Sanyo CA29YS2S, CP29YS2S, CP29YS2BS, CA29YS2BS Instruction Manual

CA21XS2S
CP21XS2S
CA21YS2S
CP21YS2S
CA21KS2
CP21KS2
CA21KS2K
CP21KS2K
CA21SF1
CP21SF1

Instruction Manual

Colour Television

Flat Screen
Multi System
CATV Hyper Band
256 Programmes with Automatic Tuning
AV Stereo Sound System
DVD Input with Video Component

2

WarningandCaution

If the televi­sion is to be
built into a
compartment
or similarly
enclosed, the
minimum dis­tances must

be maintained.
Heat build-up can reduce the service life of your televi­sion, and can also be dangerous.

Never stand on, lean on or push sud­denly the television or its stand.
You should pay special attention to
children. Serious injury may result if
it should fall.

Do not place your television on an
unstable cart, stand, shelf or table.
Serious injury to an individual, and
damage to the television, may result
if it should fall.

High voltages are used in the operation of this television receiver. Do not
remove the cabinet back from your set. Refer servicing to qualified service
personnel.

To prevent fire or electrical shock hazard, do not expose the television
receiver to rain or moisture. The television shall not be exposed to dripping
or splashing and that no objects filled with liquids, such as vases, shall be
placed on the television.

Do not drop or push objects into the television cabinet slots or openings.
Never spill any kind of liquid on the television receiver.

At installation of the unit, the plug
of power cord shall remain
accessible and readily operable
to disconnect the unit from the
wall outlet.
When the television receiver is
not used for an extended period
of time, it is advisable to discon­nect the AC power cord from the
AC outlet.

Avoid exposing the television
receiver to direct sunlight and
other source of the heat.
Do not stand the television
receiver directly on other prod­ucts which give off heat. E.g.
video cassette players, audio
amplifiers.

Do not block the ventilation holes in
the back cover.
Adequate ventilation is essential to
prevent failure of electrical compo­nents.

Do not squash power supply
cord under the television
receiver.

5cm

10cm

10cm

20cm

Minimum distances

Warning

Caution

Contents

3

Warnings and Cautions . . . . . . . . . . . . . . 2

Contents . . . . . . . . . . . . . . . . . . . . . . . . . 3

Plug & Play . . . . . . . . . . . . . . . . . . . . . . . 3

Front Control . . . . . . . . . . . . . . . . . . . . . 4-5

Remote Control Transmitter . . . . . . . . . . 6

Battery Installation of

the Remote Control Transmitter . . . . . . . 6

General Operation

Remote Control Operation . . . . . . . . . 7

OFF TIMER . . . . . . . . . . . . . . . . . . . . 8

ON TIMER . . . . . . . . . . . . . . . . . . . . . 8

Colour and Sound System

Setting of the Colour System . . . . . . . 8

Setting of the Sound system . . . . . . . . 8-9

Picture Adjustment . . . . . . . . . . . . . . . . . 9-10

Audio Adjustment . . . . . . . . . . . . . . . . . . 10

Tuning of the Channels

Automatic Tuning . . . . . . . . . . . . . . . 11

Semi-Auto Tuning and Manual Tuning

.

.11

Channel Copy . . . . . . . . . . . . . . . . . . 12

Channel Swapping . . . . . . . . . . . . . . 12

Skip Channel Set and Cancel . . . . . . . . . . .12-13

Setting of the Private Position . . . . . . . . 13

Setting of the OSD Language . . . . . . . . . 14

Connecting Other Equipment . . . . . . . . . 14

Connecting to the Rear AV1 Input

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15

Selecting the Colour System in AV

Mode . . . . . . . . . . . . . . . . . . . . . . . .15

Connecting to a DVD Player with AV1(DVD)
Video Component output terminal . . .15

Connection to the Front AV2 Input

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting to the Monitor Output

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

AV Connection to the Aerial Socket . . . . 16

Aerial Connection . . . . . . . . . . . . . . . . . . 17

Care and Cleaning . . . . . . . . . . . . . . . . . . 17

Specifications . . . . . . . . . . . . . . . . . . . . . 18

Helpful

Hints-Problems/Solutions . . . . . . . . . . . 19

Plug&Play

This TV set provides a self-automatic tuning and
sorting system function called “Plug & Play”. It
automatically begins searching and storing of all
available channels when switching-on the TV set
for the first time.

2

Press any of the control buttons to make the
ending message disappear. Or will
automatically return to normal TV display
after 10 seconds.

After completing this procedure, the programme
position 1 is selected and the ending messages on
the screen.

Note: The Plug & Play can be cancelled at any

time by pressing the MENU button.

✐ This procedure only appears at the first

switch-on time.

1

Connect power cord of the TV set to a wall
outlet, and turn on the TV set by pressing the
Mains ON/OFF button. Self-automatic tuning
system will be started as follows;

■ If no TV stations are found, the display shown
below will appear. Please check if the antenna
is connected properly.

If it isn’t connected properly, connect antenna and
Automatic Tuning will be reset.

❒ Automaticsettingupchannels

❒ Let’sStart!

I AM SEARCHING.

ALL PROGRAMMES.

PLEASE WAIT.

1

AUTO SET-UP

COMPLETED.

HAPPY VIEWING !

NO STATION.

PLEASE CONNECT

ANTENNA PLUG.

4

Model CA21XS2S, CP21XS2S

FrontControl

Each button listed in this section has the same function as it’s corresponding

button on the remote control.

123

6789

4510

Model CA21YS2S, CP21YS2S

Press to open

Press to open

123

67 45

8910

1. Mains ON/OFF Button

2. Remote Control Detector

3. Stand-by and Power Indicator

4. Programme UP/DOWN

5. VOLUME

6. MENU

7. TV/AV Selector

8. Audio Input Jack-Right (AV2)

9. Audio Input Jack-Left (AV2)

10. Video Input Jack (AV2)

VIDEO

L-AUDIO-R

TV/AV MENU - + CH

AV2 IN

VIDEO

L-AUDIO-R

TV/AV MENU - + CH

5

Model CA21KS2, CP21KS2, CA21KS2K, CP21KS2K

FrontControl

Each button listed in this section has the same function as it’s corresponding

button on the remote control.

123

4

5

67

8910

1. Mains ON/OFF Button

2. Remote Control Detector

3. Stand-by and Power Indicator

4. Programme UP/DOWN

5. VOLUME

6. MENU

7. TV/AV Selector

8. Audio Input Jack-Right (AV2)

9. Audio Input Jack-Left (AV2)

10. Video Input Jack (AV2)

Model CA21SF1, CP21SF1

123

4

5

67

Pull to open

T

V

/

A

V

M

E

N

U

­+

C

H

P

O

W

E

R

VIDEO

L-AUDIO-R

T

V

/

A

V

M

E

N

U

­+

CH

P

O

W

E

R

6

RemoteControlTransmitter

-/- -

Power ON/OFF button

ALTERNATE button

VOLUME + button

TIMER button

MUTE button

CHANNEL SCAN button

SURROUND button

PICTURE MODE button

Programme UP button

RECALL/COLOUR SYSTEM button

MENU button

TV / AV Selector button

Programme Selector button

SWAP button

VOLUME - button

STEREO/MONO button

Programme DOWN button

BASS EXPANDER button

SOUND MODE button

SOUND SYSTEM button

DIGIT button

❒ BatteryInstallationoftheRemoteControlTransmitter

1. Open the battery cover.

2. Install two “AA” 1.5 volt batteries so that the “+” and “-” marks on the batteries match the “+” and

“ - ” marks inside the unit.

3. Close the battery cover.

Note: Replace the batteries when the TV set is showing the following symptoms:

Operation is unsteady or erratic, sometimes the TV set does not work with transmitter.
Discharged batteries may leak and damage the unit. The normal life of batteries should be from
nine to ten months.

TV / AV

-/- -

SWAP

TIMER

CH

P

CH SCAN

P

A•B

BASS

MENU

SOUND

CH

JXPSG

S. SYS

PICTURE

SURROUND

7

GeneralOperation

Standby/Power-on

To switch the TV on and off. For shutting off a power supply completely, Press the Mains
ON/OFF button on the front control of TV set.

Soundmute
To switch the sound from the speakers. The sound changes as follows; normal→mute ().

TIMER

Timer
To Adjust Timer function OFF-TIMER→ONTIMER→ONPROGRAM

Recall/Coloursystemselector

To display the programme information on the screen.
It also operates as Colour system selector if the clear picture cannot be obtained even when
the broadcasting or AV signal is received.
Colour System and Sound System (SIF) could be changed in SEMI-AUTO and MANUAL TUN­ING operation.

-/- --/- -

Directprogrammeselector

For direct access to programmes using the (0-9)numeric button. For selection of analogue
programme position 10 - 255, Example: for programme position 17,

Press

the Digit button,

press

“1” button. Press “7” button. For programme position 125

Press the Digit button twice. Press “2” button.

Press “5” button.

For programme position 225

Press the Digit button 3 times. Press “2” button. Press

“5” button.

P

P

Alternate

To select the previous position and the present position.

-/- -

VolumeUp/Down

To adjust the sound volume level . Also operates as left ( ) and right ( ) cursor.

-/- -

-/- -

Programmedown/up

To select the next programme number or previous programme number. Also operates as up
() and down ( ) cursor.

-/- -

SWAP

Swap

To swap the channels between two stored programme positions

SOUND

SoundMode

To select Sound mode; PERSONAL, MUSIC, TALK, NORMAL.

PICTURE

PictureMode

To select Picture mode; PERSONAL, DYNAMIC, NATURAL, ECO, GAME.

-/- -

BASS

BassExpander

To activate bass expander function.

S. SYS

SoundSystem

To select optimum sound system (BG → I → DK → M).

SURROUND

Surround

To activate Surround function.

MENU

Menu

To Call up the TV MENU.

-/- -

A•B

Stereo/Mono Button

❒ RemoteControlOperation

CH

CH

8

GeneralOperation

■

■ If no operation is performed after the TV has

been switched on by the ON TIMER, such as if
you are not at home, the TV will be
automatically switched off after approximately
2 hours

■

■ If the TV is already switched on when the time

set for the ON TIMER has been reached, only
the programme position will be changed to the
set programme position.

■

■ Cancelling ON TIMER. To cancel the ON

TIMER, press the VOLUME ( + or - ) button to
set it to “ON 0:00” while the ON TIMER screen is
shown. Switching off the TV by pressing the
Mains ON/OFF button will also cancel the ON
TIMER settings.

The OFF TIMER will switch off the TV automatical­ly after 30 minutes, 1 hour, 1 hour and 30 minutes,
or 2 hours.

■ Just one minute before switching off the TV,
“OFF 0:01” will be display on the screen.

■ To cancel the OFF TIMER, select “OFF 0:00”
by pressing the VOLUME (+ or - ) button.

■ The OFF TIMER cancels when the TV set is
turned off or if a power failure occurs.

When the ON TIMER is set. TV will automatically
be switched On to the selected programme position
when the specified time has elapsed.

Programme position for when TV is
switched ON by ON TIMER.

❒ OffTimer

1

Press the TIMER button.

OFF 0:00

2

Press the VOLUME ( + or - ) button to select
the time period.

❒ OnTimer

1

Press the TIMER button twice.

ON 0:00 2

(ON TIMER setting mode)

2

Press the VOLUME ( + or - ) button. The set
time will be increased or decreased by 10
minutes each time the button is pressed ; the
maximum time which can be set is 24 hours.

3

Use Direct Programme Selection to insert
programme position for when TV is switched
on by ON TIMER. (see page 7.)

❒ OnTimer(Continued)

Normally, set the colour system to “AUTO”, if the
clear picture cannot be obtained even when the
broadcasting or AV signal is received, press the
RECALL/COLOUR SYSTEM button repeatedly
until the optimum image can be produced.
(Refer to Broadcast Transmission System List
indicated by the last of this page in a setup of
Colour System.)

Each time the RECALL/COLOUR SYSTEM but­ton is pressed, colour system changes as follows;

To set the sound system, make it during Semi-Auto
Tuning or Manual Tuning mode.
When the sound is not clear or no sound is pro­duced on a programme number position, select
sound system repeatedly until the optimum sound
is obtained.
(Refer to Broadcast Transmission System List
indicated by the last of this page in a setup of
Sound System.)

To select sound system:

■ Press the SOUND SYSTEM button to select the

sound system directly. The sound system will be
memorized automatically.

Note:Colour system is displayed according as
Colour system option.

6

AUTO

6

PAL

6

NTSC

6

NTSC4.43

ColourandSoundSystem

❒ SettingoftheColourSystem

❒ SettingoftheSoundSystem

or:

1) Select “SIF” with the Programme UP or
DOWN button in the Semi-auto or Manual
Tuning mode. Then press the VOLUME (+ or

-

) button to select a optimum sound system.

9

ColourandSoundSystem

❒ SettingoftheSoundSystem

BG

(5.5MHz)

DK

(6.5MHz)

I

(6.0MHz)

M

(4.5MHz)

2) To enter a sound system selection into the
memory, select “MEMORY” and press the
VOLUME + or -button.

(Semi-Auto or Manual Tuning mode )

SIF

BG

MEMORY

OK

Broadcast Transmission System List

Area

Country

Sound

System

Colour

System

Middle

East

Asia

Oceania

PAL

B/G

Australia,
New Zealand, etc.

Union of Arab Emirates,
Kuwait, Oman, Qatar,
Yemen,

Bahrain,

etc.
Indonesia, Malaysia,
Singapore, Thailand,

etc.

PAL

B/G

China,

etc.

PAL

D/K

Hong kong

PAL

I

Saudi Arabia,
Iraq, Iran, Lebanon,etc.

B/G

SECAM

Russian Federation,etc.

D/K

SECAM

Myanmar, etc.

M

NTSC

PictureAdjustment

The 2nd page is not displayed when there is no
TINT adjustment.

COLOUR

Page 1

Page 2

WHITE TONE

❒ PictureAdjustmentMenu

SHARPNESS : Adjusts picture detail.
WHITE TONE : Adjusts white balance.
FINE TUNING : Fine tuning in case of weak

broadcast signal or poor reception. Only
displayed in TV mode. Will not be displayed in
AV mode.

Picture Adjustment Item

COLOUR : Adjusts colour intensity.
BRIGHT : Adjusts picture brightness.
CONTRAST : Adjusts picture contrast.
TINT : Adjust colour tints. (Displayed only on

NTSC or NTSC4.43 system signal
reception.)

(MAIN MENU)

PICTURE

❒ BasicPictureAdjustmentOperation

1

Press the MENU button for MAIN menu
display.

MODE

SEARCH

POSITION

SYSTEM

SKIP

MEMORY

SELECT

SEMI
START

2

AUTO

OFF

--

ADJUST

BACK

EXIT

MODE
SEARCH
POSITION
SYSTEM

SIF
SKIP

SEMI
START

2
AUTO
BG
OFF

SELECT

ADJUST

BACK

EXIT

BRIGHTNESS
CONTRAST
TINT
SHARPNESS

SELECT

ADJUST

40

FINE TUNING

BACK

EXIT

SELECT

ADJUST

BACK

EXIT

AUDIO
PRESET
LANGUAGE

SELECT

ENTER

EXIT

10

PictureAdjustment

❒ BasicPictureAdjustmentOperation(Continued)

■ To return to the normal TV mode, press the

MENU button. ( Or will automatically return to
the normal TV mode after 20 seconds.)

PICTURE

COLOUR

BRIGHTNESS

2

When “PICTURE” is not selected, select
“PICTURE” with the Programme UP or
DOWN button.

3

Press the VOLUME + or-button to display
Picture Adjustment menu.

4

Select desired control by pressing the
Programme UP or DOWN button

5

Press the VOLUME + or-button to alter
settings.

■ To return to Main menu, press the

ALTERNATE button.

Audio Adjustment Item

BASS : Bass Adjustment

TREBLE :Treble Adjustment

BALANCE : Left/right speaker volume balance

adjustment

BASS EXPANDER : Operates BASS EXPANDER

on and off

SURROUND :Operates SURROUND on and off.
Note: When the stereo signal is inputted from the

right and left audio input terminals in the AV mode,
surround mode is changed as follows;
“SURROUND” ON and “SURROUND OFF”.

■

■ To return to Main menu, press the ALTERNATE

button.

■

■ To return to normal TV mode, press the MENU

button. (Or will automatically return to normal
TV mode after 20 seconds.)

BASS

AUDIO

BASS

AudioAdjustment

❒ AudioAdjustmentMenu

❒ AudioAdjustmentOperation

1

Press the MENU button for MAIN menu
diplay.

2

Select “AUDIO “ by pressing the Programme
UP or DOWN button.

3

Press the VOLUME + or-button for Audio
Adjustment menu display.

AUDIO
PRESET
LANGUAGE

BRIGHTNESS

CONTRAST

SHARPNESS
WHITE TONE
FINE TUNING

25

COLOUR

CONTRAST
SHARPNESS
WHITE TONE
FINE TUNING

30

TREBLE

BALANCE

BASS EXPANDER
SURROUND

SELECT

OFF

ADJUST

OFF

27

BACK

EXIT

PICTURE

PRESET
LANGUAGE

TREBLE
BALANCE
BASS EXPANDER
SURROUND

OFF

OFF

27

11

TuningoftheChannels

Up to 256 broadcast stations in your reception
area can be stored in the electronic memory.

There are three ways of tuning as follows;

1. Automatic Tuning (the basic way):

All receivable channels are automatically tuned
in and memorized in consecutive programme
position.

2. Semi-Auto Tuning:

Use to preset a receivable channel in any
desired programme position, e.g. the position
with the same number as the channel.

3. Manual Tuning:

Manually tune a channel if it cannot be
automatically tuned, such as when the signal is
poor.

■

■ The Automatic Tuning operation can be

cancelled at any time by pressing the
Programme UP or DOWN button.

After all receivable channels have been found and
stored, the TV set automatically returns to pro­gramme position “1”.

-/- -

MENU

CH

CH

1

PRESET

SEARCH

START

MODE

AUTO

❒ AutomaticTuning

1

Press the MENU button for MAIN menu
display.

2

Select “PRESET” by pressing the
Programme UP or DOWN button

.

3

Press the VOLUME + or

-

button for
PRESET menu display. On entering PRESET
display, Automatic Tuning will be selected
initially.

4

Select “SEARCH” by pressing the
Programme UP or DOWN button.

5

Press the VOLUME (+) button to start
channel tuning

.

The VOLUME + button will move tuning toward the
higher frequencies, and the VOLUME - button will
move tuning toward the lower frequencies.

Semi-Auto Tuning:

Press and release the VOLUME + or - button
to search for required TV station. Once a station
is located, tuning will automatically stop.
Continue till desired channel is located.

Manual Tuning :

Press and hold the VOLUME + or

-

button to

search for required TV station.

To preset other Programme Positions, repeat steps
5

-

7.

SEARCH

START

SEARCH

SEARCH

MEMORY

OK

❒ Semi-AutoTuningandManualTuning

1

Press the MENU button for MAIN menu
display.

2

Select “PRESET” by pressing the
Programme UP or DOWN button.

3

Press the VOLUME + or

-

button for
PRESET menu display. On entering
PRESET display, Automatic Tuning will be

selected initially.

4

Select “SEMI” or “MANUAL” by pressing the

VOLUME + or

-

button.

5

Select “SEARCH” by pressing the
Programme UP or DOWN button.

6

Once desired channel is located, select
“MEMORY” by pressing the Programme UP

or DOWN button.

7

Press the VOLUME + or-button to enter the
desired channel into memory.

8

Press the MENU button to return to normal
TV display.

PICTURE
AUDIO

LANGUAGE

SEARCH

POSITION

SYSTEM
SIF

MODE

POSITION

SYSTEM
SIF

START

1
AUTO
BG

AUTO

1
AUTO
BG

MODE

POSITION
SYSTEM

MODE

POSITION
SYSTEM

MODE

POSITION
SYSTEM

SKIP

SEMI

6

AUTO

SEMI

6

AUTO

MANUAL

6

AUTO

OFF

SELECT

ADJUST

BACK

EXIT

12

This function can be utilized after Automatic
Tuning.

For example, to copy a TV channel on pro­gramme position “2” onto programme position
“6”;

2

Use this channel swapping feature to swap the
channels between two stored programme position.
This feature is particularly useful after automatic
tuning.

For example, to swap the channel between pro­gramme position “6” and programme position
“12”.

6

12

POSITION

6

❒ ChannelCopy

1

Select programme position “2”

2

Enter to SEMI-AUTO or MANUAL tuning
mode. (Refer to page 11.)

3

Select “POSITION” with the Programme UP
or DOWN button.

4

Select position “6” with the VOLUME + or

-

button.

5

Select “MEMORY” by pressing the
Programme UP or DOWN button.

6

Press the VOLUME + or

-

button to

memorize.

7

Press the MENU button to return to normal
TV display.

❒ ChannelSwapping

1

Select programme position “6”.

6

2

Press the SWAP button.

SWAP 6 AND

-

The two TV channels will now have changed
places.

6

12

SWAP 6 AND 12

6

SWAPPING

3

Press the DIGIT button, “ 1 “ button and then
“ 2 ” button on the remote control to enter
programme number 12. (For example, to
enter programme number “ 3 “, press “ 3 ”
button only. )

When there is a position you do not use, Position 4
for example, by setting the SKIP Channel function it
is possible to jump over this position, when you are
selecting a channel using the Programme

UP/DOWN or CHANNEL SCAN button.

3

4

5

Skip

For example, to set programme position “4” as
Skip channel ;

POSITION

4

❒ SkipChannelSetandcancel

1

Enter to SEMI-AUTO or MANUAL tuning
mode. (Refer to page 11.)

2

Select “POSITION” with the Programme UP
or DOWN button.

3

Press remote control “4” button to select
programme position 4. Use the DIGIT button
and Programme Selector (Number buttons)
to enter programme number. Do not use the

VOLUME + or

-

button to enter programme

position in this settings.

MODE
SEARCH

SYSTEM

SEMI
START

AUTO

MODE
SEARCH

SYSTEM
SIF
SKIP
MEMORY

SEMI
START

AUTO
BG
OFF

--

13

Any number of channels maybe set as Skip
Channels.

SKIP

ON

MEMORY

OK

4

Select “SKIP” by pressing the Programme UP
or DOWN button,then press the VOLUME +
or

-

button to set SKIP to ON. To cancel Skip

Channel function, set to OFF.

❒ SkipChannelSetandcancel(Continued)

5

Select “MEMORY” by pressing the
Programme UP or DOWN button, then press
the VOLUME + or-button for memory.

6

Press the MENU button to return to normal
TV display.

SettingofthePrivatePosistion

For example, to set the programme position
“15” as the private position.

The programme number “15” will shift to centre of
the screen.

The picture will disappear, and “ 15” will be dis­play on the screen.

The private position setting is now completed.

Private position is used to restrict of pro­gramme positions that you do not want others
to watch. Any position can be set as the Private
position.

15

15

15

AUTO

BG

BG

AUTO

15

❒ HowToSetthePrivatePosition

1

Select programme position “15”.

2

Press and hold the RECALL/COLOUR
SYSTEM button for more than 2 seconds

3

Press the MENU button.

15

Note: The position “15” is still in the private position.

15

AUTO

BG

The private position is now cancelled.

15

❒ ToViewaProgrammeonPrivatePosition

1

Select private position (In this case position “15”).

2

Press and hold the RECALL/COLOUR
SYSTEM button for more than 2 seconds.

3

Press the RECALL/COLOUR SYSTEM
button for watching a TV programme.

❒ CancellingofthePrivatePosition

1

Select private position (position “15”).

2

Press and hold the RECALL/COLOUR
SYSTEM button for more than 2 seconds.

3

Press the MENU button.

15

15

AUTO

BG

15

MODE
SEARCH
POSITION
SYSTEM
SIF

MEMORY

SELECT

SEMI
START

AUTO
BG

--

ADJUST

4

BACK

EXIT

MODE
SEARCH
POSITION
SYSTEM

SIF
SKIP

SEMI
START

4

AUTO

BG

ON

14

SettingoftheOSDLanguage

Select “ENGLISH”, “ ”, “ ”,
“ ”, “FRANÇAIS”, “PORTUGUES” by

pressing the

Programme

UP or DOWN button. To

return to the normal TV mode, press the MENU
button.

ENGLI SH

ENG LISH

PICTURE

LANGUAGE

EN GLISH

1

Press the MENU button for MAIN menu
display.

2

Select “LANGUAGE “ by pressing the
programme UP or DOWN button.

3

Press the VOLUME + or

-

button for

Language menu display.

4

Press the MENU button to return to normal
TV display.

ConnectingOtherEquipment

❒ ConnectingTotheRearAV1InputJacks

■ When a monophonic video recorder is

connected to this product, connect the audio
output terminal of the video recorder to the L(left)
audio input terminal of the TV set.

Connecting to a Monophonic Video Recorder (AV1)

■ When the audio signal from the VCR is stereo,
be sure to connect the right and left channels to
the respective right and left AUDIO IN terminals.
Then select “STEREO” channel of the audio
channel in the TV set with the remote control

button.Each time the button is

pressed, the AV Stereo mode is changed as follow,

A B

A B

Note: The effect of surround is not obtained

although the switching of surround is displayed
in this monaural connection.

■ When the stereo signal is inputted from the right
and left audio input terminals, each time the
SURROUND button is pressed (or selection of
On-screen Menu), surround mode is changed
as follows; “ SURROUND ON” and
“SURROUND OFF”.

■

■ To watch

video input
picture,
select AV1
position by
pressing
the TV/AV

Selector.

AV1

■ To make sure the colour system of the TV set

is consistent with the signal of your video
recorder, if necessary, select a matching
system. The colour system set in AV mode
can be stored automatically.

STEREO

MONO

You may connect the audio and video output terminals of the DVD player or VIDEO recorder to the input
terminals of the TV set to enjoy the DVD and VIDEO programs.

SURROUND OFF

SURROUND ON

AUDIO

PRESET

LANGUAGE

PICTURE
AUDIO
PRESET

y

PCC
FRANCAIS
PORTUGUES

y

P

C

C

NN

NN

To Audio Input-R (AV1)

To Audio Input-L (AV1)

To Video Input (AV1)

AV1/DVD

C

R

C

B

Y

INPUT

VIDEO

R

(MONO)

L

MONITOR OUT

R

L

V
I
D
E
O

Video/DVD Player

15

■

■ When watching a video program input from the AV1 terminal, press the TV/AV button to select AV1.

Whenever the TV/AV button is pressed, the mode will change as follows:

■

■ You can select a TV programme while watching a playback from a VCR

For example:

● To select programme position “9” while watching a playback from external VCR, press “9” button of the

remote control. The TV set returns to the TV mode and programme “9” will be selected.

● To select the programme position “26”, press Digit (--/-) button, “2” then “6” button. Then TV set returns

to the TV mode and programme position “26” will be selected.

Note: Pressing either of the PROGRAMME UP or DOWN buttons of the remote control or the TV will

return the TV to the TV mode.

TV mode

AV1

AV1(DVD)

28

AV2

❒ ConnectingTotheRearAV1InputJacks(Continued)

Colour system setting for AV position is automatically stored in the memory.

Each time the RECALL/COLOUR SYSTEM button is pressed, colour system is changed as follow;

Depending on the type of video tape or connected AV equipment being used, it may be necessary to
select colour system. In this case, press the RECALL/COLOUR SYSTEM button and select a suitable
colour system.

Connect the component output terminal on
your DVD player to the component video input
terminal of this product. (NOTE: When a sig­nal of Y,Cb,Cr/Y,Pb,Pr is received, the output
signal from monitor output terminal will be cor­responding but without colour (black and
white image).)

■

■ To watch a program in this connection

status, select AV1(DVD).

28

AV1 AV1(DVD)

(TV mode)

AV2

(Optional

model)

■

■ Make sure the component video terminal (Y, C

b or Cr)

is connected correctly.

❒ SelectingtheColourSysteminAVMode

❒ Connecting To a DVD Player with AV1(DVD) Video Component Input

Terminal(Y,CborCr)

(Optional

model)

AV1

AUTO

AV1

PAL

AV1

NTSC

AV1

NTSC 4.43

To Input Terminal C

To Input Terminal CB

To Input Terminal Y

INPUT

AV1/DVD

C

R

R

C

B

Y

VIDEO

MONITOR OUT

R

To Audio Input-R (AV1)

(MONO)

L

To Audio Input-L (AV1)

Video/DVD Player

R

L

V
I
D
E
O

16

Aerial Socket

The AV apparatus can also be connected to the aerial socket of your TV receiver.

Presetting to watch the video input

1. Playback the VCR .

2. Tune a VCR playback in programme position

that you want. (See Semi-Auto Tuning and
Manual Tuning on pages 11.)

For further details concerning this connection and adjustment, refer to the operating instructions
for the AV equipment.

VCR for

playback

PLAYBACK

■

■ To record TV programme, select TV mode by

pressing the TV/AV Selector and record the
desired programme.

15

The picture signal being displayed on the TV screen is
output through the Monitor Output Jacks. Use these
terminals to record TV broadcasts and for video dub­bing from AV1 or AV2 input terminals.

TV mode

To video and

audio inputs

It is convenient to use the AV input jack on the front panel for equipment
that is often connected and disconnected.

AV2

■

■

To watch the Front AV2 video
input picture, select AV2

position by pressing the TV/AV
Selector.

■ To dub video from the AV1 terminal input, select

AV1 position and by pressing the TV/AV Selector.

AV1

❒ ConnectingTotheFrontAV2InputJacks(OptionalModel)

❒ ConnectingTotheMonitorOutputJacks

❒ AVConnectionTotheAerialSocket

* Model CA21SF1, CP21SF1 are not equipped with Front AV2 input terminal.

To Video Input (AV2)

To Audio Input-L (AV2)

To Audio Input-R (AV2)

Video/DVD Player

INPUT

AV1/DVD

C

R

C

B

Y

VIDEO

R

(MONO)

L

MONITOR OUT

R

L

V
I
D
E
O

To Audio Output-R

To Audio Output-L

To Video Output

VCR for Recording

17

The surface of the cabinet can be damaged if not properly maintained. Many common household aerosol
sprays, cleaning agents, solvents and polishes will cause permanent damage to the fine surface.

1. Unplug the power cord before cleaning the Television.

2. Clean the screen with a soft cloth dampened with glass cleaner or warm water.

3. Clean the cabinet with a soft cloth dampened with a mild household detergent and warm water. Dry

thoroughly.

Note: NEVER spray liquids on the screen because they can run down and drip onto the chassis. This

may cause component failure not covered under Warranty.

Connect the cable with a plug from a UHF (or VHF) aerial to the aerial socket on the cabinet back.

Aerial Cable

Aerial Socket

For all aerial circuit problems please consult your local dealer.

Outdoor Aerial

AerialConnection

❒ ConnectingOutdoorAerial

CareandCleaning

18

Power Source AC 127-240 Volts, 50/60Hz

Colour System PAL/NTSC4.43/NTSC/PAL-60Hz

Sound System B/G, I, D/KK’, M/M

Channel Coverage

VHF: E2-E12, A2-A13, R1-R12, J1-J12, K1-K9
UHF: 21-69, A14-A69, J13-J62,
CATV: S1

-

S41, X, Y, Z, Z+1, Z+2

Aerial input impedance 75 Ω

Audio output (RMS) Model: CA21YS2S, CP21YS2S, CA21KS2, CP21KS2, CA21SF1,

CP21SF1, CA21KS2K, CP21KS2K: 5W + 5W

Model: CA21XS2S, CP21XS2S: 10W + 10W

Speakers Model: CA21YS2S, CP21YS2S, CA21KS2, CP21KS2, CA21SF1,

CP21SF1, CA21KS2K, CP21KS2K: 5 cmx 9 cm x 2 pcs

Model: CA21XS2S, CP21XS2S: 6 cm x 12 cm x 2 pcs

Ext. terminals

DVD Video Component: Composite/Component Y, CB,CR input
Video Inputs: Phone Jack x 2 (1.0Vp-p, impedance 75 Ω) *
Audio Inputs: Phone Jack (L/R) x 2 (436mVrms, impedance more than 40KΩ) *
Video monitor outputs: Phone Jack x 1 (1.0Vp-p, impedance 75 Ω)
Audio monitor outputs: Phone Jack (L/R) x 1 (436mVrms, impedance less than 600Ω)

* Model CA21SF1, CP21SF1 are not equipped with Front AV2 input terminal.

Dimension: Model CA21SF1, CP21SF1:

580(W) x 465(H) x 381(D) mm

Model

CA21KS2, CP21KS2, CA21KS2K, CP21KS2K: 580(W) x 465(H) x 326(D) mm

Model

CA21YS2S, CP21YS2S: 598(W) x 465(H) x 396(D) mm

Model

CA21XS2S, CP21XS2S: 654(W) x 467(H) x 385(D) mm

Weight: Model CA21SF1, CP21SF1: approx. 20.0 Kg

Model

CA21KS2, CP21KS2, CA21KS2K, CP21KS2K

: approx. 19.7 Kg

Model

CA21YS2S, CP21YS2S

: approx. 20.1 Kg

Model

CA21XS2S, CP21XSS

: approx. 19.6 Kg

Specifications subject to change without notice.

Specifications

19

Before requesting service check the following chart.

“GHOSTS”

Reflections of signals from mountains or high buildings will cause multiple images, called “Ghosts”.
These abnormal conditions can be reduced to minimum by repositioning aerial or by installing new one
suited for your area.

“INTERFERENCE”

Interference may be caused by electrical appliances, car ignition systems, etc. This should normally be
a temporary condition, but should this interference persist, contact your dealer.

The following faults are not caused by the receiver:

● Check aerial connection on back of TV set.

● Check aerial for broken wires. ● Re-orient aerial.

Problem: Check these Conditions / Try these solutions:

● Check if TV is plugged in.

● Try a different channel, if OK, probably station trouble.

No picture,
no sound

● Adjust Brightness or Contrast control.

● Adjust Fine Tuning. (See page 9.) ● Check aerial connection.

Poor picture,
sound OK

No colour,
Picture OK

● Adjust Colour or Tint control. ● Adjust Fine Tuning. (See page 9.)

●

Check aerial connection.● Is the programme in colour ? Try a different channel.

● Select other colour system. (See Setting of the Colour System on page 8.)

Weak picture

No sound or poor
sound.

●

Sound Mute may be on. Press the

SOUND MUTE

button on the remote control.

● Adjust Volume. ●

May be station trouble. Try a different channel.

● Select other sound system. (See Setting of the Sound System on page 8-9.)

Remote Control
will not work.

● Check batteries. Replace batteries.

● Check if TV set is plugged in. Aim remote control towards front of TV.

Cannot select or
scan some channels.

● Channel may be removed from memory. Add channel to memory manually.
(See “Skip Channel Set and Cancel” on page 12-13.)

● Check aerial connection.

● This is a normal condition during warm-up and cool down of the plastic

cabinet parts.

Blue screen with AV1
or AV1(DVD) or AV2
is displayed.

● Check AV connection. Press the TV/AV Selection button.

● Check external equipment. Switch on external equipment.

● Check to see if channel is set as the Private Position. See “Setting of the

Private Position” on page 13.

Black screen with
and programme
position displayed.

Cabinet makes
popping sound.

Colour Spot On
The CRT

● Keep away your TV set from magnetic source, then turn-off your TV set and
disconnect TV's power cord from AC outlet, keep this condition about 30-60
minutes and turn-on again your TV set if time is reach. If colour spot is not
disappear after this solution have done, please contact your local dealer.

“SLANT”

If the picture of TV set is not properly horizontal (slant), try to change face direction of your TV set. This
case may be caused by geo-magnetic on your place where you live.

HelpfulHints-Problems/Solutions

SANYO ELECTRIC Co., Ltd.

Part No. 1AA6P1P5578-A BE4D-A (FC8-A)