Santec Modern kitchen faucet User Manual

SANTEC LIFETIME LIMITED WARRANTY
MODERN STYLE SINGLE-LEVER HANDLE
1. Finishes: Santec Polished Chrome and Polished Orobrass finishes carry a Lifetime Limited warranty against manufacturing defects and tarnish to the original purchaser with the exclusion of kitchen drain assemblies which, due to the nature of their use, are not warranted. Santec recommended custom finishes carry a ten (10) years limited warranty against manufacturing defects and tarnish to the original purchaser with the exclusion of kitchen and pop -up drain assemblies which, due to the nature of their use, are not warranted.
2. Cartridges: Santec Cartridges carry a lifetime limited warranty against manufacturing defects for the life of the product to the original purchaser.
3. Parts: Santec parts carry a Ten (10) year limited warranty against manufacturing defects, to the
4. Warranty exclusions and limitations : This warranty does not cover: damage due to negligence,
original purchaser.
accident, abuse, improper installation, or improper maintenance such as, but not limited to: heat from soldering during installation, the use of plumbers putty, damage from tools used during installation, the use or exposure to chemicals or cleaning products either abrasive or non abrasive or the use of any cleaning tool or product other than a soft, clean cloth. This warranty does not cover: changes in the finish or in the product due to normal wear or aging and does not cover any product or parts which have been altered or used in a manner not typical for the product.
cover and Santec will not be held liable for damage to products caused by the freight carrier and a claim should be made immediately to the freight carrier should this occur. This warranty
does not cover any cost involved in the installation, repair, or replace ment of any Santec product or part. This warranty does not cover and Santec will not be held liable for any loss, damages, or expenses, incidental or consequential whatsoever, originating from the purchase, installation, use, repair, failure, or replaceme nt of any Santec product or part, as allowed by law. The product or components of the covered product will either be repaired, refinished or replaced, at the sole discretion of Santec. Santec reserves the right to examine any product claimed defective pr ior to any warranty claim being accepted or processed, at its sole discretion. This warranty gives you specific legal rights and you may have other rights which may vary from state to state.
This warranty does not
Effective 01/01/03 - Replaces and supersedes any previously issued warranty.
FINISH CARE INFORMATION
For clear coated or enamel color finishes:
We recommend that all faucets, drains, etc. be gently wiped dry with a soft cloth after use to avoid water spotting and water deposit buildup. A mild liquid hand soap, s occasionally if desired. Use of a non -abrasive carnauba wax will add protection to the finish and should be used if the faucets will not be dried after use. Santec Orobrass kitchen products are clear coated.
uch as Ivory may be used
For non-clear coated and specialty finishes:
We recommend that all faucets, drains, etc. be gently wiped dry with a soft cloth after use to avoid water spotting and water deposit buildup. Use of a non-abrasive carnauba wax is required occasionally.
KITCHEN PULL OUT FAUCET ASSEMBLY
1
3
6
P/N
ITEM
PK2755S
1
PK2751
2
PK2752
3
PK2753
4
Pk2754
5 6 EU 3702 UNDERBODY ASSEMBLY (BOXED), MODERN KITCHEN
SPRAYER SUB-ASSEMBLY, (MODERN FAUCET) SPOUT, MODERN KITCHEN PULLOUT FAUCET BODY BASE, MODERN KITCHEN PULLOUT FAUCET HUB, SINGLE HANDLE MODERN KITCHEN LEVER, MODERN KITCHEN PULLOUT FAUCET
DESCRIPTION
QTY.
1 1 1 1 1 1
2
5
4
INSTALLATION INSTRUCTION
KEEP THIS BOOKLET FOR FUTURE REFERENCE
Fig. 1
Fig. 3
Fig. 6
Fig. 2
Fig. 4
Fig. 5
Fig. 7
Fig. 8
Dear Customer,
Before Proceeding with the assembly it is advisable to purge the hot and cold water piping to prevent accumulation of dirt and residues which could cause malfunctioning of the mixer.
INSTALLATIONS
Fig.1:
Insert the mixer into the hole of the sink after placing the gasket (A) into the base of the mixer unit.
Fig. 2:
Fit the flexible tube of the Shower into the washer (D) and the threaded pipe (E), interposing the performed gasket (B), and the flange (C), then block the mixer in position.
Fig. 3:
Connect the flexible tube of the shower (H) with the outlet (F) interposing the gasket (G). Connect the pipe fittings (L) to the water supply tube (L); to complete the installation hook the counter weight on (I) and make sure the pipe run is long enough to pull out the hand shower.
Fig. 4:
Test the functioning of the mixer: while turning the water on the jet flows from the spout/aerator;press on the front side of the push button to deviate the flow back to the aerator; pres on the rear of the push button to return the flow to the original position.
MAINTENANCE
Fig. 5:
It’s been advise to periodically clean the aerator/spout to avoid accumulation of dirt and residues which could in time reduce the flow capacity. To dissemble the aerator unscrew the gasket (o) and clean the filter (N) of all residues. To reassemble it, proceed in reverse making sure to correctly insert the washer (M). Clean the mixer only with water and a soft cloth. It is absolutely not advisable to use solid or liquid detergents, or in any case soaps of any kind because they could damage the treated surface.
Fig. 6- 7 - 8:
If it becomes necessary to replace the cartridge loosen the screw (P) and the screw bolt (Q) on the bottom part of the handle; remove the handle and the mixer unit and then the fastening sleeve (S). Remove the cartridge (R) to reassemble the whole unit proceed in reverse making sure to clean the base of the gaskets. To reassemble the handle check that the screw (O) be exactly in line with the threaded ring (T) on the fastening sleeve.
PAGE 01
Loading...