Assembly Instructions for Platinum Furniture Model: PFFP Shelf & PFFP2 Shelf
Thank you for choosing a Sanus Systems Platinum Furniture Model: PFFP Shelf and PFFP2 Shelf.
WARNING: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualied
contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective
parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement
parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper installation
may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied by Sanus Systems. Sanus
Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus
Systems before returning products to the point of purchase.
Required Tools: 3/16” Allen Key
Supplied Parts and Hardware: (All threaded fasteners are shown full size.)
Large Glass Shelf - A
Qty. 1
Glass Shelf Washer - B
M8 Allen Bolt - F
Qty. 2
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Qty. 1
1/4 - 20 Allen Bolt - G
Qty. 2
Shelf Bracket - C
Qty. 1
M8 Washer - H
Qty. 2
Shelf Plate - D
Qty. 1
Spring Washer - I
Qty. 2
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 03.07.06 (100029)
Shelf Bracket Cap - E
Qty. 1
Plastic Washer - J
Qty. 2
Step 1: Remove Top Cap and Wall bracket from Pillar
NOTE: This Step is required only if you have already assembled your PFFP or PFFP2.
Remove the Top Cap from the Pillar as shown in Diagram 1A.
Loosen the two M8 Allen Bolts; then, slide the Wall bracket Assembly up and out of the Pillar as shown in Diagram 1B
Diagram 1A Diagram 1B
Wall Bracket
Assembly
Pillar
Top Cap
Pillar
M8 Allen
Bolt
Step 2: Remove Small Glass Shelf
NOTE: This Step is required only if you have already assembled your PFFP2.
Remove the Shelf Bracket Cap as shown in Diagram 2.
Loosen the two M8 Allen Bolts; then, slide the Small Glass Shelf up and out of the
Pillar as shown in Diagram 2
Step 3: Shelf Bracket assembly
Thread two M8 Allen Bolts (F) through a Spring Washer (I), a M8 Washer (H), the
Shelf Bracket (C), and into the Shelf Plate (D) as shown in Diagram 3.
Using the Allen Key, screw the two M8 Allen Bolts (F) into a Shelf Plate (D) until
there is a gap of 1/8” between the Shelf Bracket (D) and the Shelf Plate as shown
in Diagram 3.
Shelf Bracket
Cap
Small Glass
Shelf
H
I
F
Diagram 2
M8 Allen
Bolt
Pillar
Diagram 3
D
C
Step 4: Add Shelf Bracket to Pillar
Insert the Shelf Bracket Assemblies into the Pillar by sliding it down from the top of the Pillar, making sure the Shelf Plate (D) ts into the
channel in the Pillar as shown in Diagrams 4A and 4B.
Once the Shelf Bracket Assembly is in place, use the Allen Key to tighten the M8 Allen Bolts (F), securing the Shelf Bracket Assembly in
place.
NOTE: If you have a PFFP2, the Small Glass Shelf removed in Step 2 may be re-installed at this time, following the above
procedure.
Diagram 4A Diagram 4B
D
Shelf Bracket
Assembly
Pillar
Pillar
Step 5: Add Glass Shelf
Slide a Glass Shelf Washer (B) onto the Glass Shelf (A), making sure the holes
in the Glass Shelf Washer align with the holes in the Glass Shelf as shown in
Diagram 5.
Slide the Glass Shelf (A) and Glass Shelf Washer (B) into the Shelf Bracket (C);
then, thread the two 1/4-20 Allen Bolts (G) through the Plastic Washers (J), the
Glass Shelf (A) and into the Shelf Bracket Assembly (C) as shown in Diagram 5.
Tighten the 1/4-20 Allen Bolt (G).
F
D
Diagram 5
G
J
A
C
B
C
Step 6: Install Shelf Bracket Cap
Slide the Shelf Bracket Cap (E) removed in Step 2 and the new Shelf Bracket
Cap (E) over the Shelf Brackets so that they hide the M8 Allen Bolts as shown
in Diagram 6
Shelf Bracket
Cap (E)
Diagram 6
M8 Allen
Bolt
Pillar
Step 7: Add Wall Bracket to Pillar
Insert the Wall Bracket Assembly into the Pillar by sliding it down from the top of the Pillar, making sure the Wall Plate ts into the channel
in the Pillar as shown in Diagrams 7A and 7B.
Once the Wall Bracket Assembly is in place, use the Allen Key to tighten the M8 Allen Bolt, securing the Wall Bracket Assembly in
place.
Slide the Wall Bracket Spacers into place on each side of the Pillar between the Pillar and Wall Bracket, until the tab on the Wall Bracket
Spacer snaps into one of the slotted holes in the Wall Bracket. If necessary, loosen the M8 Allen Bolt to allow sufcient space between
the Wall Bracket and the Pillar to install the Wall Bracket Spacer as shown in Diagram 7B
Diagram 7A Diagram 7B
Wall Bracket
Assembly
Wall Bracket
Spacer
Pillar
Pillar
Step 8: Install Top Cap
Align the two pegs on the bottom of the Top Cap with the
corresponding pattern in the top of the Pillar; then, press the Top
Cap onto the Pillar as shown in Diagram 8.
Wall Bracket
Assembly
M8 Allen
Bolt
Diagram 8
Pillar
Top Cap
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 03.07.06 (100029)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Loading...