Sanuvox B30X User Manual
patented technology
SANUVOX
scientifically proven
controls pollutants
easy installation
cost effective
mold - bacteria - viruses - smoke - odors
ULTRAVIOLET AIR PURIFIERS
Sanuvox CoilClean B30X UV Air Purifier / CoilCleaner
The Sanuvox B30X UV Air Purifier / CoilCleaner is designed for easy after market installation on Bard Wall Mount HVAC Units.
The B30X UV Air Purifier / CoilCleaner uses UV-C and UV-V Energy to destroy bio-chemical contaminants such as mold, mildew,
fungus spores, formaldehyde, solvents and secondhand smoke. The B30X will also irradiate viruses and bacteria such as
legionella, tuberculosis and meningitis to name a few.
The patented Parabolic Reflector / Shield uses the full 360 degrees of UV Light to eradicate contaminants in the air and on the
coil while protecting plastics and people from the UV exposure.
“RETROFIT THOSE BARD WALL MOUNT HVAC UNITS ALREADY INSTALLED”
EASY AFTER MARKET INSTALLATION
TREATS THE AIR AND DESTROYS MOLD ON THE COIL
ERADICATES VIRUSES SUCH AS MENINGITIS
DESTROYS CHEMICAL CONTAMINANTS
PATENTED PARABOLIC REFLECTOR INCREASES INTENSITY
PROTECTS MOTOR WINDINGS FROM UV EXPOSURE
SHIELDS EYES FROM UV EXPOSURE
SANUVOX QUALITY & PERFORMANCE
Parabolic Reflector - Shield
FEATURES
30” Hi-Intensity 19mm. Quartz Glass
UVC Germicidal Lamp
SANUVOX
30” Hi-Intensity 19mm. Quartz Glass
UVC/V Germicidal / Oxidizing Split Lamp
rF
o
OU
L
AL M
TH
A D
B R W
A full line of Residential & Commercial UV Air Purifiers are available. 1-888-SANUVOX www.sanuvox.com
C
A
V
N S
U
I
T
N
Warranty: UV Lamp 12 000 operating hours.
All other parts 5 years.
PURIFYING AIR AT THE OF LIGHT
Parabolic Reflector - Shield
SPEED
220 Volt
Safety Cut-Off
SANUVOX
INSIDE
TM
SUV - B30X
patented technology
SANUVOX
scientifically proven
controls pollutants
easy installation
cost effective
ULTRAVIOLET AIR PURIFIERS
mold - bacteria - viruses - smoke - odors
Sanuvox CoilClean B30X UV Air Purifier / CoilCleaner
Disconnect power and remove the 3 Rear Panels.
Line up purifier so that the attachment holes on the purifier
frame line up with the holes on the rail of the Bard.
Use sheet metal screws to attach the purifier to the Bard unit
at the attachment holes and to hold the Center Brace.
Center Brace
Route the cable into the electrical box on the side
of the Bard Unit.
220V connection
from Butt Connector
Cable from UV Purifier
Wrap the foam insulation above the rail with
aluminum foil to protect the foam.
The electrical connections are made to the Blower assembly as follows:
Connect a jumper wire with a spade terminal attached to the 220 Volt terminal Cable from UV Purifier.
220 Volt connection from Butt Connector.
Connect the Green ground wire of the cable to the ground lug terminal on the Bard Unit.
Install a spade terminal on the Black wire and connect.
Connect the white wire to the white wire of the cable using a butt connector.
To 220V Terminal
Cable
Butt Connector
220 Volt Terminal
Ground Lug
Ground Wire
Cover the plastic drain hose with
aluminum foil. Make sure that the drain
functions properly. Replace Rear covers
on the Bard unit.
Apply power.
Make sure the cut-off switch
is free and is not obstructed.
When the Bard blower starts, you will see
the glow from the front of the Coil.
A full line of Residential & Commercial UV Air Purifiers are available. 1-888-SANUVOX www.sanuvox.com
SUV - B30X
Loading...