Page 1
WMS2
OPT
(6901-100149 <01>)
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
Thank you for choosing the Sanus WMS2 speaker mount. The Sanus WMS2 speaker mount is designed to support a
speaker sized up to 30 cm (12 in.) deep and weighing up to 6.5 kg (15 lbs).
CAUTION
Do not use this product for any purpose not explicitly specied by Sanus Systems. Improper assembly may cause
property damage or personal injury. If you do not understand these directions, or have doubts about the safety
of the assembly, contact Customer Service or call a qualied contractor. Sanus Systems is not responsible for
damage or injury caused by incorrect assembly or use.
CAUTION
This product is designed for use in wood stud walls only! The wall must be capable of supporting up to ve times
the weight of the speaker and mount combined. If you have any doubts about the ability of the wall to support
the speaker, contact Sanus Customer Service, or a qualied contractor.
WARNING
This product contains small items that could be a choking hazard if swallowed. Keep these items away
from young children!
Hardware and procedures for multiple mounting configurations are included. When you see this symbol,
choose the correct configuration to suit your needs. Not all hardware included will be used.
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA
Customer Service: 1-800-359-5520 • 651-484-7988
info@sanus.com • www.sanus.com
©2008 Milestone AV Technologies
Page 2
3/8-16
M5 x 10mm M5 x 6mm
M5
3/8-16
M5 x 10mm M5 x 6mm
M5 x 10mm M5 x 6mm
M6 x 30mm
1/4 x 2.375 in.
3/8-16
M5 x 10mm M5 x 6mm
M6 x 30mm
M5
1/4 x 2.375 in.
3/8-16
M5 x 10mm M5 x 6mm
M6 x 30mm
3/8-16 x 3.5 in.
3/16 in.
Supplied Parts and Hardware
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item
to your dealer; contact Customer Service. Never use damaged parts!
[01] x 2
[06] x 1
[02] x 2
[03] x 2
[07] x 2
[04] x 2
[05] x 2
[08] x 2
[11] x 4
[09] x 8
[12] x 2
[13] x 2
[14] x 6
[10] x 2
[15] x 2
[16] x 1
6901-100149 <01>
Page 3
1: Attach Plate to Wall
001550.eps
3/16 in.
< 16 mm
(5/8 in.)
[09]
6901-100149 <01>
60 mm
(2.375 in.)
[01]
NOTE
Do not overtighten the lag bolts [09].
Tighten only until the plate [01] is
pulled rmly against the wall.
Page 4
2: Install Pivot
2x
[03]
[10]
[12]
[16]
[05]
3: Install Arm
2x
[14]
[11]
[15]
[11]
[14]
6901-100149 <01>
Page 5
2x
4: Install Cover
[02]
[16]
5: Install Foot and Extension
2x
[04]
[07]
6901-100149 <01>
[13]
[14]
Page 6
6: Install Foam Strips and Cap
[15]
[08]
20 x 130 mm
(3/4 x 5-1/8 in.)
7: Mount Speaker
2x
2x
Milestone AV Technologies, Inc. and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However,
Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in
connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy,
completeness or sufficiency of the information contained in this document.
6901-100149 <01>
Loading...