Sanus Systems CFAR47 User Manual

Assembly Instructions for Model: CFAR47

Thank you for choosing the Component Furniture line from Sanus Systems! Use

this manual to congure the CFAR47 as shown on the right. The CFAR47 is de­signed to hold a LCD, Plasma or DLP TV.

Safety Warning: If you do not understand these directions, or have any doubts
about the safety of the installation, please call a qualied contractor or contact Sa­nus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there
are no missing or defective parts. Our customer service representatives can quickly
assist you with installation questions and missing or damaged parts. Replacement
parts for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper installation may cause damage or serious
injury. Do not use this product for any purpose that is not explicitly specied by
Sanus Systems. Sanus Systems can not be liable for damage or injury caused by
incorrect assembly, or incorrect use. Please call Sanus Systems before returning
products to the point of purchase.

Required Tools: Drill, 3/16” drill bit, phillips screw driver, at head screw driv­er, crescent wrench, tape measure.

Supplied Parts and Hardware: Hardware shown at actual size. Some
parts may come pre-assembled**

(4) Carpet Spike - a (12) Cam Pin - b (8) Spacer - c (8) Back Panel Bolt - d

(2) Phillips Pan Head Bolt - e (4) Dowel - f (4) Glass Shelf Pin - g (8) Wood Shelf Pin - h

(4) Wood Screw - i (4) Knob Bolt - j** (8) Hinge Plate Screw - k** (16) Hinge Screw - l

(2) Tip Protector Bolt - m (2) Stop Nut - n (8) Hinge Car Bolt - o

(2) Lag Bolt - p (2) Lag Bolt Washer - q (1) Allen Key - r

Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113 10.10.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Parts: Not all parts shown at the same scale

(1) Shelf Retainer - u (1) Shelf Bracket - v (4) Small Door Hinge - w
(4) Foot - s (4) Door Knob - t

**

(4) Hinge Plate - x** (4) Bi-fold Hinge - y (4) Hinge Car - z (2) Furniture Bracket - aa (2) Wall Bracket - bb

(3) Front Rail - cc (3) Back Rail - dd

(2) Door - hh
(2) Bi-fold Door - gg

(2) Side Panel - ee (2) Back Panel - ff

(1) Top - ii

(1) Glass Shelf - jj (2) Wood Shelf - kk

Step 1: Add Wood Shelf Pins and Feet to Side Panels

Insert a Wood Shelf Pin (h) into the holes adjacent to the two lower sets of cams in each Side Panel (ee). See Detailed View A of Diagram
1 for assistance.

Add a Foot (s) to each pillar of the Side Panel (ee). If you wish to install the Carpet Spikes (a), thread each Carpet Spike into the Foot.
You can adjust the height of the Carpet Spikes with the Nut. See Detailed View B of Diagram 1 for assistance.

Warning: The ends of the carpet spikes are very sharp and may scratch oors or furniture. All sharp objects can be

hazardous to children. For this reason we provide the carpet spikes as an option. Sanus Systems will not be liable

for damage or injury.

Detailed View A

Diagram 1

ee

h

Detailed View B

s

a

Step 2: Add Front and Back Rails

Add Front Rails - Attach the Front Rail (cc) to the Side Panel Assembly (ee) by sliding the clamp down the groove in each Side Panel

pillar as shown in the Top View of Diagram 2. Make sure the smooth side of the Front Rail is facing outward and the open channel faces
down as seen in the Detailed View below on the right. Once the Front Rail is positioned at the bottom of the groove and resting on the
Foot (s), tighten the allen bolt on the back side of the Front Rail so the clamp widens to hold the Front Rail rmly in place. Repeat pro­cess for the second Front Rail, making sure it is below the upper Wood Shelf Pins (h).

Add Back Rails - To attach the Cam Pins (b) to the Back Rail (dd), make sure the arrow on each Cam is facing the hole in the outside
of the Back Rail and add two Cam Pins to each end of the Back Rail as shown in Diagram 2. Make sure there is a small space between
the head of the pin and the Back Rail as seen in the Detailed View on the right.

Attach the Back Rail by sliding the cam pins down the groove on the Side Panel pillar as shown in the Top View of Diagram 2. Make
sure the Back Rails are oriented so the threaded holes in the center are on the top, and the Cams face inside the cabinet. Once the bottom
Back Rail is resting on the Foot (s), tighten the cams labeled in Diagram 2 to hold it in place. Slide the other Back Rail down the groove
in the pillar in the same manner until it just below the upper Wood Shelf Pins (h). Tighten the cams in a clockwise direction to hold the
back rail in place.

Note: The second Front and Back Rails will need to be adjusted once the upper Wood Shelf is in place.

Detailed View

Top View (Back Rail)
Back Left Corner b

Diagram 2

cams
b

Detailed View
dd

clamp

Top View (Front Rail) open
Front Left Corner channel

allen bolt

clamp
cc