Santec 6650BO-TM User Manual

ESTATE SERIES BRAVO/MAGGIO COLLECTION

ROMAN TUB FILLER TRIM

WITH “BO” HANDLES

Roman Tub Filler Trim

MODEL: 6650BO10-TM

Flush both supply lines before installation. After ushing shut off both supply lines.

6650BO75-TM

Hole size for the spout and handle trim is a minimum of 1¼” and a maximum of 1½”.

1. Spout Installation

From the top of the deck, insert the spout onto the top of quick connect shank.

Align the spout and tighten the set screw with the large Allen key. Insert the spout plug into the spout back hole.

NOTE: For better installation it is advisable to place silicone caulking around all holes on the top of the deck.

Metal Washer Brass Lock Nut

2. Handle Trim Installation

Screw the handle trim onto the upper lock nut of installed valve.

Adjust the handle alignment in respect to the spout.

Make sure that the handle turns freely in both direction and tighten the brass lock nut rmly. If the handle is scraping against the stem, lower the valve body to reduce the friction.

Repeat the same process for the opposite side handle.

Upper Lock Nut

Rubber Washer

Fiber Washer

Brass Lock Nut

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

Important : Please register your product online at www.santecfaucet.com within 30 days of purchase. Santec reserves the right to request additional documents before servicing warranty requests.

Roman Tub Filler Trim

3. Flush the Line

After all the connections have been made, remove the aerator housing, basket, and washer.

Turn on the water - both hot and cold sides - and ush the line for 45 seconds.

Turn off the water and reinsert the washer, basket, and housing.

Turn on the water and check for leakages at all joints. If water leaks from any of the connections tighten the connection until the leakage stops.

SANTEC LIFETIME LIMITED WARRANTY

Finishes: Santec Polished Chrome, Polished Nickel and Satin Nickel nishes carry a Lifetime Limited warranty against manufacturing defects and tarnish to the original purchaser with the exclusion of kitchen drain assemblies which, due to the nature of their use, are not warranted. Santec recommended custom nishes carry a ten (10) years limited warranty against manufacturing defects and tarnish to the original purchaser with the exclusion of kitchen and pop-up drain assemblies which, due to the nature of their use, are not warranted. Kitchen products carry a three (3) year limited warranty.

Cartridges: Santec Cartridges carry a lifetime limited warranty against manufacturing defects for

2. the life of the product to the original purchaser.

Parts: Santec parts carry a ten (10) year limited warranty against manufacturing defects, to the original purchaser. Kitchen products carry a ve (5) year limited warranty.

Warranty exclusions and limitations: This warranty does not cover: damage due to negligence,

4. accident, abuse, improper installation, or improper maintenance such as, but not limited to: heat from soldering during installation, the use of plumbers putty, damage from tools used during installation, the use or exposure to chemicals or cleaning products either abrasive or non abrasive or the use of any cleaning tool or product other than a soft, clean cloth. Pop-up assemblies are not covered under warranty. This warranty does not cover: changes in the nish or in the product due to normal wear or aging and does not cover any products or parts which have been altered or used in a manner not typical for the product. This warranty does not cover and Santec will not be held liable for damage to products caused by the freight carrier and a claim should be made immediately to the freight carrier should this occur. This warranty does not cover any cost involved in the installation, repair, or replacement of any Santec product or part. This warranty does not cover and Santec will not be held liable for any loss, damages, or expenses, incidental or consequential whatsoever, originating from the purchase, installation, use, repair, failure, or replacement of any Santec product or part, as allowed by law. The product or components of the covered product will either be repaired, renished or replaced, at the sole discretion of Santec. Santec reserves the right to examine any product claimed defective prior to any warranty claim being accepted or processed, at its sole discretion. This warranty gives you specic legal rights and you may have other rights which may vary from state to state.

Hot Valve

Hot

Water

Supply

Cold

Water

Supply

Cold Valve

Effective 01/01/09 - Replaces and supersedes any previously issued warranty

FINISH CARE INFORMATION

For clear coated or enamel color nishes:

We recommend that all faucets, drains, etc be gently wiped dry with a soft cloth after use to avoid water spotting and water deposit buildup. A mild liquid hand soap, such as Ivory may be used occasionally if desired. Use of non-abrasive carnauba wax will add protection to the nish and should be used if the faucets will not be dried after use.

For non-clear coated and specialty nishes:

We recommend that all faucets, drains, etc be gently wiped dry with a soft cloth after use to avoid water spotting and water deposit buildup. Use of a non-abrasive carnauba wax is required occasionally.

PLEASE REGISTER YOUR PRODUCT ONLINE FOR WARRANTY SERVICES

www.santecfaucet.com/registration