Sanus F42OA, F50A, F42A, F32OA, F50OA User Manual

...

I N S T A L L A T I O N I N S T R U C T I O N S

Decorative Display Frame and

Optical Filter Kit

32", 42", and 50"

Installation Instructions

DISCLAIMER

CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

IMPORTANT WARNINGS AND CAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: IMPROPER INSTALLATION CAN LEAD TO ACCESSORY OR DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the combined weight of all components attached to display does not exceed the weight capacity of the display mount!

INTRODUCTION

TOOLS REQUIRED FOR INSTALLATION

•No tools are required for this installation

INSPECT MOUNT BEFORE ASSEMBLY

Carefully inspect mount assembly for shipping damage (see Figure 1). If damage is apparent, call your carrier claims agent and do not continue with installation until the carrier has reviewed the damage.

NOTE: Thoroughly read and understand all assembly instructions before starting installation.

Table 1: PARTS

ITEM	DESCRIPTION	QTY.
10	FRAME, Decorative Display	1

20	INSTRUCTIONS, Installation	1

30	LENS, Optical (when ordered sepreately)	1

WARNING: USING IMPROPER HARDWARE CAN LEAD TO MOUNT AND/OR DISPLAY FALLING. Use only hardware provided with mount. DO NOT substitute!

Installation Instructions

32", 42", and 50"

For the frame to properly fit it must completely cover the bezel on the display.

Use the figure below and the Display Compatability Tables on page 4 to determine if frame will work with display.

The frame will fit the display if the top, side and bottom bezels on display all measure less than 4 ½" (114mm).

To make sure frame fits display:

1.Measure width of upper bezel on display.

2.Measure the distance from the top of display to the inside of the upper bezel (Edge of screen).

3.Record measurement.

4.Measure width of side bezels on display.

5.Measure the distance from the right or left of display to the inside of the right or left bezel (edge of screen).

NOTE: Right and left bezels should be the same so only one side needs to be measured.

6.Record measurement.

NOTE: The left and right side bezels will be the same width so you only have to do this on one side of your TV.

7.Measure the width of lower bezel on display.

8.Measure the distance from the bottom of display to the inside of the bottom bezel (edge of screen).

9.Record measurement.

NOTE: Depending on the brand and model of display, this measurement may or may not be the same as the width of the upper bezel.

Step 1

Step 2

Step 3

Figure 1

Display Size Compatability Tables

TELEVISIONS MAXIMUM ALLOWABLE DIMENSIONS

Diagonal Dim.	Height (inches / mm)		Width (inches / mm)

32	23	31/32 (609mm)	37 3/32 (942mm)

42	28	57/64 (734mm)	45	13/16 (1164mm)

50	32	27/32 (834mm)	52	25/32 (1341mm)

+ 5 hidden pages