Page 1
Assembly Instructions for Natural Furniture, Model: NF204
Thank you for choosing the Natural Furniture line from Sanus Systems. If you have any questions
regarding this or any other Sanus Systems product, contact us at 800.359.5520 or visit us at
www.sanus.com. Our customer service representatives will assist you with any issues regarding
assembly or missing parts. Check to make sure none of the parts are missing or defective. Never
use defective parts. Replacement parts for products purchased from an authorized dealer will be
shipped directly to you. Please call Sanus Systems before returning products to retail stores.
Supplied Parts and Hardware: (Threaded are fasteners shown full size)
Front Frame - A
Qty. 1
Wire Strap - H
Qty. 2
Rear Frame - B
Qty. 1
Three Hole Plate - I
Qty. 4
Plastic Wire Cover - C
Qty. 1
Allen Bolt - J
Qty. 8
Glass Top Shelf - D
Qty. 1
Cross Tube - F
Qty. 6
Glass Mid Shelf - E
Qty. 3
Cross Tube W/ Stud - G
Qty. 2
Decorative Face Bolt - K
Qty. 6
1 in. Washer - L
Qty. 4
Glass Protector - N
Qty. 4
1.5 in. Washer - M
Qty. 4
Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113 04.11.06 (100041)
Customer Service 800.359.5520 See complementary Sanus products at www.sanus.com
Allen Key - O
Qty. 1
Page 2
Step 1: Attach Cross Tubes to Front Frame
NOTE: For ease of assembly, lay the Front Fame face down on a soft at surface after inserting the six Decorative
Face Bolts.
Insert six Decorative Face Bolts (K) through the Front Frame (A). Slide a Three Hole Plate (I) over the Decorative Face
Bolts; then, screw a Cross Tube (F) onto each Decorative Face Bolt. Firmly hand tighten each Cross Tube.
Diagram 1
I
A
F
K
Step 2: Attach Cross Tubes W/Stud to Front Frame
Place a 1” Washer (L) on the threaded stud of each Cross tube W/Stud (G) and screw them into the Front Frame (A). Firmly
hand tighten each Cross Tube W/Stud.
Diagram 2
A
L
G
Page 3
Step 3: Attach Rear Frame to Front Frame and Cross Tubes
With The Cross Tubes (F,G) still facing up, and the Front Frame (A) still on a soft, at surface, place a 1” Washer (L) on each
Cross tube W/Stud (G) and a Three Hole Plate (I) on the remaining Cross Tubes (F).
NOTE: Horizontal grooves in the Rear Frame must be facing the Front Frame and the three holes closest to the
edge of the Rear Frame must be aligned toward the top of the Front Frame.
Align the holes in the Rear Frame (B) with the holes in the Cross Tubes; then, using a 1.5” Washer (M) and Allen
Bolt (J), secure the Rear Frame to the Cross Tubes (F) using the Allen Key (O).
Using 1.5” Washer (M) and Allen Bolt (J), secure the Rear Frames to the two center Cross Tubes W/Studs (G) using the Allen
Key (O).
Using Allen Bolts (J) and Allen Key (O), secure the two Wire Straps (H) to the Rear Frame.
Diagram 3
Three holes near
edge toward top.
I
M
Horizontal
Groove
F
J
H
J
G
L
M
J
M
J
F
I
B
H
J
Page 4
Step 4: Glass Mid Shelf Installation
NOTE: Make sure the round edges of the Glass Shelves are to the sides and the at edge ts into the groove in the
Front and Rear Frame.
Slide each Glass Mid Shelf (E) through the front of the Front Frame (A) until it is fully into the groove in the Rear Frame (B);
then, lower it onto the ledge on the back side of the Front Frame.
Diagram 4
A
B
E
Step 5: Glass Top Shelf Installation
Place two Glass Protectors (N) in each corner of the top of
the Front Frame (A) and two on the Rear Frame (B); then
place the Top Glass Shelf (D) on the Glass Protectors on the
Front and Rear Frames.
Diagram 5
D
N
N
B
A
Step 6: Plastic Wire Cover Installation
After the desired components have been placed on the Glass Shelves (D & E) and the cables routed through the Wire Straps
(H), install the Plastic Wire Cover (C) by inserting one side into a groove in the back of the Rear Frame (B); then, snapping the
other side of the Plastic Wire Cover into the grove on the other side of the Rear Frame as shown in the Top View.
Diagram 6
Top View
Plastic Wire
Cover (C)
C
H
B
Grooves in
Rear Frame (B)
Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113 04.11.06 (000041)
Customer Service 800.359.5520 See complementary Sanus products at www.sanus.com
Loading...