Santec sa5port User Manual
Out to Shower Head
H
Plug in
From Control Unit
Shower Head
Out to Hand Shower
Out to Wall Tub
C
Hand Shower
SA5PORT
5-PORT VALVE INSTALLATION INSTRUCTION
Using ½” or ¾” IPS, plumb the stop valve according to the
1.
handle styles described below.
Allow 1¾” diameter hole for the valve stems.
2.
Allow a 1¼” diameter hole for the shower arm or
3.
personal shower elbow.
WARNING
Where tile construction is planned for the finished walls,
allow for the extra thickness dimensions when roughing
the valves.
TEST FOR PROPER FUNCTION BEFORE CLOSING WALLS!
4.
It may be necessary to cut off the excess stem
accordingly to the frontset dimension of the handle
styles described below. (Measurement is from the tip of
the broach to the surface of finished wall).
Apply the finish trim.
5.
FRONTSET (”F”) FROM FINISHED WALL
16-point broach 20-point broach Adapter - P0477
F
9
6
"
16
Initial length Initial length
3
5
2
" - 2
8
" - 2
8
" - 1
2
" - 2
8
" - 2
8
" - 2
8
" - 2
2
" - 2
2
" - 2
8
" - 1
4
" - 1
4
"
8
5
"
8
7
"
8
5
"
8
5
"
8
1
"
8
3
"
4
3
"
4
5
"
8
3
"
4
3
"
4
1
"
2
**
*
EN
ER
*
ET
*
EX
*
EY
EZ
JC
JZ
KC
LA
LC
LL
**
*
*
*
*
AA
AC
BR
CA
CC
CD
CN
CX
DD
EC
ED
EM
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
3
2
1
1
3
2
3
2
7
1
1
2
1
2
3
2
1
1
1
1
1" - 1
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
1
1
" - 1
4
1
1
" - 1
4
1
" - 1
1
4
1
" - 1
1
4
1
" - 1
1
4
1
2
" - 2
2
1
1
" - 1
4
1
" - 2
2
2
1
" - 2
2
2
1
2
" - 2
4
2" - 2
2" - 2
F
7"
7
3
"
4
1
"
2
3
"
4
3
"
4
3
"
4
3
"
4
1
"
2
3
"
4
3
"
4
5
"
8
1
"
4
1
"
4
LM
LV
TD
TJ
TT
TX
NL
NX
XA
XE
XL
YC
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
F =
1
8
2" - 2
3
2
4
3
2
4
2" - 2
3
2
4
1
2
" - 2
8
1
2
" - 2
8
1
2
" - 2
8
1
" - 2
2
2
3
1
4
1
2
" - 2
4
" - 2
1
" - 3
" - 3"
1
" - 3
" - 2"
1
"
8
"
4
1
"
8
"
4
1
"
8
3
"
8
3
"
8
1
"
2
3
"
4
5
"
8
Requires P0477 Adapter and 20-point broach*
Requires P0477 Adapter and 16-point broach**
last updated 06/08
SANTEC LIFETIME LIMITED WARRANTY
Finishes: Santec Polished Chrome, Polished Orobrass and Satin Nickel finishes
1.
carry a Lifetime Limited warranty against manufacturing defects and tarnish to
the original purchaser with the exclusion of kitchen drain assemblies which,
due to the nature of their use, are not warranted. Santec recommended
custom finishes carry a ten (10) years limited warranty against manufacturing
defects and tarnish to the original purchaser with the exclusion of kitchen and
pop-up drain assemblies which, due to the nature of their use, are not
warranted. Kitchen products carry a three (3) year limited warranty.
Cartridges: Santec Cartridges carry a lifetime limited warranty against manufacturing
2.
defects for the life of the product to the original purchaser.
3.
Parts: Santec parts carry a ten (10) year limited warranty against manufacturing
defects, to the original purchaser. Kitchen products carry a five (5) year limited warranty.
4.
Warranty exclusions and limitations: This warranty does not cover: damage due to
negligence, accident, abuse, improper installation, or improper maintenance such as,
but not limited to: heat from soldering during installation, the use of plumbers putty,
damage from tools used during installation, the use or exposure to chemicals or
cleaning products either abrasive or non abrasive or the use of any cleaning tool or
product other than a soft, clean cloth. This warranty does not cover: changes in the
finish or in the product due to normal wear or aging and does not cover any products
or parts which have been altered or used in a manner not typical for the product. This
warranty does not cover and Santec will not be held liable for damage to products
caused by the freight carrier and a claim should be made immediately to the freight
carrier should this occur. This warranty does not cover any cost involved in the
installation, repair, or replacement of any Santec product or part. This warranty does
not cover and Santec will not be held liable for any loss, damages, or expenses,
incidental or consequential whatsoever, originating from the purchase, installation,
use, repair, failure, or replacement of any Santec product or part, as allowed by law.
The product or components of the covered product will either be repaired, refinished
or replaced, at the sole discretion of Santec. Santec reserves the right to examine any
product claimed defective prior to any warranty claim being accepted or processed,
at its sole discretion. This warranty gives you specific legal rights and you may have
other rights which may vary from state to state.
Effective 01/01/08 - Replaces and supersedes any previously issued warranty
FINISH CARE INFORMATION
For clear coated or enamel color finishes:
We recommend that all faucets, drains, etc
be gently wiped dry with a soft cloth after use
to avoid water spotting and water deposit
buildup. A mild liquid hand soap, such as Ivory
may be used occasionally if desired. Use of
non-abrasive carnauba wax will add protection to the finish and should be used if the
faucets will not be dried after use.
For non-clear coated and specialty finishes:
We recommend that all faucets, drains, etc be
gently wiped dry with a soft cloth after use to
avoid water spotting and water deposit
buildup. Use of a non-abrasive carnauba wax
is required occasionally.
PLEASE REGISTER YOUR PRODUCT ONLINE FOR WARRANTY SERVICES
www.santecfaucet.com/registration
Loading...