Sanuvox SABER GENIUS User Manual
OPERATION
To start the purifier, press the 'ON' button. The LCD screen is illuminated
to show that power is on. Within a few seconds, the UV lamp will energize.
SABER GENIUS
INSTALLATION
MANUAL
SABER GENIUS
MANUAL
24 / 110 VOLT UV SYSTEM
LAMP OPERATING STATUS
Days LeftDays Left
A
EC2
G
365
B
F
C
Error-Code
EC1: Lamp failure
EC2: Ballast failure
EC3: 24V Power supply voltage too low**
EC4: 24V Power supply voltage too high**
**In the event EC3 or EC4 appears, the 110/24V
step down transformer must be used.
MAINTENANCE
G
E
D
A. Day Counter - Provides lamp life remaining in days.
B. UV Lamp Status - “UV Purifier Operating” will show unless:
Unit is OFF
Lamp has failed
Ballast has failed
Lamp is over 365 day life
C. Change Lamp Indicator - After 325 days, CHANGE LAMP
will illuminate, indicating that lamp will need to be replaced
soon. After 365 days, CHANGE LAMP will flash indicating
it is time to replace lamp. CHANGE LAMP will also stay on
if the lamp fails before the 365 days is up.
D. Timer - Rotating Circle indicates time counter. It will stop rotating
after 365 days.
E. Day Counter - Bars will reduce in number each 45 days to
indicate lamp life left. At 365 days, no bars will be
displayed indicating the lamp should be replaced.
F. CALL INSTALLER icon will illuminate under the following
conditions: 1) The Lamp has illuminated for 365 days and is in
need of replacement; 2) when an Error-Code (i.e. EC3) appears.
Days Left
3
65
WARNING
Before installing or performing maintenance or service
on the purifier, DISCONNECT from main power.
Electrical shock can cause injury or death.
EN
Follow all safety codes.
Wear safety glasses and work gloves.
Disconnect all power before performing any maintenance or service. The ultraviolet lamp should be cleaned every two to three months. To clean,
open the control box by loosening screws and pulling cover off. Next, disconnect white socket from lamp. Loosen the 3 screws on the retainer
ring. Turn retainer ring left. Pull out lamp (leave it in retainer ring). Wipe lamp with a soft tissue and alcohol based solution. Reverse the above
procedure to reinstall the lamp. Lamps need periodic replacement to maintain design specifications. Replace lamp after 1 year of operation.
Follow instructions below on how to Reset the Timer Feature. Contact a local dealer for replacement lamps
The 'RESET Button' is used to:
1) Reset an error code without losing 'DAYS LEFT'
2) Reset the unit back to original factory condition. This
includes resetting the 'Lamp Timer' feature back to 365 days.
Soft Reset
A 'Soft Reset' is used to clear an error-code message, or used after a
service call without resetting the lamp life timer.
To do a Soft Reset quickly press the reset button.
Hard Reset
A hard reset is used after a UV Lamp has been replaced with a new
Lamp. Using the Hard Reset will bring the unit back to Factory Condition
including resetting the Days Left to 365.
To do a Hard Reset press and hold the reset button for a minimum
of 3 seconds.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
REV. 01 051210
Or
Troubleshooting the UV Lamp
Disconnect the white socket from the Lamp. Ohmmeter required.
Place one probe of the ohmmeter to one of the four pins on the end of the Lamp.
Touch the other probe of the ohmmeter to each of the other three pins until you
find the matching pin. The ohmmeter will read approximately 3 ohms (almost a
short). This indicates that the filament is good. Check the other two pins. If both
sets of filaments test OK, the Lamp is functioning. If one or both sets of filaments
read an open circuit (infinity) on resistance, the Lamp is defective.
WARNING
Never expose eyes or skin to ultraviolet light from any
source. The Purifier MUST be DISCONNECTED from
power source before performing maintenance or
service. Personal injury may result.
WARNING
Do not touch Lamp glass without gloves. Reduced
performance of Lamp may result. Clean Lamp after
handling.
WARNING
The UV Lamp contains a small quantity of mercury. If a
Lamp breaks, clean and dispose of with care.
WARNING
Use only specified replacement Lamps with your
Purifier. Use of an incorrect Lamp can result in damage
to the Purifier and/or Lamp.
PLEASE SAVE FOR YOUR RECORDS
Serial Number#
Date Installed:
Installed By:
Installers Contact info.:
SANUVOX TECHNOLOGIES INC. © 2010
REV. 01 051210
1-888-SANUVOX www.sanuvox.com
SABER GENIUS
INSTALLATION
MANUAL
SAFETY CONSIDERATIONS
Installation and servicing of air-conditioning equipment can be
hazardous due to system pressure and electrical components. Only
trained and qualified service personnel should install, repair, or service
air conditioning equipment. Untrained personnel can perform basic
maintenance functions such as changing lamps. Trained service
personnel should perform all other operations. When working on air
conditioning equipment, observe precautions in the literature, tags and
labels attached to the unit or accessory, and other safety precautions
that may apply. Follow all safety codes. Wear safety glasses and work
gloves.
GENERAL
365
Figure A. Saber GENIUS
sDay Left
UVC Lamp
Front Cover
3” LCD Display
Power Button
Reset Button
The ultraviolet object purifier is designed to kill odor causing bacteria,
viruses, mold and fungus that may be transmitted through the ducts of
the HVAC (heating ventilation, and air conditioning) equipment. The
ultraviolet purifier is installed so that the UV rays treat the coil of the
HVAC unit. It can be installed in the supply section inside the HVAC
evaporator “A” coil facing into the HVAC evaporator coil, or from the top
of the coil, shining onto the coil. The purifier is simple and easy to install
in an existing HVAC unit and incorporates a quick release mechanism to
clean or replace the lamp.
**IMPORTANT NOTE**
The Saber Genius is designed to operate on 24vac. DO NOT CONNECT THE TWO CONDUCTOR WIRE SET TO 110 VAC.
A 110/24 volt step down transformer is provided in the event that a 24 vac source is not available or is insufficient
(Error Code EC3 or EC4 on Display). In order to install the Saber Genius using the 110/24 step down transformer please
refer to the heading titled “Important Wiring Instructions”
INSTALLATION
The preferred location for installation of the purifier is inside of the HVAC evaporator coil or on the top of the HVAC evaporator coil.
Ultraviolet light may damage certain plastics and exposed non-UV-C (ultraviolet energy, C-Band) protected wires or drain pan. If the
purifier is installed in the supply plenum or over the evaporator coil, the drain pan (if plastic) should be protected from any UV rays.
Cover the exposed area with reflective material such as metal tape or aluminum foil. Ensure site can be supplied with the necessary
power receptacle and that there is adequate clearance for service. Wrap exposed plastic and wiring. The purifier can be mounted in a
horizontal or vertical position. More than one unit can be used if necessary.
Sample Installations
Sample Installations
Mount Purifier on unit. Perform the following procedure to install the purifier:
1. Do not plug in purifier.
2. Evaluate the ideal area for locating and installing the purifier. Ensure that the purifier will fit into the plenum. Space required
internally is approximately 15 inches. If the drain pan is plastic, it must be protected with a reflective material, such as metal
tape or aluminum foil.
3. Ultraviolet light may damage certain plastics and exposed non-UV-C (ultraviolet energy, C-Band) protected wires or drain
pan. Wrap exposed plastic and wiring.
4. Remove the control box from its package. Remove the cover of the control box from the back plate by loosening the screws
on the sides of the box 1 to 2 turns. Pull the backplate off by inserting a finger in the 3/4” diameter hole and pulling back.
5. Using the backplate as a template, mark off the four corner holes and the center of the lamp access hole to be cut in the
plenum.
6. Drill the four corner holes 1/8" diameter and drill a 1" hole in the center.
LAMP INSTALLATION
7. Secure the control box to the plenum using four sheet metal screws. NOTE: Safety switch must be secured in top
right corner for unit to function.
8. Open the carton containing the lamp and remove the foam packaging.
9. Loosen the three screws around lamp retaining ring.
10. Turn ring to left and remove from back plate.
11. Insert the end of the lamp with the 4 pins through the side of the retaining ring where the rubber grommet is visible.
12. Seat lamp firmly into the retaining ring. Lamp will not move.
13. Insert lamp through the hole in back plate and then into the plenum.
14. Push retainer ring back onto the 3 set screws and turn right to lock lamp in place.
15. Tighten the 3 screws on retaining ring. Do not over tighten.
16. Connect the ceramic white plug onto the lamp pins. The plug is designed so that it can only be installed one way. If the pins
are not lined up with the holes, rotate the socket 90 degrees.
17. Replace cover by lining up the three guides in control box cover and slide into place. Tighten the two screws on the sides.
**IMPORTANT WIRING INSTRUCTIONS** FOR 110 VOLT. See Figure B. below
.
1. Connect the two terminals from the Saber Genius to the two outer terminals on the 110V transformer (terminals are titled
“AC” on the transformer). It does not matter which lead is tied to which of the two outer terminals on the transformer.
2. The transformer can now be plugged into a standard110-volt receptacle.
3. The purifier can now be turned on by pressing the 'ON' button
For 110V: Connect the Saber GENIUS
wire-set to the two outer terminals
on the 110V transformer
AC
GRD
AC
1
10
V r s
T
a
n o m
f
r
e
Figure B.
r
*NOTE:
Evaporator Coil*
UV exposure is dangerous to eyes, skin and
exposed plastics and rubber.
*NOTE:
**IMPORTANT WIRING INSTRUCTIONS** FOR 24 VOLT
1. Connect the two terminals from the Saber Genius to a 24 volt connection on the equipment.
2. The purifier can now be turned on by pressing the 'ON' button
Evaporator Coil*
UV exposure is dangerous to eyes, skin and
exposed plastics and rubber.
Loading...