Sanyo AVM2425 User Manual
AS
Color TV
Owner’s Manual
Model No. :
AVM2425
POSITIONING THE TV
Do not position the TV in a confined area. Allow space for
normal air circulation around electronic parts.
CHILD SAFETY
Sanyo is committed to making home entertainment safe
and enjoyable. Always use an appropriate table or stand
when positioning your TV. Use appropriate brackets,
braces, or straps to anchor your furniture in place. But
NEVER screw anything directly to the television.
Do not place televisions on dressers, shelves, desks,
carts, etc. where curious or excited children could pull,
push, or otherwise cause the unit to fall and cause
personal injury.
Never place toys or other items on top of the TV that
could pique children’s curiosity causing them to climb
about the furniture.
Always use stands that are designed to support the size
and combined weight of your television and other
electronic devices.
IMPORTANT NOTE:
Spent or discharged batteries must be recycled or
disposed of properly in
compliance with all applicable laws. For detailed
information, contact your
local County Solid Waste
Authority.
BASIC SETUP AND CONNECTIONS
1.
Install batteries in remote control (2 AAA, not included).
2.
Connect signal. (See illustration below.)
3.
Plug in AC power cord.
4.
Press the POWER key to turn on TV.
5.
Follow on-screen instructions.
PICTURE TUBE SIZE
(Measured Diagonally) . . . . . . 24-inches Screen
PICTURE RESOLUTION
Antenna Input . . . . . . . . . . . . . . . . . . 260 Lines
Video Input . . . . . . . . . . . . . . . . . . . . . . . 260 Lines
ANTENNA INPUT . . . . . . . UHF/VHF/CATV 75Ω
POWER REQUIREMENT . . . . . . . . 120VAC 60Hz
POWER . . . . . . . . . . . . . . . . . . . . . . . . 78 watts
HORIZONTAL DIM. (Width) . . . 24.4 in. (619mm)
VERTICAL DIM. (Height) . . . . 22.4 in. (570mm)
DEPTH DIM. (Thickness) . . . . 21.2 in. (538mm)
WEIGHT (Approx.) . . . . . . . . 60.6 lbs. (27.5 Kg.)
SOUND (1 Speaker) . . . . . . . . . . . . . Size: 8 cm
AMPLIFIER . . . . . . . . . . . . . Built-in with 1W/ch
AUDIO/VIDEO INPUT
JACKS (FRONT) . . . . . . . . . . . Video/Audio Input
CAUTION: FCC Regulations state that unauthorized
changes or modifications to this equipment may void the user’s authority to
operate it.
Care and Cleaning
1. Unplug the power cord
before cleaning the
television.
2. Clean the screen and cabinet
with a soft dry cloth.
Note:
Never spray liquids on the screen because it
can run down and drip onto the
chassis. This may cause component failure
not covered under Warranty.
SPECIFICATIONS
Printed in U.S.A. SMC, August 2006
Part No.:
1JC6P1P0240– –
Welcome to the World of Sanyo
Thank you for purchasing a Sanyo Color Television. You made an excellent choice for Performance,
Styling, Reliability, and Value. This television is designed with easy-to-use on-screen set-up instructions and
operating features.
If you need assistance visit our Web site at
www.sanyoctv.com or call toll free 1-800-877-5032.
Positioning the appliance
1. Do not place your appliance on an unstable cart, stand, shelf or
table. Serious injury to an individual, and damage to the appliance,
may result if it should fall. Your salesperson can
recommend approved carts and stands or shelf
and wall mounting instructions. An appliance and
cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
2. Slots and openings in the cabinet and in the back or bottom are provided for ventilation. To ensure reliable operation of the appliance and
to protect it from overheating, these openings must not be blocked or
covered. The openings should never be covered with a cloth or other
material, and the bottom openings should not be blocked by placing
the unit on a bed, sofa, rug, or other similar surface. This appliance
should never be placed near or over a radiator or heat register. This
appliance should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.
3. Do not expose the appliance to rain or use near water . . . for example,
near a bathtub, swimming pool, kitchen sink, in a wet basement, etc.
Hooking Up Outdoor Antenna
LIGHTNING PROTECTION FOR YOUR ANTENNA AND SET AS PER
NATIONAL ELECTRICAL CODE INSTRUCTIONS.
EXAMPLE OF ANTENNA GROUNDING ACCORDING TO
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
4. If an outside antenna is connected to the receiver, be sure the
antenna system is grounded so as to provide some protection
against voltage surges and built up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information
with respect to proper grounding of the mast and supporting structure, grounding of the lead in wire to an antenna discharge unit,
size of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for the
grounding electrode.
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where
it can fall into such power lines or circuits. When installing an outside
antenna system extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
Plug in the power cord
5. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your product dealer or local
power company. This product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of this polarized plug. Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.
6. Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
Cleaning
7. Before cleaning, unplug the unit from the wall outlet. Do not apply liquid
cleaners or aerosol cleaners directly to the unit. Use a dry cloth for
cleaning.
Service & Repair
8. Unplug the appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions:
A. If the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the appliance.
C. If the appliance has been exposed to rain or water.
D. If the appliance has been dropped or the cabinet has been
damaged.
E. If the appliance exhibits a distinct change in performance.
F. If the appliance does not operate normally by following the
operating instructions, adjust only those controls that are cov-
ered in the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the appliance to
normal operation.
9. Upon completion of any service or repair, request the service technician’s assurance that only Factory Authorized Replacement Parts
that have the same characteristics as the original parts were used,
and that routine safety checks have been performed to determine
that the appliance is in safe operating condition. Unauthorized substitutions may result in fire, electrical shock, or other hazards.
10. Never add accessories that have not been specifically designed for use
with this appliance as they may cause hazards.
11. For added protection during a lightning storm, or when the set is left
unattended and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna. This will prevent damage to
the set due to lightning or power line surges.
12. Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS
UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THIS UNIT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE ADHERE TO ALL WARNINGS ON THE PRODUCT AND IN THE OPERATING INSTRUCTIONS. BEFORE OPERATING THE PRODUCT, PLEASE READ ALL OF THE SAFETY AND OPERATING INSTRUCTIONS. RETAIN THIS LITERATURE FOR REFERENCE.
Follow all instructions...
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article
820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system
of the building, as close to the point of cable entry as practical.”
TV
Cable Service RF AntennaSatellite Receiver
VCR
CATV FRANCHISE NOTE:
Cable companies, like public
utilities, are franchised by
local government authorities.
To receive cable programs,
even with equipment which is
capable of receiving cable
channels, the consumer must
subscribe to the cable company’s service.
Note: If you do not have a
VCR, connect signal directly to TV 75
ohm terminal.
This symbol on the nameplate means the product is Listed by Underwriters’ Laboratories
Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of
fire, casualty, and electrical hazards.
ENGLISH
ONE-YEAR LIMITED WARRANTY
THIS LIMITED WARRANTY IS VALID ONLY ON SANYO TELEVISIONS PURCHASED AND USED IN THE UNITED STATES OF AMERICA, CANADA, AND
PUERTO RICO, EXCLUDING THE UNITED STATES’ OTHER TERRITORIES
AND PROTECTORATES. THIS LIMITED WARRANTY APPLIES ONLY TO THE
ORIGINAL PURCHASER, AND DOES NOT APPLY TO PRODUCTS USED FOR
INDUSTRIAL OR COMMERCIAL PURPOSES.
FOR ONE YEAR from the date of purchase, Sanyo Manufacturing Corporation
will replace any defective TV.
To insure proper warranty exchange, keep the original sales receipt for
evidence of purchase. Return the defective TV to the retailer along with the
receipt and the included accessories, such as the remote control. The
defective TV will be exchanged for the same model, or a replacement
model of equal value, if necessary. Replacement model will be contingent
on availability and at the sole discretion of Sanyo Manufacturing
Corporation.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
OBLIGATIONS
For one year from the date of purchase, Sanyo Manufacturing Corporation warrants this product to be free from defects in material and workmanship under normal use and conditions.
Should replacement be necessary under this warranty for any reason due to manufacturing
defect or malfunction during the first year from date of original purchase, Sanyo Manufacturing
Corporation will provide a new TV via exchange at the retailer.
For customer assistance, whether during or out of the warranty
period, call toll free 1-800-877-5032.
Weekdays 7:30 AM – 7:00 PM Central Time
Saturday 7:30 AM – 4:00 PM Central Time
This warranty expresses specific contractual rights; retail purchasers may have additional
statutory rights which vary from state to state.
(EFFECTIVE: August 1, 2002)
For your protection in the event of theft or loss of this product, please fill in the
information requested below and KEEP IN A SAFE PLACE FOR YOUR OWN
PERSONAL RECORDS.
Model No.__________________ Date of Purchase __________________
Serial No.__________________ Purchase Price ____________________
Where Purchased__________________
(Located on back of unit)
AS
Sanyo Manufacturing Corp.
3333 Sanyo Road, Forrest City, AR 72335
WARRANTY
AS
A
S
V
I
D
E
O
I
N
L
-
A
U
D
I
O
-
R
CATV IN
CH3
CH4
OUT TO TV S-VIDEO
L- -RAUDIOVIDEO
L- -RAUDIOVIDEO
IN
FROM ANT.
OUT
OUT TO TV
IN FROM
SAT.
UHF / VHF / CATV
75Ω
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
EQUIPMENT
NEC
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
- NATIONAL ELECTRICAL CODE
VI DEO IN A UDI O I N
Camcorder
Press INPUT after
making connections.
Video Game
Notes:
– Switch off TV and external equipment before connecting cables. (Cables are not supplied
with TV.)
– One audio plug will not be used when connecting a stereo device. Just leave the red audio
plug disconnected from both units.
– Only one device at a time can be connected to these jacks.
USING FRONT A/V (AV1) JACKS
1. Connect a video game, camcorder,
or other external equipment to the
TV as shown.
Input Key—Press to select the program
source to watch: TV signal or signal from
DVD Player or other equipment you have
connected to the A/V jacks.
Menu Key—Use this key with the
and – + keys to navigate and adjust features of the on-screen menu system.
Channel Scanning (CH ) and
Volume (VOL – +) Keys—Press to scan
through the channels in memory and to
adjust the volume.
Mute Key—Press once to suppress the
volume. Press again to restore volume
to previous level.
Note:
When using the audio out jacks
this key will not mute the sound.
Caption Key—Captioning is text information transmitted along with the picture
and sound so it can be displayed on the
TV screen.
1. Press CAPTION.
2. Press 0 (zero) to select options: OFF,
C1, C2, T1, T2, or QUIKCAP.
Notes:
Quikcap switches captions on
and off with the Mute function.
If a black box appears on the
screen, press the RESET key
twice.
V-Guide Key—(See V-Guide Operation.)
Note:
This feature is designed to comply with the United States of America’s
FCC V-Chip regulations. Therefore, it
may not function with broadcasts that
originate in other countries.
Use this feature to supervise the television viewing of young children. This TV
can be set to automatically block programs with content you deem as inappropriate for your children to view.
Reset Key—Press this key twice to
restore factory settings. The TV will automatically start Channel Search and clear
all customized settings. These features
will automatically reset:
Picture Adjustments: Color, Tint,
Contrast, Bright, and Sharpness
Channel Memory
Caption to OFF
V-Guide to OFF
Language to English
Sleep Timer
Game/ Video mode to TV
If desired, personal settings can be
made again using the menu options.
Power Key—Press to turn TV ON or
OFF.
Recall Key—Press to switch between
the last two channels you selected.
Display Key—Press once to display the
channel number. Press twice to display
the channel number continuously. Press
again to remove the channel number.
Number Keys—Press two keys to
select a channel. Example: Press 0 then
6 to select channel 6. For cable channels 100 through 125
, press and hold
the 1 key until C1– – appears. Then
press the other two numbers.
Sleep Key—Press this key then press
the “0” key to set the Sleep Timer. The
desired time can be set from 30 minutes up to 3 hours in 30-minute increments. Sleep Timer will switch off the
TV automatically.
Note:
The Sleep Timer cancels when
the TV is turned off or if a power
failure occurs.
11
12
11
12
REMOTE CONTROL OPERATION
Point towards TV
ON-SCREEN MENU OPERATION
1. Press MENU.
2. Use the keys to highlight a feature.
3. Use the – + keys to choose an option.
4. Press MENU to exit.
Items with submenus requires additional steps.
Automatic Picture Adjustment
1.
Highlight Auto for normal viewing or Game for video game settings.
Note: When you choose
Game
, the picture will automatically adjust to ideal game
settings.
Manual Picture Adjustment
1. Highlight Manual.
2. Press MENU.
3. Use the keys to choose Color, Tint, Contrast, Bright, or Sharpness.
4. Use the – + keys to make adjustment.
Resetting the CABLE–VHF/UHF mode or Channel Search
These changes are required only if additional channels become available, such as
switching from Antenna to Cable.
1. Highlight CH. Search and press the + key.
Adding or Deleting Channels
1. Press MENU key.
2. Highlight CH. Scan Memory.
3. Press the + key.
4. Enter the channel number you want to add or delete.
5. Press the + key to change the present setting. Example: Added will change to
Deleted. This takes about three seconds. During that time, the word “Added” or
“Deleted” will become yellow.
6. Use the 0 ~ 9 or keys to choose other channels to delete or add, or press
the MENU key to exit.
V-GUIDE OPERATION
Setting MPAA Movie Rating
1. Press V-GUIDE.
2. Press the + key to switch V-Guide ON.
3. Highlight MPAA Rating, if necessary.
4. Press the + key to select a rating option.
5. Press the MENU key to change rating (B↔U).
Setting TV Ratings
6.
Highlight TV Ratings.
7. Press the + key to select rating option.
8. Press the MENU key to change rating (B↔U).
Setting Content-Based Rating
9. Select Contents.
10. Press the MENU key to display the Contents
options: D, L, S, V, or FV. (D-Suggestive Dialog,
L-Adult Language, S-Sexual Situation, V-Violence,
FV-Fantasy Violence.)
11. Highlight desired option: D, L, S, V, or FV.
12. Use the – + keys to select rating.
13. Press the MENU key to change rating (B↔U).
14. Use the keys to highlight another content
rating. Repeat steps 11 through 13 to block or
unblock rating.
15. Press the V-GUIDE key to exit.
Turning Off the V-Guide
1. Press the V-GUIDE key.
2. Use the – + keys to select OFF.
Auto Manual Game
Cable VHF/UHF
CH. Search +
CH. Scan Memory +
ENGL FRAN ESPA
Use
–+, keys
>
>
>>>
>
OFFOOOONNNN
MPAA Ratings :
XU
TV Ratings :
Use – +, keys
MENU key to Block
>
>
OFFOOOONNNN
MPAA Ratings :
TV Ratings : Contents
Press MENU key
>
>
Deleted C34
UUUUsssseeee ,,,, 0000~~~~9999,,,, ++++ kkkkeeeeyyyyss
ss
OFFOOOONNNN
MPAA Ratings :
TV Ratings : TVMA U
Use – +, keys
MENU key to Block
>
>
D: TV14 B
L:
S:
V:
FV :
Use – +, keys
MENU key to Block
What you will need
:
AV Cable - 1
POWER
MENU
VOL
MUTE
1
1
4
4
789
789
CAPTION
V-GUIDE
CH
RESETINPUT
RECALL
VOL
DISPLAY
3
2
3
2
6
5
6
5
SLEEP
0
0
VIDEO IN AUDIO IN
POWER
RESETINPUT
CH
RECALL
VOL
DISPLAY
MENU
VOL
MUTE
Loading...