Sanyo CP14G1(C), CA14G1C, CP14SA1(C), CP14SR1(C), CP21G1(C) Instruction Manual

CP14G1(C)
CA14G1C
CP14SA1(C)
CP14SR1(C)
CP20SR1(C)
CP21G1(C)
CA21G1C
CP21SA1(C)
CA21SA1C

INSTRUCTION MANUAL

Colour Television

Multi System
CATV Hyper Band
256 Programmes with Automatic Tuning

2

Warnings and Cautions

If the television is to be built into a compartment or
similarly enclosed, the minimum distances must
be maintained. Heat build-up can reduce the ser­vice life of your television, and can also be dan­gerous.

Never stand on, lean on or push suddenly the tele­vision or its stand.
You should pay special attention to children.
Serious injury may result if it should fall.

Do not place your television on an unstable cart,
stand, shelf or table. Serious injury to an individual,
and damage to the television, may result if it
should fall.

When the television receiver is not used for an
extended period of time, it is advisable to discon­nect the AC power cord from the AC outlet.

Avoid exposing the television receiver to direct
sunlight and other source of the heat.
Do not stand the television receiver directly on
other products which give off heat. E.g. video cas­sette players, audio amplifiers.

Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure
of electrical components.

Do not squash power supply cord under the tele­vision receiver.

Warning

High voltages are used in the operation of this
television receiver. Do not remove the cabinet
back from your set. Refer servicing to qualified
service personnel.

To prevent fire or electrical shock hazard, do
not expose the television receiver to rain or
moisture.

Do not drop or push objects into the television
cabinet slots or openings.
Never spill any kind of liquid on the television
receiver.

Caution

Warning

Warning

Caution

Caution

Caution

Caution

Caution

Minimum distances

Caution

20cm

10cm

10cm

5cm

If it isn’t connected properly, connect antenna and
Automatic Tuning will be reset.

3

Warnings and Cautions . . . . . . . . . . . . . . 2

Contents . . . . . . . . . . . . . . . . . . . . . . . . . 3

Plug & Play . . . . . . . . . . . . . . . . . . . . . . . 3

Aerial Connection . . . . . . . . . . . . . . . . . . 4

Front Control . . . . . . . . . . . . . . . . . . . . . 4-5

Remote Control Transmitter . . . . . . . . . . 6

Battery Installation of

the Remote Control Transmitter . . . . . . . 6

General Operation

Power ON/OFF . . . . . . . . . . . . . . . . . 7

Auto Shut Off Function . . . . . . . . . . . 7

Direct Programme Selection . . . . . . . 7

Programme UP and Down . . . . . . . . . 7

Channel Scanning . . . . . . . . . . . . . . . 7

Volume Control . . . . . . . . . . . . . . . . . 7

Recall . . . . . . . . . . . . . . . . . . . . . . . . 7

Sound Mute . . . . . . . . . . . . . . . . . . . 7

Alternate . . . . . . . . . . . . . . . . . . . . . . 8

Quick Picture Controls . . . . . . . . . . . . 8

Off Timer . . . . . . . . . . . . . . . . . . . . . . 8

On Timer . . . . . . . . . . . . . . . . . . . . . . 8

Colour and Sound System

Setting of the Colour System . . . . . . . 8

Setting of the Sound System . . . . . . . 8-9

Picture Adjustment . . . . . . . . . . . . . . . . . 9

Basic Picture Adjustment Operation . . 9-10

Tuning of the Channels

Automatic Tuning . . . . . . . . . . . . . . . 10-11

Semi-auto Tuning and Manual Tuning

. .

11

Channel Copy . . . . . . . . . . . . . . . . . . 11

Channel Swapping . . . . . . . . . . . . . . 12

Skip Channel Set and Cancel . . . . . . 12

Setting of the Private Position . . . . . . . . 13

Setting of the OSD Language . . . . . . . . . 13

Connecting other Equipment . . . . . . . . . 14

Connecting to the Rear AV Input

Jacks . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting to the Front AV Input

Jacks . . . . . . . . . . . . . . . . . . . . . . . . 14

Selecting the Colour System in AV

Mode . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting to the Monitor Output Jacks 15
AV Connection to the Aerial Socket . . 15

Care and Cleaning . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . 17

Helpful

Hints-Problems/Solutions . . . . . . . . . . . 18

Plug & PlayContents

This TV set provides a self-automatic tuning and
sorting system function called “Plug & Play”. It
automatically begins searching and storing of all
available channels when switching-on the TV set
for the first time.

2

Press any of the control buttons to make the
ending message disappear, or will
automatically return to normal TV display
after 10 seconds.

After completing this procedure, the programme
position 1 is selected and the ending messages on
the screen.

Note: The Plug & Play can be cancelled at any

time by pressing the MENU button.

✐ This procedure only appears at the first

switch-on time.

1

Connect power cord of the TV set to a wall
outlet, and turn on the TV set by pressing the
Mains ON/OFF button. Self-automatic tuning
system will be started as follows;

Let’s start !

■ If no TV stations are found, the display shown

below will appear. Please check if the antenna
is connected properly.

Automatic setting up channels

Note: For model CA14G1C, CA21G1C,

CA21SA1C only.
For position 1 through to position 30, the picture
settings (Colour, Brightness and Contrast) and the
volume level that you choose can be stored sepa­rately in memory for each position. Thus you can
enjoy watching TV channels with optimum picture
and volume settings, even if you change from one
channel to another.

Multi Personal Preference Level

I AM SEARCHING
ALL PROGRAMMES.
PLEASE WAIT.

1

AUTO SET-UP
COMPLETED.
HAPPY VIEWING !

NO STATION.

PLEASE CONNECT

ANTENNA PLUG.

4

Aerial Connection

Aerial Cable

Connect the cable with a plug from a UHF (or VHF) aerial to the aerial socket on the cabinet back.

Aerial Socket

For all aerial circuit problems please consult
your local dealer.

Outdoor Aerial

Connecting Outdoor Aerial

Mounting Telescopic Aerial

Model CP14G1(C), CA14G1C, CP14SA1(C),
CP14SR1(C), CP20SR1(C)

Telescopic
Aerial

Telescopic
Aerial Feeder

Matching Box

Aerial Socket

Cabinet Back

Front Control

Each button listed in this section has the same function as it’s
corresponding button on the remote control.

Mains ON/OFF Button

Remote Control Detector

Stand-by and Power Indicator

Programme UP/DOWN

VOLUME

MENU

TV/AV Selector

Audio Input Jack

Video Input Jack

Model CP14G1(C), CA14G1C

Model CP14SA1(C), CP21SA1(C), CA21SA1C

Programme UP/DOWN

VOLUME

Remote Control Detector

Stand-by and Power Indicator

Mains ON/OFF button

TV/AV Selector

Video Input Jack

Audio Input Jack

MENU

ANT.75Ω

INPUT

OUTPUT

A

R
U
D
I
O

L

V
I
D
E
O

VIDEO

AUDIO

TV/AV

VIDEO

AUDIO

TV/AV

MENU

CH

MENU

-

+

CH

POWER

POWER

5

Programme UP/DOWN

VOLUME

Remote Control Detector

Stand-by and Power Indicator

Mains ON/OFF Button

Video Input Jack

Audio Input Jack

TV/AV Selector

Model CP14SR1(C)

Front Control

Programme UP/DOWN

VOLUME

Remote Control Detector

Stand-by and Power Indicator

Mains ON/OFF Button

Video Input Jack

Audio Input Jack

TV/AV Selector

Model CP20SR1(C)

Model CP21G1(C), CA21G1C

Programme UP/DOWN

VOLUME

Remote Control Detector

Stand-by and Power Indicator

Mains ON/OFF button

TV/AV Selector

Video Input Jack

Audio Input Jack

MENU

Each button listed in this section has the same function as it’s
corresponding button on the remote control.

VIDEO AUDIO

VIDEO AUDIO

GAME

-

GAME

+

CH

-

+

CH

POWER

POWER

VIDEO

AUDIO

TV/AV

MENU

CH

POWER

6

Remote Control Transmitter

-/- -

Power ON/OFF button

ALTERNATE button

VOLUME + button

TIMER button

MUTE button

CHANNEL SCAN button

SURROUND button

(This button is not used)

PICTURE MODE button

Programme UP button

RECALL/COLOUR SYSTEM button

MENU button

TV / AV Selector button

Programme Selector button

SWAP button

VOLUME - button

STEREO/MONO button

(This button is not used)

Programme DOWN button

BASS EXPANDER button

(This button is not used)

SOUND SYSTEM button

DIGIT button

SOUND MODE button

(This button is not used)

1. Open the battery cover.

2. Install two “AA” 1.5 volt batteries so that the “+” and “-” marks on the batteries match the “+” and

“ - ” marks inside the unit.

3. Close the battery cover.

Note: Replace the batteries when the TV set is showing the following symptoms:

Operation is unsteady or erratic, sometimes the TV set does not work with transmitter.
Discharged batteries may leak and damage the unit. The normal life of batteries should be from nine
to ten months.

Battery Installation of the Remote Control Transmitter

TV / AV

-/- -

SWAP

TIMER

CH

P

P

CH SCAN

A•B

BASS

MENU

SOUND

CH

S. SYS

PICTURE

SURROUND

JXPSC

7

General Operation

Important !

Be sure to set the Mains ON/OFF switch to the off
position, if the power failure occurs while viewing.

To switch on or off the TV ;

Press the Mains ON/OFF button.
The power of the TV is turned on or off complete­ly. If no picture appears but the Standby and Power
indicator illuminates, press the POWER ON/OFF
button of the remote control transmitter as the TV
set is in standby mode.

To set the TV to standby mode;

Press the POWER ON/OFF button.
During Standby mode the Standby and
Power indicator illuminates more brightly.

To turn on the TV from the standby mode,
press any of the following button.

● POWER ON/OFF button of the remote control

transmitter.

● Programme UP/DOWN of the remote control

transmitter or the TV set.

● 1 to 9, 0 button on the remote control

transmitter.

Power ON/OFF

This TV set incorporates the AUTO SHUT OFF
function. Even if the TV is left on after you have
gone to sleep, the TV set changes to the standby
mode within 10 minutes after all broadcasts have
ended.

OFF 0:10

Auto Shut Off Function

Press the Programme UP (CH▲ ) button

to select the next programme position.

Press the Programme DOWN (CH▼ )

button to select the previous programme
position.

Press the CHANNEL SCAN button to search for a
programme. The channel positions are automati­cally scanned, and the channel scanning will stop
at the position where it began. To stop at the posi­tion you want, press this button again.

Programme Up and Down

-/- -

-/- -

Channel Scanning

Direct Programme Selection

■ For direct access to select programmes

using (0~9) NUMERIC button.

■ To select programmes position more

than 9, press DIGIT button, and then
insert programme position number one
by one.
(Example: for programme position 15,
Press

“1”

button. Press

“5”

button

.

For

programme position

125

press the

Digit button twice. Press

“2”

button, press

“5”

button. For programme

255,

Press the
Digit button 3 times. Press “5” button. Press
“5” button.)

-/- -

Increase or decrease the sound volume level by
pressing the VOLUME (+ or -) buttons.

Volume Control

-/- -

To display the on screen indications, press
the RECALL/COLOUR SYSTEM button.

Screen display disappears after about 5 seconds.

29

AUTO

OFF 0:30
ON 3:30 6

Off Timer

On Timer

Programme
Position

BG

Sound
System

Colour
System

RECALL

Should you wish to mute the sound (e.g.
While talking on the telephone), press the
SOUND MUTE button. To switch the
sound back on, press the SOUND MUTE
button again or VOLUME (+ or -) button.

Sound Mute

CH

CH

CH SCAN

7

8

9

10

11

-/- -

SOUND

8

General Operation

Press the PICTURE MODE button to select
the following picture modes; “PERSONAL”,
”DYNAMIC”, ”NATURAL”, “ECO” and
“GAME”. Select picture modes to suit picture
type you are watching.

Quick Picture Controls

■ The OFF TIMER cancels when the TV set is

turned off or if a power failure occurs.

The OFF TIMER will switch off the TV automatical­ly after 30 minutes, 1 hour, 1 hour and 30 minutes,
or 2 hours.

1

Press the TIMER button.

2

Press the VOLUME ( + or - ) button to select

the time period.

OFF 0:00

■ Just one minute before switching off the TV,

“OFF 0:01” will be display on the screen.

■ To cancel the OFF TIMER, select “OFF 0:00”

by pressing the VOLUME (+ or - ) button.

OFF TIMER

When the ON TIMER is set. TV will automatically
be switched on to the selected programme posi­tion when the specified time has elapsed.

1

Press the TIMER button twice.

(ON TIMER setting mode)

ON 0:00 2

Programme position for when TV is
switched on by ON TIMER.

2

Press the VOLUME ( + or - ) button. The set

time will be increased or decreased by 10
minutes each time the button is pressed ; the
maximum time which can be set is 24 hours.

ON TIMER

■ If no operation is performed after the TV has

been switched on by the ON TIMER, such as
if you are not at home, the TV will be auto­matically switched off after approximately 2
hour.

■ If the TV is already switched on when the time

set for the ON TIMER has been reached, only
the programme position will be changed to the
set programme position.

■ Cancelling ON TIMER. To cancel the ON

TIMER, press the VOLUME ( + or - ) button to
set it to “ON 0:00” while the ON TIMER screen
is shown. Switching off the TV by pressing the
Mains ON/OFF button will also cancel the
ON TIMER settings.

3

Use Direct programme Selection to insert pro-

grammme position for when TV is switched on
by ON TIMER. (see page. 7)

Press the ALTERNATE button, and the pro-
gramme position will alternately select the
previous position and the present position.

ALTERNATE

Colour and Sound System

6

AUTO

6

PAL

6

NTSC4.43

6

NTSC

Normally, set the colour system to “AUTO”, if the
clear picture cannot be obtained even when the
broadcasting or AV signal is received, press the
RECALL/COLOUR SYSTEM button repeatedly
until the optimum image can be produced.
(Refer to Broadcast Transmission System List
indicated by the last of this page in a setup of
Colour System.)

Each time the RECALL/COLOUR SYSTEM but­ton is pressed, colour system changes as follows;

Setting of the Colour System

To set the sound system, make it during Semi­Auto Tuning or Manual Tuning mode.
When the sound is not clear or no sound is pro­duced on a programme number position, select
sound system repeatedly until the optimum sound
is obtained.
(Refer to Broadcast Transmission System List
indicated by the last of this page in a setup of
Sound System.)

Setting of the Sound System

P

P

PICTURE

9

Colour and Sound System

Page 1

The 2nd page is not displayed when there is no
TINT adjustment.

Page 2

Picture Adjustment Menu

To select sound system:

■ Press the SOUND SYSTEM button to select the

sound system directly. The sound system will
be memorized automatically.

or:

2) To enter a sound system selection into the
memory, select “MEMORY” and press the

VOLUME + or

-

button.

(Semi-Auto or Manual Tuning mode )

1) Select “SIF” with the Progamme UP or DOWN

button in the Semi-auto or Manual Tuning
mode.Then press the VOLUME ( + or -)
button to select a optimum sound system.

Broadcast Transmission System List

Area

Country

Sound

System

Colour

System

Middle

East

Asia

Oceania

PAL

B/G

Australia,
New Zealand, etc.

Union of Arab Emirates,
Kuwait, Oman, Qatar,
Yemen,

Bahrain,

etc.

Indonesia, Malaysia,
Singapore, Thailand,

etc.

PAL

B/G

China,

etc.

PAL

D/K

Hong kong

PAL

I

Saudi Arabia,
Iraq, Iran, Lebanon,etc.

B/G

SECAM

Russian Federation,etc.

D/K

SECAM

Myanmar, etc.

M

NTSC

BG

(5.5MHz)

DK

(6.5MHz)

I

(6.0MHz)

M

(4.5MHz)

Picture Adjustment

Picture Adjustment Item

COLOUR : Adjusts colour intensity.
BRIGHT : Adjusts picture brightness.
CONTRAST : Adjusts picture contrast.
TINT : Adjust colour tints. (Displayed only on

NTSC or NTSC4.43 system signal
reception.)

SHARPNESS : Adjusts picture detail.
WHITE TONE : Adjusts white balance.
FINE TUNING : Fine tuning in case of weak

broadcast signal or poor reception. Only
displayed in TV mode. Will not be displayed in
AV mode.

SEMI
START

2
AUTO

BG

OFF

--

MODE
SEARCH
POSITION
SYSTEM

SIF

SKIP
MEMORY

MODE
SEARCH
POSITION
SYSTEM
SIF
SKIP

MEMORY

SEMI
START

2

AUTO
BG
OFF

OK

COLOUR

BRIGHT
CONTRAST
TINT
SHARPNESS

SELECT ADJUST BACK

WHITE TONE

FINE TUNING

P

P

M

EXIT

SELECT ADJUST BACK

P
M

P

EXIT

10

Picture Adjustment

1

Press the MENU button for MAIN menu
display.

(MAIN MENU)

Basic Picture Adjustment Operation

2

When “PICTURE” is not selected, select

“PICTURE” with the Programme UP or

DOWN button.

3

Press the VOLUME + or-button to display
Picture Adjustment menu.

4

Select desired control by pressing the
Programme UP or DOWN button.

■ To return to Main menu, press the

ALTERNATE button.

■ To return to the normal TV mode, press the

MENU button. ( Or will automatically return to
the normal TV mode after 20 seconds.)

Approximately five seconds after you release the

VOLUME (+ /

-

) button, the screen display switch-

es from the adjustment screen to the normal TV
screen.

5

Press the VOLUME + or-button to alter
settings.

Tuning of the Channels

Up to 256 broadcast stations in your reception
area can be stored in the electronic memory.

There are three ways of tuning as follows;

1. Automatic Tuning (the basic way):

All receivable channels are automatically tuned
in and memorized in consecutive programme
position.

2. Semi-Auto Tuning:

Use to preset a receivable channel in any
desired programme position, e.g. the position
with the same number as the channel.

3. Manual Tuning:

Manually tune a channel if it cannot be
automatically tuned, such as when the signal is
poor.

2

Select “PRESET” by pressing the

Programme UP or DOWN button.

3

Press the VOLUME + or

-

button for
PRESET menu display. On entering PRESET
display, Automatic Tuning will be selected
initially.

1

Press the MENU button for MAIN menu

display.

Automatic Tuning

4

Select “SEARCH” by pressing the
Programme UP or DOWN button.

PICTURE

PRESET
LANGUAGE

PICTURE

PRESET
LANGUAGE

COLOUR

BRIGHT

CONTRAST
SHARPNESS
WHITE TONE
FINE TUNING

COLOUR

BRIGHT
CONTRAST
SHARPNESS
WHITE TONE
FINE TUNING

P

SELECT ADJUST BACK

M

P

EXIT

BRIGHT

P

ADJUST

PICTURE

PRESET

LANGUAGE

MODE

SEARCH
POSITION
SYSTEM
SIF
SKIP

MEMORY

SELECT ADJUST BACK

P

BACK

AUTO

START

6

AUTO
BG
OFF

--

M

P
M

EXIT

P

EXIT

MODE

SEARCH

POSITION
SYSTEM
SIF

AUTO

START

6
AUTO
BG

11

Tuning of the Channels

■ The Automatic Tuning operation can be

cancelled at any time by pressing the
Programme UP or DOWN button.

After all receivable channels have been found and
stored, the TV set automatically returns to pro­gramme position “1”.

-/- -

MENU

CH

CH

1

5

Press the VOLUME (+) button to start
channel tuning

.

1

Press the MENU button for MAIN menu
display.

2

Select “PRESET” by pressing the

Programme UP or DOWN button.

3

Press the VOLUME + or

-

button for
PRESET menu display. On entering
PRESET display, Automatic Tuning will
be selected initially.

4

Select “SEMI” or “MANUAL” by pressing the

VOLUME + or-button.

Semi-Auto Tuning and Manual Tuning

5

Select “SEARCH” by pressing the
Programme UP or DOWN button.

The VOLUME + button will move tuning toward
the higher frequencies, and the VOLUME -but­ton will move tuning toward the lower frequencies.

8

Press the MENU button to return to normal
TV display.

6

Once desired channel is located, select
“MEMORY” by pressing the Programme UP
or DOWN button.

7

Press the VOLUME + or-button to enterthe
desired channel into Programme Position 6.

To pre-set other Programme Positions, repeat
steps 5-8.

2

Enter to SEMI-AUTO or MANUAL tuning
mode. (Refer to page 11.)

3

Select “POSITION” with the Programme UP
or DOWN button.

This function can be utilized after Automatic
Tuning.

For example, to copy a TV channel on programme
position “2” onto programme position “6”;

1

Select programme position “2” .

2

4

Select position “6” with the VOLUME + or

-

button.

Channel Copy

5

Select “MEMORY” by pressing the

Progamme UP or DOWN button.

7

Press the MENU button to return to normal
TV display.

6

Press the VOLUME + or

-

button to

memorize.

Semi-Auto Tuning:

Press and release the VOLUME + or - button
to search for required TV station. Once a station
is located, tuning will automatically stop.
Continue till desired channel is located.

Manual Tuning :

Press and hold the VOLUME + or

-

button

to search for required TV station.

PICTURE

PRESET

LANGUAGE

SKIP

MEMORY

SELECT ADJUST BACK

OFF

OK

P
M

P

EXIT

MODE

SEARCH
POSITION
SYSTEM

MODE

SEARCH

POSITION
SYSTEM

MODE

SEARCH

POSITION

SYSTEM

SEMI

START

6

AUTO

SEMI

6

AUTO

MANUAL

6

AUTO

MODE
SEARCH

POSITION

SYSTEM

SEMI
START

6

AUTO

12

Tuning of the Channels

Channel Swapping

Use this channel swapping feature to swap the
channels between two stored programme position.
This feature is particularly useful after automatic
tuning.

1

Select programme position “6”.

2

Press the SWAP button.

For example, to swap the channel between pro­gramme position “6” and programme position
“12”.

6

12

6

SWAP 6 AND

-

3

Press the DIGIT button, “ 1 “ button and then
“ 2 ” button on the remote control to enter
programme number 12. (For example, to
enter programme number “ 3 “, press “ 3 ”
button only. )

SWAP 6 AND 12

4

Press the SWAP button.

12

SWAPPING

The two TV channels will now have changed
places.

6

12

6

Press the MENU button to return to normal
TV display.

4

Select “SKIP” by pressing the Progamme UP
or DOWN button, then press the
VOLUME + or-button to set SKIP to ON.
To cancel Skip Channel function, set to OFF.

5

Select “MEMORY” by pressing the

Progamme UP or DOWN button, then press
the VOLUME + or

-

button for memory.

Any number of channels maybe set as Skip
Channels.

1

Enter to SEMI-AUTO or MANUAL tuning
mode. (Refer to page 11.)

2

Select “POSITION” with the Progamme UP
or DOWN button.

When there is a position you do not use, Position
4 for example, by setting the SKIP Channel func­tion it is possible to jump over this position, when
you are selecting a channel using the Progamme

UP/DOWN or CHANNEL SCAN button.

3

4

5

Skip

For example, to set programme position “4” as
Skip channel ;

3

Press remote control “4” button to select
Programme Position 4. Use the DIGIT button
and Progamme Selector (Number buttons)
to enter Programme Number. Do not use the
VOLUME + or -button to enter programme
position in this settings.

Skip Channel Set and Cancel

MODE
SEARCH

POSITION

SYSTEM
SIF
SKIP
MEMORY

MODE
SEARCH
POSITION
SYSTEM
SIF

SKIP

MEMORY

MODE
SEARCH
POSITION
SYSTEM
SIF
SKIP

MEMORY

SEMI
START

4

AUTO
BG
OFF

--

SEMI
START

4

AUTO
BG

ON

--

SEMI
START

4

AUTO
BG
ON

OK

13

Setting of the Private Position

For example, to set the programme position
“15” as the private position.

1

Select programme position “15”.

15

15

The programme number “15” will shift to centre of
the screen.

15

AUTO

The picture will disappear, and “ 15” will be
disply on the screen.

The private position setting is now completed.

3

Press the MENU button.

Private position is used to restrict of pro­gramme positions that you do not want others
to watch. Any position can be set as the
Private position.

BG

How to Set the Private Position

BG

15

15

1

Select private position (In this case position
“15”).

2

Press and hold the RECALL/COLOUR
SYSTEM button for more than 2 seconds.

3

Press the RECALL/COLOUR SYSTEM
button for watching a TV programme.

Note: The position “15” is still in the private position.

15

AUTO

BG

To View a Programme on Private Position

The private position is now cancelled.

1

Select private position (position “15”).

2

Press and hold the RECALL/COLOUR
SYSTEM button for more than 2 seconds.

3

Press the MENU button.

15

AUTO

BG

Cancelling of the Private Position

15

15

2

Press and hold the RECALL/COLOUR
SYSTEM button for more than 2 seconds.

1

Press the MENU button for MAIN menu display.

2

Select “LANGUAGE “ by pressing the

Programme UP or DOWN button.

3

Press the VOLUME + or

-

button for

Language menu display.

Setting of the OSD (On Screen Display) Language

4

Press the MENU button to return to normal
TV display.

Select “ENGLISH”, “ ”, “VIETNAMESE”,
“ ”, “FRANÇAIS”, “BAHASA INDONE-

SIA” by pressing the

Progamme

UP or DOWN

button. To return to the normal TV mode, press
the MENU button.

15

AUTO

PICTURE
PRESET

LANGUAGE

PICTURE
PRESET

LANGUAGE

ENGLISH

VIETNAMESE

y

PCC
FRANCAIS
BAHASA INDONESIA

y

P

C

C

NN

NN

14

Connecting other Equipment

Connect the video and audio outputs of a VCR, video disc player, etc. to the input jacks of this TV set .
Tapes and discs can be played back.

■ To watch video input picture, select AV position by pressing the TV/AV Selector

AV

VCR for playback

PLAYBACK

To video and audio outputs

Model CA14G1C, CP14SA1(C)

, CP14SR1(C), CP20SR1(C), CP21SA1(C), CA21G1C, CA21SA1C only.

VCR for playback

T

o video and audio outputs

PLAYBACK

Model CP14G1(C), CP21G1(C).

Connecting to the Rear AV Input Jacks

For example:

aIt is convenient to use the AV input jack on the front panel for
equipment that is often connected and disconnected.

Video Camera,

Game Station etc.

To video and
audio outputs

PLAYBACK

Note:

Do not connect external equipment to both rear and front AV input jacks to avoid signal mix and
distorted picture.

Connecting to the Front AV Input Jacks

■ You can select a TV programme while watching a playback from a VCR

● To select programme position “9” while watching a playback from external VCR, press “9” button of

the remote control. The TV set returns to the TV mode and programme “9” will be selected.

● To select the programme position “26”, press Digit (--/-) button, “2” then “6” button. Then

TV set returns to the TV mode and programme position “26” will be selected.

Note: Pressing either of the PROGRAMME UP or DOWN buttons of the remote control or the TV will

return the TV to the TV mode.

INPUT

OUTPUT

A
U
D
I
O

V
I
D
E

O

INPUT

OUTPUT

A
U
D

I

O

V

I
D
E
O

R

L

VIDEO

AUDIO

15

Connecting other Equipment

Colour system setting for AV position is automatically stored in the memory.

Each time the RECALL/COLOUR SYSTEM button is pressed, colour system is changed as follows;

AV

AUTO

AV

PAL

AV

NTSC4.43

AV

NTSC

Depending on the type of video tape or connected AV equipment being used, it may be necessary to
select colour system. In this case, press the RECALL/COLOUR SYSTEM button and select a suitable
colour system.

Selecting the Colour System in AV Mode

■ To dub video from the AV terminal input, select AV

position by pressing the TV/AV Selector.

The picture signal being displayed on the TV screen is output through the Monitor Output Jacks. Use
these terminals to record TV broadcasts and for video dubbing from AV input terminals.

■ To record TV programme, select TV mode

by pressing the TV/AV Selector and
record the desired programme.

TV mode

AV

15

Recording TV broadcasts or tape dubbing

VCR for recording

To video and audio inputs

Note: Model CA14G1C, CP14SA1

(C), CP14SR1(C), CP20SR1(C), CP21SA1(C), CA21G1C, CA21SA1C

only.

Connecting to the Monitor Output Jacks

Aerial Socket

The AV apparatus can also be connected to the aerial socket of your TV receiver.

Presetting to watch the video input

1. Playback the VCR .

2. Tune a VCR playback in programme position that you want. (See Semi-Auto Tuning and Manual Tuning

on pages 11.)

For further details concerning this connection and adjustment, refer to the operating instructions
for the AV equipment.

VCR for playback

PLAYBACK

AV Connection to the Aerial Socket

OUTPUT

A
U
D

I

O

V

I
D
E
O

INPUT

ANT.75Ω

16

Care and Cleaning

The surface of the cabinet can be damaged if not properly maintained. Many common household aerosol
sprays, cleaning agents, solvents and polishes will cause permanent damage to the fine surface.

1. Unplug the power cord before cleaning the Television.

2. Clean the screen with a soft cloth dampened with glass cleaner or warm water.

3. Clean the cabinet with a soft cloth dampened with a mild household detergent and warm water. Dry

thoroughly.

Note: NEVER spray liquids on the screen because they can run down and drip onto the chassis. This

may cause component failure not covered under Warranty.

17

Specifications

Power Source AC110-240 Volts, 50/60Hz

Colour System PAL/PAL-60Hz/NTSC/NTSC4.43

Sound System B/G, I, D/KK’, M/M

Channel Coverage

VHF: E2-E12, R1-R12, K1-K9, J1-J12, A2-A13 // 0-11, 5A(AUS), 1-11(NZ)
UHF: 21-69, A14-A69, J13-J62 // 28-69(AUS)
CATV: S1

-

S41, X, Y, Z, Z+1, Z+2

Aerial input impedance 75 Ω

Audio output (RMS)

Model CP14SA1(C), CP20SR1(C), CP21SA1(C): 2W
Model CP14G1(C), CA14G1C, CP14SR1(C), CP21G1(C): 3W
Model CA21SA1C, CA21G1C: 5W

Speakers

Model CP14G1(C), CA14G1C, CP14SA1(C), CP21SA1(C), CA21SA1C: Ø 8 cm x 1 pc.
Model CP14SR1(C), CP20SR1(C): 5 cm x 9 cm x 1 pc
Model CP21G1(C), CA21G1C: Ø 8 cm x 2 pcs.

Ext. terminals

Model CA14G1C, CP14SA1(C), CP14SR1(C), CP20SR1(C), CP21SA1(C), CA21G1C, CA21SA1C

Video Inputs: Phone Jack x 2 (1.0Vp-p, impedance 75)

Audio inputs: Phone Jack x 2 (436mVrms, impedance more than 40KΩ)
Video monitor outputs: Phone Jack x 1 (1.0Vp-p, impedance 75 Ω)
Audio monitor outputs: Phone Jack x 1 (436mVrms, impedance less than 600Ω)

Model CP14G1(C), CP21G1(C)

Video inputs: Phone Jack x 2 (1.0Vp-p, impedance 75 Ω)

Audio inputs: Phone Jack x 2 (436mVrms, impedance more than 40KΩ)

Dimensions

Model CP14G1(C), CA14G1C: 371 (W) x 349 (H) x 384 (D) mm
Model CP14SA1(C): 365 (W) x 362 (H) x 383 (D) mm
Model CP14SR1(C): 363 (W) x 346 (H) x 366 (D) mm
Model CP20SR1(C): 496 (W) x 446 (H) x 470 (D) mm
Model CP21G1(C), CA21G1C: 502 (W) x 462 (H) x 493 (D) mm
Model CP21SA1(C), CA21SA1C: 501 (W) x 476 (H) x 492 (D) mm

Weight

Model CP14G1(C), CA14G1C, CP14SA1(C): approx. 8.7 Kg
Model CP14SR1(C): approx. 8.6 Kg
Model CP20SR1(C): approx. 17.2 Kg
Model CP21G1(C), CA21G1C: approx. 19.5 Kg
Model CP21SA1(C), CA21SA1C: approx. 20.5 Kg

Specifications subject to change without notice.

18

Helpful Hints - Problems/Solutions

Before requesting service check the following chart.

“GHOSTS”

Reflections of signals from mountains or high buildings will cause multiple images, called “Ghosts”.
These abnormal conditions can be reduced to minimum by repositioning aerial or by installing new one
suited for your area.

“INTERFERENCE”

Interference may be caused by electrical appliances, car ignition systems, etc. This should normally be
a temporary condition, but should this interference persist, contact your dealer.

The following faults are not caused by the receiver:

● Check aerial connection on back of TV set.

● Check aerial for broken wires. ● Re-orient aerial.

Problem: Check these Conditions / Try these solutions:

● Check if TV is plugged in.

● Try a different channel, if OK, probably station trouble.

No picture,
no sound

● Adjust Brightness or Contrast control.

● Adjust Fine Tuning. (See page 9.) ● Check aerial connection.

Poor picture,
sound OK

No colour,
Picture OK

● Adjust Colour or Tint control. ● Adjust Fine Tuning. (See page 9.)

●

Check aerial connection.● Is the programme in colour ? Try a different channel.

● Select other colour system. (See Setting of the Colour System on page 8.)

Weak picture

No sound or poor
sound.

●

Sound Mute may be on. Press the

SOUND MUTE

button on the remote control.

● Adjust Volume. ●

May be station trouble. Try a different channel.

● Select other sound system. (See Setting of the Sound System on page 8-9.)

Remote Control
will not work.

● Check batteries. Replace batteries.

● Check if TV set is plugged in. Aim remote control towards front of TV.

Cannot select or
scan some channels.

● Channel may be removed from memory. Add channel to memory manually.

(See “Skip Channel Set and Cancel” on page 12.)

●Check aerial connection.

● This is a normal condition during warm-up and cool down of the plastic

cabinet parts.

Blue screen with AV
is displayed

● Check AV connection. Press the TV/AV Selection button.

● Check external equipment. Switch on external equipment.

● Check to see if channel is set as the Private Position. See “Setting of the

Private Position” on page 13.

Black screen with
and programme
position displayed.

Cabinet makes
popping sound.

19

Memo

SANYO ELECTRIC Co., Ltd.

Part No. 1AA6P1P4898-- C5SWC (AC6-A)