are responsible for the shipping costs of the unit back to Sanyo.
• For older, non-current models, replacement units may not be available, in
which case our regular warranty conditions will apply.
GUARANTEED QUALITY
All SOS replacement sets are checked and serviced by factory-authorized technicians before being sent out. SOS means you never have to worry.
C.O.D. and/or Collect shipments will not be accepted.
Unit must be returned to Sanyo in its original box with all accessories, ie:
owner’s manual, battery, adaptor, telephone cord, etc.
SANYO E2002-2
The exclamation point within the triangle is a warning sign alerting
you of important instructions accompanying the product.
CLT-9922NEW 7/2/02 11:09 AM Page 1
Low Battery Warning: When the battery is low you will hear a short beep every
7 seconds.
Important: Do not connect the telephone line to the modular jack until the phone
has been charged for 12 continuous hours.
3. Plug the telephone line cord into the
PHONE LINE jack on the bottom of the
base and into a modular jack.
Caution: Use only Sanyo AC adaptor, A10920, that came with this phone. Using
other adaptors may damage the phone.
Note: The phone automatically defaults to touch tone dialing. To change to pulse
(rotary) dialing, see Tone/Pulse Dialing. If you do not know which type of service you
have, check with your telephone company.
Mounting on a wall
Do not attempt to wall-mount the phone before initial 12-hour charging is
completed.
1. Follow previous steps 1–2 to charge the handset. Wait at least 12 hours.
2. Plug the telephone line cord into the
PHONE LINE jack on the bottom of the
base and the other end into a modular jack.
3. Slip the mounting holes on the bracket over the wall plate posts and firmly slide
the base down into place (wall plate not included).
4. Place the handset in the base.
Note: If desired, gather the extra line cord together, and fasten with a wire tie.
Digital Security System
Your cordless phone uses a digital security system to provide protection against
false ringing, unauthorized access and charges to your phone line.
When you place the handset in the base, the unit verifies its security code. After
a power outage or battery replacement, place the handset in the base for about
20 seconds to reset the code.
INITIAL PROGRAMMING
Before using this telephone the following 3 initial program set-ups must be
completed:
Language setting
1. Make sure the phone is off (not in TALK mode).
2. Press
FLASH/PROG until
11EENNGG 22FFRRAA 33EESSPP
shows on screen. English is factory
set.
3. Use the handset number keys to enter the desired setting. For example, to
choose French, press the number
2 key.
4. Press
FLASH/PROG to store selection. You will hear a confirmation tone.
Tone/pulse setting
1. Make sure the phone is off (not in TALK mode).
2. Press
FLASH/PROG until
11 TTOONNEE 22 PPUULLSSEE
shows on screen. Tone is factory set.
3. Use the number keys to enter the desired setting. For example, to choose Tone
dialing, press the number
1 key.
4. Press
FLASH/PROG to store selection. You will hear a confirmation tone.
Area code setting
This is required to use Caller ID service from your telephone company.
1. Make sure the phone is off (not in TALK mode).
2. Press
FLASH/PROG until
------ SSEETT AARREEAA CCOODDEE
shows on screen.
3. Use the handset key pad to enter your 3-digit area code.
4. Press
FLASH/PROG to store selection. You will hear a confirmation tone.
NAMES AND CONTROLS
1. LCD screen
2. CID/VOL ▼ (volume) key
3. REDIAL key
4. MEM (memory) key
5. TONE/CANCEL key
6. CHAN (channel)/DEL (delete) key
7. Ringer switch: RINGER ON/OFF
8. TALK/CALLBACK key
9. CID/VOL ▲ (volume) key
10. 7-10-11 key
11. PAUSE key
12. FLASH/PROG (program) key
1
2
3
4
BASICS
Receiving a call
1. When the phone rings the screen shows caller information*.
2. Press
TALK.
* If you do not subscribe to a caller ID service, there will be no information on display.
Ringer switch
The RINGER switch must be ON for the handset to ring during incoming calls.
Volume
While talking, press
CID/VOL keys ( ▲ and ▼ ) to control the receiver volume.
There are four volume levels. Press ▲ to increase the volume level, and press
▼ to decrease.
VVOOLL 11
is the lowest level and
VVOOLL 44
is the loudest.
Making a call
Press
TALK/CALL BACK before you dial and press it again to hang up.
Redialing a call
Press TALK/CALL BACK and then REDIAL to redial the last number you dialed
(up to 32 digits). If you get a busy signal, and want to keep dialing the number, just
press REDIAL again (you do not have to turn the phone off and back on).
FLASH key
Use the
FLASH/PROG key to use special calling services such as Call Waiting or
Call Transfer. You must subscribe to these services available through your local
phone company.
Tip : Do not use
TALK/CALL BACK to activate custom calling services or you’ll
hang up the phone.
VOICE MAIL/CHARGE/IN USE indicator
• Flashes when you have a new voice mail.
• Lights when the handset is being charged in the base.
• Lights when the handset is in use.
Voice mail
When you subscribe to a voice mail service offered by
your phone company, the phone alerts you when voice
mail has been received.
MMEESSSSAAGGEE WWAAIITTIINNGG
appears on
screen for 60 seconds when a voice mail is received. The
VOICE MAIL/CHARGE/IN USE indicator on the base
flashes to indicate there is voice mail waiting. After the
voice mail has been reviewed
MMSSGG WWAAIITTIINNGG OOFFFF
appears
on screen and the VOICE MAIL/CHARGE/IN USE
indicator stops flashing.
This indicator does not work with your answering machine.
Note: The phone will only work with an FSK type of VMWI system. It will not work
with the Stutter Dial Tone type of VMWI system.
CHAN (Channel) key
Press and release
CHAN/DEL to advance to the next channel to get rid of static
while talking.
Temporary tone
This feature enables pulse (rotary) service phone users to access touch-tone
services offered by banks, credit card companies, etc.
1. Call the bank’s information line.
2. Press TONE/CANCEL after your call is connected.
3. Follow the voice instructions to complete your transaction.
4. Hang up when finished. The phone returns to pulse (rotary) service.
CANCEL key
Press
TONE/CANCEL to cancel any command you initiated.
Handset locator
This feature helps to locate a misplaced handset. Press
PAGE on the base. The
handset beeps continuously for about two minutes or until you press any key on
the handset. Press PAGE to cancel.
Note: The
RINGER switch does not have to be ON for this feature to work.
CALLER ID FEATURES
This phone receives and displays caller’s information when you subscribe to a
Caller ID service from your telephone company. This information can include the
phone number, date, and time; or the name, phone number, date, and time. The
phone can store up to 40 callers for later review.
PAGE button
VOICE MAIL/IN USE/
CHARGE indicator
Time Date Number of calls
CLT-9922NEW 7/2/02 11:09 AM Page 2
Loading...