DVD Input: Component Video Jack-Y 1 (1.0Vp-p, impedance 75Ω)
Component Video Jack CB/CR 1 (0.7Vp-p, impedance 75Ω)
Audio inputs: Phono jack (L/R) x 2 (500mVrms, more than 47KΩ)
Video monitor outputs: Phono jack x 1 (1Vp - p, 75Ω)
Audio monitor outputs: Phono jack (L/R) x 1 (500mVrms, less than 820Ω)
Headphone jack: Mini stereo jack x 1
Give complete “SERVICE REF. NO.” for
parts order or servicing. It is shown on the
rating plate at the cabinet back of the unit.
This T.V. receiver will not work properly in
foreign countries where the television
transmission system and power source differ from the design specifications. Refer to
the specification table.
1: An isolation transformer should be connected in the
power line between the receiver and the AC line
when a service is performed on the primary of the
converter transformer of the set.
2: Comply with all caution and safety-related notes pro-
vided on the cabinet back, inside the cabinet, on the
chassis or the picture tube.
3: When replacing a chassis in the cabinet, always be
certain that all the protective devices are installed
properly, such as, control knobs, adjustment covers
or shields, barriers, isolation resistor-capacitor networks etc.. Before returning any television to the
customer, the service technician must be sure that
it is completely safe to operate without danger of
electrical shock.
X-RADIATION PRECAUTION
The primary source of X-RADIATION in television receiver is the picture tube. The picture tube is specially constructed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must be
the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X
- RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit. Refer to this
service manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits,
take necessary corrective action. Carefully follow the instructions for + B1 volt power supply adjustment, and high
voltage check to maintain the high voltage within the specified limits.
PRODUCT SAFETY NOTICE
Product safety should be considered when a component replacement is made in any area of a receiver.
Components indicated by mark in the parts list and the schematic diagram designate components in which
safety can be of special significance. It is particularly recommended that only parts designated on the parts list
in this manual be used for component replacement designated by mark . No deviations from resistance
wattage or voltage ratings may be made for replacement items designated by mark .
-2-
Page 3
Chassis Block Diagrams
MAIN SIGNAL PROCESSING CIRCUIT
S-Terminal and S-Woofer speaker are not equipped.
1SIFoutSIF Output (NICAM)
2IFAGC-FIF AGC Filter
3SIF-INSIF Input
4FM-FFilter for the DC loop of FM detector
5FMoutFM detector output
6Aud outAudio output
7SND-APC-FSnd VCO frequency is locked at
500kHz from SIF
8IF-VccDC Supply pin for IF circuit
9VM/Ext-A-INExternal audio signal input
10ABLAuto Beam Limiter function
11RGB VccVcc input pin of RGB output block
function
12R-OutR signal output pin function
13G-OutG signal output pin function
14B-OutB signal output pin function
15NCNot Connected
16VrampTo generate a ramp waveform for the
reference V-out
17V-outOutput pin of vertical synchronization
ramp signal
18IrefProducing reference current function
19H-VccVcc of Horizontal deflection and BUS
interface
20AFC-FAFC Filter pin of horizontal VCO
function
21H-outHorizontal output pin
22VCD-GNDVideo Chroma Deflection GND
23Power Fail INPower Fail Input function
24S-TERM INS-Video input
25STATUS INFactory PC mode status (L=ON)
26Remote INRemote Control signal receiver
27P14/PWM1
28P15/PWM2
29ON-TIMER LED OUT On timer led out function
30MUTE OUTMute out function
31IIC SDA1IIC-Bus Data Line
32IIC SCK1IIC-Bus Clock Line
33X ’ talCrystal Oscillator
34X ’ talCrystal Oscillator
355VSupply (5V)
36Power OutPower On/Off signal output
37Bass Expander Bass Expander On/Off function
ON/OFF OUT
38VIF M OUTVIF M Out/Bilingual Out function
/Bilingual Out
39AD KEY INKey signal input
40RESETRESET pin function
41FILTFILT pin function
Pin No. SymbolFunction
42GNDGround
43CCD-VccVcc (5V) pin for 1H delay-line
44FBP-INFly Back Pulse Input
45YC-CY/C-C Input function
46YC-YY/C-Y Input function
47C-APC2AFC filter pin of chroma VCO.
50X ’ tal4.43MHz Crystal
51CR-INCRInput (for DVD)
52SVO/FSCSelected Video Output or FSC Output
53C-APC-FChroma APC Filter
54Ext-Video-INExt Video Input & Y Input in S-VHS
mode
55VCD-VccVideo Chroma Deflection VCC
56Int-Video-INInt. Video Input & Chroma Signal
Input in S-VHS mode
57Blk-FBlack peak level detection in black
stretch circuit.
58PIF-APC-FAPC filter pin for PLL circuit function.
59AFTAutomatic Fine Tuning Output pin
60Video outVideo Output pin
61RF AGCRF AGC Output pin
62IF-GNDGround of IF circuit
63VIF INPIF input pin
64VIF INPIF input pin
-7-
Page 8
Service Information
Protection Circuit
This TV set has a built-in power supply protection circuit.
It is provided to protect the TV set in case of a power supply circuit malfunctions. When something abnormality
occurs during TV reception, the TV set goes to the stand-by mode.
When an abnormality occurs during TV reception, it causes pin 23 of the CPU to go continually Low for about
one second. The CPU detects that this has occurred and outputs the signal from pin 36 to switch off the power
supply lines.
Releasing the protective circuit and restoring power supply
To release the protective circuit and restore power supply, turn the power to the TV set OFF and then ON again
via either the main power switch or the ON-OFF button on the remote control. This will work only if the power
supply trouble was temporary. If there is permanent trouble such as a damaged circuit, power cannot be
restored and the circuit will have to be repaired.
-8-
Page 9
Service Adjustments with Replacing Memory IC(IC801)
Note: The CPU (IC201) and memory IC (IC801) store the service adjustments data and controls data for each
circuit.When the Memory IC(IC801) is replaced, some of the service adjustments should be readjusted to
obtain the best performance. The necessary service adjustments are carried out by using the RC handset.
Please set up the TV set with following steps [1] to [2].
[1] Initializing Procedure
1. Put a new memory IC.
2. Turn on the TV set.
3. Press and hold the TV/AV Selector on the TV set for more than 2 seconds. The following picture appears on the
screen.
TV/AV
MENU
CLR
4. Press the PROGRAMME UP on the TV set while the above On-Screen Display is still on the screen. The following
picture appears on the screen.
- +
TV/AV Selector
CH
TV/AV
MENU
1
This completes the initialization of memory IC.
Following shows the initialized contents of memory data by this procedure.
157 1LINEMOD 0~10Color Output Data Option at 1 Line Mode
158 OPT VM0~10Select VM Out or Ext Audio In
159 OPT ERGB0~11Select Video In or RGB In
160 AUDGAIN0~71Gain Control LV1116
161 L/RGAIN0~76L/R Output Gain Control LV111
300R000~25582ROM Correction
301R010~255244ROM Correction
302R020~25584ROM Correction
303R030~255249ROM Correction
304R040~255173ROM Correction
305R050~255101ROM Correction
306R060~2550ROM Correction
307R070~2550ROM Correction
308R080~2557ROM Correction
309R090~25519ROM Correction
310R100~2552ROM Correction
311R110~255136ROM Correction
312R120~255224ROM Correction
313R130~2553ROM Correction
314R140~25533ROM Correction
315R150~25582ROM Correction
316R160~255246ROM Correction
317R170~25533ROM Correction
DATA INITIAL
DATA
Notes: The initial value that the CPU writes down the CPU ROM data to the memory when replaced the memory IC.
TV set may not operate correctly with this initial value. It is required to set up the fine adjustment for service
adjustments described in the above.
-11-
Page 12
Service Adjustments with Replacing Memory IC(IC801)
No.ITEMRANGE SETUP DESCRIPTION
318R180~25583ROM Correction
319R190~2551ROM Correction
320R200~2550ROM Correction
321R210~2550ROM Correction
322R220~2550ROM Correction
323R230~2550ROM Correction
324R240~25534ROM Correction
325R250~255153ROM Correction
326R260~255100ROM Correction
327R270~25533ROM Correction
328R280~255173ROM Correction
329R290~25585ROM Correction
330R300~2550ROM Correction
331R310~2550ROM Correction
332R320~2550ROM Correction
333R330~2550ROM Correction
334R340~2550ROM Correction
335R350~2550ROM Correction
336R360~2550ROM Correction
337R370~2550ROM Correction
338R380~2550ROM Correction
339R390~2550ROM Correction
340R400~2550ROM Correction
341R410~255136ROM Correction
342R420~255224ROM Correction
343R430~2554ROM Correction
344R440~255223ROM Correction
345R450~2550ROM Correction
346R460~2551ROM Correction
347R470~2552ROM Correction
348R480~255255ROM Correction
349R490~2550ROM Correction
350R500~25533ROM Correction
351R510~25584ROM Correction
352R520~255251ROM Correction
353R530~2550ROM Correction
354R540~2550ROM Correction
355R550~2550ROM Correction
356R560~2550ROM Correction
357R570~2550ROM Correction
358R580~2550ROM Correction
359R590~2550ROM Correction
360R600~2550ROM Correction
361R610~2550ROM Correction
362R620~2550ROM Correction
DATA INITIAL
DATA
No.ITEMRANGE SETUP DESCRIPTION
363R630~2550ROM Correction
364R640~2550ROM Correction
365R650~2550ROM Correction
366R660~2550ROM Correction
367R670~2550ROM Correction
368R680~2550ROM Correction
369R690~2550ROM Correction
370R700~2550ROM Correction
371R710~2550ROM Correction
372R720~2550ROM Correction
373R730~2551ROM Correction
374R740~255205ROM Correction
375R750~2550ROM Correction
376R760~2550ROM Correction
377R770~255109ROM Correction
DATA INITIAL
DATA
-12-
Page 13
Service Adjustments with Replacing Memory IC(IC801)
MENU
[Entering to Service Mode]
1. Press and hold the MENU button on the Remote Control and press the VOLUME (+) button on the TV set.
Following setting items appears on the screen.
MENU
Display for [RF AGC] RF AGC adjustment
MENU
Read Status
SI. 00100101S2.11111000
- +
CH
ADDRESS
01
RF AGC
DATA
30
Item No.
Item
Data value
2. Select item by pressing the TIMER (Item No. UP) or SOUND MUTE (Item No. DOWN) button on the remote control
handset.
TIMER
x
0102030405......84...
Example
Display for [V-SCO] V-S Correction adjustment
SI. 00100101S2.11111000
ADDRESS
05
V-SCO
07
DATA
9
Read Status
Display for [DRV] White balance adjustment
SI. 11100101S2.11110001
ADDRESS
RD 64GD 8BD 64
37
...8483828180......01
Read Status
DATA
Data value for Blue
Item No.
Item
Data value
3. Adjust data value by pressing the VOLUME + or VOLUME
To return to normal TV mode, press the MENU button on the TV set or the remote control handset.
-13-
Item No.
-
button on the remote control handset.
Item
Data value for Red/Green
Page 14
Service Mode Adjustments
Following adjustments should be carried out when the memory IC is replaced. How to enter the service mode and
adjust values, please refer to “ Entering to Service mode” on page 13.
Item 01 [RF AGC] AGC
NOTE: Do not attempt this adjustment with weak signal.
(1) Tune the receiver to most clearest (or strongest) VHF
station in your area. Set the brightness and contrast
controls to maximum. Set the colour control to
minimum.
(2) Select [RF AGC] in the service mode.
(3) Change value until the snow noise just disappears.
(4) Exit from service mode.
Item 02 [H-PHA] HORIZONTAL CENTRE
(1) Receive a monochrome circular pattern.
(2) Set the brightness and contrast to normal.
(3) Select [H-PHA] in the service mode.
(4) Change value to be optimum horizontal centre position.
(5) Exit from service mode.
Horizontal centre
c
d
e
Upper
Center
Bottom
Item 06 [V-LIN] VERTICAL LINEARITY
(1) Receive a crosshatch pattern.
(2) Select a picture mode of NATURAL by pressing the
PICTURE MODE button.
(3) Select [V-LIN] in the service mode.
(4) Adjust Vertical Linearity so that the difference of “a” and
“b” becomes less than 3mm by pressing VOLUME + or
- button.
(5) Exit from service mode.
Upper
a
Center
b
Item 05 [V-SIZ] VERTICAL SIZE
(1) Receive a monochrome circular pattern.
(2) Set the brightness and contrast to maximum.
(3) Select [V-SIZ] in the service mode.
(4) Change value to be optimum vertical size.
(5) Exit from service mode.
Vertical size
Item 07 [V-SCO] V-S CORRECTION
(1) Receive a crosshatch pattern.
(2) Select a picture mode of NATURAL by pressing the
PICTURE MODE button.
(3) Select [V-SCO] in the service mode.
(4) Adjust Vertical S-letter Correction so that the difference
of “c”, “d” and “e” becomes less than 2 mm by pressing
the VOLUME + or - button.
(5) Confirm Vertical Linearity and adjust Vertical Center
then Vertical Size.
(6) Exit from service mode.
Bottom
Item 18~21 [PCC] PCC Adjustment
(1) Receive a crosshatch pattern.
(2) Select a picture mode of NATURAL by pressing the
PICTURE MODE button.
(3) Select [EWAMP] in the service mode.
(4) Adjust Vertical Lines to be adequately straight.
(5) Select [EWTILT] in the service mode.
(6) Adjust Vertical Lines to be adequately parallel each
other.
(7) Select [EWTOP] in the service mode.
(8) Adjust Left and Right top corner so that vertical lines
more straight.
(9) Select [EWBTM] in the service mode.
(10) Adjust Left and Right bottom corner so that vertical
lines more straight.
-14-
Page 15
Service Mode Adjustments
JP409
R488
T471-H5
1
JP408
C471
R481
T471-H7
T471-H6
T471-H4
T471-H8
T471-H10
R481A
JP407
JP414
J4
Items 30-33, 35-37 GREY SCALE
(1) Receive a monochrome circular pattern.
(2) Set the brightness and colour to normal, contrast to maximum.
(3) Enter to the service mode.
(4) Select No. 30 RBIAS (Red Bias), No, 31 GBIAS (Green Bias), and No. 32 BBIAS (Blue Bias) and set each data to 0
by pressing the VOLUME + or - key.
(5) Select No. 33 RDRIV (Red Drive) and No. 35 BDRIV (Blue Drive) and set each data to 64 by pressing the VOLUME
+ or - key.
(6) Turn Screen Control on the FBT (T471) to minimum (fully counter-clock-wise).
(7) Select No. 36 (1-line appear).
(8) Advance Screen Control clockwise to obtain just visible one colour line. If line does not appear, place this control to
maximum (fully clockwise).
(9) Raise each Bias Level with 1, 2, 5, 6, 9 and 0 keys to obtain just visible white line.
(10) Select No. 37 DRV (Drive Adjustments).
(11) Adjust Red and Blue Drive Levels alternately with 3, 4, -/-- or RECALL key to produce normal black and white
picture in highlight areas.
(12) Check for proper grayscale at all brightness levels. To turn off the TV Service Menu display, press the MENU key.
Note: If the Grayscale adjustment is made after picture tube replacement, check the High Voltage
Blue Drive +
Red Bias -
Red Drive +
Green Bias -
Blue Drive -
Blue Bias +
TV/AV
SWAP
.
A B
BASS
1
4
7
-/--
TIMER
2
56
8
0
CH
MENU
CH
SOUND
S. SYS
JXPSC
x
3
9
CH SCAN
PICTURE
SURROUND
PP
Red Bias +
Red Drive -
Green Bias +
Blue Bias -
Press the MENU button to exit
from service mode.
MAIN BOARD
SCREEN VR
(Under side)
-15-
Page 16
Service Adjustments
34
21
E
7
10
9
E
E
C629
R628
R629
JP412
T471-H1
KDY-6
KDY-3
D466
JP403
R422
R435
R423
JP410
T471-H2
L462
JP435
L441A
L441
KDY
JP436
C450
R450
C437
R482
D489
D464
R487
D465
70
C355
C463
R470
R471
R421
L403
J406
R473
D460
R466
L462A
C465
D461
R462
C467
D441
R442
R441
R445
L461
L461A
J404
L442A
R103
L442-H2
L442-H1
L462-H2
L462-H1
L462-H3
L441-H3
L441-H1
D610
J422
C691
J647
Q462
J407
C434
C432
R525
VR631
R636
R635
D686
JW7
JW8
D353
D421
R355
L441-H2
J405
JP442
J424
J425
J409
C524
C44
C44
T431A
T431-H3
T431-H1
T431-H2
T431-H4
T431
C641-H2
8
9
10
Q461
Q461A
+B ADJST.
D43
D439
JP441
T611-H10
T611-H8
T611-H11
Q432
C425
C424
J423
R427
R405
J411
T611A-H10T611A-H11
T611A-H8
J413
R410
R411
Q405
J414
R408
J415
Q406
J403
J416
J645
611-H7
A-H7
L442
JW10
W12
KDY-5
J609
605
614
R610
D613
D612
IC601-1
J421
J427
D615
616
R103A
JP416
J631
J646
R685
D687
C636
J680
JP442A
JP441A
J417
C437A
JW17
JW18
R
R421
0
R52
Q461
Following adjustments are not required to readjust when replacing the memory IC.
B-VOLTAGE SUPPLY CHECKING
(1) Connect DC meter to TP-B and the ground.
(2) Tune the receiver to an active channel and synchro-
nized picture. Select NATURAL picture mode by pressing the PICTURE MODE button on the remote control.
(3) Adjust B-voltage to be 140 ± 0.5V DC by using VR631.
MAIN BOARD
TP-B
HIGH VOLTAGE CHECK
Note: +B (+140V) Voltage Check and Grayscale Adjustment
must be completed before attempting High Voltage Check.
(1) Connect high voltage voltmeter negative lead to
ground, and connect + lead to anode of picture tube.
(2) Tune receiver to an active channel and confirm TV is
operating properly.
(3) Maximize the beam current by adjusting the contrast
and brightness controls to maximum. Confirm high
voltage is within 28.0 KV and 30.0 KV at maximum
beam current.
(4) Eliminate the beam current by adjusting the contrast
and brightness controls to minimum. Confirm high
voltage does not exceed 31.5 KV at zero beam current.
If reading is not within range, check horizontal circuit.
No high-voltage adjustment is provided on this chassis.
B-Voltage Supply Adjustment
FOCUS ADJUSTMENT
(1) Receive the monochrome circular pattern.
(2) Set the brightness to normal and contrast to maximum.
(3) Adjust the focus control on the F.B.T. for the best focus
on the screen centre.
MAIN BOARD
5
Q405
R422
JP410
J405
E
L442-H1
J414
JP412
R466
J415
JP435
JP411
C465
R477
R435
C524
T471-H2
T471-H1
JP408
T471-H4
T471-H5
T471-H10
T471-H8
T471-H7
T471-H6
R442
R405
3
5
D489
JP442
L442-H2
R408
L461
R473
R470
R471
C470
R474
R482
C437
C482
L442A
L442
L461A
J427
R411
E
C437A
Q406
JP416
J416
R410
R423
J403
R450
C450
J417
R424
C468
TP-B
JP409
R488
JP407
E
Q402
J410
R481
R481A
C471
JP414
Focus VR
(Upper side)
-16-
Page 17
Special Function
TUN ING LO CK
OFF
TUN ING LO CK
ON
VOL UME LO CK
OFF
MENU
MENU
The following special functions can be set up on this TV
set.
(1) Volume Lock setting
With this function, a maximum sound volume limit can be set at
any level.
BASS EXPANDER ON
SOUND
IIIIIIII
(2) Tuning Lock setting
Once TUNING LOCK is switched on, further channel tuning
(Pre-set) is not possible. The Channel Swapping function also
is not possible.
TUNING LOCKED
(3) Music Mode setting
When Music Mode is ON, Programme position from “247” to
“255” and “0” are set Music Mode. Only sound is provided and
any picture is not on the screen under Music Mode.
How to set the special function:
Note: When making the VOLUME LOCK setting, set thedesired maximum sound volume by pressing the VOLUME + or
-
button before entering Special Function setting mode.
To enter into the special function setting mode, press and
1
hold the MENU button of the remote control, then press the
PROGRAMME DOWN button on the TV set.
MENU
VOLUME LOCK
TUNING LOCK
MUSIC MODE
AV START
- +
CH
SELECT ADJUST
Select an item of the special functions by pressing the
2
PROGRAMME UP or DOWN button on the remote control
or the TV set.
VOLUME LOCK
TUNING LOCK
MUSIC MODE
AV START
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
M
EXIT
MUSIC
screen
(4) AV Start setting
Turns black
Set AV-START to ON and every time the TV set is switched on,
AV1 position will be the initial programme position.
AV1
SELECT ADJUST
Set the selected special function “ ON “ by pressing the
3
VOLUME + or -button. To cancel, set to “ OFF”.
VOLUME LOCK
TUNING LOCK
MUSIC MODE
AV START
SELECT ADJUST
OFF
ON
OFF
OFF
Press the MENU button of the remote control to return to
4
the normal TV mode.
MENU
M
EXIT
M
EXIT
-17-
Page 18
Purity and Convergence Adjustment
CAUTION: The Convergence and Purity adjustments have been made at the factory. Readjustment
should be made only after picture tube or deflection yoke replacement, following the steps below:
Signals: Use a pattern generator which can output red,
green, blue and white raster and crosshatch
pattern signals.
Procedure: Carry out purity adjustment first, and then carry
out convergence adjustment.
Preparation: The deflection yoke may have several
correction magnets attached to its outer
edge. If replacing the picture tube, the
positions of the magnets can be changed and
they can be re-used, so remove these
magnets and keep them safely so that they
do not get lost.
PURITY ADJUSTMENTS
1. Place the picture so that its front faces west.
2. Insert the power plug into a wall outlet, and then turn on
the power for the TV and de-magnetize the TV using its
own degaussing circuit.
3. Loosen the screw which is holding the deflection yoke
(with integrated purity magnets), and then move the
deflection yoke forward as far as it will go. Remove the
rubber wedge at this time.
4. Turn off the red and blue raster so that only the green
raster is on.
5. Adjust the angle between the tabs (wings) on purity
magnets to center the vertical green belt in the picture
tube screen. (See Figures 2 and 3.)
NOTE: This adjustment can only be carried out by
changing the angle, not by rotating the tabs up and
down.
6. Gently move the deflection yoke back to the position
where the green band fills the whole of the picture tube
screen, and then tighten the screw to secure the
deflection yoke in place.
7. If there is any color distortion around the edges, correct
it by attaching magnets to the outer edge of the
deflection yoke. The magnets should be attached so
that the line running from the position of the distortion to
the center of the picture tube intersects the deflection
yoke. The colors on the magnets indicate the north and
south poles of the magnets. Attach the magnets in
whichever direction causes the distortion to
disappear.(See Figures 1 and 4. The south and north
pole positions are shown as a guide.)
8. Switch the screen to red and blue rasters and check that
there is no color distortion. If there is any distortion,
adjust the angles of purity magnets tabs or the forwardback position of the deflection yoke, or change the
attachment positions of the
correction magnets.
N
S
Figure 1
Rubber wedge
Correction
magnet
Deflection yoke
mounting scrrew
Move the deflection
yoke back and forth to
adjust the purity
Figure 2
Change the angle to adjust the green band so that it is
centered in the screen.
FOUR-POLE
MAGNET TABS
ANGLE
OF TABS
PURITY
MAGNET
TABS
Figure 3
Figure 4
Color Distortion
Magnet attachment position
Deflection Yoke
outer edge
1
SIX-POLE
MAGNET TABS
3
2
4
GREEN band
-18-
Page 19
Purity and Convergence Adjustment
CONVERGENCE ADJUSTMENT
Preparation: After carrying out purity adjustment and
before proceeding to convergence
adjustment, provisionally insert the rubber
wedge so that there is no vertical or
sideways play in the deflection yoke.
Signals: Display a crosshatch pattern.
1. Red/blue center adjustment
Adjust the angle between the tabs (1) and (2) in Figure
5 and rotate them together until the lines of the red and
blue crosshatch patterns (vertical and horizontal lines)
are superimposed in the center of the screen.
2. Green and red/blue center adjustment
Adjust the angle between the tabs (3) and (4) in Figure
5 and rotate them together until the lines of the green
crosshatch pattern are superimposed with the red/blue
crosshatch pattern (vertical and horizontal lines) which
were superimposed in step 1).
3. Vertical lines at screen center (Red and Blue)
Use the VR2 control (see Figure 8) at the top of the
deflection yoke to correct the vertical line convergence
at the center of the screen.(See Figure 9.)
Figure 5
Figure 6
Figure 7
FOUR-POLE
MAGNET TABS
ANGLE
OF TABS
PURITY
MAGNET
TABS
Red
Blue
Red/Blue
Green
SIX-POLE
MAGNET TABS
3
4
2
1
Adjust the angle rotation of tabs
(1) and (2) to align the vertical
and horizontal lines.
Adjust the angle and rotation of
tabs (3) and (4) to align the vertical
and horizontal lines.
4. Vertical lines at screen top and bottom
Use the VR1 control (see Figure 8) at the top of the
deflection yoke to correct the vertical line convergence
at the top and bottom of the screen. (See Figure 10.)
5. Horizontal lines at screen top and bottom
Rotate the Deflection yoke to the left or right to correct
the horizontal line convergence at the top and bottom of
the screen. (See Figure 11.)
If vertical lines are intersecting at the top and bottom,
use a screwdriver to adjust the Balance coil at the top of
the deflection yoke. (See Figure 12.)
Figure 8
VR1
Balance
coil
VR2
Figure 9
Red
Figure 10
Blue
Red
Figure 11
Figure 12
Blue
Use the VR2 control to correct.
Use the VR1 control to correct.
Red
Blue
Rotate the DY to correct.
-19-
Red
Use the Balance coil to correct
Blue
Page 20
Cabinet Parts List
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
Product safety should be considered when a component replacement is made in any area of a receiver.
Components indicated by a mark in this parts list and the circuit diagram show components whose value have
special significance to product safety. It is particularly recommended that only parts specified on the following parts
list be used for components replacement pointed out by the mark.
Note: Parts order must contain Service Ref. No., Part No., and descriptions. The main PCB unit will be supplied without tuner and
flyback transformer. They should be ordered separately.
Read description in the Capacitor and Resistor as follows:
CAPACITOR
CERAMIC 100P K 50V
Rated Voltage
Tolerance Symbols:
Less than 10pF
A : Not specified B : ±0.1pF C : ±0.25pF
D : ±0.5pF F : ±1PF G : ±2pF
R : ±0.25-0pF S : ±0-0.25pF E : +0-1pF
More than 10pF
A : Not specified B : ±0.1% C : ±0.25%
D : ±0.5% F : ±1% G : ±2%
H : ±3% J : ±5% K : ±10%
L : ±15% M : ±20% N : ±30%
P : +100-0% Q : +30-10% T : +50-10%
U : +75-10% V : +20-10% W : +100-10%
X : +40-20% Y : +150-10% Z : +80-20%
Rated value: P=pico farad, U=micro farad
Material:
CERAMIC........... Ceramic
MT-PAPER......... Metallized Paper
POLYESTER...... Polyester
MT-POLYEST.....Metallized Polyester
POLYPRO.......... Polypropylene
MT-POLYPRO.... Metallized Polypropylene
COMPO FILM..... Composite film
MT-COMPO........ Metallized Composite
STYRENE........... Styrene
TA-SOLID........... Tantalum Solid
AL-SOLID........... Aluminium Solid
ELECT................ Electrolytic
NP-ELECT.......... Non-polarised Electrolytic
OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic
DL-ELECT.......... Double Layered Electrolytic
RESISTOR
CARBON 4.7K J A 1/4W
Rated Wattage
Performance Symbols:
A: General B: Non flammable Z: Low noise
Other: Temperature coefficient
IC001 4096216109 IC TDA8944J/N1
IC201 4106203402 IC LA76938NDE56S0-E
IC202 4092415407 IC BA178M05T
4094636701 IC KIA7805API
4092654806 IC L78M05CV
IC3701 4095922734 IC LV1116NV-TLM-E
IC501 4094535905 IC LA78041
IC601 4105643100 IC STR-W6754(LF2003)
IC651 4092415407 IC BA178M05T
4094636701 IC KIA7805API
4092654806 IC L78M05CV
IC801 4096760701 IC LE24C161-E-C
4104958007 IC AT24C16A-10PU-2.7
4094594506 IC 24LC16B/P
CAPACITOR
C001 4040972303 ELECT 1K U M 25V
4040848400 ELECT 1000U M 25V
4031977340 ELECT 1000U M 25V
C004 4040971900 ELECT 220U M 16V
4040848004 ELECT 220U M 16V
4032006722 ELECT 220U M 16V
C006 4041086306 ELECT 33U M 16V
4040897804 ELECT 33U M 16V
4032006524 ELECT 33U M 16V
C009 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C012 4032989619 CERAMIC 0.1U K 16V
4033670417 CERAMIC 0.1U K 50V
C015 4011506011 MT-GLAZE 0.000 ZA 1/10W
4011057919 MT-GLAZE 0.000 ZA 1/16W
C017 4030708816 CERAMIC 1500P K 50V
4031552111 CERAMIC 1500P K 50V
C018 4030708816 CERAMIC 1500P K 50V
4031552111 CERAMIC 1500P K 50V
C020 4041086306 ELECT 33U M 16V
4040897804 ELECT 33U M 16V
4032006524 ELECT 33U M 16V
C022 4032989619 CERAMIC 0.1U K 16V
4033670417 CERAMIC 0.1U K 50V
C025 4032121613 CERAMIC 0.22U Z 25V
C026 4032121613 CERAMIC 0.22U Z 25V
C1001 4040968405 ELECT 1U M 50V
4040848806 ELECT 1U M 50V
4032001123 ELECT 1U M 50V
C1002 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C1003 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C1004 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C1005 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C1006 4032006722 ELECT 220U M 16V
C1007 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C1008 4040968504 ELECT 10U M 50V
4040848905 ELECT 10U M 50V
4031957748 ELECT 10U M 50V
C1009 4040968405 ELECT 1U M 50V
4040848806 ELECT 1U M 50V
4032001123 ELECT 1U M 50V
C101 4041072002 ELECT 470U M 16V
4040848301 ELECT 470U M 16V
4031768621 ELECT 470U M 16V
C1010 4041087501 ELECT 0.1U M 50V
4040871606 ELECT 0.1U M 50V
4032002219 ELECT 0.1U M 50V
C1011 4033670417 CERAMIC 0.1U K 50V
C1012 4040968405 ELECT 1U M 50V
4040848806 ELECT 1U M 50V
4032001123 ELECT 1U M 50V
C104 4040973508 ELECT 47U M 50V
4040849308 ELECT 47U M 50V
4032001727 ELECT 47U M 50V
C106 4040973102 ELECT 22U M 50V
4040875406 ELECT 22U M 50V
4032001529 ELECT 22U M 50V
C108 4031133815 CERAMIC 1000P K 50V
C111 4032152211 CERAMIC 0.01U K 50V
C112 4032152211 CERAMIC 0.01U K 50V
C114 4032152211 CERAMIC 0.01U K 50V
C120 4030755315 CERAMIC 8200P K 50V
4032152112 CERAMIC 8200P K 50V
C121 4032152211 CERAMIC 0.01U K 50V
C122 4040971702 ELECT 100U M 16V
4040847809 ELECT 100U M 16V
4031957837 ELECT 100U M 16V
C123 4011506011 MT-GLAZE 0.000 ZA 1/10W
4011057919 MT-GLAZE 0.000 ZA 1/16W
C132 4033363517 CERAMIC 0.47U K 16V
C138 4032844314 CERAMIC 0.022U K 50V
C171 4031552111 CERAMIC 1500P K 50V
C172 4032152211 CERAMIC 0.01U K 50V
C174 4031571914 CERAMIC 10P D 50V
C176 4011506011 MT-GLAZE 0.000 ZA 1/10W
4011057919 MT-GLAZE 0.000 ZA 1/16W
C1902 4040973102 ELECT 22U M 50V
4040875406 ELECT 22U M 50V
4032001529 ELECT 22U M 50V
C201 4032152211 CERAMIC 0.01U K 50V
C202 4031793217 POLYESTER 0.015U J 50V
C203 4032152211 CERAMIC 0.01U K 50V
C204 4040968306 ELECT 100U M 25V
4040897200 ELECT 100U M 25V
4031957936 ELECT 100U M 25V
C210 4041088102 ELECT 100U M 50V
4032001826 ELECT 100U M 50V
C212 4031554214 CERAMIC 15P J 50V
C215 4040968405 ELECT 1U M 50V
4040848806 ELECT 1U M 50V
4032001123 ELECT 1U M 50V
C224 4032052818 CERAMIC 0.047U K 25V
C225 4040972709 ELECT 0.47U M 50V
PWB MAIN C7JG (1AA4B10S03000)
ASSY, PWB, MAIN BA4H (1AA0B10S218KA)
SW1906
D606 & D608
C608
L
AV OUT
R
CR
V
CB
AV1-V
AV1-DVD
Y-DVD
VLR
WO-1
HEATER
AUD_R_OUT
200V
MUTE
1/16
GJ470C
R132
1/10
GJ470C
V10B0560N
X801
1K
R818
1/10GJ
2.2KC
R232
25EM100
LBVDJ
C204
25EM100
(LBWAJ:MF)
KK0.01GQ
C227
X
JP206
EM0.47MF
C225
:EM0.47LB
(WAJ:VDJ)
1/16GJ
100C
R894
:1/10GJ
100C
1/16GJ15KC
R837
:1/10GJ15KC
X
JP201
MTZJ5.1A
D352
:RD5.6EB1:
DZXLBZA5.1C
1/16GJ
3KC
R210
:1/10GJ
3KC
X
C818
CD10
CGQ
C174
KK0.01
GQ
C243
25KK
0.047
GQ
C224
1S2076A
D357
1SS133:
ED0434
V10B2930J
X211
:B4V10B0040N
:V10B8020J
1/16
GJ
560C
R140
:1/10
GJ
560C
1K
R817
1/16GJ10KC
R853
:1/10GJ10KC
ON/OFF
X
C353
1/16
GJ
100C
R844
:1/10
GJ
100C
1/16GJ100C
R839
:1/10GJ100C
25KK
0.1GQ
C842
2
EM0.47
MF
C226
:EM0.47
LB(WAJ
:VDJ)
16KK
0.47
GQ
C132
V-OUT
X
R353
1/16GZ0C
JP802
:1/10GZ0C
X
R173
S-SW
1/16GJ
4.7KC
R842
:1/10GJ
4.7KC
R-OUT
RF-AGC
150
R212
J
L201
1K
R830
2
KK
0.022
GQ
C138
SF6376BL
X161
:SF6376Y
12345
KK
0.01
GQ
C172
CJ18
CGQ
C801
REMOTE_IN
CJ18CGQ
C802
1/10GJ
2.2KC
R233
AV1-V/S-Y
EM2.2
LBVDJ
C893
:EM2.2
(LBWAJ
:MF)
25EM10
LBVDJ
C233
:25EM10
LBWAJ
KK0.01GQ
C232
2
VID-OUT
IIC-SDA
CRIN
X
Q173
1
FJ0.015BE
C202
180K
R228
1/16GJ15KC
R838
:1/10GJ15KC
100
R280
Y-DVD
P.F.
X
C133
1/16GJ10KC
R845
:1/10GJ10KC
2SJ470
R243
X
R804
X
R133
100
R211
1/16GJ
47KC
R245
1/10GJ
47KC
X
C213
FM-OUT
1/16GJ
10KC
R814
:1/10GJ
10KC
X
D230
J
JP122
1
2
KK0.01
GQ
C234
1/16GJ
100C
R850
1/10GJ
100C
25KK
0.1GQ
C273
X
C242
KK0.01
GQ
C203
J
L204
1/16GJ27KC
R226
:1/10GJ27KC
X
C125
1/16GJ82KC
R340
:1/10GJ82KC
3.9K
R357
EM1MFL
C215
:EM1LB
(VDJ
:WAJ)
STATUS
EM1MFL
C358
:EM1LB
(VDJ:WAJ)
1/16GJ
4.7KC
R841
:1/10GJ
4.7KC
2SJ5.6
R290
1/16GZ0C
C123
:1/10GZ0C
1
2
1/16GZ0C
JP801
:1/10GZ0C
1/16GJ
10KC
R815
:1/10GJ
10KC
X
C175
2
1/16GJ
10KC
R819
:1/10GJ
10KC
EM100LBVDJ
C210
:EM100MFL
25KK
0.033
GQ
C894
EXT-V
IC201
QXXAVC812N
40
RESET
41
FILT
42
CPU GND
43
CCD
VCC
44
FBP IN
45
YC-C
46
YC-Y
47NC48
DVD-Y
49
CB IN
50
4.43M
CRYSTAL
51
CR IN
52
SVO
1
SIF OUT
53
CHROMA
APC FILT
2
VIF AGC
54
EXT.Y-IN
3
SIF IN
55
V/VERTICAL
VCC
4
FM FILTER
56
INT.VIDEO
5
FM OUT
57
BLACK LVL.
DET.FILT.
6
AUDIO
OUT
58
APC
FILTER
7
SIF APC
FILTER
59
AFT
FILTER
8
IF VCC
9
EXT
AUDIO IN
10
ABL
60
VIDEO OUT
11
RGB VCC
61
RF-AGC
OUT
12
R OUT
62
IF GND
13
G OUT
63
PIF IN2
14
B OUT
64
PIF IN1
15
E/W_OUT
16
V-RAMP
17
V-OUT
18
VCO-IREF
19
H-VCC
20
H-AFCFILTER
21
H-OUT
22
V-VERTICAL
GND
23
P.F.
24
S-VIDEO
25
STATUS
26
REMOTE-IN
27
SDA
28
SCL
29
ONTIMER
30
MUTE
31
IIC-SDA
32
IIC-SCL
33
XT134XT235VDD
36
PWR
ON/OFF
37
BASS/
WOOFER
38
VIF-M/
BILINGUAL
39
KEY_IN
EM1LBVDJ
C863
EM1LBWAJ:
EM1MFL
1/16GZ0C
JP804
:1/10GZ0C
CE1E470
MMFANN
C244
:25EM47
LB(WAJ
:VDJ)
BASS/WOOFER
1/16
GZ0C
R358
1/10
GZ0C
X
C856
2
1/16GJ
33KC
R227
:1/10
GJ
33KC
1
1/16GJ6.8KC
R121
:1/10GJ6.8KC
IIC-SCL
AH
Q122
1
2
3
1/16GF
4.7KC
R286
:1/10
GF
4.7KC
KEY_IN
1/16GJ1MC
R893
:1/10GJ1MC
20K
R351
1/16
GZ0C
C176
:1/10
GZ0C
FBP-IN
1/16GJ2.2KC
R122
:1/10GJ2.2KC
2
1/16GJ
12KC
R225
:1/10GJ
12KC
YC-C
1/16GJ10KC
R834
:1/10GJ10KC
BA178M05T
IC202
L78M05CV:
KIA7805API
123
X
R131
1/16GJ
120C
R235
1/10GJ
120C
H-OUT
47
R230
EM2.2
LBVDJ
C247
EM2.2
(MF:LBWAJ)
CBIN
MTZJ9.1B
D249
:RD9.1EB2
16EM100MF
C805
16EM100LBVDJ:
16EM100LBWAJ
X
R224
16EM47LBVDJ
C291
:16EM47LBWAJ
:16EM47MF
1/16
GJ
10KC
R176
:1/10
GJ
10KC
1/16GJ470C
R840
:1/10GJ470C
X
JP803
1/10GJ
2.2KC
R231
16EM100LBVDJ
C122
16EM100
(LBWAJ:MF)
1/16
GJ
47KC
R244
:1/10
GJ47KC
X
C124
X
R291
X
C816
1/16
GZ0C
R215
:1/10
GZ0C
X
R803
DJ10K
R352
KK1500GQ
C171
1/16GJ
680KC
R229
:1/10GJ
680KC
KK0.01GQ
C803
HJ0.47G
C231
ONTIMER
IF
KK0.01
GQ
C121
1
KK
8200GQ
C120
:KK8200
BA
1
X
C229
X
X161A
12345
1/16GJ270KC
R801
:1/10GJ270KC
X
C228
1/16GJ47KC
R863
:1/10GJ47KC
IC801
1
1
A0
234
5
6
7
8
X
X171
1/16GJ560C
R141
:1/10GJ560C
1/16
GZ0C
R130
1/10
GZ0C
1SS356
D122
1/16GJ10KC
R124
:1/10GJ10KC
1/16GJ
120C
R236
1/10GJ
120C
1/16GJ10KC
R852
:1/10GJ10KC
1/16GZ0C
JP202
:1/10GZ0C
2
G-OUT
25KK
0.1GQ
C843
1/16GJ
120C
R234
1/10GJ
120C
1/16GJ27KC
R125
:1/10GJ27KC
1
2
CJ15C
GQ
C212
ABL
X
R802
1/16GJ10KC
R813
:1/10GJ10KC
B-OUT
5V-1
9V
5V-1
5V-1
5V-2
9V
9V
24V
5VRC
5V-2
5V-2
9V-2
ON/OFF
S10B2790J
SW1901
S10B0450J
12
220
R1913
560
R888
1/16GJ12KC
R1902
:1/10GJ12KC
S10B2790J
SW1905
S10B0450J
12
AH
Q886
220
R1912
S10B2790J
SW1904
S10B0450J
12
2SA933SR
Q1902
KTA1266-TC
REMOTE_IN
1/16GJ5.6KC
R1903
:1/10GJ5.6KC
100
R1907
1/16GJ1.8KC
R1906
:1/10GJ1.8KC
ONTIMER
AA
D1901
KEY_IN
R1901
X
1
1/16GJ22KC
R886
:1/10GJ22KC
220
R1911
U20B32400
A1901
:U20B35900
:U20B63800
1
2
3
S10B2790J
SW1902
S10B0450J
12
1/16GJ3.9KC
R1904
:1/10GJ3.9KC
1/16GJ2.2KC
R1905
:1/10GJ2.2KC
1/16GJ22KC
R887
:1/10GJ22KC
EM22MF
C1902
:EM22LB(WAJ:VDJ)
STB
S10B2790J
SW1903
S10B0450J
12
S10B2790J
SW1906
:S10B0450J
12
EM10LBVDJ
C1007
:EM10LBWAJ
:EM10MFL
1/16GJ1KC
R1014
:1/10GJ1KC
RD11EB3
D1012
:MTZJ11C
X
K1004
1
2
3
4
5
6
78
9
X
JP1029
X
R1023
EM10LBVDJ
C1005
:EM10LBWAJ
:EM10MFL
EM10LBVDJ
C1004
:EM10LBWAJ
:EM10MFL
1/16GJ1KC
R1026
:1/10GJ1KC
RD11EB3
D1004
:MTZJ11C
1/16GJ2.2KC
R1006
:1/10GJ2.2KC
1/16GJ75C
R1021
:1/10GJ75C
1/16GJ1KC
R1031
:1/10GJ1KC
EM1LBVDJ
C1009
:EM1LBWAJ
:EM1MFL
X
JP1004
1/16GJ100KC
R1007
:1/10GJ100KC
AUD_L_OUT
X
D1015
X
IC1001
1
2
3456
7
8
X
JP1002
YC-C
RD11EB3
D1011
:MTZJ11C
CRIN
X
C1013
Y-DVD
X
JP1028
S-SW
1/16GJ75C
R1010
:1/10GJ75C
1/16GJ75C
R1018
:1/10GJ75C
KK0.1GQ
C1011
1/16GZ0C
JP1001
:1/10GZ0C
RD11EB3
D1010
:MTZJ11C
X
C1014
1/16GJ100KC
R1011
:1/10GJ100KC
X
C1015
EM1LBVDJ
C1012
:EM1LBWAJ
:EM1MFL
1/16GZ0C
R1017
:1/10GZ0C
X
JP1003
X
D1014
1/16GJ1KC
R1012
:1/10GJ1KC
RD11EB3
D1006
:MTZJ11C
1/16GJ2.2KC
R1008
:1/10GJ2.2KC
AUD_R_OUT
AJ
Q1002
E
X
D1013
EM10LBVDJ
C1008
:EM10LBWAJ
:EM10MFL
1/16GJ18KC
R1015
:1/10GJ18KC
AJ
Q1003
CE1HR10MMFANN
C1010
:EM0.1LB(WAJ:VDJ)
X
R1022
RD11EB3
D1009
:MTZJ11C
AV1-V/S-Y
1/16GJ18KC
R1013
:1/10GJ18KC
AV1-R
1/16GJ75C
R1016
:1/10GJ75C
1/16GJ1KC
R1029
:1/10GJ1KC
1/16GJ75C
R1020
:1/10GJ75C
AV1-L
RD11EB3
D1007
:MTZJ11C
RD11EB3
D1008
:MTZJ11C
VID-OUT
1/16GJ1KC
R1028
:1/10GJ1KC
CBIN
C1006
16EM220MFL
1K
R1027
AJ
Q1001
1/16GJ100KC
R1009
:1/10GJ100KC
1
X
C1016
1/16GJ560C
R1030
:1/10GJ560C
1/16GZ0C
R1019
:1/10GZ0C
RD11EB3
D1005
:MTZJ11C
X
JP1031
X
R1024
X
R1025
9V
IF
J
R102
KK0.01GQ
C114
KK0.01GQ
C112
1/16GJ
330C
R114
1/10GJ
330C
X
C109
1/16GJ1KC
R111
:1/10GJ1KC
1/16GZ0C
R101
:1/10GZ0C
56
R115
1/16GJ
100C
R107
:1/10GJ
100C
KK0.01GQ
C111
J30B0250N
TP-A
J30B1380N:
B4J30B0040N
1/16GJ18KC
R108
:1/10GJ18KC
MTZJ36A
D103
:RD36EB1
:DZXLBZA36A
X
C105
1SJ39KCE
R103
1
2
1/16GJ
5.6KC
R112
:1/10GJ
5.6KC
EM47LBVDJ
C104
:EM47LBWAJ
:EM47MFL
J
R105
X
TP-E
MTZJ6.8A
D102
:RD6.8EB1
:DZXLBZA6.8A
F1BEB0360
A101
1
AGC
3
ADDRESS
4
CLOCK
5
DATA
6MB7
(MB)
8
N.C
9BT11
IF1
12
GND
13
GND
14
GND
15
GND
16EM
470LBVDJ
C101
:16EM
470LBWAJ
:16EM
470MFL
RF-AGC
KK1000GQ
C108
2SC2814
F4P
Q111
1
X
JP111
X
L111
IIC-SCL
1/16GJ
100C
R106
:1/10GJ
100C
X
TP-M
X
C113
EM22MF
C106
:EM22LB(WAJ:VDJ)
1/16GJ68KC
R109
:1/10GJ68KC
1/16GJ56C
R116
:1/10GJ56C
IIC-SDA
9V-2
9V
140V-1
5V-1
1/16GJ1KC
R1002
:1/10GJ1KC
AV2-L
X
R1032
1/16GJ18KC
R1003
:1/10GJ18KC
EM1LBVDJ
C1001
:EM1LBWAJ
:EM1MFL
AV2-R
1/16GJ1KC
R1004
:1/10GJ1KC
1/16GJ
75C
R1001
:1/10GJ
75C
1
2
MTZJ9.1A
D1002
DZXLBZA9.1(B:C
MTZJ9.1A
D1001
DZXLBZA9.1(B:C)
EM10LBVDJ
C1003
:EM10LBWAJ
:EM10MFL
MTZJ9.1A
D1003
DZXLBZA9.1(B:C
EM10LBVDJ
C1002
:EM10LBWAJ
:EM10MFL
1/16GJ18KC
R1005
:1/10GJ18KC
B4J12B08600
K1003
7
1
2
3
4
5
6
8
9
EXT-V
X
R1001A
1
2
10K
R511
1
2
2400010
KDY-1
1
X
JP502
X
R525
V-OUT
10K
R514
2SJ1KC
R501A
1
2
KK3300CBJ
C518
220
R522
25EM2200LBWAJ
C515
25EM2200LBVDJ:
25EM2200MFC
24V
J
JP501
AH
Q511
P.F.
5.6K
R502
LA78041
IC501
7
123
4
5
6
2400010
KDY-6
1
EM3.3MF
C514
:EM3.3LBWAJ
:EM3.3LBVDJ
100
R519
X
D441
ERA15-02
D512
:DDXLBB012
X
D507
39K
R515
100FK0.1BE
C524
:100FK0.1D
5V-2
C520
100FK0.1BE
:100FK0.1D
1SJ1.2
R518
X
R512
2400010
KDY-3
1
X
KDY-5
1
10K
R510
1
2
X
R501
EM10LBVDJ
C511
EM10LBWAJ:
EM10MFL
15K
R516
35EM220LBVDJ
C517
35EM220LBWAJ:
35EM220MFL
35EM
1000
MFC
C521
:35EM
1000
LB(VD
:WAJ)
2
X
D448
X
JP412
35EM470LBVDJ
C434
35EM470
(LBWAJ:MF)
L441-H2
L71B
0650N
L441
J10EA033N
KQ
1
3
1/2DJ1K
R474
400MJ
0.18CQ
C442
140V
1K
R437
2400030
L441-H3
400MJ
0.15CQ
C441
1/16GJ2.2MC
R483
:1/10GJ2.2MC
J
R466
2SJ4.7D
R481
X
C450
DZXLBZA
7.5A
D489
MTZJ7.5A
J
JP407
ERD07-15L
D438
B4Z21B0160N
L432
Z21B0330N
MTZJ16A
D421
:MTZJ16A
:RD16(EB1:EB3)
AH
Q439
2400010
L442-H2
MTZJ5.1B
D353
X
C423A
ERB44-04
D439
1/16GJ12KC
R491
:1/10GJ12KC
NF68K
R470
1/6NF4.7K
R421
1/2DJ
180K
R482
X
C431
1SS133
D465
1S2076A:
ED0434
160EM0.47
LBVDJ
C482
1/2DJ1K
R433
500KK3900CBJ
C433
L2PC1R0KN
L431
L26B0170N
L461
:LM0045(:D)
:B4L26B0030N
:L26B0260N
KK100CBJ
C355
1K
R424
100GK2.2
C465
100GK2.2P
AJ
Q491
FJ4700D
C463
:FJ4700BE
X
C437A
X
R445
7SJ6.8VC
R435
X
D486
AE
Q462
12K
R492
X
R486
X
C449
100PM2.2X
C471
:100PM2.2
LBZA
CMXAV3Y
702AKN
C423
:1500MH
7000
(XK:AN)
CMXAV3Y722BAS
C420
:1500MH7200
(XK:AN)
680
R473
X
L403
L26A00200
L462
:L26B4630N
HJ0.01G
C470
1/16GJ10KC
R426
:1/10GJ10KC
2SJ
1.8K
R442
140V
400NJ
0.018
EAQ
C425
:400NJ
0.018
LBZA
EM10LBVDJ
C469
EM10LBWAJ:
EM10MFL
500KK680CBJ
C491
X
Q449
J
JP436
5V-2
X
JP442A
2SJ
1K
R441
EU1
D469
:DDXLBB017
MTZJ20A
D466
MTZJ11C
D476
:RD11EB3
500KK1000CBJ
C432
J
JP403
EU1
D485
:DDXLBB017
X
JP411
X
JP441
400NJ
0.02EAQ
C424
1S2076A
D467
ED0434
X
R484
250EM33LBUC
C486
J
JP410
DJ27K
R423
:RDB2702
JPAANN
X
JP409
1/2DJ330
R475
1K
R431
DJ56K
R422
:RDB5602
JPAANN
X
R489
2400030
L441-H1
1/16GJ470C
R493
:1/10GJ470C
1S2076A
D461
1SS133:ED0434
1/16GJ470C
R494
:1/10GJ470C
1.5K
R471
X
R485
EM22MF
C468
:EM22LB
(WAJ:VDJ)
1/16GJ470C
R432
1/10GJ470C
DJ330
R438
1SJ220CE
R434
J
JP408
2.2K
R479
1/2FJ1
R488
X
R449
X
R450
X
JP435
J
JP414
X
D460
DJ10K
R355
X
R490
X
R487
1S2076A
D468
1SS133:
ED0434
HJ1G
C467
2400010
L442-H1
X
D464
16KK
0.47
BA
C439
27K
R462
J
R477
X
R427
X
L442A
X
Q406
X
Q405
X
Q404
X
R408
X
R411
X
R410
X
R409
X
R407
140V-1
X
Q401
X
R401
X
R402
X
Q402
X
Q403
X
R403
X
R404
X
C401
X
R406
STB
5VRC
24V
24V
EU2
D633
:DDXLBB019
X
C653
2400030
T611-H7
1
160EM220XJ
C641
:200EM220XD
:160EM220LBUA
FJ470BE
C610
2400030
PS601-H2
1
275GM0.068XB
C602
250GM0.068XBJ
1
2
630NJ
0.022EAQ
R606
X
R674
2000KK1000DBH
C631
:2000KZ1000CBMC
:CK3A102KCRDJN
:CK3A102KDBHJN
275GK0.22VBB
C601
:250GM0.22XBJ
:275GM0.22(XB:VB)
1.5K
R611
16EM220LBVDJ
C662
16EM220LBWAJ:
16EM220MFL
DHXAAEV0070
PS601
1
23
1SJ220CE
R661
ERC91-02L
D632
35EM470LBVDJ
C643
:35EM470(LBWAJ
:MF)
1/2CK5.6MXG
R628
:1/2DK5.6MLBWAB
J30B0250N
KG-2
J30B1380N:
B4J30B0040N
AH
Q631
1
STB
P.F.
250KK1000XH
C629
:250KM1000XN
:400KK1000(X:VDC)
:CKXLB2G102ZJN
AH
Q641
250KK470XH
:400KK470(X:VDC)
:CKXLB2G471ZHN
C627
ERZV14D471
VA601
:SVC471D07A
1
1
2
2
100
R609
25EM2200LBVDJ
C645
25EM2200LBWAJ:
25EM2200MFC
X
C609-H1
1
DJ3.9K
R687
DJ15KA
R645
1
2
2400010
SW601-H2
1
20V
DJ
150K
R685
1/2CK5.6MXG
R629
:1/2DK5.6MLBWAB
J
R605
1/16GJ10KC
R640
:1/10GJ10KC
EU1
D612
:DDXLBB017
J
R667
1/16GJ6.8KC
R641
:1/10GJ6.8KC
RD6.2EB3
D686
:MTZJ6.2C
2400030
T611-H15
1
EM10LBVDJ
C661
:EM10(LBWAJ
:MFL)
CK3A471KANHNN
C632
:CK3A471KDBHJN
:CK3A471KDBHLC
1
2
CK3A471KANHNN
C634
:CK3A471KDBHJN
:CK3A471KDBHL
RU3M
D634
:DDXLBB021
QXXAVC570
IC601
7
123
4
5
6
J30B0250N
KE-2
J30B1380N:
B4J30B0040N
X
D682
2400030
T611-H2
1
X
R675
J
JP601
10WK1.8LBZCL
R602
1
2
2SA1707S
Q683
:2SA1707T
:2SB985(S:T)
10EM470LBVDJ
C651
10EM470LBWAJ:
10EM470MF
S10B6230N
SW601
2
1
35EM22LBVDJ
C615
:35EM22LBWAJ
5VRC
EM1
LBVDJ
C611
:EM1
(LBWAJ
:MFL)
X
JP602
2400030
L601A-H4
1
1SJ100KCE
R608
EG01C
D611
:DDXLBB011
D609
ED0434
X
C609-H2
1
X
C609
2400030
L601A-H2
1
FJ2200BE
C613
J
JP644
2SJ1
R603
MTZJ6.2B
D614
1
RD10
EB2
D661
2400030
L601-H3
1
AE
Q681
1
1/2DJ
120K
R635
EM22LBVDJ
C649
EM22LBWAJ:
EM22MFL
EM4.7LBVDJ
C650
:EM4.7(LBWAJ
:MF)
1S2076A
D681
:1SS133
:ED0434
560K
R689
1K
R610
J30B0250N
KG-1
J30B1380N:
B4J30B0040N
5.6K
R636
J20B0171J
F601A
12
2400030
L601-H4
1
EM1LBVDJ
C691
EM1LBWAJ:
EM1MFL
DDXLBB044
D631
RU3AM
R3D6222NJ
VR631
:R3D7222NJ
1
3
AE
Q684
2400030
PS601-H1
1
2400030
T611-H13
1
1.5K
R690
140V
2400030
L601A-H1
1
:250KM1000XN
:400KK1000(X:VDC)
:CKXLB2G102ZJN
C628
250KK1000XH
BA178M05T
IC651
L78M05CV:
KIA7805API
123
2SJ
0.47
R604
2400030
L601A-H3
1
2400030
L601-H2
1
J
L632
1
2
100K
R642
CK3A471KANHNN
C633
:CK3A471KDBHJN
:CK3A471KDBHL
FJ0.033
BE
C612
1/16GJ1KC
R681
:1/10GJ1KC
J30B0250N
KE-1
J30B1380N:
B4J30B0040N
25EM1000LBVDJ
C644
25EM1000LBWAJ:
25EM1000MF
1
DJ10K
R686
PC123Y52
:TLP421F-BL
:PC123X5YFZ
D610
1
23
4
2400030
PS601-H3
1
H-DRV
1SJ68K
C614
9V
2HEA0234K
IC601-1
1
2
X
TP-EE
2400030
L601-H1
1
B4F35B0040N
L601
F35B0570N
1
2
3
4
10
R607
X
R644
ON/OFF
2SJ3.9
R668
J30B0250N
KG-3
J30B1380N:
B4J30B0040N
22K
R688
H-DRV
EU1
D613
:DDXLBB017
J
L602
J
L603
X
R601
J
JP604
X
JP603
1000KK
1000CBB
C607
1000KK
1000(HB:LBZB)
1000KK1000CBB
C608
:1000KK1000(HB:LBZB)
X
C606
X
C605
ERC05-10B
D605
:RM11C
:DDXLBB016
2
ERC05-10B
D606
:RM11C
:DDXLBB016
ERC05-10B
D607
:RM11C
:DDXLBB016
ERC05-10B
D608
:RM11C
:DDXLBB016
400EM270XM
C609A
25EM1000LBVDJ
C001
:25EM1000LBWAJ
:25EM1000MF
X
R027
X
JP001
1/16GJ33KC
R011
:1/10GJ33KC
16EM220LBVDJ
C004
:16EM220LBWAJ
:16EM220MFL
X
C002
X
C013
X
JP014
X
C003
1/16GJ33KC
R021
1/10GJ33KC
TDA8944J
IC001
1
LOUT+
2
GND
33
Vcc1
44
ROUT-
55
WFMUTE
66
RIN+
77
SGND
88
LIN+
99
WFIN+
1010
Standby
1111
SVR
1212
WFIN+
1313
n.c.
1414
WFOUT-
1515
GND
1616
Vcc2
1717
WFOUT+
16KK0.1GQ
C022
:KK0.1GQ
X
C014
X
C024
X
R028
X
R030
X
Q002
1/16GZ0C
C015
:1/10GZ0C
X
JP002
X
C023
X
R029
1/16GJ18KC
R022
:1/10GJ18KC
J
C021
1/16GJ18KC
R012
:1/10GJ18KC
20V
16KK0.1GQ
C012
:KK0.1GQ
220
R3704
EM4.7LBWAJ
C3713
EM4.7LBVDJ:
EM4.7MF
IN-R
IN-L
EM4.7MF
C3716
:EM4.7
LB(WAJ
:VDJ)
EM4.7
LBWAJ
C3702
EM4.7
LBVDJ:
EM4.7MF
LV1116NV-EP
IC3701
30
ST-231L-DC
32
LLINEOUT
33
LCH-C34LCH-B35LCH-A
10
R-BC1
36
RGND
11
R-BC212R-OUT
13
R-IN
14
R-VROUT
15
L+R
16
VREF
17
VCC18VDD
19
SDA
1
GND
2
RCH-A3RCH-B
20
SCL21VSS
4
RCH-C
22
L+R LPF
5
RLINEOUT
23
L-VROUT
6
R-DC
24
l-IN
7
ST-1
25
L-OUT
8
LPFC
26
L-BC2
9
R-TC1
27
L-BC128L-TC1
29
HPFC
1/16GJ3.9KC
R3702
:1/10GJ3.9KC
16KK
0.068GQ
C3721
:KK0.068
GQ
X
R3711
AUD_L_OUT
IIC-SCL
25KK
0.1GQ
C3718
16EM1000
MF
C3712
:16EM
1000LB
(VDJ:WAJ)
EM4.7MF
C3715
:EM4.7
LB(WAJ
:VDJ)
KK6800
GQ
C3717
1/16GJ
3.9KC
R3701
:1/10GJ
3.9KC
X
R3703
ERA15-02
D3701
:DDXLBB012
EM4.7MF
C3711
:EM4.7
LB(WAJ
:VDJ)
KK5600
GQ
C3703
EM1MFL
C3722
:EM1LB
(WAJ:VDJ)
16KK
0.068GQ
C3706
:KK0.068
GQ
AUD_R_OUT
EM1MFL
C3710
:EM1LB
(VDJ:WAJ)
16KK
0.068GQ
C3720
:KK0.068
GQ
X
C3723
EM1LBVDJ
C3701
EM1LBWAJ:
EM1MFL
CE1H1R0MMFANC
C3708
:EM1LB(WAJ:VDJ)
AV2-R
FM-OUT
EM1
LBVDJ
C3714
EM1
(MFL:
LBWAJ)
KK2700
GQ
C3719
IIC-SDA
X
C3725
KK0.01
GQ
C3704
AV1-L
16KK
0.068GQ
C3707
:KK
0.068GQ
AV1-R
EM1LBVDJ
C3724
EM1LBWAJ:
EM1MFL
AV2-L
KK2700
GQ
C3705
220
R3705
CK1E224
ZGAFNG
C026
KK1500GQ
C017
:KK1500BA
1/16
GZ0C
JP004
:1/10
GZ0C
CK1E224
ZGAFNG
C025
J10EA043N
K001
:B4J10XC040N
J
JP006
J
JP008
X
JP009
X
JP007
L-/RO+
R-/WO-
J12B06000
K1001
B4J12B02600
1
2
3
4
5
6
7
8
9
X
JP011
1/2DJ390
R1106
1/2DJ390
R1107
L+/LO+
R+/WO+
X
K002
KX
B4J10XC050N
:J10EA053N
1
2
3
4
5
STATUS
IIC-SCL
IIC-SDA
J10EA050N
KP
B4J10XC050N:
J10EA053N
1
2
3
4
5
R-OUT
G-OUT
B-OUT
9V
P.F.
H-OUT
FBP-IN
ABL
EW
MUTE
IN-R
IN-L
L+/LO+
L-/RO+
BASS/WOOFER
R-/WO-
R+/WO+
X
JP1005
WO+1
1/16GZ0C
JP203
:1/10GZ0C
X
JP205
2
KK
0.01
GQ
C201
EW
X
C1017
EM22MF
C510
:EM22LBWAJ
:EM22LBVDJ
EM10LBVDJ
C850
EM10LBWAJ:
EM10MFL
X
D1909
X
D850
X
D1903
X
D1907
X
D1908
X
JP1900
J
JP1901
J
L1901
5VRC
5VRC
X
R405
X
C603
X
R481A
J
JP015
J
JP013
EM1MFL
C245
:EM1LB
(WAJ:VDJ)
X
D1902
X
C107
KDY
J10B0730N
X
Q432A
1
2
X
L462A
1
2
X
L462-H2
1
2400010
L462-H1
1
2400030
L462-H3
1
2400030
T471-H1
1
2400030
T471-H2
1
2400010
T471-H4
1
2400010
T471-H5
1
2400010
T471-H6
1
2400010
T471-H7
1
2400010
T471-H8
1
2400010
T471-H10
1
X
L461A
X
T431A
1
3
4
5
6
B4L18B
0020N
T431
L18B0540N
1
23
4
5
2400030
T431-H1
1
2400030
T431-H3
1
2400030
T431-H4
1
2400030
T431-H2
1
X
L441A
250GK
2.2P
C437
X
L603A
1
2
X
L603B
X
L602A
1
2
X
L602B
X
KE
X
PS601A
1
23
J
L635
X
L601A
1
2
3
4
X
D632A
3
1
2
X
D632B
3
1
2
25EM1000LBVDJ
C663
25EM1000LBWAJ:
25EM1000MF
2400010
C641-H1
1
2400010
C641-H2
1
X
R602A
1
2
X
R602B
1
2
X
R602-H1
1
2400010
R602-H3
1
X
R602-H5
1
X
R602-H2
1
2400010
R602-H4
1
X
R602-H6
1
2400010
C609A-H1
1
2400010
C609A-H2
1
J
C1105
J
C1104
J
JP010
X
C230
X
D1906
X
D1905
X
T611A
1
2
3
4
5
6
7
89
10
11
12
13
14
15
16
17
TXXGA0181753M
Q432
2
3
X
Q432-H1
1
2400030
Q432-H2
1
2SB1274QRA
Q461
:2SB1274RRA
1
2
3
X
Q461A
1
2
3
L51B6950N
T611
1
2
3
4
5
6
7
89
10
11
12
13
14
15
16
17
2400030
T611-H5
1
2400030
T611-H8
1
2400030
T611-H10
1
2400030
T611-H11
1
2400030
T611-H17
1
X
JW1
1
X
JW2
1
X
JW3
1
X
JW4
1
X
JW5
1
X
JW6
1
X
JW7
1
X
JW8
1
X
JW9
1
X
JW10
1
X
JW11
1
X
JW12
1
X
JW13
1
2400030
T611A-H5
1
2400030
T611A-H7
1
KK1500GQ
C018
:KK1500BA
X
JP103
1/16GZ0C
JP105
:1/10GZ0C
1/16GZ0C
JP106
:1/10GZ0C
X
C1107
X
C1107A
2400030
T611A-H13
1
5VRC-1
X
C635
2400030
T611A-H17
1
2400030
T611A-H11
1
2400030
T611A-H10
1
2400030
T611A-H8
1
2400030
T611A-H2
1
2400030
T611A-H15
1
X
D1904
J20B0171J
F601B
12
WO-1
DLXLBB001
D1901
X
D632-H1
1
X
R612
X
D615
X
D616
2400010
SW601-H1
1
1/16GZ0C
JP012
:1/10GZ0C
AH
Q632
1
2
DZXLBZA5.6C
D687
:MTZJ5.6C
EM10LBVDJ
C636
EM10(LBWAJ:MFL)
1/16GJ4.7KC
R638
:1/10GJ4.7KC
1/16GJ
10KC
R637
:1/10GJ
10KC
1SS133
D688
1S2076A:
ED0434
WO
X
R3709
X
R3707
X
R3708
X
R3710
X
R3706
X
C3726
X
Q3701
9V
X
C3729
X
D3702
X
D3703
X
R3712
WO
X
D231
X
C3709
X
C3727
X
R3713
X
JP161
1
2
2000KK
220NH
C617
1
2
X
C604
250KK470XH
:400KK470(X:VDC)
:CKXLB2G471ZHN
C626
X
JP1101
X
JP1102
X
JP1103
X
JP1104
J
JP415
J
JP416
2SJ120
R517
2SC3332S
Q431
:2SC3332R
WO
X
R103A
1
2
X
JP204
B4J30B0040N
TP-B
:J30B0250N
:J30B1380N
9V
1/16GJ
1KC
R639
:1/10GJ
1KC
KK0.1
GQ
C637
X
JP442
X
JP441A
X
C614A
2SD1913SRA
Q661
:2SD1913RRA
:KTC2026
1
X
R016
X
Q009
1/16GZ0C
JP016
:1/10GZ0C
X
R015
X
JP017
1/16GJ
100KC
R008
:1/10GJ
100KC
1/16GJ47KC
R006
:1/10GJ47KC
AH
Q004
AH
Q008
1/16GJ47KC
R031
:1/10GJ47KC
AH
Q003
1/16GJ470KC
R010
:1/10GJ470KC
68K
R009
X
R002
X
Q001
X
R003
X
Q005
X
R007
X
R018
1/16GJ2.2KC
R017
:1/10GJ2.2KC
AJ
Q010
1/16GJ
2.2KC
R037
:1/10GJ
2.2KC
1/16GJ1KC
R038
:1/10GJ1KC
1SS355
D004
:KDS160G
1
1/16GZ0C
JP019
:1/10GZ0C
X
JP020
9V
20V
ON/OFF
X
R023
5VRC-1
X
R014
X
R013
16EM33LBVDJ
C020
:16EM33LBWAJ
:16EM33MF
X
C005
20V
X
C007
X
JW14
1
X
JW15
1
X
JW16
1
X
JW17
1
X
JW18
1
X
Q432B-1
L26B
4560N
L442
123
B4J12B09300
K1101
1515
22
55
11
66
33
2323
2020
2424
2121
1717
1414
1818
88
99
2626
2727
1111
1010
1212
X
JP018
WO+1
WO-1
X
JW19
1
X
JW20
1
X
JW21
1
X
JW22
1
X
JW23
1
X
JW24
1
EM10LBVDJ
C009
:EM10LBWAJ
:EM10MFL
16EM33LBVDJ
C006
:16EM33LBWAJ
:16EM33MF
X
R005
X
Q012
J
JP005
X
JP003
AH
Q011
X
JW25
1
X
JW26
1
X
JW27
1
X
JW28
1
T471
1
2
3
4
5
6
78
9
10
X
JP683
1FJ1
R643
1
2
X
R643A
1
2
CJ56CCA
C525TM
2000KK1000DBH
C616
X
R032TM
L604TM
X
G
+B
R-OUT(21")
G-OUT(14")
9V
G-OUT(21")
R-OUT(14")
ASSY PWB CRT C8YH (1AA4B10S03600)
ASSY,PWB,CRT BA4H (1AA0B10S218KB)
B-OUT
SOCKET
GND
R
GND
HEATER
BB
G
R
KK560
R707
1.2K
R724
1/2DJ2.7K
R716
KK560
C703
5.6K
R743
J10EA050N
K7P
J10KR050N:
B4J10XC050N:
J10EA053N
180
R705
Q705
KTC3229-U-PM
QT0392
1
2
3
470
R701
250EM10CY
C710
:250EM10CX
Q701
KTC3229-U-PM
QTA392
2
3
X
R703
J
D742
J
D741
200KK
470LBZB
R708
J11B2570N
K701L
:J11B3090N
:B4J11B0350N
2
5
6
7
8
9
10
11
J30B0250N
K7U
J30B1380N:
B4J30B0040N
X
R709
X
C701
X
C721
2SA1015O
Q721
:2SA1015Y
1
1/2DJ2.7K
R715
1/2DJ2.7K
R717
KTC3229-U-PM
Q703
QT0392
1
3
180
R702
X
JS741
X
D733
X
C702
X
R706
10
R732
X
D732
X
D731
560
R723
J30B0250N
K7Y
J30B1380N:
B4J30B0040N
L2C1101JN
L702
:L2C1101KN
KK560
C705
J10EA033N
K7Q
:J10KR030N
Q701A
X
2
3
Q705A
X
1
2
3
Q703A
X
1
3
X
K701-M
2
5
6
7
8
9
10
11
2000KK470LBZB
C708
X
C708A
2SJ12K
R713
X
R704
470
R704A
470
R707A
2SJ12K
R712
R711
2SJ12K
C707
KK560
Q901
X
A10B016000
COLOUR TELEVISION
CHASSIS
SERIES
SERVICE
REF. NO.
FFFFCCCC6666----AA
AA
PRODUCT SAFETY NOTICE:
Product safety should be considered when a
component replacement is made in any area
of a receiver.
Components indicated by a mark in this
circuit diagram show components whose
values have special significance to product
safety. It is particularly recommended that only
parts specified on the part service manual be
used for components replacement pointed out
by the mark.
CIRCUIT DIAGRAM NOTICE:
1. All resistance value are in ohms, K=1,000, M=1,000,000.
2. All resistance rated wattages are 1/6W unless otherwise noted.
3. Excepting electrolytic capacitors, all capacitance values of less than 1
are expressed in µ F and more than 1 are pF.
4. All capacitance rated voltages are 50V unless otherwise noted.
5. All inductance values are in µH.
6. Voltage readings take with a "VTVM" are from point indicated chassis
ground. Voltage readings taken by using PALcolour bar signal are
with all controls at normal position. Some voltage may vary with signal
strength.
7. Waveform were taken with PALcolour bar and controls adjusted for
normal picture. Waveforms were taken by using a wide band oscilloscope and a low capacity probe.
8. This circuit diagram covers a basic or representative chassis only.
There
may be some components or partial circuit differences between the
actual chassis and the circuit diagram.
9. Parts specified with "X" are not installed in this model.
10. Parts specified with "J" are just jumper wires.
THE SERVICE PRECAUTION:
The area enclosed by this line( ) is directly connected with AC mains voltage.
When servicing the area, connect an isolating transformer between TV receiver and AC
line to eliminate hazard of electric shock.
11. Expression of capacitance and resistance in circuit diagrme.
BA4H
TRANSISTOR, DIODE AND INTEGRATED CIRCUIT TERMINAL GUIDE
C: COLLECTOR
B: BASE
E: EMITTER
A: ANODE
K: KATHODE
B
B
C
C
E
E
C
E
B
C
E
B
B
C
E
A
K
K
A
A
K
FUSIBLE
RESISTOR
PARTICULAR
PARTS SYMBOL
1
1
1
N/2
N/2 + 1
N
NON POLE
ELECTRIC
CAPACITOR
POSISTER
C
E
B
CHIP
COMPONENTS
K
A
TRANSISTOR
DIODE
123
RESISTOR
12 X 103=12K
Capacitance (Example)
1000
C
M 2000
D
Characteristic
Capacitance value (220pF)
Allowable error (±20%)
Kind (Ceramic)
Rated voltage (1,000V)