Page 1
Assembly Instructions for Model: CFA56
Thank you for choosing Sanus Systems Component Furniture. Please check carefully to make sure there are no missing or defective
parts. Never use defective parts. Improper assembly may cause damage or serious injury. If you have any questions regarding this product, contact Sanus at 800.359.5520 or visit www.sanus.com. Our customer service representatives can quickly assist you with missing or
damaged parts. Replacement parts for Sanus products purchased through authorized dealers can be shipped directly to you. Please call
Sanus Systems before returning products to the point of purchase.
REQUIRED TOOLS: Phillips Screw Driver, Hammer
Check Carefully to ensure there are no missing Parts or Hardware before beginning the installation.
HARDWARE: (shown at actual size)
(4) Carpet Spike Assembly - a (8) Cam Pin - b (4) Dowel - c (4) Back Panel Bolt - d
(4) Spacer - e (4) Bottom Shelf Pin - f (12) Shelf Pin - g (1) Knob Bolt - h
(1) Knob - i (6) Hinge Screw - j (6) Hinge Plate Screw - k
(4) Isolation Pad - l (4) Isolation Shelf Pin - m (1) Allen Key - n
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 9.29.05
Page 2
Parts: *Some Parts not shown at same scale
(4) Foot - o* (3) Hinge Plate - p* (3) Hinge - q*
(2) Front Rail - r (2) Back Rail - s
(2) Side Panel - t* (1) Back Panel - u* (1) Door - v*
(1) Top - w (3) Glass Shelf - x
(1) Isolation Shelf - y (1) Bottom Shelf - z
Page 3
Step 1: Add feet
Add a Foot (o) to each pillar of each Side Panel Assembly (t) as shown in Diagram 1. If you wish to install the Carpet Spikes (a), thread
each Carpet Spike into the foot as seen in Diagram 1. You can adjust the height of the Carpet Spikes with the Nut shown in the Detailed
View of Diagram 1.
Warning: The ends of the carpet spikes are sharp and may scratch oors or furniture. All sharp objects can be hazardous to
children. For this reason we provide the carpet spikes as an option. Sanus Systems will not be liable for damage or injury.
Diagram 1 Detailed View
t
o
a
Step 2: Attach the Front Rails to the Side Panel Assembly
Attach the Front Rail (r) to the Side Panel Assembly (t) by sliding the clamp down the groove in the Side Panel pillar as shown in the Top
View A of Diagram 2. Make sure the at smooth side of the Front Rail is facing outward, as shown in Diagram 2. Once the Front Rail is
positioned at the bottom of the groove and resting on the Foot (m), tighten the allen bolt on the back side of the Front Rail so the clamp
widens to hold the Front Rail rmly in place. Repeat process for the other Front Rail, making sure it is level with the corner pillar.
Top View A Diagram 2
(Front Left Corner)
t allen bolt
clamp
r
Page 4
Step 3: Add second Side Panel Assembly
Attach the second Side Panel Assembly (t) by lining up and inserting both Front Rails (r) into the groove in the corner pillar. If the clamp
on the Front Rail will not t in the groove, make sure the allen bolt (labeled in the Top View) is loose so the clamps are close together.
Once you have the Front Rails aligned so the bottom one is resting on the Foot (o), and the top one is level with the corner pillar, tighten
the allen bolt in the back of the Front Rail to widen the clamp to secure it to the pillar. See the Top View of Diagram 3 for assistance.
Top View
(Front Right Corner) Diagram 3
allen bolt t
r clamp
Step 4: Attach the Back Rails
Attach the Cam Pins (b) to the Back Rail (s). Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail and add
two Cam Pins to each end of the Back Rail as shown in the Detailed View of Diagram 4. Insert the Cam Pins until there is a small space
between the head of the pin and the Back Rail.
Attach the Back Rail by sliding the cam pins down the groove on the Side Panel pillar as shown in the Top View of Diagram 4. Once the
Back Rail is resting on the Foot (o), tighten the cams labeled in Diagram 4 to hold it in place. Make sure the bottom Back Rail is oriented
so the threaded holes near the ends are on the top, and the Cams face inside the cabinet, as seen in Diagram 4. Make sure the top Back
Rail is oriented so the threaded holes near the ends are on the bottom, and the Cams face inside the cabinet, as seen in Diagram 4
Diagram 4
Top View
Detailed View (Back Left Corner)
s
cam
b
t b
s
Page 5
Step 5: Add the Back Panel
Insert a Back Panel Bolt (d) through the Back Panel (u), a Spacer (e) and thread it into the Back Rail (s) as seen in the Detailed View of
Diagram 5. Repeat the process until all 4 Back Panel Bolts are attached to the Back Rails. Proceed to tighten the Back Panel Bolts.
Diagram 5
Detailed View
s
e
d
u
Step 6: Add Isolation Pads to Isolation Shelf
Add an Isolation Pad (l) to each hole in the Isolation Shelf (y) by peeling off the adhesive cover from the soft side of the Isolation Pad
as shown in the Detailed View of Diagram 6. Make sure the soft side of the Isolation Pad is facing toward the shelf when inserting it
into the Isolation Shelf.
Detailed View
Diagram 6
y
l
Page 6
Step 7: Add Shelves
Add 4 Shelf Pins (g) for the Isolation Shelf (y) at the desired height as shown in Detailed View A of Diagram 7. Next, align the holes on
the bottom side of the Isolation Shelf with the Shelf pins, and proceed to place the shelf on the Shelf Pins. You can level the Isolation
Shelves by adjusting the Bolt in the Shelf Pin. The nut will hold Bolt in place.
To add the Glass Shelf (x), insert 4 Shelf Pins (g) at the desired height into the Side Panels as shown in the Detailed View B of Diagram
7. Proceed to place the Glass Shelf on the Shelf Pins.
Thread a Bottom Shelf Pin (f) into the Side Panel (t) as shown in Detailed View C of Diagram 7. Repeat process until all four Bottom
Shelf Pins have been inserted into the Side Panel. Proceed to press t the Bottom Shelf (z) so it is locked into the Bottom Shelf Pins.
Detailed View A Diagram 7
m
Detailed View B
t
t
Detailed View C
g
t
f
Step 8: Fit Top to assembly
Insert a Dowel (c) into each corner hole in the bottom side of the Top (w). Gently tap the Dowels in. Press t the Top to the assembly
so the Dowels go into the holes in the corner pillars as seen in the Detailed View of Diagram 8. Make sure the Top is ush with the
corner pillars.
Diagram 8 Detailed View
w
c
corner pillar
Page 7
Step 9: Prepare the Door
Insert a Knob Bolt (h) through the backside of the Door (v) and proceed to thread it into the Knob (i). Tighten until the Knob is ush
with the front side of the Door. See the Detailed View of Diagram 9 for assistance.
Diagram 9 Detailed View
h
i v
Step 10: Add Door Hinges
Attach the Hinge (q) to the Door (v) by threading a Hinge Screw (j) through each hole in the Hinge and into the Door. See the Detailed
View of Diagram 10 for assistance. Tighten each Hinge screw until the Hinge is secure to the Side Door. Repeat the process for the two
Hinges.
Diagram 10
Detailed View
v
j q
Page 8
Step 11: Add Door to Side Panel
Attach the Hinge Plates (p) by threading a Hinge Plate Screw (k) through each hole in the Hinge Plate and into the Side Panel as shown
in the Detailed View of Diagram 11. Repeat the process until both Hinge Plates are attached. Proceed to tighten the Hinge Plate Screws
with a phillips screw driver until tight.
To attach each Hinge (q) to its Hinge Plate, the bolt along the back center of the Hinge Plate must be loose during installation. The slot
on the end of the Hinge will t around the bolt on the Hinge Plate. The top and bottom Hinges should engage at the same time as shown
in Diagram 11. Once the two parts of the Hinge are mated, tighten the bolt on the Hinge Plate rmly with a screwdriver.
Diagram 11
Detailed View
v
p
k
t
q
Step 12: Hinge Adjustment
Each hinge Assembly is adjustable in multiple directions. See Diagram 12 for assistance.
Diagram 12
Side Adjustment Depth Adjustment Height Adjustment
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 9.29.05
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Loading...