Sanwa Electronic Instrument Co RM Y822A User Manual

4-097-333-21

© 2003 Sony Electronics.
Reproduction in whole or in part without written
permission is prohibited. All rights reserved.

SAT-HD300

FCC ID:L73RM-Y822A
USER'S MANUAL

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

This product must not be exposed to dripping or splashing liquids. Objects filled with liquids, such as a vase, must not be placed on or above

the product.

NOTE TO CABLE/TV/SATELLITE DISH INSTALLER:

This reminder is provided to call the cable TV system/satellite dish installer’s attention to Article 820-40 of the National Electric Code (U.S.A.).

The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding sys-

tem of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION : FCC PART 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manu-

al, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFI­CIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPOR­TANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

WARNING:

TO REDUCE THE RISK OF ELECTRONIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.

1

2

REGULATORY INFORMATION: FCC Part 68

Sony must make any necessary repairs to the modem portion of this equipment in order to maintain valid FCC registration. Do not attempt to
repair or service the modem.
This equipment cannot be used on public coin service provided by the Telephone Company. Connection to Party Line Service is subject to state
tariffs.

• This product complies with Part 68 of the FCC rules. On the back of this product is a label that contains, among other information, the FCC
registration number and Ringer Equivalent Number (REN) for this product. If requested, this information must be provided to the telephone
company.

• The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line
may result in the devices not ringing in response to an incoming call. Typically, the sum of the RENs should not exceed five (5). To be certain
of the number of devices that may be connected to the line (as determined by the total RENs) contact the local telephone company.

• If this product causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is necessary.

• The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the prod­uct. If this happens, the telephone company will provide advance notice so you can make the necessary modifications to maintain uninter­rupted service.

• Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission, or corpo­rate commission for information.)

• If trouble is experienced with this product, for repair or warranty information, please contact Sony Electronics Inc. If the product is causing
harm to the telephone network, the telephone company may request that you disconnect the product until the problem is resolved.

• An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the tele­phone network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for details.

If you have questions about this Sony product, please contact the Sony Satellite System Information Center at 1-800-838-SONY(7669).
For questions about service, programming or billing, contact DIRECTV at 1-800-DIRECTV (347-3288).

CAUTION

DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY WITHOUT WRITTEN AUTHORIZATION FROM SONY ELECTRONICS CORPORATION.
UNAUTHORIZED MODIFICATION COULD VOID THE USER’S AUTHORITY TO OPERATE THIS PRODUCT.
THIS EQUIPMENT IS INTENDED TO RECEIVE AND DECODE SIGNALS TRANSMITTED ACCORDING TO ATSC DIGITAL TELEVISION STANDARD
A/53, DIRECTV

®

SPECIFICATION AND IS INTENDED TO BE USED WITH AN APPROPRIATE ANTENNA, DISH AND DISPLAY DEVICE THAT YOU

MUST PROVIDE.

Dolby Digital

®

Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.

Macrovision Information

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited pay-per-view uses unless oth­erwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Declaration of Conformity

Trade Name: Sony
Model No.: SAT-HD300
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road, Oradell, NJ 07649
Telephone No.: 201-930-6972

As an ENERGY STA R®Partner,
Sony has determined that
this product or product models
meets the ENERGY STA R

®

guidelines for energy
efficiency.

ENERGY STA R®is a U.S. registered mark.

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MAN-

UAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for
installation, use, and servicing.
This unit does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read these instructions. - All these safety and

operating instructions should be read before the
product is operated.

2. Keep these instructions. - The safety, operating

and use instructions should be retained for future
reference.

3. Heed all warnings. - All warnings on the product

and in the operating instructions should be adhered
to.

4. Follow all instructions. - All operating and use

instructions should be followed.

5. Do not use this apparatus near water. – For

example: near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet basement; or near a swimming
pool; and like.

6. Clean only with dry cloth. – Unplug this product

from the wall outlet before cleaning. Do not use liq­uid cleaners.

7.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

-

Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in instal­lation such as a bookcase or rack unless proper ven­tilation is provided or the manufacturer’s instructions
have been adhered to.

8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa­ratus (including amplifiers) that produce heat.

9.

Do not defeat the safety purpose of the polar­ized or grounding-type plug. A polarized plug
has two

blades with one wider than the other.

A grounding

type plug has two blades and a
third grounding prong. The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet, con­sult an electrician for replacement of the obso­lete outlet.

10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.

11. Only use attachments/accessories specified
by the manufacturer.

12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with apparatus. When a cart is used, use cau­tion when moving the cart/ apparatus combi­nation to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms
or when unused for long periods of time.

14.

Refer all servicing to qualified service person­nel.

Servicing is required when the apparatus
has been damaged in any way, such as
power- supply cord or plug is damaged, liquid
has been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

3

4

IMPORTANT INFORMATION

Due to copyright restrictions, you may not be able to view some high definition programs in
high definition format using this product. If HD viewing is prohibited due to copyright restric­tions, you would need to connect SD interfaces to view the program.

In certain markets, access to local channels requires a DIRECTV

®

Multi-Satellite Dish Antenna.
For the most current information about the availability of local channels in your area, contact
your retailer or visit DIRECTV.com. For access to all High Definition programming, a triple LNB
Multi-Satellite dish antenna, including a Sat C LNB, is required, along with a High Definition
capable DIRECTV

®

HD Receiver and High Definition television. Satellite Dish Antenna Sold

Separately.

Activation of programming may be subject to credit approval and requires valid service
address, social security number and/or major credit card. Deposit or prepayment may be
required. Programming subject to change. You must be physically located in the U.S. to receive
DIRECTV service. DIRECTV services not available outside the U.S. DIRECTV programming is
sold separately and independently of DIRECTV System hardware. A valid programming sub­scription is required to operate DIRECTV System hardware. Activate your DIRECTV program­ming today at 1-800-DIRECTV (1-800-347-3288)

DIRECTV, the Cyclone Design logo and Advanced Program Guide™ are trademarks of DIRECTV,
Inc., a unit of Hughes Electronics Corp., and are used with permission.

Sony Hi-Scan and the Sony logo are registered trademarks of Sony.

Sony Software License Agreement

ATTENTION:USE OF THE SOFTWARE IS SUBJECT TO THE SONY SOFTWARE LICENSE TERMS
SET FORTH ON PAGE 121. USING THE SOFTWARE OR THE PRODUCT IN WHICH IT IS INCOR­PORATED INDICATES USER’S ACCEPTANCE OF THESE LICENSE TERMS. IF THE USER DOES
NOT ACCEPT THESE LICENSE TERMS,THE USER SHOULD IMMEDIATELY RETURN THE ENTIRE
PRODUCT IN ITS ORIGINAL PACKAGING IN ORDER TO RECEIVE A FULL REFUND OF THE PUR­CHASE PRICE.

5

TABLE OF CONTENTS

Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .3

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

1. Introduction 1-1. A New World of Digital Entertainment . . . . . . . . . . . . . . . .7

1-2. Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2. Important Overview 2-1. Sending Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2-2. TV Signal Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2-3. Display Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2-4. Normal and Wide Format Signals . . . . . . . . . . . . . . . .12-13

2-5. Audio Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15

2-6. On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17

3. Setup and Connections 3-1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19

3-2. Back Panel of the DIRECTV

®

HD Receiver . . . . . . . . . .20-21

3-3. General Recommendations . . . . . . . . . . . . . . . . . . . . . . . .22

3-4. Connecting to Antennas . . . . . . . . . . . . . . . . . . . . . . .23-26

3-5. TV Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-30

3-6. VCR Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-32

3-7. Audio Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .33-34

3-8. Remote Control RF Antenna Connection . . . . . . . . . . . . . .35

4. Front Panel and 4-1. Using the Front Panel of the DIRECTV

®

HD Receiver . . . . .36

4-2. Using the Remote Control . . . . . . . . . . . . . . . . . . . . . .37-39

4-3. Programming the remote control . . . . . . . . . . . . . . . . . . . .40

4-4. Remote Control Codes for Other Components . . . . . . .41-42

5. Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

6. Basic Operation 6-1. Viewing the Channel Banner . . . . . . . . . . . . . . . . . . . .44-45

6-2. Surfing Favorite Channels . . . . . . . . . . . . . . . . . . . . . . . . .46

6-3. Freeze Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

6-4. Subscription to DIRECTV

®

programming and

ANT/CABLE-Only operation . . . . . . . . . . . . . . . . . . . . . . .48

6

7.

Advanced Program Guide™

7-1. About the Advanced Program Guide™ . . . . . . . . . . . . . . .49

7-2. Layout of the Advanced Program Guide

™ Screen . . . .50-51

7-3. Moving through the Advanced Program Guide

™ . . . . .52-53

7-4. Selecting a Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

7-5. Getting More Program Information . . . . . . . . . . . . . . .55-56

7-6. Setting a Timer/Record Event for Future Viewing . . . . . . .57

7-7. Purchasing DIRECTV

®

Pay Per View Programs . . . . . . . . . .58

7-8. Searching for Programs by Category . . . . . . . . . . . . . .59-60

7-9. Searching for Programs by Keyword . . . . . . . . . . . . . . . . .61

8. Customization 8-1. Accessing the On-screen Menu . . . . . . . . . . . . . . . . . . . .62

8-2. The structure of the On-Screen Menu . . . . . . . . . . . . . . . .63

8-3. Managing Program Purchases . . . . . . . . . . . . . . . . . . . . .64

8-4. Checking the Messages . . . . . . . . . . . . . . . . . . . . . . . . . .65

8-5. Setting a Timer/Record Event . . . . . . . . . . . . . . . . . . . . . .66

8-6. Modifying a Timer/Record Event . . . . . . . . . . . . . . . . . . . .67

8-7. Initializing the System . . . . . . . . . . . . . . . . . . . . . . . . .68-75

8-8. Managing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . .76-79

8-9. Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80-81

8-10. Setting Default Signal Out . . . . . . . . . . . . . . . . . . . . . . .82

8-11. Hook-up Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

8-12. Setting the Audio . . . . . . . . . . . . . . . . . . . . . . . . . . .84-88

8-13. Choosing the Aspect Ratio . . . . . . . . . . . . . . . . . . . . .89-91

8-14. Setting Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . .92

8-15. Setting Digital Caption Style . . . . . . . . . . . . . . . . . . . . . .93

8-16. Setting Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . .94

8-17. Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

8-18. Running Auto Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

8-19. Setting Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97-102

8-20. Getting the System Information . . . . . . . . . . . . . . .103-106

8-21. Testing the System . . . . . . . . . . . . . . . . . . . . . . .107-109

8-22. Replace Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110

8-23. VCR Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

8-24. Remote Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . .112

9. Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113-114

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116-119

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120

Software License Agreement . . . . . . . . . . . . . . . . . . . . . . . . .121

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

7

1-1. A New World of Digital Entertainment

Welcome to the SAT-HD300 DIRECTV®HD Receiver, an advanced digital satellite receiver that show­cases a new generation of digital entertainment.

The DIRECTV HD Receiver delivers a variety of programs from DIRECTV and has a built-in HD Receiver
that serves as a digital receiver that makes it possible to view digital programs even on your analog TV.

The Advanced Program Guide™ delivered via satellite service also enables you to access and view
over-the-air broadcasts and cable as well as DIRECTV

®

programming.

1. INTRODUCTION

8

Ultimate Entertainment

• A Wide Variety of Programs

Hundreds of channels are available by subscription from DIRECTV.

• DIRECTV Advanced Program Guide

TM

Instant access to up to seven days of program listings.
Ability to jump a day or 6 hours at a time.
Ability to search and tune by program title, keyword and category.

Technical Flexibility

• Seamless Tuning

Tune seamlessly to over-the-air, cable and satellite.

• Multiple Output Jacks

Multiple output jacks are provided on the back panel of the DIRECTV

®

HD Receiver ensuring

maximum connectively to a variety of display devices.

• Screen Format Adaptability

Various screen formats are available including 1080i, 720p, 480p, 480i, variable 1, variable 2,
variable 3, auto DVI, and true native modes.

• ANT/CABLE Only Mode

Viewing analog/digital broadcasting with an over-the-air antenna and cable service.

• Simultaneous 480i Display Output

Supporting simultaneous 480i Display Output for VCR-recording or viewing on an analog TV.

Superior Performance

• Crisp Picture

High-Definition or resolution with a 16:9 aspect ratio when connected to a high definition moni­tor.

• Superior Sound

Sensational sound with Dolby Digital

®

5.1 channels when connected to a Dolby Digital®compati-

ble audio receiver system.

• DVI-HDTV Output

For an all-digital connection to DVI-HDTV monitors.

• RF Remote Control

Remote control access from outside a cabinet or even from another room within your home.

Convenient Use

• Help

Easy-to-use on-screen menus with instant spot help and brief on-screen user’s guide.

• Hook-up Help

The on-screen menus show connection schemes on the DIRECTV HD Receiver.

• Setup Wizard

Easy-to-use Wizard based System Setup

• Easy Recording to VCR

Up to seven days of program guide information from which shows can be quickly selected for
automatic VCR recording.

1-2. Main Features

2-1. Sending Signals

9

2. IMPORTANT OVERVIEW

Digital broadcasting is a new way of sending programs over the airwaves with superior qual­ity video and audio. The DIRECTV

®

HD Receiver enables you to take full advantage of digital

broadcasting. To fully enjoy it, it is helpful understand the ways the program signals are sent.

There are two types of TV signal formats; analog (often called NTSC format; National Television
System Committee) and digital (ATSC format; Advanced Television System Committee). Digital
formats are classified into three categories: High Definition (HD), Enhanced Definition (ED), and
Standard Definition (SD) according to the resolution or digital picture quality.

There are also three ways that program signals can be received; over-the-air (NTSC, ATSC),
cable (analog and digital), and satellite.

This receiver contains a QAM tuner which should allow you to receive unscrambled QAM dig­ital television programming via subscription service to a cable service provider. This receiver
will not be able to tune encrypted (scrambled) digital programming or advanced interactive
digital cable services. Contact your local cable service provider for further information regard­ing the availability of unscrambled digital cable programming.

Satellite

Sat A 101

DIRECTV

Sat B 110 Sat C 119

TV

HD Receiver

Phone
Jack

Digital

Analog

signal

signal

Unscrambled
Analog Cable service

Unscrambled
Digital Cable service

Signal Format Analog

Digital

SD HD

10

2-2. TV Signal Formats

The digital TV standards allow several different formats. Broadcasters can choose between
three formats:

• 480p - The picture is 704 x 480 pixels, sent at 60 complete frames per second (480i is
also possible).

• 720p - The picture is 1280 x 720 pixels, sent at 60 complete frames per second.

• 1080i - The picture is 1920 x 1080 pixels, sent at 60 interlaced frames per second (30
complete frames per second).

(The “p” and “i” designations stand for “progressive” and “interlaced.” In a progressive for­mat, the full picture updates every sixtieth of a second. In an interlaced format, half of the pic­ture updates every sixtieth of a second.)

The 480p and 480i formats are called the SD formats, and 480i is roughly equivalent to a nor­mal analog TV picture. The 720p and 1080i formats are called the HD formats.

Some analog televisions can display a picture 720 pixels wide by 480 pixels high, that’s a total
of 345,600 pixels. HD digital signals can have a maximum resolution of 1920 x 1080, that’s
2,073,600 pixels, or six times more pixels than the older resolution. Pictures will be crisper and
cleaner, with more detail in every close-up and every panorama.

Standard Comparison Table

Active Lines 480i 480p 720p or 1080i

Sound Stereo (2 ch)

Dolby Digital®(5.1 ch) Dolby Digital (5.1 ch)

MPEG Audio (2 ch)

Aspect Ratio 4 : 3 4 : 3 or 16 : 9 16 : 9

Resolution 720 x 480

640 x 480 1280 x 720

704 x 480 1920 x 1080

2. IMPORTANT OVERVIEW

11

2-3. Display Formats

The DIRECTV®HD Receiver provides several display formats. The FORMAT button in the front
panel changes the display format in the cycle of 1080i, 720p, 480p, 480i, native,
variable 1, variable 2, variable 3 and Auto DVI** modes. In 1080i, 720p, 480p and 480i
modes, all input signal formats are converted to the chosen display format. In native, vari-
able 1, variable 2 and variable 3 modes, output display format is automatically adapted
depending on input signal format. In Auto DVI mode, the output display format is automati­cally adapted based on the preferred resolution format of the DVI-HDTV monitor. The format
may be converted from the original broadcast format.

* Only one of the YPbPr, RGB or DVI-HDTV jacks is available at any one time, depending on

the TYPE switch setting and DVI-HDTV connection status.

** Format available when using the DVI-HDTV output to connect to a DVI-HDTV monitor.

OUTPUT CONNECTION AVAILABLE FORMATS

YPbPr* 1080i/720p/480p/480i/native/variable 1/variable 2/variable 3

RGB* 1080i/720p/480p/native/variable 1/variable 2/variable 3

DVI-HDTV* 1080i/720p/480p/480i/native/variable 1/variable 2/

variable 3/Auto DVI**

Video 1 / 2 All formats converted to 480i

S Video All formats converted to 480i

RF Out to TV All formats converted to 480i

T

Y

COMPONENT OUT
(1080ii/720p/480p/480ii)

Pr

Pb

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DVI-HDTV OUT

(1080ii/720p/480p/480ii)

(

1

2

VIDEO OUT

S VIDEO

OUT

OUT TO TV

Display Format modes Input Signal format Output Signal format

1080i all formats 1080i

720p all formats 720p

480p all formats 480p

480i all formats 480i

native 1080i 1080i

720p 720p

480p 480p

480i 480i(Component, DVI), 480p(RGB)

variable 1 1080i 1080i

720p 720p

480p/480i 480p

variable 2 1080i/720p 1080i

480p/480i 480p

variable 3 1080i/720p 720p

1080i 480p

AUTO DVI** all formats changes according to monitor type

12

2-4. Normal and Wide Format Signals

When you view a high definition picture with 480i or 480p format setting, the WIDE MODE but­ton on the remote control changes the wide mode in the cycle of Letterbox, Cropped, to
Squeezed.
When you view a standard definition picture with 720p or 1080i format setting, the WIDE
MODE button on the remote control changes the wide mode in the cycle of Normal, Wide,
Panorama, Zoom, to Cine-Zoom. (Refer to section 8-13, ‘Choosing the Aspect Ratio’)

Standard Definition

Standard Definition Output Format

No Adjustment Options

High Definition

WHEN YOU SET THE FORMAT TO SDTV (480i/480p)

Letter box

Choose when you want to view a
wide format (16:9) picture on a nor­mal screen (4:3) without squeezing.

Cropped

Choose when you want to view a
picture filling the entire screen
while keeping the wide format.
Left and right portions of the pic­ture will not be shown.

Squeezed

Choose when you want to view a full
picture filling the entire screen with
no black bars. The picture in a 16:9
format will be horizontally adjusted or
squeezed to fit the 4:3 ratio monitor.
This setting can also be useful when
used with 16:9 aspect ratio monitors
or with 4:3 aspect ratio monitors with
a “16:9 enhancement” feature.

antenna

Program Format

13

2. IMPORTANT OVERVIEW

2-4. Normal and Wide Format Signals

WHEN YOU SET THE FORMAT TO HDTV (1080i/720p)

Normal

Choose when you want to view a picture
with an original 4:3 aspect ratio on your
16:9 TV. Black or gray bars will show at the
left and right sides.

Wide

Choose when you want to evenly stretch the
width of a normal picture to fill the entire
screen.

Panorama

Choose when you want to evenly stretch the
edges of a normal picture to fill a wide
screen.

Zoom

Choose when you want to fill the entire
screen with the picture. The image will be
altered both horizontally (stretched) and
vertically (cropped). The top and bottom
portions of the picture will not be shown.
Zoom1 shows you the picture with a trade­off between distortion and screen coverage.

CINE-Zoom

Choose when you want to adjust zooming.

Standard Definition

High Definition

*Three temporary adjustment options available

Adjustment

Required

antenna

Program Format

High Definition Output Format

*Note.
The HDTV formats should always be broadcast in the 16:9 aspect ratio.
However, you may choose one of three temporary options to select for your
preference. The three options are Standard , Expand and Shrink.

14

2-5. Audio Signals

Dolby Digital Sound with 5.1 Channels

sub-woofer

right
speaker

left

speaker

center channel
speaker

surround

sound

speaker

surround
sound
speaker

Digital Audio Signals

The DIRECTV®HD Receiver will be the focal center of your home entertainment system comprising a
variety of components, such as TV, DVD, VCR, etc. and external audio systems. Since digital programs
being broadcast contain digital-quality audio, you can create a home theater by sending audio signals
from the DIRECTV HD Receiver to your audio system externally. HD digital signals use the Dolby
Digital

®

audio encoding system - the same digital sound used in many movie theaters, on DVDs, and

in many home theater systems.

When you tune to a channel, the DIRECTV HD Receiver can send signals either to a Dolby Digital

®

decoder/receiver or to a PCM (normal digital) decoder. (* Refer to Section 3-7 Connection for Audio
for making the required external connections to your system.)

Dolby Digital®audio, formally known as Audio Coding 3rd Generation is a
coding technique that can provide up to five independent, full frequency
response audio channels (three in left, center, and right, two in rear left
and right,) and one low frequency effect for a sound you can feel.

GLOSSARY

15

The analog audio outputs may be used to drive an external Hi-Fi audio system instead of the
TV speakers. These stereo outputs are activated by setting the Analog Mode in the Audio
menu to Stereo.

If you set the Analog Mode to SAP (Second Audio Program), you can hear the program’s dia­log in another language such as French or Spanish, if provided on the analog broadcast.

(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT

(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

(1080ii/720p/480p/480i

VIDEO OUT

Analog stereo amplifier

AUDIO IN

Audio cables

Analog Audio Signals

2-5. Audio Signals

2. IMPORTANT OVERVIEW

16

2-6. On-Screen Display

Advanced Program Guide™

The DIRECTV Advanced Program Guide™ is an on-screen listing of current and future pro­grams that are available from DIRECTV. The DIRECTV

®

HD Receiver offers you a comprehen­sive program list that contains information about programs with hundreds of channels, includ­ing analog Antenna and digital (ATSC). If you do not subscribe to DIRECTV

®

programming, you

will not be able to see the Advanced Program Guide™.

Main Menu

You can adjust the setup through a user-friendly on-screen menu using the remote control.
While viewing a program, the on-screen menu will appear on your TV screen if you press the
MENU button on your remote control. The on-screen menu is operated using a simple,
straight-forward ‘Highlight and Select’ process. You just highlight a menu item by using
“

DEF G ” on your remote control, and select it by pressing “ ”. The on-screen menu also

offers visual cues for easy guidance.

17

3. SETUP AND CONNECTIONS

2-6. On-Screen Display

Help

First, certain features and terminologies used in the on-screen menus require your basic
understanding to fully utilize their capabilities. The DIRECTV

®

HD Receiver provides a power-

ful feature called “Help” that describes highlighted menu item to help you understand the fea­tures. Press and hold the “HELP” button to display the “Help”. Once you release the button,
the Help menu disappears from the screen.

Second, if you press the “HELP” button while you are viewing a program with no menus on ­screen, the DIRECTV HD Receiver provides a comprehensive on-screen user’s guide. It
describes how to use your receiver.
This is, in fact, an on-line version of this Operating Guide.

18

3-1. Unpacking

Make sure you have received all these items listed below with the DIRECTV®HD Receiver.

Remote Control

Cables

Remote Control
RF Antenna

Batteries

Access Card

POWER

SLEEP TV

MUTING

TV

TV/VIDEO

INFO

FREEZE

SIGNAL WIDE

CODE SET

FUNCTION

FLIP OPEN

FAVORITE

N

E

M

E

X

I

HELP CC

RM-Y822

U

T

SAT

SAT

PIC MODE

ENTER

GUIDE

CHVOL

PREV CH

MODE

S VIDEO Jack

Audio/Video Jacks

OUT TO TV

Phone Jacks

YPB

Component Jacks

AA

AA

ACCESS
CARD

PR

DVI-HDTV Jack

VCR

CONTROL

19

3. SETUP AND CONNECTIONS

3-1. Unpacking

DIRECTV®HD Receiver

The DIRECTV HD Receiver is capable of receiving signals from the satellite dish, cable, and/or over-the-air
antenna and sending the decoder signals to your TV.

Remote Control

In addition to the DIRECTV HD Receiver, the remote control can be programmed to control many other
devices.

Batteries

To install the batteries, slide open the battery compartment and insert the two AA batteries provided.

Component Out Jacks and Cables

Component Cables are used to connect the DIRECTV HD Receiver to an industry standard Y/Pb/Pr compat­ible Monitor.

DVI-HDTV port and Cable

DVI cable is used to connect the DIRECTV HD Receiver to a DVI-HDTV compatible HD monitor.

S-Video Jack and Cable

An S-Video jack is provided on the DIRECTV HD Receiver and is used together with audio cables.
Remember to connect the left and right audio cables. An S-Video jack carries only the picture signals, not
the sound.

Audio/Video Jacks and Cables

The Audio/Video jacks provide good picture and sound quality. They are used for making most Audio/Video
connections between components. The Audio/Video jacks may be color coded (yellow for video, red for
right audio, and white for left audio). If your component has only one input for audio (mono), connect it to
the left (white L/mono) audio jack on the DIRECTV HD Receiver.

RF (Radio Frequency) Jacks and Coaxial Cables (F-type)

RF jacks are necessary for reception of over-the-air broadcasts, cable, and DIRECTV signals. These jacks
are also required for antenna or cable connections. The RF and coaxial jacks on the DIRECTV HD Receiver
are labeled Antenna, Cable, Satellite and OUT TO TV. An RG-6 type coaxial cable is required for satellite
signal distribution.

Telephone Jack and Cord

A telephone line cord is required to connect the DIRECTV HD Receiver to a phone line. If you choose to sub­scribe to DIRECTV

®

programming, this phone line is required to be connected.

Access Card

The Access Card is the means by which DIRECTV controls the distribution of its service. The card must be
inserted into the access card slot (on the front of the DIRECTV HD Receiver) at all times to ensure recep­tion of satellite signals.

Remote Control RF Antenna

The Remote Control RF Antenna can be used with the supplied remote control.

VCR Controller

The VCR Controller allows the Record function to automatically operate your VCR.

20

3-2. Back Panel of the DIRECTV®HD Receiver

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT
(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

Ant In

Is used to connect an over-the-air or terrestrial antenna.

Cable In

Is used to connect a coaxial cable coming from your cable TV service outlet or cable box.

Out to TV

Provides an RF connection between the DIRECTV HD Receiver and older TVs. All decoded signals are
provided on channel 3 or 4 as selected in the Output Channel section of the SETUP menu. When the
DIRECTV HD Receiver is in the standby mode, Cable or Antenna signals are passed through as chosen
in the Out to TV section of the Preference menu.

Video Out 1, 2

Is used to provide baseband composite video signal to a VCR or TV set. Video connection generally
provides picture quality that is superior to RF connections. For a better quality picture connection, use
the S-Video jack if it is available.

Component Out

Is used to connect to a Y/Pb/Pr-compatible monitor. Three video and two audio jacks for a Y/Pb/Pr
monitor need to be connected and the TYPE switch must be set to left position.

RGB/DVI-HDTV Out

Is used to connect to either an RGB compatible or DVI-HDTV monitor. Either an RGB port for an RGB
monitor or a DVI-HDTV port for a DVI-HDTV monitor need to be connected and the TYPE switch must
be set to right position.

Note : The DVI-HDTV port has a higher priority when both the RGB and DVI-HDTV ports are connected.

Note: For best access to High-Definition Programming from DIRECTV, connect the DVI-HDTV output to
a DVI-HDTV input on your high-definition TV or monitor. A DVI-HDTV input is one that is compliant
with EIA-861 and HDCP specifications. Check your TV or monitor’s user manual to find out if the TV or
monitor’s DVI input is compliant with these specifications.

21

3. SETUP AND CONNECTIONS

3-2. Back Panel of the DIRECTV®HD Receiver

Audio Out 1,2

Is used to provide analog audio signals to VCR, TV set, HD Monitor, or Hi-Fi System.

Digital Audio Out

Is used to connect a digital optical cable from the DIRECTV HD Receiver to the Dolby Digital

®

receiver
or decoder. Dolby Digital audio enables the viewer to experience theater-quality sound using up to 5.1
audio channels when available audio in the broadcast.

Data Port

Can be used to communicate with certain compatible devices, such as Personal Video Recorders.

VCR Control

Is used to connect the VCR Controller cable to your receiver.

RF Remote

Is used to connect the RF Remote control antenna to your receiver.

Phone Jack

Is used to connect a phone line.

Satellite In

Is used to connect a satellite dish antenna to your receiver.

22

3-3. General Recommendations

You can connect the DIRECTV®HD Receiver in a variety of configurations. The answers to the follow­ing questions will determine the correct setup for you.

- What type of antennas do you have? Satellite dish, cable, and/or over-the-air antennas.

- What type of connectors does your TV or VCR have: Y/Pb/Pr, RGB, DVI-HDTV, S-VIDEO, A/V (RCA­type), or RF coaxial?

- Do you have an external audio or audio/video system? Consider integrating the DIRECTV HD
Receiver into a home theater configuration to take advantage of the audio capabilities of your Dolby
Digital

®

System (Digital) or Hi-Fi System (Analog).

- Does your TV have Y/Pb/Pr connectors? Use it to connect your TV to the DIRECTV HD Receiver. An
Y/Pb/Pr connection provides a better picture than S-VIDEO, RCA-type video, or RF connections.

- Does your TV have an S-VIDEO jack? Use it to connect your TV to the DIRECTV HD Receiver.
An S-VIDEO connection provides a better picture than RCA-type video or RF connections.

- Does your TV have RCA-type A/V connectors, but no S-video jack? Use your TV’s A/V connectors to
connect your components. An A/V connection provides better picture and audio when compared to
an RF connection.

Although there are numerous connections possible for optimum video and audio performance, try to fol­low the guidelines listed below when you hook up your components. Detailed hook-up instructions are
provided on the following pages.

Protect your components from power
surges by turning off the component and
unplugging power cords when you make
connections.
Protect your component from overheat­ing by keeping the ventilation holes
open and not stacking components.

No Dish
Round Dish (Satellite A)
Oval Dish (Satellite A, B)
Oval Dish (Satellite A, B, C)

Analog TV
HD Monitor (Y/Pb/Pr type)
HD Monitor (RGB type)
HD Monitor (DVI-HDTV type)

VCR
Digital Audio System
Analog Hi-Fi System

23
24
25
26

27
28
29
30

31
33
34

To Antennas

To TV/Monitor

To A/V Systems

Connection

Component

Page

CAUTION: Make all connections before plugging the power supply cord into a standard 120V, 60Hz AC
power outlet.

23

3. SETUP AND CONNECTIONS

3-4. Connecting to Antennas - Non-Satellite Sources

Receiving Signals

1. Connect the “Antenna” to the “ANT IN” jack on the DIRECTV

®

HD Receiver using a coaxial

RF cable.

2. Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a

coaxial RF cable.

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT
(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

Antenna

Cable TV
wall jack

24

3-4. Connecting to Antennas - Round Dish (Satellite A)

Receiving Signals

1.

Connect the “Antenna” to the “ANT IN” jack on the DIRECTV®HD Receiver using a coaxial RF cable.

2.

Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a coaxial RF
cable.

3.

Connect the “Jack 1” of the dish antenna to the “SATELLITE IN” jack on the DIRECTV HD Receiver using
a coaxial RF cable. (For proper dish installation, refer to the “Installer’s Guide” provided with your satel­lite dish antenna.)

4.

Connect the “Phone Wall Jack” to “PHONE JACK” on the DIRECTV HD Receiver using a phone cable.

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT

(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

LNB
Sat A

Dish

Jack 1

Phone wall jack

Antenna

Cable TV
wall jack

NOTE

While you are subscribing to a DIRECTV

®

pro­gramming package, you can still view over-the­air and cable TV programs, if you make con­nections to the over-the-air and/or cable jacks.

NOTE

A triple LNB multi-satellite dish with a SAT
C LNB is required to receive all DIRECTV

®

High-Definition programming, along with
this DIRECTV HD Receiver.

25

3. SETUP AND CONNECTIONS

3-4. Connecting to Antennas - Oval Dish (Satellite A, B)

Receiving Signals

1.

Connect the “Antenna” to the “ANT IN” jack on the DIRECTV®HD Receiver using a coaxial RF cable.

2.

Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a coaxial RF cable.

3.

Connect the “Jack 1” of the multi-switch to the “SATELLITE IN” jack on the DIRECTV HD Receiver using
a coaxial RF cable. (For proper dish installation, refer to the “Installer’s Guide” provided with your satellite
dish antenna.)

4.

Connect the “Phone Wall Jack” to “PHONE JACK” on the DIRECTV HD Receiver using a phone cable.

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT

(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

LNB
Sat B

LNB
Sat A

Dish

5x4 Multi-switch

Output

Phone wall jack

Antenna

Cable TV
wall jack

NOTE

While you are subscribing to a DIRECTV

®

programming package, you can still view
over-the-air and cable TV programs, if you
make connections to the over-the-air and/or
cable jacks.

NOTE

A triple LNB multi-satellite dish with a SAT
C LNB is required to receive all DIRECTV

®

High-Definition programming, along with
this DIRECTV HD Receiver.

26

3-4. Connecting to Antennas - Oval Dish (Satellite A, B, C)

Receiving Signals

1.

Connect the “Antenna” to the “ANT IN” jack on the DIRECTV®HD Receiver using a coaxial RF cable.

2.

Connect the cable TV signal to the “CABLE IN” jack on the DIRECTV HD Receiver using a coaxial RF cable.

3.

Connect the “Jack 1” of the multi-switch to the “SATELLITE IN” jack on the DIRECTV HD Receiver using a
coaxial RF cable. (For proper dish installation, refer to the “Installer’s Guide” provided with your satellite dish
antenna.)

4.

Connect the “Phone Wall Jack” to “PHONE JACK” on the DIRECTV HD Receiver using a phone cable.

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT
(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

Phone wall jack

LNB
Sat B

LNB
Sat C

LNB
Sat A

Dish

5x4 Multi-switch*

Output

Antenna

Cable TV
wall jack

NOTE

While you are subscribing to a DIRECTV

®

program­ming package, you can still view over-the-air and
cable TV programs, if you make connections to the
over-the-air and/or cable jacks.

NOTE

A triple LNB multi-satellite dish with a SAT
C LNB is required to receive all DIRECTV

®

High-Definition programming, along with
this DIRECTV HD Receiver.

* Sat C may also be connected via a SAT B/SAT C combiner with a 4x4 multi-switch (not supplied by Sony).

27

3. SETUP AND CONNECTIONS

3-5. TV Connection - Analog TV

TV Viewing

1.

Connect the “OUT TO TV” jack on the DIRECTV®HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.

2.

Connect the “AUDIO OUT” and “VIDEO OUT” jacks on the DIRECTV HD Receiver to the “A/V IN” jack on your TV
using RCA-type cables.

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT

(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

Phone wall jack

L

Analog TV

ANT.IN V R

LNB
Sat B

LNB
Sat C

LNB
Sat A

Dish

5x4 Multi-switch

Output

Antenna

Cable TV
wall jack

28

3-5. TV Connection - HD Monitor (Y/Pb/Pr type)

TV Viewing

1.

Connect the “OUT TO TV” jack on the DIRECTV®HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.

2.

Connect the “COMPONENT OUT” jacks on the DIRECTV HD Receiver to the “COMPONENT IN” jacks of your TV
using RCA-type cables. (The “TYPE” switch must be set toward the “Y/Pb/Pr” jacks.)

3.

Connect the L/R “AUDIO OUT” jacks on the DIRECTV HD Receiver to the L/R “AUDIO IN” jacks on your TV using
RCA-type cables.

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT

(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

HD-Ready TV

ANT.IN Y Pb PrLR

Phone wall jack

LNB
Sat B

LNB
Sat C

LNB
Sat A

Dish

5x4 Multi-switch

Output

Antenna

Cable TV
wall jack

29

3. SETUP AND CONNECTIONS

3-5. TV Connection - HD Monitor (RGB type)

(1080i/720p/480p)(1080i/720p/480p)

RGB OUT

DATA PORT

DVI-HDTV OUT

SATELLITE

IN

TYPE

CABLE IN

ANT IN

OUT TO TV

Y

COMPONENT OUT

(1080ii/720p/480p/480ii)

Pr

1

L2

R2R1

L1

2

AUDIO OUT

Pb

OPTICAL

DIGITAL

AUDIO

OUT

S VIDEO

OUT

VCR

CONTROL

RF

REMOTE

(1080ii/720p/480p/480ii)

PHONE

JACK

VIDEO OUT

HD-Ready TV

ANT.IN Y Pb PrLR

Phone wall jack

LNB
Sat B

LNB
Sat C

LNB
Sat A

Dish

5x4 Multi-switch

Output

Antenna

Cable TV
wall jack

TV Viewing

1.

Connect the “OUT TO TV” jack on the DIRECTV®HD Receiver to the “ANT IN” jack on your TV using a coaxial
RF cable.

2.

Connect the “RGB OUT” jack on the DIRECTV HD Receiver to the “RGB IN” jack of your TV using VGA-type connec­tor. (The “TYPE” switch must be set toward the “RGB/DVI-HDTV” jacks.)

3.

Connect the L/R “AUDIO OUT” jacks on the DIRECTV HD Receiver to the L/R “AUDIO IN” jacks on your TV using
RCA-type cables.

Note : The RGB OUT jack supports 480p, 720p, and 1080i formats.