Santec 4470CO User Manual
COLOGNE COLLECTIONCOLOGNE COLLECTION
BIDET FITTING WITH “CO” HANDLESBIDET FITTING WITH “CO” HANDLES
ITEM NUMBER
4470CO _ _-_ _
##
11
22
33
44
55
11
66
77
88
99
1010
22
22
1111
1212
PARTPART
DESCRIPTIONDESCRIPTION
Complete Vacuum Breaker Trim *Complete Vacuum Breaker Trim *
Complete Lever HandleComplete Lever Handle
Hot Cartridge OnlyHot Cartridge Only
Cold Cartridge OnlyCold Cartridge Only
Y- Connector Y- Connector
Complete Vacuum Breaker CartridgeComplete Vacuum Breaker Cartridge
Connecting Hose for the Aerator Connecting Hose for the Aerator
Complete Cold ValveComplete Cold Valve
Valve Body Mounting HardwareValve Body Mounting Hardware
Complete Hot ValveComplete Hot Valve
Aerator Housing, Insert, Flange & HardwareAerator Housing, Insert, Flange & Hardware
Complete Lift Knob, Rod and Hardware *Complete Lift Knob, Rod and Hardware *
Assembly *Assembly *
PART #PART #
BD4200-4cap
BD4200-4cap
BD4200-1Cylinder
BD4200-1Cylinder
BD4200-3 ring
BD4200-3 ring
P0418P0418
P0419P0419
PM-B100KPM-B100K
BD4100BD4100
PM-B100GPM-B100G
P0467P0467
P0466P0466
BD4600-5 housing
BD4600-5 housing
BD4600-6 Base
BD4600-6 Base
BD4200-8 knob *
BD4200-8 knob *
BD4200-7 flange *
BD4200-7 flange *
BD4200-9 Rod *
BD4200-9 Rod *
66
7 7
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
44
SANTECSANTEC
88
99
1212
1010
33
SANTECSANTEC
99
5 5
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
1111
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
.
AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”
VACUUM BREAKER INSTALLATION
1
- Remove the complete vacuum breaker trim from the cartridge.
From the underneath of the sink, insert the vacuum breaker cartridge through the
center hole of the sink with the one of 2 conical black Soft Seating China Seals inserted.
- From the top of the sink, insert the second black Soft Seating China Seal, the White Nylon
Slip Washer, then the black Plastic Inverted Lock Nut onto the Cartridge.
Tighten it firmly.
- Screw the Trim Cylinder onto the Cartridge. Tighten Firmly.
- Slip the Handle onto the Cartridge stem and secure it with the brass screw.
- Clip the Handle Cap onto the Handle after the installation is complete to check for the
water flow options.
4470CO _ _
Handle Cap
Screw
Handle
Trim Cylinder
Black plastic lock nut
White Nylon Slip Washer
Black Soft Seating China Seals
HANDLE TRIM INSTALLATION
1
- For proper handle turning direction, install the handle with the “cold” blue label
at the right side of the sink (looking from the front) and the handle with the “hot”
red label at the left side of the sink.
- Both hot and cold side handle trims are pre-assmbled for faster installation.
- Remove the valve body mounting hardware from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the vacuum breaker. Make sure the handle flange washer
is properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses toward the Y- connector.
2
- From beneath of the basin or counter, screw the valve body mounting
hardware back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.
- Align the lever handle properly against the sink.
Tighten the lock nut until it secures the valve body firmly.
3
- Loop and connect the flexible hoses to the Y-Connector. Tighten to avoid
leakage.
- Connect and tighten the Inlet hoses to the supply lines.
Black Soft Seating China Seals
Rubber washer
SANTEC SANTEC
SANTEC SANTEC
INLET HOSEINLET HOSE
Rubber washer
Metal washer
Brass lock nut
PAGE 02
Loading...