Service Informationen 2000
Mechanism Manual
This manual explain how to remove and assemble by 10 illustration as follows.
May help the service manual of DC-C10, C30, C50, C70 Series.
Note: A name in this explanation uses a name mentioned in mechanism number list.
Operate it in number order.
Objet Models as follows
DC-AWM-2200/US (129 554 00) DC-C10/US (129 554 01) DC-C10/CA (129 554 02)
DC-C10/PA (129 554 03) DC-C10/XE (129 554 05) DC-C10/AU (129 554 06)
DC-AWM-2200/MX (129 554 07) DCS-C20/US (129 554 08) DC-C10/KR (129 554 09)
DCS-C40/US (129 556 00) DC-C30/CA (129 556 01) DC-C30/UK (129 556 03)
DC-C30/XE (129 556 04) DC-C30/AU (129 556 05) DC-C30/PA (129 556 06)
DC-C40/CA (129 556 07) DC-C30/KR (129 556 08) DCS-C60/US (129 558 01)
DC-C50/CA (129 558 01) DC-C50/UK (129 558 04) DC-C50/XE (129 558 05)
DC-C50/PA (129 558 06) DCS-C100/US (129 560 00) DC-C70/CA (129 560 01)
DC-C70/UK (129 560 03) DC-C70/XE (129 560 04) DC-C70/AU (129 560 05)
DC-C70/PA (129 560 06) DC-007C/UK (129 569 00) DC-007C/SS (129 569 02)
DC-007C/AU (129 569 03) DC-007CT/CA (129 569 04)
A. Remove the COVER2
Remove the 4 screws and remove the CM23 COVER2.
2
1
1
1
1
3 CD MECHANISM INSTRUCTION
3CD Changer Mechanism
SESE Sanyo Electric Service Europe
FILE Nr.
Seite 1 von 6
Service Informationen 2000
B. Disassembly the DRAWER 2 (Step 1)
1. Slide CM35 SLIDER 1 back and forth(Fig.1).
Drawer's lock is released.
2. Pull CM02 DRAWER 2 half way out.
C.
Disassembly the DRAWER 2 (Step 2)
1. Push the DRAWER up a little, and push the other side of DRAWER to remove (Fig.2).
PULL
SLIDER 1
CM35
1
3
PUSH
2
OPEN
CLOSE
3
1
3
1
1
3
2
PUSH
HOOKHOOK
HOOK
HOOK
2
Fig.1
Fig.2
3 CD MECHANISM INSTRUCTION
SESE Sanyo Electric Service Europe
FILE Nr.
Seite 2 von 6
Service Informationen 2000
D. Position confirmation
1. Rotate CM18 BEVEL GEAR 4 to check CM12/CM13 (or CM14) CARRIAGE movement and position.
If it is good, two carriages are the same position at the end (front position) (Fig.3).
E. If CARRIAGE was slid out of the drawer,
1. Turn CM18 BEVEL GEAR 4 to rotate CM19 CARRIAGE LIFT until it stops once (Fig.4).
2. Place CM13 CARRIAGE No.2 as shown in the illustration (Fig.5).
3. Turn CM18 BEVEL GEAR 4 to slide the carriage into its position.
Keep rotate until it sopts.
1
2
2
1
NO.1 CARRIAGE
CM12
NO.2 CARRIAGE
CM13
BEVEL GEAR 4
CM18
1
2
3
4
1st. TOOTH
AB
C
D
NO.2 CARRIAGE
CM13
Fig.3
Fig.5
CARRIAGE LI
F
CM19
NO.1 CARRIAGE
CM12
NO.2 CARRIAGE
CM13
BEVEL GEAR 4
CM18
Fig.4
3 CD MECHANISM INSTRUCTION
SESE Sanyo Electric Service Europe
FILE Nr.
Seite 3 von 6
Service Informationen 2000
4. Push CM13 CARRIAGE No.2 up with your fingers (Fig.6).
5. Place CM12 CARRIAGE No.1 as shown in the illustration (Fig.7).
6. Turn CM18 BEVEL GEAR 4 to slide the carriage into its position.
2
1
BEVEL GEAR
CM18
NO.2 CARRIAGE
CM13
BEVEL GEAR 4
CM18
2
3
4
1st. TOOTH
NO.1 CARRIAGE
CM12
NO.1 CARRIAGE
CM12
NO.2 CARRIAGE
CM13
NO.2 CARRIAGE
CM13
Fig.6
Fig.7
3 CD MECHANISM INSTRUCTION
SESE Sanyo Electric Service Europe
FILE Nr.
Seite 4 von 6
Service Informationen 2000
F. CARRIAGE Playback positon
If the CARRIAGE is wrong position,
1. Slide CM35 SLIDER 1 to lift CM32 CLAMPER up (Fig.8).
2. Place CM14 CARRIAGE No.3 on CM43 CARRIAGE LIFT UP (Fig.9).
3. Slide CM35 SLIDER 1 back to its original position.
CLAMPER
CM32
PULL
SLIDER 1
CM35
2
1
OPEN
CLOSE
3
PUSH
SLIDER 1
CM35
2
OPEN
CLOSE
CLAMPER
CM32
LIFTER
CM43
LIFTER
CM43
1
3
NO.3 CARRIAGE
CM14
Fig.8
Fig.9
3 CD MECHANISM INSTRUCTION
SESE Sanyo Electric Service Europe
FILE Nr.
Seite 5 von 6
Service Informationen 2000
G.Mechanism Assembly (Fig.10)
1. Make sure CM18 BEVEL GEAR 4 is in the place.
2. Make sure CM39 GEAR IDLER A2 is in the place.
3. Match CM27 BEVEL GEAR 1 as shown in the illustration (Fig.11).
4. Assemble the right side of CM02 DRAWER 2.
5. Insert Section A and slid it toward front as shown int the illustration (Fig.12).
6. Push it into CM01 ASSY CHASSIS.
7. Push CM02 DRAWER 2 back into the position.
8. Assemble CM23 COVER 2.
Fig,10
Fig.12
Fig.11
3
ARM STOPPER B
CM38
2
3
4
1
3
A
A
B
GEAR IDLER A2
CM39
B
CHASSIS
CM01
DRAWER 2
CM2
BEVEL GEAR 4
CM18
BEVEL GEAR 1
CM27
3 CD MECHANISM INSTRUCTION
SESE Sanyo Electric Service Europe
FILE Nr.
Seite 6 von 6
Loading...