Sanus SFC18, SFC22 User Manual
4] The Steel Foundations center channel stand has included a pair of adjustablestuds(j)and1/4"rubberstud covers (k). These are for use if you require your speaker to angle upwards. Thread the adjustable stud through the top plate with the allen wrench to the desired height. Using a machine nut, lockthethreadedstudintoplace.Photo 5 - Thread the rubber stud covers over the top of the adjustable stud to protect
your speaker from being scratched. Three Neoprene Isolation pads shouldbeplacedattherearofthetopplatebetweenthetopplateandthe speaker to ensure the speaker does not slide off the back of the stand.
*NOTE:Theendsofthespikedfeetand steel speaker studs are very sharp and mayscratchfloorsorfurniture.Allsharp objects can be hazardous to children. For this reason large rubber feet and rubber isolation pads are provided as an option. Sanus Systems will not be liable for damage or injury.
Photo 5
Every effort has been made to ensure that your stands are perfect. If you have any questions or feel that there is a problem of any kind, please call our CustomerAssistance number. We can assist with questions or damaged/
Sanus Systems 2221 Highway 36 W St. Paul MN |
55113 11.22.04 |
800.359.5520 www.sanus.com |
|
Page 4 |
Page 1 |
STEEL FOUNDATIONS® SFC INSTRUCTION MANUAL
ʻTake the time to find the right speaker locations for your listening room.ʼ
PHOTO 1
a
f
g
e
i
Important:Thisproductusestwo differentfeetforeachbase.Before installing,besuretocheckthatthe feet are mounted with the (1) foot on the front left and rear right of the base, (2) front right and rear left. The designation (1) & (2) are on the bottom of each foot.
d
hb
k
jc
1] Attach the plastic feet (e) to the corners of the base with the small pan headbolts(f).Photo2-Grouptwopillars withthebase.Aligntheholesinthebase withtheholesintheisolationblock(a). Bolt the pillars and the base together with the isolation block between them
using the large pan head bolts |
(b) and |
lock washers (c). Photo 3-Using the |
|
wire guide is optional. |
Photo 2 |
n |
|
|
2] Adhere the two inch self-adhesive damping washers (l) to the flush |
|
|
|
side of each top plate. The damping washers will be set in between the |
|
|
m |
top plate and the pillars. (Optional: You may fill the pillars with sand |
|
l |
or shot at this time.)Align the holes in the top plate with corresponding |
|
|
|
holesinthetopofeachpillar.Boltthe pillarsandthetopplatetogether |
|
|
|
|
using the flat head bolts(n). Photo 4-The wire guide (m) is optional. |
Hardware List |
|
3] Both spiked feet (g) and rubber feet (d) are provided for your Steel |
|
(PHOTO 1) |
|
||
a) |
isolation block - 1 |
|
Foundations®.The spiked feet are preferable in terms of performance. |
b) |
1-1/2" pan head bolt - 2 |
|
Thread a machine nut (h) over the |
c) |
lock washer - 2 |
|
spiked feet and thread the ends of the |
d) |
rubber isolation pad - 8 |
|
spikedfeetintothethreadedinsertsin |
e) |
plastic foot - 4 |
|
|
|
the corner feet.Adjust the spiked feet |
||
f) |
5/8" pan head bolt - 4 |
|
|
g) |
carpet spike - 4 |
|
until the stand is level and then lock |
h) |
machine nut - 8 |
|
into place by tightening the machine |
i) |
allen key - 1 |
|
nut.Useofthespikedfeetisoptional.* |
j) |
threaded stud - 2 |
|
The rubber feet are provided as an |
k) |
rubber stud cover - 2 |
|
alternative. |
l) |
cork damping washer - 2 |
|
|
|
|
||
m) |
wire guide - 2 |
|
|
n) |
flat head bolt - 2 |
|
Photo 3 |
|
|
|
|
Page 2 |
Page 3 * PLEASE READ THE NOTE ON PAGE 4 OF THIS MANUAL! |
Loading...