1
Do not allow anything to rest on the power
cord.
Do not locate this display where the
cord will be damaged by people walking on
it.
Do not overload wall outlets and extension
cords as this can result in fire or electric
shock.
Slots and openings in the cabinet and in the
back or bottom are provided for ventilation to ensure reliable
operation and to protect it from overheating. These openings
must not be blocked or covered. The opening should never be
covered with a cloth or other material, and the bottom openings
should not be blocked by placing the monitor TV receiver on a
bed, sofa, rug, or other similar surface.
Do not place this monitor television near any heat sources such
as radiators, heaters, stoves and other heat-generating products
(including amplifiers).
Do not place the monitor TV in direct sunlight.
Do not place your monitor TV on an unstable stand, shelf or
table. Serious injury to an individual, and damage to the monitor
TV may result if it should fall.
If the monitor TV is built into a unit, or enclosed, the minimum
distances for ventilation must be maintained. Heat build up can
reduce the life of your monitor TV, and can be dangerous.
This monitor TV should be operated only from the type of power
source indicated on the display unit or as indicated in the
Operating Instructions. If you are not sure of the type of power
supply available , consult your sales person or your local power
company.
Never add accessories that have not been specifically designed
for this monitor television.
Some internal parts carry hazardous voltages and contact may
result in an electric shock hazard.
Never spill liquids of any kind
onto the monitor TV receiver.
Do not place items such as vases
containing liquid on top of the monitor TV.
Do not expose the monitor TV to rain or use near water. For
example, near a bathtub, kitchen sink, in a wet basement, etc.
Do not use immediately after moving the monitor TV from a low
temperature to a high temperature environment, as this causes
condensation, which may result in fire, electric shock, or other
hazards. Before cleaning, unplug the monitor TV from the wall
socket.
Never stand on, lean on or push the monitor TV.
Never allow children to play with the monitor TV
Serious injury may result if it should fall.
Do not apply liquid cleaners or
aerosol cleaners directly onto the
monitor TV receiver. Only use a soft
cloth for cleaning.
Do not place candles or hot objects
upon the monitor TV, next to it or
behind it. Open flames must never be
used near the monitor TV set.
SAFETY
SAFETY
PRECAUTIONS
PRECAUTIONS
Installation
CAUTION: Please read and retain for your safety. This monitor TV has been engineered and manufactured to assure your
personal safety, but improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards
incorporated in this receiver observe the following basic rules for its installation, use and servicing.
Use
CE27LMY1-B
CE32LMY1-B
MINIMUM DISTANCES
10cm
10cm
10cm
: Exit
4cm
: Exit
2
SAFETY
SAFETY
PRECAUTIONS
PRECAUTIONS
Important:
This equipment is fitted with an approved non rewireable UK mains plug. To change a fuse in this type of plug proceed as follows:
1. Remove the fuse cover and fuse.
2. Fit a new fuse which should be a BS1362 5Amp A.S.T.A. or BSI approved type.
3. Ensure that the fuse cover is correctly refitted.
If the fuse cover is lost or damaged the plug must
NOT be used but replaced with a serviceable plug.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug
contains a fuse, this should have a rating of 5 Amp, ensure the fuse cover is correctly fitted. If a plug without a fuse is used, the fuse at
the distribution board should not be greater than 5 Amp.
Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13Amp socket elsewhere.
The wires in this mains lead are coloured in accordance with the following code:
Blue -------> Neutral
Brown ----> Live
1.
The Blue wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK.
2. The Brown wire must be connected to the terminal with the letter “L” or coloured RED.
3. Do not connect either wire to the earth terminal in the symbol or coloured GREEN or GREEN and YELLOW.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the wires.
THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS THE MAINS LEAD IS UNPLUGGED.
Your monitor television is fully transistorised and does not
contain any user serviceable components.
You must not remove the rear cover of the monitor TV by yourself. The apparatus is working with high voltages and could
damage objects or even endanger people. Leave all required
repair and service jobs to an authorised service technician. He
will exclusively use such spare parts that are complying with
the same safety standards as applicable to the original parts.
The use of original spare parts can prevent fire, shock and
other hazards.
Unplug the monitor television receiver from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
■ If the power cord or plug is damaged.
■ If liquid has been spilt into the monitor
television receiver.
■ If monitor television receiver has been exposed to rain or water.
■ If the monitor television receiver has been dropped or the cabinet
has been damaged.
■ If the monitor television receiver exhibits a distinct change in
performance.
■ If the monitor television receiver does not operate normally by
following the operating instructions.
Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in
damage. This will often require extensive work by a qualified
technician to restore the monitor television receiver to normal
operation.
Servicing
Important recycling information.
Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be
disposed of separately.
In the European Union there are separate collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
Note: This symbol mark and recycle system are applied only to EU
countries and are not applied to other countries of the world.
3
1. Connect your aerial cable socket to the back of the LCD TV monitor
set. Fit the aerial cable as shown or as shown below when AV
equipment is connected.
● Connecting DVD / VCR player/ Satellite receiver or
Set top box.
The following examples are our recommended standard connection.
For further information please consult your local dealer.
2. Connect the power cord of the LCD TV to a wall outlet.
■ As this product does not have a mains On/Off switch, please
ensure your mains plug is easily accessible.
■ The monitor TV set is prepared for a mains voltage AC220~240V,
50Hz. To disconnect completely from the mains or, when the monitor TV is not to be used for an extended period of time, it is advisable to disconnect the power cord from the power outlet.
■ For all aerial problems please consult your local dealer.
1. Left side terminals
■ Press the v button on the remote control repeatedly to select
AV1 mode and PC mode. Press and hold down for the AV selection
menu to appear use the e or d buttons to select mode.
PC Connection
This TV set has a PC connector.You
can connect a PC to the LCD TV and
use it as a monitor if required.
This connection is located on the side
terminal.
It is recommended that the PC connection cable should be less than 3m in
length.
INST
INST
ALLA
ALLA
TION
TION
Step : 1 Connections
AV1
WARNING! High voltages are used in the operation of
this set. Refer service to qualified service personnel.
Terminals
As indicated
above
AV1
PC input
PC
I
IN
DVD
AC Mains Outlet
DISH
IN
OUT
IN
4
SPECIFICA
SPECIFICA
TION / HELPFUL
TION / HELPFUL
HINTS/END USER LICENCE
HINTS/END USER LICENCE
Common specification
Power source AC 220~240V 50Hz
Television system System I
Colour system PAL
(PAL/NTSC4.43 in AV mode)
Channel coverage UHF: 21-69.
VHF: A-J,E2-E12
CATV: X, Y, S1-S41
Aerial input impedance 75 ohm
Side AV terminal
AV1: SCART
Input: AV I/O + RGB + YC
PC D-sub 15pin
CE27LMY1-B CE32LMY1-B
Sound output
(Continuous) N/A N/A
Screen (inches/ cm)
(viewing measured
diagonally) 27”/ 68.6cm 32”/ 81cm
Contrast ratio 900:1 1000:1
Display resolution 1366 x 768 (WXGA) 1366 x 768 (WXGA)
Viewing Angles H:176º V:1176º H:176º V:1176º
Dimensions
(W x H x D mm) 702 x 440 x 180.5 819 x 508 x 180.5
Weight (kg) 12.2 15.5
■ POOR PICTURE, SOUND OK
● Adjust BRIGHTNESS control.
● Adjust FINE TUNING control.
● Check aerial connections.
■ NO COLOUR, PICTURE OK
● Adjust COLOUR control.
● Adjust FINE TUNING control.
● Is the programme in colour ?
■ WEAK PICTURE
● Check aerial connections on back of monitor.
● Check aerial for broken wires.
● Re-orient aerial.
The following faults are not caused by the receiver:
"GHOSTS"
Reflections of signals from mountains or high buildings will cause multiple
images, called "Ghosts". These abnormal conditions can be reduced to
minimum by repositioning aerial or by installing new one suited for your
area.
"INTERFERENCE"
Interference may be caused by electrical appliances, car ignition systems, etc. This should normally be a temporary condition, but should this
interference persist, contact your dealer.
The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applications, utilities
and modules embedded within the Product) which is owned by Sanyo or
its licensors. Before using the product, please read the End-User Licence
Conditions detailed below. If you do not agree to the terms and conditions
of the End-User Licence, Please do not proceed to use the Productrepack the Product unused and return it to your supplier together with
proof of purchase for a full refund. By using the product, you agree to be
bound by the terms and conditions of the End-User Licence.
Licence Grant, Conditions and restrictions
1. Sanyo grants you a non-exclusive, world-wide (subject to export controls), non-transferable (except as permitted by 2 below), royalty-free
licence to use the Software upon and with the Product.
2. You may not transfer any of your licence rights in the Software without
the prior written consent of SANYO and if consent is provided then the
Software shall only be transferred in conjunction with the transfer of the
Product AND provided that the transferee has read and agreed to
accept the terms and conditions of this licence.
3. You must ensure that the copyright, trademark and other protective
notices contained in the Software are maintained and not altered or
removed.
4. The Software provided hereunder is copyrighted and licenced (not
sold). SANYO especially does not transfer title or and ownership rights
in the Software to you. The Software provided hereunder may contain
or be derived from portions of materials provided to SANYO under
licence by a third party supplier.
5. Except as expressly permitted by statute
you may not;
● use the Software in conjunction with any other computer hardware
other than the product;
● copy all or part of the Software;
● incorporate all (or any of) the Software into other programs devel-
oped by (or on behalf of) you and/or used by you;
● reverse-engineer, decompile or disassemble the Software;
● make the Software (or any part of it) available, or permit its redistri-
bution, for use with any computer hardware other than the Product;
or rent, lease, gift, loan, sell, distribute or transfer possession of the
whole or any part of the Software.
Termination
This licence is effective until terminated. This licence will terminate automatically without notice if you fail to comply with any of its provisions.
Disclaimer
1. The Software is(to the extent permitted by law) supplied ‘as is’ and
SANYO and its suppliers expressly exclude all warranties, express or
implied, including (but not limited to) warranties of satisfactory quality,
fitness for purpose and non-infringement (save to the extent that the
same are not capable of exclusion at law).
2. In no circumstances will SANYO be liable for any direct, indirect, consequential, or incidental damage (including loss of profits, business interruption, loss of data or the cost of procurement of substitute goods,
technology or services) arising out of the use or the inability to use the
Software (save to the extent that such liability is not capable of exclusion at law).
General
1. This End-User Licence will be governed by laws of England and the
User may only bring claims in the English Courts and SANYO shall be
entitled to bring a claim in the courts of any jurisdiction.
2. The above terms and conditions supersede any prior agreement, oral or
written, between you and SANYO relating to the Software.
Specification
Helpful hints
Part No. 1KA6P1P0307-A N3KJ/LJ
Printed in U.K.
End-User Licence
Loading...