Sanus Systems VMPL250 International Assembly Instructions [ml]
FRANÇAIS
Customer Service Europe: 31 (0)20 5708938 • fax 31 (0)20 5708989
See complementary Sanus products at www.sanus.com
International Assembly Instructions for model VMPL250
ENGLISH
ESPAÑOL
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 (6901-300069 <01>)
PYCCKO
Assembly Instructions for Model: VMPL250
Thank you for choosing a Sanus Systems Vision Mount Wall Mount. This product is designed to mount flat panel televisions weighing up to 130 lbs.
only 1.25” off of the wall.
Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or
contact Sanus at 800.359.5520 or www.sanus.com. We can quickly assist you with installation questions and missing or damaged parts. Replacement
parts for Sanus products purchased through authorized dealers will be shipped directly to you. Check carefully to make sure there are no missing or
defective parts. Never use defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or
incorrect use.
Note: The supplied wall mounting hardware is not for steel stud walls or old cinder block walls. If you are uncertain about the nature of your wall,
consult an installation contractor. Sanus makes every effort to assure all necessary television mounting hardware is included. If the hardware you need
is not included please consult your local hardware store or call Sanus Systems.
Required Tools: 3/16 drill bit, 1/2” Masonry Bit for brick concrete or concrete block installations, wrench or socket set, Phillips screw driver.
Supplied Parts: *Not shown as actual size
ENGLISH
(1) Wall Plate - a* (1) Safety Bar - b* (2) Monitor Bracket - c*
(4) M4 x 12 Bolt - d (4) M5 x 12 Bolt - e (4) M6 x 12 Bolt - f (4) M8 x 16 Bolt - g
(4) M4 x 30 Bolt - h (4) M5 x 30 Bolt - i (4) M6 x 35 Bolt - j (4) M8 x 40 Bolt - k
(4) M4 Lock Washer - l (4) M5 Lock Washer - m (4) M6 Lock Washer - n (4) M8 Lock Washer - o
(4) M4/M5 Spacer - p (4) M6/M8 Spacer - q (8) M4/M5 Washer - r (4) M6/M8 Washer - s
(6) Lag Bolt - t (6) Lag Bolt Washer - u (6) Concrete Anchor - v
Step 1: Mount Low Prole Monitor Brackets to a television with a at back
Note: For televisions with a curved back, or an obstruction near the threaded insert see Step 2.
First, determine the diameter of the Bolt (d,e,f,g) your TV requires by hand threading them into the threaded insert on the back of the TV.
If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below.
You will thread the Bolt through the appropriate Lock Washer (l,m,n,o), the corresponding Washer (r,s), the Monitor Bracket (c), and finally into the TV. Make sure the Monitor Brackets are vertically centered and level with each other. See the appropriate Diagram below.
ENGLISH
M4 Diameter Bolt M6 Diameter Bolt
c c
d f
l n
r s
Diagram 1
M5 Diameter Bolt M8 Diameter Bolt
c c
e g
m o
r s
Note: After completing Step 1, proceed to Step 3.
Step 2: Mount Low Prole Monitor Brackets to a television with a curved back or an obstruction near the threaded insert
First, determine the diameter of the Bolt (h,i,j,k) your TV requires by hand threading them into the threaded insert on the back of the
TV. If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram
below. You will thread the Bolt through the appropriate Lock Washer (l,m,n,o), the corresponding Washer (r,s), the Monitor Bracket
(c), a Spacer (p,q), a second Washer (r - M4/M5 diameters only) and finally into the TV. Make sure the Monitor Brackets are vertically
centered and level with each other. See the appropriate Diagram below.
M4 Diameter Bolt M6 Diameter Bolt
j
h n
l s
r
c c
r
p q
ENGLISH
Diagram 2
M5 Diameter Bolt M8 Diameter Bolt
i k
m o
r s
c c
r
p q
Loading...